Electric Circuit Theory

Size: px
Start display at page:

Download "Electric Circuit Theory"

Transcription

1 Electric Circuit Theory Nam Ki Min

2 Chapter 18 Two-Port Circuits Nam Ki Min

3 Contents and Objectives 3 Chapter Contents 18.1 The Terminal Equations 18.2 The Two-Port Parameters 18.3 Analysis of the Terminated Two-Port Circuit 18.4 Interconnected Two-Port Circuits Chapter Objectives 1. Be able to calculate any set of two-port parameters with any of the following methods: Circuit analysis; Measurements made on a circuit; Converting from another set of two-port parameters using Table Be able to analyze a terminated two-port circuit to find currents, voltages, impedances, and ratios of interest using Table Know how to analyze a cascade interconnection of two-port circuits.

4 The Terminal Equations 4 Definitions Port : a pair of terminals through which a current may enter or leave a network. - A port is an access to the network and consists of a pair of terminals; the current entering one terminal leaves through the other terminal so that the net current entering the port equals zero. - Two-terminal devices or elements (such as resistors, capacitors, and inductors) result in one-port networks. - Most of the circuits we have dealt with so far are two-terminal or one-port circuits, represented in Fig.(a). Two-port network - Fig.(b) shows a four-terminal or two-port circuit. - In general, a network may have n ports. (a) one-port network (b) two-port network

5 The Terminal Equations 5 Terminal Equations In viewing a circuit as a two-port network, we are interested in relating the current and voltage at one port to the current and voltage at the other port. Figure 18.1 shows the reference polarities of the terminal voltages and the reference directions of the terminal currents. The references at each port are symmetric with respect to each other; that is, at each port the current is directed into the upper terminal, and each port voltage is a rise from the lower to the upper terminal. This symmetry makes it easier to generalize the analysis of a two-port network and is the reason for its universal use in the literature. The most general description of the two-port network is carried out in the s domain.

6 The Terminal Equations 6 Of these four terminal variables, only two are independent. Thus for any circuit, once we specify two of the variables, we can find the two remaining unknowns. There are six different ways in which to combine the four variables: V 1 = z 11 I 1 + z 21 I 2 V 2 = z 21 I 1 + z 22 I 2 (18.1) V 1 = h 11 I 1 + h 12 V 2 I 2 = h 21 I 1 h 22 V 2 (18.5) I 1 = y 11 V 1 + y 12 V 2 I 2 = y 21 V 1 + y 22 V 2 (18.2) I 1 = g 11 V + g 12 I 2 V 2 = g 21 V 1 + g 22 I 2 (18.6) V 1 = a 11 V 2 a 12 I 2 I 1 = a 21 V 2 a 22 I 2 (18.3) V 2 = b 11 V 1 b 12 I 1 I 2 = b 21 V 1 b 22 I 1 (18.4)

7 The Terminal Equations 7 The coefficients of the current and/or voltage variables on the right-hand side of Eqs are called the parameters of the two-port circuit. z parameters : z 11, z 21 z 21, z 22 h parameters : h 11, h 12 h 21, h 22 y parameters : y 11, y 12 y 21, y 22 g parameters : g 11, g 12 g 21, g 22 a parameters : a 11, a 12 a 21, a 22 b parameters : b 11, b 12 b 21, b 22

8 The Two-Port Parameters 8 Definitions and Meanings of Two-port Parameters z-parameters z 11 = V 1 I 1 I2 =0 Ω (18.7) : the impedance seen looking into port 1 when port 2 is open. z 12 = V 1 I 2 I1 =0 Ω (18.8) : a transfer impedance. It is the ratio of the port 1 voltage to the port 2 current when port 1 is open. z 21 = V 2 I 1 I2 =0 Ω (18.9) : a transfer impedance. It is the ratio of the port 2 voltage to the port 1 current when port 2 is open. z 22 = V 2 I 2 I2 =0 Ω (18.10) : the impedance seen looking into port 2 when port 1 is open.

9 The Two-Port Parameters 9 y-parameters y 11 = I 1 V 1 V2 =0 S y 12 = I 1 V 2 V1 =0 S y 21 = I 2 V 1 V2 =0 S y 22 = I 2 V 2 V1 =0 S (18.11) Admittance a-parameters y 11 = I 1 V 1 V2 =0 y 12 = I 1 V 2 V1 =0 Ω (18.12) y 21 = I 2 V 1 V2 =0 S y 22 = I 2 V 2 V1 =0

10 The Two-Port Parameters 10 b-parameters y 11 = I 1 V 1 V2 =0 y 12 = I 1 V 2 V1 =0 Ω y 21 = I 2 V 1 V2 =0 S y 22 = I 2 V 2 V1 =0 (18.13) h-parameters y 11 = I 1 V 1 V2 =0 Ω y 12 = I 1 V 2 V1 =0 y 21 = I 2 V 1 V2 =0 y 22 = I 2 V 2 V1 =0 S (18.14)

11 The Two-Port Parameters 11 g-parameters y 11 = I 1 V 1 V2 =0 S y 12 = I 1 V 2 V1 =0 y 21 = I 2 V 1 V2 =0 y 22 = I 2 V 2 V1 =0 Ω (18.15) Immittance Parameters The two-port parameters are also described in relation to the reciprocal sets of equations. The impedance and admittance parameters are grouped into the immittance parameters. The term immittance denotes a quantity that is either an impedance or an admittance

12 The Two-Port Parameters 12 Transmission Parameters The a and b parameters are called the transmission parameters because they describe the voltage and current at one end of the two-port network in terms of the voltage and current at the other end. The immittance and transmission parameters are the natural choices for relating the port variables. In other words, they relate either voltage to current variables or input to output variables. Hybride Parameters The h and g parameters relate cross-variables, that is, an input voltage and output current to an output voltage and input current. Therefore the h and g parameters are called hybrid parameters.

