Metal-Case Tubular Metalized PPS Film Capacitors

Transcription

1 Metalized Polyphenylene Sulfide Metal-Case Tubular Metalized PPS Film Capacitors Type 820P EECTRICA SPECIFICATIONS Capacitance Range: 0.01 μf to 15.0 μf C Voltage Range: 50 VC to 400 VC AC Voltage Range: 32 to 240 VRMS Capacitance Tolerance: ±%, ±5%, ±2%, ±1% Features Superior performance, polycarbonate replacement High current High Q, low TCC High reliability Rugged construction Small size Hermetically sealed Meets the requirements of MI-PRF / 13 Major Applications: Storage, filtering, timing, integrating, and applications where severe environments require hermetically sealed cases. PHYSICA CHARACTERISTICS Construction: Non-inductive wound metalized polyphenylene sulfide. Case: Hermetically sealed metal enclosure. Styles and dimensions are in Guide to Ordering section in the front of the catalog. ead Material: Solder coated solid wire. ead Wire Sizes: Case ia. ead AWG Case ia. ead AWG and No and No thru No No. 18 ead Pull: 5 lbs (2.3 kg) for one minute. No physical damage. ead Bend: After three complete consecutive bends. No damage. Operating Temperature: AC operation limited to +5 C Voltage erating: At +5 C, 70% of the rating At +125 C, 50% of the rating issipation Factor: 0.15% maximum when 25 C Voltage Test: 200% of rated voltage for 2 minutes Insulation Resistance: Measured at rated VC after a 2 minute charge. At +25 C, 0,000 Megaohm-Microfarads, need not exceed 200,000 Megaohms At +85 C, 6,000 Megaohm-Microfarads, need not exceed 25,000 Megaohms At +125 C, 1,000 Megaohm-Microfarads, need not exceed 15,000 Megaohms MAXIMUM PUSE RISE TIME Capacitor Rise Time dv / dt (V / μs) ength (inch) 50 V 0 V 200 V 400 V Marking: earborn trademark, type or catalog number, capacitance, tolerance and voltage. 37

2 Type 820P Metalized Polyphenylene Sulfide Metal-Case Tubular Metalized PPS Film Capacitors STANAR RATINGS Capacitance Voltage Code VC / 32 VAC* Voltage Code 0 0 VC / 63 VAC* Voltage Code VC / 126 VAC* Voltage Code VC / 240 VAC* μf Code Additional capacitance values, voltages, and tolerances are available upon request. * AC voltage rating is at 400Hz. 1.4 x VRMS + VC should not exceed the rated VC. * Graphs of AC voltage vs. frequency follow. The dimensions shown above are for styles 02, 04 and 13. The dimensions for other styles are included in the general section in the front of the catalog. 38

3 Metalized Polyphenylene Sulfide Metal-Case Tubular Metalized PPS Film Capacitors Type 820P VOTAGE vs. FREQUENCY TYPE 820P 50 VC / 32 VAC VOTAGE vs. FREQUENCY TYPE 820P 0 VC / 63 VAC 0 VRMS 0 VRMS 63 VRMS 32 VRMS 15.0 µf 1.0 µf 8.2 µf 5.0 µf 1.0 µf 2.7 µf 0.47µF µf.0 µf 0.1 µf 0.47 µf 5.0 µf 2.7 µf 1.0 µf 1 1,000,000 40,000 Frequency (Hz) 1 1,000,000 40,000 Frequency (Hz) VOTAGE vs. FREQUENCY TYPE 820P 200 VC / 126 VAC VOTAGE vs. FREQUENCY TYPE 820P 400 VC / 240 VAC 300 VRMS 300 VRMS 240 VRMS VRMS 5.0 µf 2.7 µf 1.0 µf0.47 µf 0.µF µf 0.01µF µf 1.0 µf 0.47µF 0.µF µf 0.01µF 1 1,000,000 40, ,000,000 40,000 Frequency (Hz) Frequency (Hz) 39

