C7400A and C7400C Enthalpy Sensors

Transcription

1 70 and 70 Enthalpy Sensors PROUT T FETURES Senses and combines temperature and humidity of outdoor air. Long lasting thermistor sensing element is accurate and stable over time. s enthalpy of outdoor air increases, the outdoor air damper closes to a preset minimum position. s enthalpy of outdoor air becomes low, the outdoor air damper opens to reduce the mechanical cooling load in the building. Maximum economizer savings is achieved when two 70 Enthalpy Sensors are used for differential enthalpy changeover control. ompact size and lightweight construction allows easy mounting in HV rooftop unit. PPLITION The 70 Enthalpy Sensor is used with the economizer logic modules with the,,, and performance curves; the 70 sensor is used with the logic modules with the,,,, and E performance curves. The sensors combined with the economizer logic modules permit the use of outdoor air as the first stage of cooling in heating, ventilating and air conditioning (HV) systems. Sensor is enclosed in a rugged, corrosion-resistant glassfiber reinforced plastic duct-mount case. Provides a 4 to 20 m output signal to Economizer Logic Module; setpoint is located on the logic module. Put ar ode Here

2 70 N 70 ENTHLPY SENSORS SPEIFITIONS Models: 70 enthalpy sensor for use with economizer logic modules with,,, and performance curves. 70 enthalpy sensor for use with economizer logic modules with,,,, and E performance curves. imensions: See Fig. Output Signal: 4 to 20 m current signal increases from 4 m to 20 m as enthalpy decreases. mbient Temperature Ranges: Shipping: - F to F (- to 66 ) Operating: 32 F to 25 F (0 to 52 ) Maximum Power onsumption: 0. V at 24 Vdc Supply Voltage: 2 to Vdc Electrical onnections: Two /4 in. (6 mm) quick connect terminals. pprovals: Underwriters Laboratories Inc. Flammability Rating: UL94-5V. INSTLLTION When Installing this Product.... Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition. 2. heck the ratings given in the instructions and on the product to make sure the product is suitable for your application. 3. Installer must be a trained, experienced service technician. 4. fter installation is complete, check out product operation as provided in these instructions. 5. Verify polarity of wiring connections from sensor to logic module are correct. UTION Electrical Shock or Equipment amage Hazard. an shock individuals or short equipment circuitry. isconnect power supply before installation. ORERING INFORMTION Follow specific installation instructions furnished by the HV equipment manufacturer. If not available, use this procedure. Fig.. pproximate dimensions of 70 Enthalpy Sensor in inches (mm). Location IMPORTNT When selecting the location, make sure the 70 Enthalpy Sensor is not exposed to rain, snow or direct sunlight. NOTES: The 70 Sensor can be mounted in any position. However, the sensor must be installed where it is exposed to freely circulating air, but protected from rain, snow and direct sunlight. ifferential enthalpy control requires two 70 Sensors. Mount one sensor in the outdoor intake duct, the other in the return air duct. The 70 Sensor is designed to operate in 0 ft./min. minimum airflow. Wiring 5/6 (8) 3-5/32 () 2-3/4 () 9/6 7/32 3-7/8 (96) (6) (25) IMPORTNT ll wiring must agree with applicable codes, ordinances and regulations. Follow the wiring information furnished by the HV equipment manufacturer or see Fig. 2 for typical wiring hookups. S M96 When purchasing replacement and modernization products from your TRELINE wholesaler or distributor, refer to the TRELINE atalog or price sheets for complete ordering number. If you have additional questions, need further information, or would like to comment on our products or services, please write or phone:. Your local Honeywell utomation and ontrol Products Sales Office (check white pages of your phone directory). 2. Honeywell ustomer are 985 ouglas rive North Minneapolis, Minnesota In anada Honeywell Limited/Honeywell Limitée, 35 ynamic rive, Toronto, Ontario MV 4Z9. International Sales and Service Offices in all principal cities of the world. Manufacturing in ustralia, anada, Finland, France, Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S