13 The Two-Port Parameters 13 Relationships Among the Two-Port Parameters Because the six sets of equations relate to the same variables, the parameters associated with any pair of equations must be related to the parameters of all the other pairs. In other words, if we know one set of parameters, we can derive all the other sets from the known set. Because of the amount of algebra involved in these derivations, we merely list the results in Table Here, we do derive those between the z and y parameters and between the z and a parameters. These derivations illustrate the general process involved in relating one set of parameters to another. To find the z parameters as functions of the y parameters, we first solve Eqs.(18.2) for V 1 and V 2. We then compare the coefficients of I 1 and I 2 in the resulting expressions to the coefficients of I 1 and I 2 in Eqs.(18.1). From Eqs.(18.2), V 1 = I 1 y 22 I 2 y 11 y 22 y 12 = y 21 y 22 y 22 y I 1 y 12 y I 2 (18.16) V 2 = y 11 I 1 y 21 I 2 y = y 21 y I 1 + y 11 y I 2 (18.17)

14 The Two-Port Parameters 14 Relationships Among the Two-Port Parameters Comparing Eqs.(18.16) and (18.17) with Eqs.(18.1) shows z 11 = y 22 y (18.17) z 21 = y 21 y (18.20) z 12 = y 12 y (18.17) z 22 = y 11 y (18.21) To find the z parameters as functions of the a parameters, we rearrange Eqs.(18.3) in the form of Eqs.(18.1) and then compare coefficients. From the second equation in Eqs.(18.3), V 2 = 1 a 21 I 1 + a 22 a 21 I 2 (18.22) Therefore, substituting Eq into the first equation of Eqs yields V 1 = a 11 a 21 I 1 + a 11a 22 a 21 a 12 I 2 (18.23)

15 The Two-Port Parameters 15 Relationships Among the Two-Port Parameters From Eq.(18.23), z 11 = a 11 a 21 (18.24) z 21 = 1 a 21 (18.26) From Eq.(18.23), z 12 = a a 21 (18.25) z 22 = a 22 a 21 (18.27)

16 18.2 The Two-Port Parameters 16 Reciprocal Two-Port Circuits If a two-port circuit is reciprocal, the following relationships exist among the port parameters: z 12 = z 21 (18.28) y 12 = y 21 (18.29) a 11 a 22 a 12 a 21 = a = 1 (18.30) b 11 b 22 b 12 b 21 = b = 1 (18.31) h 12 = h 21 (18.32) g 12 = g 21 (18.33) A two-port circuit is reciprocal if the interchange of an ideal voltage source at one port with an ideal ammeter at the other port produces the same ammeter reading.

17 The Two-Port Parameters 17 Reciprocal Two-Port Circuits A reciprocal two-port circuit is symmetric if its ports can be interchanged without disturbing the values of the terminal currents and voltages. Figure 18.6 shows four examples of symmetric two-port circuits. In such circuits, the following additional relationships exist among the port parameters: z 11 = z 22 y 11 = y 22 a 11 = a 22 b 11 = b 22 h 11 h 22 h 12 h 21 = h = 1 g 11 g 22 g 12 g 21 = g = 1 (18.38) (18.39) (18.40) (18.41) (18.42) (18.43) For a symmetric reciprocal network, only two calculations or measurements are necessary to determine all the twoport parameters.

18 Analysis of the Terminated Two-Port Circuit 18 Figure 18.7 shows the s-domain circuit diagram for a typically terminated two-port model. Here, Z g represents the internal impedance of the source, V g the internal voltage of the source, and Z L the load impedance. Analysis of this circuit involves expressing the terminal currents and voltages as functions of the two-port parameters, V g, Z g and Z L. Six characteristics of the terminated two-port circuit define its terminal behavior: the input impedance Z in = V 1 I 1, or the admittance Y in = I 1 V 1 the output current I 2 the Thevenin voltage and impedance (V Th, Z Th ) with respect to port 2 the current gain I 2 I 1 the voltage gain V 2 V 1 the voltage gain V 2 V g

19 Analysis of the Terminated Two-Port Circuit 19 The Six Characteristics in Terms of the z Parameters To illustrate how these six characteristics are derived, we develop the expressions using the z parameters to model the two-port portion of the circuit. Table 18.2 summarizes the expressions involving the y, a, b, h, and g parameters. The derivation of any one of the desired expressions involves the algebraic manipulation of the two-port equations along with the two constraint equations imposed by the terminations. If we use the z-parameter equations, the four that describe the circuit in Fig are V 1 = z 11 I 1 + z 12 I 2 (18.44) V 2 = z 21 I 1 + z 22 I 2 V 1 = V g I 1 Z g (18.45) (18.46) V 2 = I 2 Z L (18.47) Equations(18.46) and (18.47) describe the constraints imposed by the terminations.

20 Analysis of the Terminated Two-Port Circuit 20 The Six Characteristics in Terms of the z Parameters Z in : the impedance seen looking into port 1 Z in = V 1 I 1 V 2 = z 21 I 1 + z 22 I 2 (18.45) V 2 = I 2 Z L (From Fig.18.7) I 2 = z 21I 1 Z L + z 22 (18.48) V 1 = z 11 I 1 + z 12 I 2 (18.44) Z in = V 1 I 1 = z 11 z 12z 21 z 22 + Z L (18.49)

21 Analysis of the Terminated Two-Port Circuit 21 The Six Characteristics in Terms of the z Parameters I 2 : the terminal current V 1 = z 11 I 1 + z 12 I 2 (18.44) V 1 = V g I 1 Z g (18.46) I 1 = V g z 12 I 2 z 11 + Z g (18.50) I 2 = z 21I 1 Z L + z 22 (18.48) I 2 = z 21 V g z 11 + Z g z 22 + Z L z 12 z 21 (18.51)

22 Analysis of the Terminated Two-Port Circuit 22 The Six Characteristics in Terms of the z Parameters V Th : Thévenin voltage The Thévenin voltage with respect to port 2 equals V 2 when I 2 = 0 V 1 = z 11 I 1 + z 12 I 2 V 2 = z 21 I 1 + z 22 I 2 (18.44) (18.45) When I 2 = 0 But V 1 I2 = 0 = z 11 I 1 V 2 I2 = 0 = z 21I 1 = z 21 V 1 z 11 (18.52) V 1 = V g I 1 Z g V 1 = z 11 I 1 V g I 1 = Z g + z 11 V 2 I2 = 0 = V Th = z 21 Z g + z 11 V g (18.53)