4 General Information on Polyphenlyene Sulfide Capacitors General Electrical, Physical, and Environmental Characteristics Electrical Characteristics: Capacitance, dissipation factor, insulation resistance, and dielectric strength shall be measured as specified. Physical Characteristics: The lead strength shall be measured as specified. Environmental Characteristics: Vibration Test: Units shall be tested as required. As a result of the test no mechanical damage, short, open or intermittent circuit. Moisture Resistance: The hermetically sealed units shall be tested. As a result of the test there shall be: No visible damage Δ C of ± 5% Min. IR = 50% of initial limit F = 0.5% Humidity Test: The non-hermetically sealed units shall be tested. As a result of the test there shall be: No visible damage Δ C of ± 5% Min. IR = 50% of initial limit F = 0.5% C ife: 820P, 842P, 859P are tested in accordance with the applicable Mil Spec. 8P, 832P, 860P & 882P: 140% of rated voltage at 125 C for 250 hours 880P: 125% of rated voltage for 250 hours at 150 C. As a result of the test there shall be: No permanent open or short circuit No visible damage Δ C of ± 5% Min. IR = 50% of initial limit F = 0.3% AC ife: The Type 859P shall be tested at 1% of the rated rms voltage at 400Hz for 250 hours at 85 C. As a result of the test there shall be: No permanent open or short circuit Δ C of ± 5% F = 0.5% No visible damage Min. IR = 50% of initial limit Part Number Polyphenylene Sulfide (Replacement for Polycarbonate) Mil Spec Number Catalog Page Metalized Polycarbonate / Polyphenylene Sulfide Part Number Polycarbonate Mil Spec Number Outline rawing Polycarbonate / Polyphenylene Sulfide escription 859P / P / 7 AC Rated -55 C to +5 C 860P P - Various Configurations 55 C to +5 C 820P / P / Small Size P / 4 / 6 Feed Thru P P - Wrap & Fill 842P / P / 7 Miniature Wrap & Fill 880P High Temp, PPS -55 C to +150 C Film / Foil Polycarbonate / Polyphenylene Sulfide 8P P - Pulse Capacitor 882P Zero TCC PPS Cap Range μf C Voltage Range VAC

5 General Information on Polyphenlyene Sulfide Capacitors Temperature ( C) % Capacitance Change TYPICA ,000,000 0,000 EECTRICA TYPICA VS.,000 TEMPERATURE 1,000 CHARACTERISTICS OF PPS FIM CAPACITORS 0 Insulation Resistance in Megaohms X Microfarads 1.00 % issipation Factor TYPICA AT 1kHz Temperature ( C) wg. No. A-14,582 13

6 Guide to Ordering GROUNE SECTION TO CASE GROUNE TO CASE SECTION INSUATE FROM CASE SECTION INSUATE FROM CASE IMENSIONS IN INCHES imensions (in inches) CASE STYE 01 CASE STYE IMENSIONS IN INCHES imensions (in inches) CASE STYE CASE STYE 02 IA. IA CASE STYE 03 ± INSUATING SEEVE MAX. THICKNESS CASE STYE 12 C IA ±0.005 IA IA. ±0.062 IA CASE STYE 03 C INSUATING SEEVE MAX. THICKNESS CASE STYE 12 IA A C B C B W SOI TINNE EAS ±0.005 FOR IA., ±0.005 FOR IA AN ARGER The length of grounded styles is shorter than the length shown in tabulations in the catalog. ± SOI TINNE EAS CASE STYE W C ±0.31 CASE STYE 04 ±0.31 INSUATING SEEVE MAX THICKNESS CASE STYE 13 INSUATING SEEVE MAX THICKNESS CASE STYE IA WRAP-AROUN C APPROX. 135 FOR IA., AN APPROX. 225 FOR ARGER IA. ±0.005 A C B IA A IA C B WRAP-AROUN APPROX. 135 FOR IA., AN APPROX. 225 FOR ARGER IA ±0.005 FOR IA., ±0.005 FOR IA AN ARGER W ±0.005 FOR IA., ±0.005 FOR IA AN ARGER W ±0.005 FOR IA., ±0.005 FOR IA AN ARGER 19

7 Guide to Ordering Bracket imensions (Style 12 & 13 / in inches) W A B C ± ± ± ± ±0.062 *Based on 1 in. = 25.4 mm TYPICA TAB TERMINA IMENSIONS c ±0.005 c Slot x ±0.062 A B wg. No A-9525 A = ± (3.96 ± 0.38 mm) B = ± (4.75 ± 0.38 mm) Tab Terminal available only on case diameters equal to or greater than inches. T1 & T3 styles are supplied with one tab terminal on the insulated end and a ground lead on the opposite end. 20

8 Ordering tables metal case EXAMPE: 218P 223 X9 0 S 02 Catalog numbering system wrap and fill EXAMPE: 430P 183 X9 0 X F Case style Terminal: S = Wire leads T = Soldering tab*. C Voltage rating: Expressed in volts. See standard ratings charts for voltage code. Capacitance Tolerance: X0 = ±20% X9 = ±% X5 = ±5% X2 = ±2% Capacitance: Expressed in picofarads, the first two digits are significant figures; the third is the number of zeros following. See standard ratings tables for capacitance code. earborn type number: Identifies the basic capacitor. * Soldering tabs are available only on case diameters equal to or greater then inches. Catalog numbering system F applies only to ROHS compliant parts. Terminal: No suffix required unless specified on applicable specification sheet (Terminal style). C Voltage rating: Expressed in volts. See standard ratings charts for voltage code. Capacitance Tolerance: X0 = ±20% X9 = ±% X5 = ±5% X2 = ±2% Capacitance: Expressed in picofarads, the first two digits are significant figures; the third is the number of zeros following. See standard ratings tables for capacitance code. earborn type number: Identifies the basic capacitor. 21