3 70 N 70 ENTHLPY SENSORS W7459 EONOMIZER PKGE MOUNTE ON TUTOR L (HOT) L2 S 2 TR S O S R TR 5 ENTHLPY SETPOINT TR TR 24 Vac OUTOOR IR ENTHLPY SENSOR 70 S RETURN IR ENTHLPY SENSOR T P T P MINIMUM POSITION OPEN T T P P MIXE IR SENSOR MINIMUM POSITION W7459 EONOMIZER PKGE PROVIE ISONNET MENS N OVERLO PROTETION S REQUIRE. TUTOR 2 ONNET 70 ENTHLPY SENSOR TO TERMINLS S R N FOR IFFERENTIL ENTHLPY ONTROL. REMOVE 620 OHM RESISTOR N MOUNT THE SEON 70 ENTHLPY SENSOR IN RETURN IR. 3 4 SEE LOGI MOULE SPEIFITION FOR ITIONL WIRING INFORMTION. VERIFY POLRITY OF WIRING TO LOGI MOULE IS ORRET. 5 USE 70 SENSOR WITH,,, N PERFORMNE URVE LOGI MOULES N USE 70 SENSOR WITH,,, N E PERFORMNE URVE LOGI MOULES. M2787 Fig. 2. Wiring connections for 70 Enthalpy Sensors. OPERTION ontroller ial Setting ontrol setpoint scale is located on the logic modules. ontrol points (,,,, and E) are field selectable and are used for single enthalpy sensing. Turn to or E (fully clockwise ) when differential enthalpy control is desired. When differential enthalpy control is desired, two enthalpy sensors must be connected to the economizer logic module. See Fig. 2 on page 3. Operation The 70 Enthalpy Sensor is used with an economizer logic module and damper actuator to proportion an outdoor air damper in a ventilation system. Each enthalpy control setpoint (,,, and ) or (,,,, and E) combines temperature and humidity conditions, resulting in the control curve shown in Fig. 5 and 6. When the enthalpy of the outdoor air is below (left of) the appropriate curve, the outdoor air damper can proportion open on a call for cooling from the space thermostat. If the outdoor enthalpy rises above (right of) the control curve, the outdoor air damper closes to the minimum position. NOTE: urves illustrate reset in temperature control point due to changes in relative humidity. For differential enthalpy, turn the control setpoint to or E (fully clockwise ): If outdoor air enthalpy is lower than return air enthalpy, the outdoor air damper proportions open on a call for cooling. If outdoor air enthalpy is higher than return air enthalpy, the outdoor air damper closes to minimum position. ifferential enthalpy control provides energy savings and increased comfort by using the air with the lowest enthalpy. If outdoor air enthalpy and return air enthalpy are equal, the outdoor air damper proportions open on a call for cooling. NOTE: The relationship between the 70 Sensor output current and relative humidity is shown in Fig. 3 and

4 70 N 70 ENTHLPY SENSORS 70 OUTPUT URRENT 70 SENSOR OUTPUT URRENT PERENT RF (0) 4 m 6 m 8 m 0 m 2 m 4 m 6 m 8 m 20 m (6) (2) TEMPERTURE F ( ) Fig Sensor output current versus RH. M227 PERENT RF m (0) 8 m 6 m (6) 4 m 2 m (2) TEMPERTURE ºF ( º) M2786 Fig Sensor output current versus RH. 0 m 8 m 6 m 4 m

5 70 N 70 ENTHLPY SENSORS ONTROL ONTROL POINT URVE PPROX. F ( ) T % RH 73 (23) (2) 67 (9) 63 (7) ENTHLPY TU PER POUN RY IR (2) 45 (7) (0) (6) 55 (3) 65 (8) (2) 75 (24) 85 (29) (35) 20 RELTIVE HUMIITY (%) 05 0 (43) 0 35 (2) 45 (7) (0) 55 (3) (6) 65 (8) (2) 75 (24) PPROXIMTE RY UL TEMPERTURE F ( ) HIGH LIMIT URVE FOR W720, W722, W723, W724, W (29) 95 (35) 05 0 (43) M Fig. 5. Partial psychrometric chart with single 70 Enthalpy Sensor and,,, and Logic Module performance urves

6 70 N 70 ENTHLPY SENSORS ONTROL ONTROL POINT URVE PPROX. F ( ) T % RH 73 (23) (2) 67 (9) 63 (7) E 55 (3) ENTHLPY TU PER POUN RY IR (2) 45 (7) E (0) (6) 55 (3) 65 (8) (2) 75 (24) 85 (29) (35) 20 RELTIVE HUMIITY (%) 05 0 (43) 0 E 35 (2) 45 (7) (0) 55 (3) (6) 65 (8) (2) 75 (24) PPROXIMTE RY UL TEMPERTURE F ( ) HIGH LIMIT URVE FOR W720, W722, W723, W724, W (29) 95 (35) 05 0 (43) M23879 Fig. 6. Partial psychrometric chart with single 70 enthalpy sensor and the,,,, and E logic module performance curves

7 70 N 70 ENTHLPY SENSORS

8 70 N 70 ENTHLPY SENSORS y using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including attorneys fees, arising out of, or resulting from, any modification to the literature by you. utomation and ontrol Solutions Honeywell International Inc. 985 ouglas rive North Golden Valley, MN customer.honeywell.com U.S. Registered Trademark 20 Honeywell International Inc S.. Rev. 2- Printed in United States