23 Analysis of the Terminated Two-Port Circuit 23 The Six Characteristics in Terms of the z Parameters Z Th : Thévenin impedance or output, impedance The Thévenin impedance is the ratio V 2 I 2 when V g is replaced by a short circuit. V 1 = V g I 1 Z g (18.46) When V g = 0 V 1 = I 1 Z g (18.54) Substituting Eq.(18.54) into Eq.(18.44) gives I 1 = z 12I 2 z 11 + Z g (18.55) Substituting Eq.(18.55) into Eq.(18.45) gives V 1 = z 11 I 1 + z 12 I 2 (18.44) V 2 = z 21 I 1 + z 12 I 2 = z 21 z 12 I 2 z 11 + Z g + z 12 I 2 The Thévenin impedance is (18.45) V 2 I 2 V g = 0 = Z Th = z 22 z 12z 21 z 11 + Z g (18.56)

24 Analysis of the Terminated Two-Port Circuit 24 The Six Characteristics in Terms of the z Parameters I 2 I 1 : Current gain I 2 = z 21I 1 Z L + z 22 (18.48) I 2 I 1 = z 21 Z L + z 22 (18.57) V 2 V 1 : Current gain V 2 = I 2 Z L (18.47) I 2 = V 2 V 2 = z 21 I 1 + z 12 I 2 (18.45) = z 21 I 1 + z 22 V 2 Z L (18.58) Z L V 1 = z 11 I 1 + z 12 I 2 z 11 I 1 = V 1 z 12 V 2 Z L (18.44) I 1 = V 1 z 11 + z 12V 2 z 11 Z L (18.59) V 2 V 1 = z 21 Z L = z 21Z L (18.60) z 11 Z L + z 11 z 22 z 12 z 21 z 11 Z L + z

25 Analysis of the Terminated Two-Port Circuit 25 The Six Characteristics in Terms of the z Parameters Voltage ratio V 2 V g : V 1 = z 11 I 1 + z 12 I 2 (18.44) V 1 = V g I 1 Z g (18.46) V 2 = I 2 Z L (18.47) I 1 = z 12 V 2 Z L z 11 + Z g + V g z 11 + Z g (18.61) V 2 = I 2 Z L (18.47) I 2 = V 2 Z L V 2 = z 21 I 1 + z 12 I 2 (18.45) = z 21z 12 V 2 Z L z 11 + Z g + z 21V g z 11 + Z g z 22 Z L V 2 (18.62) The desired voltage ratio V 2 V g : V 2 V g = z 21 Z L z 11 + Z g z 22 + Z L z 12 z 21 (18.63)

A two-port network is an electrical network with two separate ports

A two-port network is an electrical network with two separate ports 5.1 Introduction A two-port network is an electrical network with two separate ports for input and output. Fig(a) Single Port Network Fig(b) Two Port Network There are several reasons why we should study

More information

Two Port Networks. Definition of 2-Port Network A two-port network is an electrical network with two separate ports for input and output

Two Port Networks. Definition of 2-Port Network A two-port network is an electrical network with two separate ports for input and output Two Port Networks Definition of 2-Port Network A two-port network is an electrical network with two separate ports for input and output What is a Port? It is a pair of terminals through which a current

More information

Two Port Network. Ram Prasad Sarkar

Two Port Network. Ram Prasad Sarkar Two Port Ram Prasad Sarkar 0 Two Post : Post nput port Two Post Fig. Port Output port A network which has two terminals (one port) on the one side and another two terminals on the opposite side forms a

More information

One-Port Networks. One-Port. Network

One-Port Networks. One-Port. Network TwoPort s Definitions Impedance Parameters dmittance Parameters Hybrid Parameters Transmission Parameters Cascaded TwoPort s Examples pplications OnePort s v i' 1 OnePort pair of terminals at which a signal

More information

TWO-PORT. C.T. Pan 1. C.T. Pan

TWO-PORT. C.T. Pan 1. C.T. Pan TWO-PORT CRCUTS C.T. Pan 5. Definition of Two-Port Circuits 5. Classification of Two-Port Parameters 5.3 Finding Two-Port Parameters 5.4 Analysis of the Terminated Two-Port Circuit 5.5 nterconnected Two-Port

More information

TWO-PORT NETWORKS. Enhancing Your Career. Research is to see what everybody else has seen, and think what nobody has thought.

TWO-PORT NETWORKS. Enhancing Your Career. Research is to see what everybody else has seen, and think what nobody has thought. C H A P T E R TWO-PORT NETWORKS 8 Research is to see what everybody else has seen, and think what nobody has thought. Albert Szent-Gyorgyi Enhancing Your Career Career in Education While two thirds of

More information

Electric Circuits II Sinusoidal Steady State Analysis. Dr. Firas Obeidat

Electric Circuits II Sinusoidal Steady State Analysis. Dr. Firas Obeidat Electric Circuits II Sinusoidal Steady State Analysis Dr. Firas Obeidat 1 Table of Contents 1 2 3 4 5 Nodal Analysis Mesh Analysis Superposition Theorem Source Transformation Thevenin and Norton Equivalent

More information

Two-Port Networks Introduction

Two-Port Networks Introduction Two-Port Networks ntroduction n general, a network ma have n ports. The current entering one terminal leaves through the other terminal so that the net current entering all ports equals zero. Thus, a two-port

More information

Lecture 23 Date: Multi-port networks Impedance and Admittance Matrix Lossless and Reciprocal Networks

Lecture 23 Date: Multi-port networks Impedance and Admittance Matrix Lossless and Reciprocal Networks Lecture 23 Date: 30.0.207 Multi-port networks mpedance and Admittance Matrix Lossless and Reciprocal Networks ntroduction A pair of terminals through which a current may enter or leave a network is known

More information

Lab #8 Two Port Networks

Lab #8 Two Port Networks Cir cuit s 212 Lab Lab #8 Two Port Networks Network parameters are used to characterize a device. Given the network parameters of a device, the voltage and current characteristics of the device can be

More information

Two-Port Networks Admittance Parameters CHAPTER16 THE LEARNING GOALS FOR THIS CHAPTER ARE THAT STUDENTS SHOULD BE ABLE TO:

Two-Port Networks Admittance Parameters CHAPTER16 THE LEARNING GOALS FOR THIS CHAPTER ARE THAT STUDENTS SHOULD BE ABLE TO: CHAPTER16 Two-Port Networks THE LEARNING GOALS FOR THIS CHAPTER ARE THAT STUDENTS SHOULD BE ABLE TO: Calculate the admittance, impedance, hybrid, and transmission parameter for two-port networks. Convert

More information

EE 205 Dr. A. Zidouri. Electric Circuits II. Two-Port Circuits Two-Port Parameters. Lecture #42

