Data Sheet. HDSP-B0xE 18:88 and 88: " Four Digit GaP HER Seven Segment Display. Description. Features

Transcription

1 HSP-x 18:88 and 88:88." our igit ap HR Seven Segment isplay ata Sheet escription The 18:88 and 88:88." our igit Seven Segment isplays have surface painted in neutral gray for enhanced on/off contrast. ll devices are available in either common anode or common cathode configuration with untinted segments. eatures xcellent appearance venly illuminated segments ray face for optimum on/off contrast hoice of colors: HR hoice of character size:. inch

2 Package imensions 88:88." our igit isplay RONT SI RIHT SI 7.8 (.37) (.7) PIN 12 PIN (.23) PIN PIN (.) 19.1 (.72) 1.24 (.) IIT 1 P3 P2 IIT 2 IIT 3 IIT x 3 = 38.1 (1.) 1.2 (2.1) OTTOM SI 7. (.27) 8. (.31) 2.4 x = 1.24 (.). (.2) 4. (.17) NOT: LL IMNSIONS R IN MILLIMTRS (INHS). UNLSS OTHRWIS STT, TOLRNS R ±.2 mm.

3 Package imensions 18:88." our igit isplay RONT SI RIHT SI 7.8 (.37) (.7) PIN 12 PIN (.23) PIN PIN (.) 19.1 (.72) 1.24 (.) P3 P2 IIT 1 IIT 2 IIT 3 IIT x 3 = 38.1 (1.) 1.2 (2.1) OTTOM SI 7. (.27) 8. (.31) 2.4 x = 1.24 (.). (.2) 4. (.17) NOT: LL IMNSIONS R IN MILLIMTRS (INHS). UNLSS OTHRWIS STT, TOLRNS R ±.2 mm. Pin onfiguration unction Pin HSP-1/3 HSP-2/4 1 node athode 2 node athode 3 node P athode P 4 node athode node athode igit 4 ommon athode igit 4 ommon node 7 node athode 8 igit 3 ommon athode igit 3 ommon node 9 igit 2 ommon athode igit 2 ommon node 1 node athode 11 node athode 12 igit 1 ommon athode igit 1 ommon node

4 Internal ircuit iagram HSP-1 (ommon athode) IIT 1 12 IIT 2 9 IIT 3 8 IIT P 3 HSP-2 (ommon node) IIT 1 12 IIT 2 9 IIT 3 8 IIT P 3

5 Internal ircuit iagram HSP-3 (ommon athode) IIT 1 12 IIT 2 9 IIT 3 8 IIT P 3 HSP-4 (ommon node) IIT 1 12 IIT 2 9 IIT 3 8 IIT P 3

6 evices HSP escription 88:88." HR 4 igit, Untinted, ommon athode, isplay 18:88, ray olor Surface 88:88." HR 4 igit, Untinted, ommon node, isplay 18:88, ray olor Surface 88:88." HR 4 igit, Untinted, ommon athode, isplay 88:88, ray olor Surface 88:88." HR 4 igit, Untinted, ommon node, isplay 88:88, ray olor Surface Part Numbering System 8 2 -X X X X-X X X X X H S P-X X X X-X X X X X Mechanical Options [1] : No Mechanical Option olor in Options [1,2] : No olor in Limitation Maximum Intensity in [1,2] : No Maximum Intensity in Limitation Minimum Intensity in [1,2] : No Minimum Intensity in Limitation evice onfiguration/olor [1] : High fficiency Red evice Specific onfiguration [1] Refer to Respective atasheet Package [1] Refer to Respective atasheet Notes: 1. or codes not listed in the figure above, please refer to the respective datasheet or contact your nearest vago representative for details. 2. in options refer to shippable bins for a part number. olor and Intensity ins are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information.

7 bsolute Maximum Ratings escription HR Units verage Power per Segment or P mw Peak orward urrent per Segment or P 1 m orward urrent per Segment or P 2 m Operating Temperature Range 4 to +1 Storage Temperature Range 4 to +1 Reverse Voltage per Segment or P V Wavesoldering Temperature for 3 seconds 1.9 mm below body 2 Note: 1. erate above 4 at.33 m/ for HR. lectrical/optical haracteristics at T = 2 evice Series HSP- Parameter Symbol Min. Typ. Max. Units Test onditions Luminous Intensity/Segment I V 32 µcd I = 1 m (igit verage) orward Voltage/Segment V V I = 2 m or P Peak Wavelength λ PK 32 nm I = 2 m ominant Wavelength λ d 22 nm I = 2 m Luminous Intensity I V-M 2:1 I = 1 m Matching Ratio Reverse urrent I R 1 µ V R = V Notes: 1. Typical specification for reference only. o not exceed absolute maximum ratings. 2. The dominant wavelength, λ d, is derived from the I chromaticity diagram and is that single wavelength which defines the color of the device. Intensity in Limits (Tolerance ± 1%) Rank Symbol ondition Min. Max. Unit L I V I = 1 m 32 µcd M I V I = 1 m 8 µcd

8 MXIMUM URRNT PR SMNT m 3 HIH IINY R (HR) T MINT TMPRTUR igure 1. Maximum allowable average or current vs. ambient temperature. 12 I ORWR URRNT PR SMNT m V ORWR VOLT V igure 2. orward current vs. forward voltage. ontrast nhancement or information on contrast enhancement, please see pplication Note 11. Soldering/leaning leaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning L parts. ll these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic L parts RLTIV LUMINOUS INTNSITY (NORMLIZ TO 1 T 1 m) ORWR URRNT PR SMNT m RLTIV IINY (NORMLIZ TO 1 T 1 m) PK ORWR URRNT PR SMNT m igure 3. Relative luminous intensity vs. forward current. igure 4. Relative efficiency (luminous intensity per unit current) vs. peak current. or product information and a complete list of distributors, please go to our website: vago, vago Technologies, and the logo are trademarks of vago Technologies Limited in the United States and other countries. ata subject to change. opyright 2 vago Technologies Limited. ll rights reserved. Obsoletes N V2-8N - July 4, 27