A01 REVISIONS DWG-CONV, DC-DC, 24VI, 5.1VO RELEASE RLS 7/18/01. Supplier Change Restrictions

Size: px

Start display at page:

Download "A01 REVISIONS DWG-CONV, DC-DC, 24VI, 5.1VO RELEASE RLS 7/18/01. Supplier Change Restrictions"

Margery Wilkerson
5 years ago
Views:

1 REVISIONS WG REV EN NO ESRIPTION PP RELESE RLS 7/8/0 Supplier hange Restrictions FTER NOTIFITION PPROVL Y INTRONIS, IN. THE SUPPLIER S PRT, THE SUPPLIER SHLL NOTIFY INTRONIS OMPONENT ENGINEERING IMMEITELY NY PROPOSE HNGES IN SPEIFITIONS S ONTROLLE Y THEINTRONIS RWING THIS PRT. NO SHIPMENT PRTS ONTINING SUH HNGES SHLL E ME WITHOUT PRIOR PPROVL FROM THE INTRONIS OMPONENT ENGINEERING. FILURE TO HERE TO THIS POLIY SHLL RESULT IN IMMEITE REMOVL SUPPLIER PPROVL. evice Marking S MINIMUM, THE EVIE SHLL E PERMNENTLY N LEGILY MRKE WITH THE FOLLOWING:. MNUFTURER S IENTIFITION.. MNUFTURER S TYPE OR PRT NUMER (IF MNUFTURER S STNR PROUT), OR INTRONIS PRT NUMER (IF NON-STNR PROUT).. MNUFTURER S LOT IENTIFITION N OE.. POLRITY SYMOL OR OTHER ESIGNTE MRKINGS. IF LTERNTE MRKINGS RE REQUIRE OR IF INSUFFIIENT SPE EXISTS FOR THE OVE MINIMUM MRKINGS, EPTLE MRKINGS SHLL E ETERMINE Y OMPONENT ENGINEERING PRIOR TO SHIPMENT PRTS. Shipping Protection PKGE ONTINERS SHLL PROVIE EQUTE PROTETION FOR THE EVIES (INLUING STTI HRGE PROTETION WHEN PPROPRITE) TO WITHSTN NORML HNLING N SHIPPING, N SHLL E LEGILY MRKE WITH OTH THE MNUFTURER S NME N PRT NUMER N THE INTRONIS PRT NUMER N PURHSE ORER NUMER. Supplier Source PPROVE SUPPLIER-SOURE ONTROLLE Y SL. IMENSIONS IN INHES IMENSIONS PPLY EFORE SURFE TRETMENT. THIS RWING ONFORMS TO NSI Y4.5M-98. UNTOLERNE IMENSIONS LOTING TRUE POSITION RE SI. WG-ONV, -, 4VI, 5.VO OMM OE FIRST USE THIS RWING IS THE PROPERTY THE INTRONIS, IN. N MY NOT E OPIE, USE OR ISLOSE FOR NY PURPOSE EXEPT S UTHORIZE IN WRITING Y THE INTRONIS, IN. INSIE RII TO E 0.0 MX. X.XX: X.XXX: NGLES: R. HK. PP. MZ RLS RLS 7/7/0 7/8/0 7/8/0 NORWOO, M 00 WG. SIZE WG NO: SHEET:

2 PRT NUMER REV TULTION ESRIPTION ONV, -, 4VI, 5.VO, W Product escription: Single output,.33w - converter Input: Volts Input Filter:...None, requires an external capacitor Operating ase Temperature Range: to +00 Package:...W x L x 0.4H, plastic Water Washability:...Yes [7] Unless otherwise stated, these specifications apply for T =5, V in =V nom, and maximum rated load []. Parameter Minimum Typ/Nom Maximum Units GENERL: Switching Frequency 400 khz Input to Output Isolation, 0 µ leakage max 850 V Input to Output apacitance,500 picofarads INPUT: Input Voltage Range V Maximum Input Overvoltage, 00ms, no damage 3 V Input urrent, No Load m Input urrent, Maximum Load 350 m Efficiency 79 % Recommended Fuse [] ENVIRONMENTL mbient Operating Range, No erating ase Operating Temperature Range, No erating Storage Range ase Thermal Impedance /Watt Weight. ounces THIS RWING IS THE PROPERTY THE INTRONIS, IN. N MY NOT E OPIE, USE OR ISLOSE FOR NY PURPOSE EXEPT S UTHORIZE IN WRITING Y THE INTRONIS, IN.. NORWOO, M 00 WG. SIZE SHEET: WG NO:

3 Unless otherwise stated, these specifications apply for T =5, V in =V nom, and maximum rated load []. Parameter Minimum Typ/Nom Maximum Units 5. VOLT OUTPUT: Output Voltage, Initial Setpoint V Rated Load Range [] Load Regulation: 50m to % Line Regulation:Vin=Min-Max % Noise, fundamental component [3] mv P-P Noise, 0MHz W [3] mv P-P Load Transient Overshoot [4] 40 mv peak Load Transient Recovery Time N/ µs error band = ±% [4] less than % error Temperature oefficient [5] ppm/ Short ircuit Protection, Output to ommon Load: <0 milliohms [8] ontinuous to MN Output urrent; Shorted Output [8].7 3. Restart after short circuit uto THIS RWING IS THE PROPERTY THE INTRONIS, IN. N MY NOT E OPIE, USE OR ISLOSE FOR NY PURPOSE EXEPT S UTHORIZE IN WRITING Y THE INTRONIS, IN. NORWOO, M 00 WG. SIZE SHEET: WG NO:

4 Notes:. ll parameters measured at T=5 ambient, Vin=4V, and.30 load unless otherwise noted. capacitor is required to be connected to the input pins for proper operation. See input capacitor requirements.. External fusing should be used for system protection due to a catastrophic failure. 3. Output noise is measured with a 0uF tantalum capacitor and a µf ceramic capacitor connected across the output pins. The fundamental component of noise is at the switching frequency and also is commonly referred to as ripple. Using smaller value capacitors will make the output noise slightly higher. n external output capacitor is not required for operation. 4. Load Transient Overshoot is the output voltage peak amplitude referenced to the final value due to a step load change from 0.50 to Load Transient Overshoot and ynamic Response are the same specification. Load Transient Recovery Time is the time for the output to return to within the specified voltage error band centered about the final value. Load Transient Recovery Time and Transient Response are the same specification. Transient response may degrade for low load currents. 5. Temperature coefficient is defined for case temperatures. Output voltage deviation is calculated as the maximum resulting from either ) 5 case to maximum operating case temperature, or ) 5 case to minimum operating case temperature.. No harm if operated at less than 50m load. elow the minimum rated load, the output may exhibit some noise performance degradation. 7. Water washable units will not be damaged by a typical manufacturing water wash process. However, they are not hermetically sealed Test with resistor load of 0 milliohms maximum connected at the pins. THIS RWING IS THE PROPERTY THE INTRONIS, IN. N MY NOT E OPIE, USE OR ISLOSE FOR NY PURPOSE EXEPT S UTHORIZE IN WRITING Y THE INTRONIS, IN.. NORWOO, M 00 WG. SIZE SHEET: WG NO:

5 pplication Notes INPUT PITOR: capacitor must be connected across the input pins for proper operation, located within from the converter. The ripple current and ESR ratings are for >00kHz. The capacitor is selected so the voltage across the input pins is kept to less than 00 mv P-P. The following table lists the requirements. Input Voltage V Power Out Watts apacitor Ripple urrent, -RMS minimum rating ESR, max. milliohms apacitance, min. µf 9 to to THIS RWING IS THE PROPERTY THE INTRONIS, IN. N MY NOT E OPIE, USE OR ISLOSE FOR NY PURPOSE EXEPT S UTHORIZE IN WRITING Y THE INTRONIS, IN.. NORWOO, M 00 WG. SIZE SHEET: WG NO:

6 PIN FUNTION Plastic ase +INPUT -INPUT No Header Filled with Potting ompound 3 +OUTPUT 4 MN (-OUTPUT) Mechanical Outline and onnector Pin ssignments MX HEIGHT INLUING 0.05 STNFS MIN 0.5 MX 0.40 REF OTTOM VIEW SIE VIEW Mechanical tolerances unless otherwise noted: X.XX dimensions: ±0.00 inches. X.XXX dimensions: ±0.00 inches. THIS RWING IS THE PROPERTY THE INTRONIS, IN. N MY NOT E OPIE, USE OR ISLOSE FOR NY PURPOSE EXEPT S UTHORIZE IN WRITING Y THE INTRONIS, IN. O. IN. NORWOO, M 00 WG. SIZE WG NO: SHEET:

C (6) DOORS TYPICAL, ALL SAME SIZE ENCLOSURE, CUSTOM 6 DOOR REVISION HISTORY ZONE REV DESCRIPTION DATE APPROVED 0.01 RELEASE FOR QUOTE 11/16/12 PH

C (6) DOORS TYPICAL, ALL SAME SIZE ENCLOSURE, CUSTOM 6 DOOR REVISION HISTORY ZONE REV DESCRIPTION DATE APPROVED 0.01 RELEASE FOR QUOTE 11/16/12 PH REVISION HISTORY ZONE REV ESRIPTION TE PPROVE 0.0 RELESE FOR QUOTE /6/2 PH 0.02 E ITONL ETL FOR PGO HOO, SE N OORS. RELESE FOR PROUTION 2/4/3 PH 0.03 INRESE OVERLL OF ENLOUSRE 2/8/3 PH 0.04 REVISE OOR