EE 205 Dr. A. Zidouri. Electric Circuits II. Two-Port Circuits Two-Port Parameters. Lecture #42 EE 05 Dr. A. Zidouri Electric Circuits Two-Port Circuits Two-Port Parameters Lecture #4-1 - EE 05 Dr. A. Zidouri The material to be covered in this lecture is as follows: o ntroduction to two-port circuits

More information

Notes for course EE1.1 Circuit Analysis TOPIC 10 2-PORT CIRCUITS

Notes for course EE1.1 Circuit Analysis TOPIC 10 2-PORT CIRCUITS Objectives: Introduction Notes for course EE1.1 Circuit Analysis 4-5 Re-examination of 1-port sub-circuits Admittance parameters for -port circuits TOPIC 1 -PORT CIRCUITS Gain and port impedance from -port

More information

Sinusoidal Steady State Analysis (AC Analysis) Part I

Sinusoidal Steady State Analysis (AC Analysis) Part I Sinusoidal Steady State Analysis (AC Analysis) Part I Amin Electronics and Electrical Communications Engineering Department (EECE) Cairo University elc.n102.eng@gmail.com http://scholar.cu.edu.eg/refky/

More information

Chapter 2. Engr228 Circuit Analysis. Dr Curtis Nelson

Chapter 2. Engr228 Circuit Analysis. Dr Curtis Nelson Chapter 2 Engr228 Circuit Analysis Dr Curtis Nelson Chapter 2 Objectives Understand symbols and behavior of the following circuit elements: Independent voltage and current sources; Dependent voltage and

More information

Chapter 10 AC Analysis Using Phasors

Chapter 10 AC Analysis Using Phasors Chapter 10 AC Analysis Using Phasors 10.1 Introduction We would like to use our linear circuit theorems (Nodal analysis, Mesh analysis, Thevenin and Norton equivalent circuits, Superposition, etc.) to

More information

LAB MANUAL EXPERIMENT NO. 7

LAB MANUAL EXPERIMENT NO. 7 LAB MANUAL EXPERIMENT NO. 7 Aim of the Experiment: Concept of Generalized N-port scattering parameters, and formulation of these parameters into 2-port reflection and transmission coefficients. Requirement:

More information

1.7 Delta-Star Transformation

1.7 Delta-Star Transformation S Electronic ircuits D ircuits 8.7 Delta-Star Transformation Fig..(a) shows three resistors R, R and R connected in a closed delta to three terminals, and, their numerical subscripts,, and, being opposite

More information

Lecture #3. Review: Power

Lecture #3. Review: Power Lecture #3 OUTLINE Power calculations Circuit elements Voltage and current sources Electrical resistance (Ohm s law) Kirchhoff s laws Reading Chapter 2 Lecture 3, Slide 1 Review: Power If an element is

More information

BFF1303: ELECTRICAL / ELECTRONICS ENGINEERING. Alternating Current Circuits : Basic Law

BFF1303: ELECTRICAL / ELECTRONICS ENGINEERING. Alternating Current Circuits : Basic Law BFF1303: ELECTRICAL / ELECTRONICS ENGINEERING Alternating Current Circuits : Basic Law Ismail Mohd Khairuddin, Zulkifil Md Yusof Faculty of Manufacturing Engineering Universiti Malaysia Pahang Alternating

More information

Thevenin equivalent circuits

Thevenin equivalent circuits Thevenin equivalent circuits We have seen the idea of equivalency used in several instances already. 1 2 1 2 same as 1 2 same as 1 2 R 3 same as = 0 V same as 0 A same as same as = EE 201 Thevenin 1 The

More information

TWO PORT NETWORKS Introduction: A port is normally referred to a pair of terminals of a network through which we can have access to network either for a source for measuring an output We have already seen

More information

Chapter 10: Sinusoidal Steady-State Analysis

Chapter 10: Sinusoidal Steady-State Analysis Chapter 10: Sinusoidal Steady-State Analysis 10.1 10.2 10.3 10.4 10.5 10.6 10.9 Basic Approach Nodal Analysis Mesh Analysis Superposition Theorem Source Transformation Thevenin & Norton Equivalent Circuits

More information

Lecture 6: Impedance (frequency dependent. resistance in the s- world), Admittance (frequency. dependent conductance in the s- world), and

Lecture 6: Impedance (frequency dependent. resistance in the s- world), Admittance (frequency. dependent conductance in the s- world), and Lecture 6: Impedance (frequency dependent resistance in the s- world), Admittance (frequency dependent conductance in the s- world), and Consequences Thereof. Professor Ray, what s an impedance? Answers:

More information

Circuit Theorems Overview Linearity Superposition Source Transformation Thévenin and Norton Equivalents Maximum Power Transfer

Circuit Theorems Overview Linearity Superposition Source Transformation Thévenin and Norton Equivalents Maximum Power Transfer Circuit Theorems Overview Linearity Superposition Source Transformation Thévenin and Norton Equivalents Maximum Power Transfer J. McNames Portland State University ECE 221 Circuit Theorems Ver. 1.36 1

More information

Chapter 5. BJT AC Analysis

Chapter 5. BJT AC Analysis Chapter 5. Outline: The r e transistor model CB, CE & CC AC analysis through r e model common-emitter fixed-bias voltage-divider bias emitter-bias & emitter-follower common-base configuration Transistor

More information

Basic. Theory. ircuit. Charles A. Desoer. Ernest S. Kuh. and. McGraw-Hill Book Company

Basic. Theory. ircuit. Charles A. Desoer. Ernest S. Kuh. and. McGraw-Hill Book Company Basic C m ш ircuit Theory Charles A. Desoer and Ernest S. Kuh Department of Electrical Engineering and Computer Sciences University of California, Berkeley McGraw-Hill Book Company New York St. Louis San

More information

D C Circuit Analysis and Network Theorems:

D C Circuit Analysis and Network Theorems: UNIT-1 D C Circuit Analysis and Network Theorems: Circuit Concepts: Concepts of network, Active and passive elements, voltage and current sources, source transformation, unilateral and bilateral elements,

More information

1. Review of Circuit Theory Concepts

1. Review of Circuit Theory Concepts 1. Review of Circuit Theory Concepts Lecture notes: Section 1 ECE 65, Winter 2013, F. Najmabadi Circuit Theory is an pproximation to Maxwell s Electromagnetic Equations circuit is made of a bunch of elements

More information

Single- and Multiport Networks. RF Electronics Spring, 2018 Robert R. Krchnavek Rowan University

Single- and Multiport Networks. RF Electronics Spring, 2018 Robert R. Krchnavek Rowan University Single- and Multiport Networks RF Electronics Spring, 208 Robert R. Krchnavek Rowan University Objectives Generate an understanding of the common network representations of Z, Y, h, and ABCD. To be able

More information

Some of the different forms of a signal, obtained by transformations, are shown in the figure. jwt e z. jwt z e

Some of the different forms of a signal, obtained by transformations, are shown in the figure. jwt e z. jwt z e Transform methods Some of the different forms of a signal, obtained by transformations, are shown in the figure. X(s) X(t) L - L F - F jw s s jw X(jw) X*(t) F - F X*(jw) jwt e z jwt z e X(nT) Z - Z X(z)

More information

Module 13: Network Analysis and Directional Couplers

Module 13: Network Analysis and Directional Couplers Module 13: Network Analysis and Directional Couplers 13.2 Network theory two port networks, S-parameters, Z-parameters, Y-parameters The study of two port networks is important in the field of electrical

More information

Electric Circuit Theory

Electric Circuit Theory Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 11 Sinusoidal Steady-State Analysis Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Contents and Objectives 3 Chapter Contents 11.1

More information

Experiment 9 Equivalent Circuits

Experiment 9 Equivalent Circuits Experiment 9 Equivalent Circuits Name: Jason Johnson Course/Section: ENGR 361-04 Date Performed: November 15, 2001 Date Submitted: November 29, 2001 In keeping with the honor code of the School of Engineering,

More information

AC Circuits Homework Set

AC Circuits Homework Set Problem 1. In an oscillating LC circuit in which C=4.0 μf, the maximum potential difference across the capacitor during the oscillations is 1.50 V and the maximum current through the inductor is 50.0 ma.

More information

M. C. Escher: Waterfall. 18/9/2015 [tsl425 1/29]

M. C. Escher: Waterfall. 18/9/2015 [tsl425 1/29] M. C. Escher: Waterfall 18/9/2015 [tsl425 1/29] Direct Current Circuit Consider a wire with resistance R = ρl/a connected to a battery. Resistor rule: In the direction of I across a resistor with resistance

More information

ECE 202 Fall 2013 Final Exam

ECE 202 Fall 2013 Final Exam ECE 202 Fall 2013 Final Exam December 12, 2013 Circle your division: Division 0101: Furgason (8:30 am) Division 0201: Bermel (9:30 am) Name (Last, First) Purdue ID # There are 18 multiple choice problems

More information

Sophomore Physics Laboratory (PH005/105)

Sophomore Physics Laboratory (PH005/105) CALIFORNIA INSTITUTE OF TECHNOLOGY PHYSICS MATHEMATICS AND ASTRONOMY DIVISION Sophomore Physics Laboratory (PH5/15) Analog Electronics Active Filters Copyright c Virgínio de Oliveira Sannibale, 23 (Revision

More information

Impedance and Admittance Parameters

Impedance and Admittance Parameters 1/31/011 mpedance and Admittance Parameters lecture 1/ mpedance and Admittance Parameters Say we wish to connect the put of one circuit to the input of another. #1 put port input port # The terms input

More information

Study Notes on Network Theorems for GATE 2017

Study Notes on Network Theorems for GATE 2017 Study Notes on Network Theorems for GATE 2017 Network Theorems is a highly important and scoring topic in GATE. This topic carries a substantial weight age in GATE. Although the Theorems might appear to

More information

Chapter 18. Direct Current Circuits

Chapter 18. Direct Current Circuits Chapter 18 Direct Current Circuits Sources of emf The source that maintains the current in a closed circuit is called a source of emf Any devices that increase the potential energy of charges circulating

More information

Chapter 5. Department of Mechanical Engineering

Chapter 5. Department of Mechanical Engineering Source Transformation By KVL: V s =ir s + v By KCL: i s =i + v/r p is=v s /R s R s =R p V s /R s =i + v/r s i s =i + v/r p Two circuits have the same terminal voltage and current Source Transformation

More information

Electric Circuits I FINAL EXAMINATION

Electric Circuits I FINAL EXAMINATION EECS:300, Electric Circuits I s6fs_elci7.fm - Electric Circuits I FINAL EXAMINATION Problems Points.. 3. 0 Total 34 Was the exam fair? yes no 5//6 EECS:300, Electric Circuits I s6fs_elci7.fm - Problem

More information

Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science : Circuits & Electronics Problem Set #1 Solution

Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science : Circuits & Electronics Problem Set #1 Solution Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science 6.2: Circuits & Electronics Problem Set # Solution Exercise. The three resistors form a series connection.

More information

Single Phase Parallel AC Circuits

Single Phase Parallel AC Circuits Single Phase Parallel AC Circuits 1 Single Phase Parallel A.C. Circuits (Much of this material has come from Electrical & Electronic Principles & Technology by John Bird) n parallel a.c. circuits similar

More information

Chapter III LINEAR ACTIVE TWO-PORTS

Chapter III LINEAR ACTIVE TWO-PORTS Class Notes, 31415 RF-Communication Circuits Chapter III LINEAR ACTIVE TWO-PORTS Jens Vidkjær NB 231 ii Contents III Linear, Active Two-Ports... 1 III-1 Y-Parameter Characterization of Two-Ports... 2 Passive

More information

Electrical Circuits Lab Series RC Circuit Phasor Diagram

Electrical Circuits Lab Series RC Circuit Phasor Diagram Electrical Circuits Lab. 0903219 Series RC Circuit Phasor Diagram - Simple steps to draw phasor diagram of a series RC circuit without memorizing: * Start with the quantity (voltage or current) that is

More information

Chapter 1W Basic Electromagnetic Concepts

Chapter 1W Basic Electromagnetic Concepts Chapter 1W Basic Electromagnetic Concepts 1W Basic Electromagnetic Concepts 1W.1 Examples and Problems on Electric Circuits 1W.2 Examples on Magnetic Concepts This chapter includes additional examples

More information

mywbut.com Lesson 16 Solution of Current in AC Parallel and Seriesparallel

mywbut.com Lesson 16 Solution of Current in AC Parallel and Seriesparallel esson 6 Solution of urrent in Parallel and Seriesparallel ircuits n the last lesson, the following points were described:. How to compute the total impedance/admittance in series/parallel circuits?. How

More information

Kirchhoff's Laws and Circuit Analysis (EC 2)

Kirchhoff's Laws and Circuit Analysis (EC 2) Kirchhoff's Laws and Circuit Analysis (EC ) Circuit analysis: solving for I and V at each element Linear circuits: involve resistors, capacitors, inductors Initial analysis uses only resistors Power sources,

More information

How to measure complex impedance at high frequencies where phase measurement is unreliable.

How to measure complex impedance at high frequencies where phase measurement is unreliable. Objectives In this course you will learn the following Various applications of transmission lines. How to measure complex impedance at high frequencies where phase measurement is unreliable. How and why

More information

Lecture 6: Impedance (frequency dependent. resistance in the s-world), Admittance (frequency. dependent conductance in the s-world), and

Lecture 6: Impedance (frequency dependent. resistance in the s-world), Admittance (frequency. dependent conductance in the s-world), and Lecture 6: Impedance (frequency dependent resistance in the s-world), Admittance (frequency dependent conductance in the s-world), and Consequences Thereof. Professor Ray, what s an impedance? Answers:.

More information

mywbut.com Lesson 6 Wye (Y) - Delta ( ) OR Delta ( )-Wye (Y) Transformations

mywbut.com Lesson 6 Wye (Y) - Delta ( ) OR Delta ( )-Wye (Y) Transformations Lesson 6 Wye (Y) - Delta ( ) O Delta ( )-Wye (Y) Transformations 1 Objectives A part of a larger circuit that is configured with three terminal network Y (or Δ ) to convert into an equivalent Δ (or Y )

More information

Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institution of Technology, Madras

Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institution of Technology, Madras Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institution of Technology, Madras Lecture - 32 Network Function (3) 2-port networks: Symmetry Equivalent networks Examples

More information

(amperes) = (coulombs) (3.1) (seconds) Time varying current. (volts) =

(amperes) = (coulombs) (3.1) (seconds) Time varying current. (volts) = 3 Electrical Circuits 3. Basic Concepts Electric charge coulomb of negative change contains 624 0 8 electrons. Current ampere is a steady flow of coulomb of change pass a given point in a conductor in

More information

Lecture Notes on DC Network Theory

Lecture Notes on DC Network Theory Federal University, Ndufu-Alike, Ikwo Department of Electrical/Electronics and Computer Engineering (ECE) Faculty of Engineering and Technology Lecture Notes on DC Network Theory Harmattan Semester by

More information

Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institute of Technology, Madras

Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institute of Technology, Madras Networks and Systems Prof. V. G. K. Murti Department of Electrical Engineering Indian Institute of Technology, Madras Lecture - 34 Network Theorems (1) Superposition Theorem Substitution Theorem The next

More information

The Impedance Matrix

The Impedance Matrix 0/0/09 The mpedance Matrix.doc /7 The mpedance Matrix Consider the -port microwave device shown below: z ( z ) z z port z z port 0 -port 0 microwave 0 device P z z P z port z P z ( z ) z port 0 ( z ) z

More information

Microwave Network Analysis Lecture 1: The Scattering Parameters

Microwave Network Analysis Lecture 1: The Scattering Parameters Microwave Network Analysis Lecture : The Scattering Parameters ELC 305a Fall 0 Department of Electronics and Communications Engineering Faculty of Engineering Cairo University Outline Review on Network

More information

NETWORK THEORY BEES2211

NETWORK THEORY BEES2211 NETWORK THEORY BEES Prepared by Dr. R.Behera Ms. R.Pradhan Department of Electrical Engineering, I.G.I.T, Sarang, Dhenkanal MODULE NETWORK TOPOLOGY. Introduction: When all the elements in a network are

More information

EE 3120 Electric Energy Systems Study Guide for Prerequisite Test Wednesday, Jan 18, pm, Room TBA

EE 3120 Electric Energy Systems Study Guide for Prerequisite Test Wednesday, Jan 18, pm, Room TBA EE 3120 Electric Energy Systems Study Guide for Prerequisite Test Wednesday, Jan 18, 2006 6-7 pm, Room TBA First retrieve your EE2110 final and other course papers and notes! The test will be closed book

More information

Direct Current Circuits. February 18, 2014 Physics for Scientists & Engineers 2, Chapter 26 1

Direct Current Circuits. February 18, 2014 Physics for Scientists & Engineers 2, Chapter 26 1 Direct Current Circuits February 18, 2014 Physics for Scientists & Engineers 2, Chapter 26 1 Kirchhoff s Junction Rule! The sum of the currents entering a junction must equal the sum of the currents leaving

More information

ECE2262 Electric Circuits. Chapter 1: Basic Concepts. Overview of the material discussed in ENG 1450

ECE2262 Electric Circuits. Chapter 1: Basic Concepts. Overview of the material discussed in ENG 1450 ECE2262 Electric Circuits Chapter 1: Basic Concepts Overview of the material discussed in ENG 1450 1 Circuit Analysis 2 Lab -ECE 2262 3 LN - ECE 2262 Basic Quantities: Current, Voltage, Energy, Power The

More information

ENGG 225. David Ng. Winter January 9, Circuits, Currents, and Voltages... 5

ENGG 225. David Ng. Winter January 9, Circuits, Currents, and Voltages... 5 ENGG 225 David Ng Winter 2017 Contents 1 January 9, 2017 5 1.1 Circuits, Currents, and Voltages.................... 5 2 January 11, 2017 6 2.1 Ideal Basic Circuit Elements....................... 6 3 January

More information

Figure Circuit for Question 1. Figure Circuit for Question 2

Figure Circuit for Question 1. Figure Circuit for Question 2 Exercises 10.7 Exercises Multiple Choice 1. For the circuit of Figure 10.44 the time constant is A. 0.5 ms 71.43 µs 2, 000 s D. 0.2 ms 4 Ω 2 Ω 12 Ω 1 mh 12u 0 () t V Figure 10.44. Circuit for Question

More information

Adjoint networks and other elements of circuit theory. E416 4.Adjoint networks

Adjoint networks and other elements of circuit theory. E416 4.Adjoint networks djoint networks and other elements of circuit theory One-port reciprocal networks one-port network is reciprocal if: V I I V = Where and are two different tests on the element Example: a linear impedance

More information

CHAPTER FOUR CIRCUIT THEOREMS

CHAPTER FOUR CIRCUIT THEOREMS 4.1 INTRODUCTION CHAPTER FOUR CIRCUIT THEOREMS The growth in areas of application of electric circuits has led to an evolution from simple to complex circuits. To handle the complexity, engineers over

More information

y(d) = j

y(d) = j Problem 2.66 A 0-Ω transmission line is to be matched to a computer terminal with Z L = ( j25) Ω by inserting an appropriate reactance in parallel with the line. If f = 800 MHz and ε r = 4, determine the

More information

'XNH8QLYHUVLW\ (GPXQG73UDWW-U6FKRRORI(QJLQHHULQJ. ECE 110 Fall Test II. Michael R. Gustafson II

'XNH8QLYHUVLW\ (GPXQG73UDWW-U6FKRRORI(QJLQHHULQJ. ECE 110 Fall Test II. Michael R. Gustafson II 'XNH8QLYHUVLW\ (GPXQG73UDWW-U6FKRRORI(QJLQHHULQJ ECE 110 Fall 2016 Test II Michael R. Gustafson II Name (please print) In keeping with the Community Standard, I have neither provided nor received any assistance

More information

Thevenin Norton Equivalencies - GATE Study Material in PDF

Thevenin Norton Equivalencies - GATE Study Material in PDF Thevenin Norton Equivalencies - GATE Study Material in PDF In these GATE 2018 Notes, we explain the Thevenin Norton Equivalencies. Thevenin s and Norton s Theorems are two equally valid methods of reducing

More information

Physics 142 AC Circuits Page 1. AC Circuits. I ve had a perfectly lovely evening but this wasn t it. Groucho Marx

Physics 142 AC Circuits Page 1. AC Circuits. I ve had a perfectly lovely evening but this wasn t it. Groucho Marx Physics 142 A ircuits Page 1 A ircuits I ve had a perfectly lovely evening but this wasn t it. Groucho Marx Alternating current: generators and values It is relatively easy to devise a source (a generator

More information

IMPLEMENTING EXTRA ELEMENT THEOREM USING NULLOR APPROACH

IMPLEMENTING EXTRA ELEMENT THEOREM USING NULLOR APPROACH INTERNATIONAL JOURNAL OF CIRCUIT THEORY AND APPLICATIONS Int. J. Circ. ¹heor. Appl., 27, 267 273 (1999) LETTER TO THE EDITOR IMPLEMENTING EXTRA ELEMENT THEOREM USING NULLOR APPROACH V. S. MURALI AND C.

More information

vtusolution.in Initial conditions Necessity and advantages: Initial conditions assist

vtusolution.in Initial conditions Necessity and advantages: Initial conditions assist Necessity and advantages: Initial conditions assist Initial conditions To evaluate the arbitrary constants of differential equations Knowledge of the behavior of the elements at the time of switching Knowledge

More information

AP Physics C. Electric Circuits III.C

AP Physics C. Electric Circuits III.C AP Physics C Electric Circuits III.C III.C.1 Current, Resistance and Power The direction of conventional current Suppose the cross-sectional area of the conductor changes. If a conductor has no current,

More information

AC Circuit Analysis and Measurement Lab Assignment 8

AC Circuit Analysis and Measurement Lab Assignment 8 Electric Circuit Lab Assignments elcirc_lab87.fm - 1 AC Circuit Analysis and Measurement Lab Assignment 8 Introduction When analyzing an electric circuit that contains reactive components, inductors and

More information

MODULE-4 RESONANCE CIRCUITS

MODULE-4 RESONANCE CIRCUITS Introduction: MODULE-4 RESONANCE CIRCUITS Resonance is a condition in an RLC circuit in which the capacitive and inductive Reactance s are equal in magnitude, there by resulting in purely resistive impedance.

More information

Analog Circuits and Systems

Analog Circuits and Systems Analog Circuits and Systems Prof. K Radhakrishna Rao Lecture 5 Analog Signal Processing using One Port Networks, Passive Two Ports and Ideal Amplifiers 1 One Port Devices Passive devices like R, L, C and

More information

Lecture 17 Date:

Lecture 17 Date: Lecture 17 Date: 09.03.017 The Quadrature Hybrid We began our discussion of dividers and couplers by considering important general properties of three- and four-port networks. This was followed by an analysis

More information

CHAPTER 4. Circuit Theorems

CHAPTER 4. Circuit Theorems CHAPTER 4 Circuit Theorems The growth in areas of application of electrical circuits has led to an evolution from simple to complex circuits. To handle such complexity, engineers over the years have developed

More information

LABORATORY MODULE ELECTRIC CIRCUIT

LABORATORY MODULE ELECTRIC CIRCUIT LABORATORY MODULE ELECTRIC CIRCUIT HIGH VOLTAGE AND ELECTRICAL MEASUREMENT LAB ELECTRICAL ENGINEERING DEPARTMENT FACULTY OF ENGINEERING UNIVERSITAS INDONESIA DEPOK 2018 MODULE 1 LABORATORY BRIEFING All

More information

Transient Analysis of Interconnects by Means of Time-Domain Scattering Parameters

Transient Analysis of Interconnects by Means of Time-Domain Scattering Parameters Transient Analysis of Interconnects by Means of Time-Domain Scattering Parameters Wojciech Bandurski, Poznań Univ. of Technology 60-965 Poznań, Piotrowo 3a, Poland, bandursk@zpe.iee.put.poznan.pl INTRODUCTION

More information

I. Impedance of an R-L circuit.

I. Impedance of an R-L circuit. I. Impedance of an R-L circuit. [For inductor in an AC Circuit, see Chapter 31, pg. 1024] Consider the R-L circuit shown in Figure: 1. A current i(t) = I cos(ωt) is driven across the circuit using an AC

More information

R R V I R. Conventional Current. Ohms Law V = IR

R R V I R. Conventional Current. Ohms Law V = IR DC Circuits opics EMF and erminal oltage esistors in Series and in Parallel Kirchhoff s ules EMFs in Series and in Parallel Capacitors in Series and in Parallel Ammeters and oltmeters Conventional Current

More information

Module 4. Single-phase AC circuits. Version 2 EE IIT, Kharagpur

Module 4. Single-phase AC circuits. Version 2 EE IIT, Kharagpur Module 4 Single-phase circuits ersion EE T, Kharagpur esson 6 Solution of urrent in Parallel and Seriesparallel ircuits ersion EE T, Kharagpur n the last lesson, the following points were described:. How

More information

Lecture 19 Date:

Lecture 19 Date: Lecture 19 Date: 8.10.014 The Quadrature Hybrid We began our discussion of dividers and couplers by considering important general properties of three- and fourport networks. This was followed by an analysis

More information

Delhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web: Ph:

Delhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web:     Ph: Serial : CH_EE_B_Network Theory_098 Delhi Noida Bhopal Hyderabad Jaipur Lucknow ndore Pune Bhubaneswar Kolkata Patna Web: E-mail: info@madeeasy.in Ph: 0-56 CLASS TEST 08-9 ELECTCAL ENGNEENG Subject : Network

More information

LINEAR CIRCUIT ANALYSIS (EED) U.E.T. TAXILA 09

LINEAR CIRCUIT ANALYSIS (EED) U.E.T. TAXILA 09 LINEAR CIRCUIT ANALYSIS (EED) U.E.T. TAXILA 09 ENGR. M. MANSOOR ASHRAF INTRODUCTION Thus far our analysis has been restricted for the most part to dc circuits: those circuits excited by constant or time-invariant

More information

Lab 9/14/2012. Lab Power / Energy Series / Parallel Small Signal Applications. Outline. Power Supply

Lab 9/14/2012. Lab Power / Energy Series / Parallel Small Signal Applications. Outline. Power Supply Outline Session 2: Analog Circuits Lab Power / Energy Series / Parallel Small Signal Applications Lab hits Power Supply, Oscilloscope, Breadboard, Multimeters Energy Power an Energy for, L, C Series /

More information

Circuits with Capacitor and Inductor

Circuits with Capacitor and Inductor Circuits with Capacitor and Inductor We have discussed so far circuits only with resistors. While analyzing it, we came across with the set of algebraic equations. Hereafter we will analyze circuits with

More information

Basic RL and RC Circuits R-L TRANSIENTS: STORAGE CYCLE. Engineering Collage Electrical Engineering Dep. Dr. Ibrahim Aljubouri

Basic RL and RC Circuits R-L TRANSIENTS: STORAGE CYCLE. Engineering Collage Electrical Engineering Dep. Dr. Ibrahim Aljubouri st Class Basic RL and RC Circuits The RL circuit with D.C (steady state) The inductor is short time at Calculate the inductor current for circuits shown below. I L E R A I L E R R 3 R R 3 I L I L R 3 R

More information

Series & Parallel Resistors 3/17/2015 1

Series & Parallel Resistors 3/17/2015 1 Series & Parallel Resistors 3/17/2015 1 Series Resistors & Voltage Division Consider the single-loop circuit as shown in figure. The two resistors are in series, since the same current i flows in both

More information

.. Use of non-programmable scientific calculator is permitted.

.. Use of non-programmable scientific calculator is permitted. This question paper contains 8+3 printed pages] Roll No. S. No. of Question Paper 7981 Cnique Paper Code 1\;ame of the Paper ~ame of the Course Semester Duration : 3 Hours 2511102 Circuit Analysis [DC-1.1]

More information

Chapter 2 Voltage-, Current-, and Z-source Converters

Chapter 2 Voltage-, Current-, and Z-source Converters Chapter 2 Voltage-, Current-, and Z-source Converters Some fundamental concepts are to be introduced in this chapter, such as voltage sources, current sources, impedance networks, Z-source, two-port network,

More information

NETWORK ANALYSIS ( ) 2012 pattern

NETWORK ANALYSIS ( ) 2012 pattern PRACTICAL WORK BOOK For Academic Session 0 NETWORK ANALYSIS ( 0347 ) 0 pattern For S.E. (Electrical Engineering) Department of Electrical Engineering (University of Pune) SHREE RAMCHANDRA COLLEGE OF ENGG.

More information

Fundamentals of Electric Circuits, Second Edition - Alexander/Sadiku

Fundamentals of Electric Circuits, Second Edition - Alexander/Sadiku Chapter 3, Problem 9(8). Find V x in the network shown in Fig. 3.78. Figure 3.78 Chapter 3, Solution 9(8). Consider the circuit below. 2 Ω 2 Ω -j 8 30 o I j 4 j 4 I 2 -j2v For loop, 8 30 = (2 j4)i ji 2

More information

Homework 2 SJTU233. Part A. Part B. Problem 2. Part A. Problem 1. Find the impedance Zab in the circuit seen in the figure. Suppose that R = 5 Ω.

Homework 2 SJTU233. Part A. Part B. Problem 2. Part A. Problem 1. Find the impedance Zab in the circuit seen in the figure. Suppose that R = 5 Ω. Homework 2 SJTU233 Problem 1 Find the impedance Zab in the circuit seen in the figure. Suppose that R = 5 Ω. Express Zab in polar form. Enter your answer using polar notation. Express argument in degrees.

More information

SOME USEFUL NETWORK THEOREMS

SOME USEFUL NETWORK THEOREMS APPENDIX D SOME USEFUL NETWORK THEOREMS Introduction In this appendix we review three network theorems that are useful in simplifying the analysis of electronic circuits: Thévenin s theorem Norton s theorem

More information

Chapter 9 Balanced Faults, Part II. 9.4 Systematic Fault Analysis Using Bus Impedance Matrix

Chapter 9 Balanced Faults, Part II. 9.4 Systematic Fault Analysis Using Bus Impedance Matrix Chapter 9 Balanced Faults, Part II 9.4 Systematic Fault Analysis Using Bus Impedance Matrix In the previous analysis we employed the Thevenin model and ound the Thevenin voltage and impedance by means

More information

Scanned by CamScanner

Scanned by CamScanner Scanned by CamScanner Scanned by CamScanner t W I w v 6.00-fall 017 Midterm 1 Name Problem 3 (15 pts). F the circuit below, assume that all equivalent parameters are to be found to the left of port

More information

Physics 102 Lab 4: Circuit Algebra and Effective Resistance Dr. Timothy C. Black Spring, 2005

Physics 102 Lab 4: Circuit Algebra and Effective Resistance Dr. Timothy C. Black Spring, 2005 Physics 02 Lab 4: Circuit Algebra and Effective Resistance Dr. Timothy C. Black Spring, 2005 Theoretical Discussion The Junction Rule: Since charge is conserved, charge is neither created or destroyed

More information