Linac Ring Colliders

Size: px

Start display at page:

Download "Linac Ring Colliders"

Lewis Reed
5 years ago
Views:

1 Linac Ring Colliders L. Merminga and G. Krafft, Jefferson Lab V. Lebedev, FNAL and I. Ben-Zvi, BNL The Future of Particle Physics Snowmass 2001 July , Snowmass Village, CO

2 Outline Œ Physics Requirements Œ Two Scenarios Œ Energy Recovery Linacs / The JLab IR FEL Œ Linac Ring Point Designs Œ Accelerator Physics Issues of Protons Œ Accelerator Physics Issues of Energy Recovery Linacs Œ Fundamental Luminosity Limitations Œ R&D Topics Œ Conclusions

3 Physics Requirements Œ Electron proton colliders with the following requirements have recently been proposed as a means for studying hadronic structure: Center-of-mass energy between 14 GeV and 100 GeV with energy asymmetry of about 1 6, which yields E e =3 GeV to 10 GeV and E p =15 GeV to 250 GeV Luminosity at the cm -2 sec -1 level Longitudinal polarization of both beams in the interaction region 50% 80%

4 Two Scenarios Œ Two accelerator design scenarios have been proposed: ring ring linac ring Œ Linac ring option presents advantages with respect to spin manipulations reduction of synchrotron radiation load in the detectors wide range of continuous energy variability Œ Feasibility studies were conducted at BNL (based on RHIC) and Jefferson Lab to determine whether the linac-ring option is viable. Self-consistent sets of parameters were derived Œ Rf power and beam dump considerations require that the electron linac is an Energy Recovery Linac (ERL)

5 Energy Recovery Linacs Œ Energy recovery is the process by which the energy invested in accelerating a beam is returned to the rf cavities by decelerating the same beam. Œ There have been several energy recovery experiments to date, the first one at the Stanford SCA/FEL. Œ Same-cell energy recovery with cw beam current up to 5 ma and energy up to 50 MeV has been demonstrated at the Jefferson Lab IR FEL. Energy recovery is used routinely for the operation of the FEL as a user facility.

6 The JLab 1.7 kw IRFEL and Energy Recovery Demonstration Wiggler assembly G. R. Neil, et al., Sustained Kilowatt Lasing in a Free Electron Laser with Same-Cell Energy Recovery, PRL, Vol 84, Number 4 (2000)

7 The JLab 10 kw IRFEL Upgrade Project

8 Energy Recovery Works Gradient modulator drive signal in a linac cavity measured without energy recovery (signal level around 2 V) and with energy recovery (signal level around 0). GASK Voltage (V) E E E E E E E Time (s)

9 Energy Recovery Works With energy recovery the required linac rf power is ~ 16 kw, nearly independent of beam current. It rises to ~ 36 kw with no recovery at 1.1 ma. 6 5 Beam off 1.1 ma, No ER 1 ma with ER 2.4 ma with ER 3 ma with ER 3.5 ma with ER RF Power (kw) Avg. Cavity number

10 Benefits of Energy Recovery AC Power Draw in IR Demo: 1.7 kw FEL output Beam 5 ma, 48 MeV Component With Energy Recovery (measured) Without Energy Recovery (estimates) Injector RF 220 kw 220 kw Linac RF 175 kw 700 kw He Refrigerator 70 kw 70 kw (Estimated) Magnets, 43 kw 23 kw Computers, etc. Total 508 kw 1013 kw G. R. Neil, FEL Conference 1999, Hamburg Germany.

11 Benefits of Energy Recovery AC Power Draw in IR Upgrade: 10 kw FEL output Beam 10 ma, 160 MeV Component With Energy Recovery (estimates) Without Energy Recovery (estimates) Injector RF 350 kw 350 kw Linac RF 525 kw 4200 kw He Refrigerator 100 kw 100 kw Magnets, 100 kw 40 kw Computers, etc. Total 1075 kw 4690 kw G. R. Neil, FEL Conference 1999, Hamburg Germany

12 RF to Beam Multiplication Factor for an ideal ERL RF to Beam Multiplication Factor E Q E E acc L inj f = 20 MV / m = = 10MeV = 7GeV κ P JE beam f ; PRF ( J 1) E + E 4(/ IrQQ ) J = L G Beam Current [ma] a inj f

13 Benefits of Energy Recovery Œ Required rf power becomes nearly independent of beam current. Œ Increases overall system efficiency. Œ Reduces electron beam power to be disposed of at beam dumps (by ratio of E fin /E inj ). Œ If the beam is dumped below the neutron production threshold, then the induced radioactivity (shielding problem) will be reduced.

14 Linac Ring Schematic Layout Proton Ring Polarized Electron Source Energy Recovery Electron Linac Electron Beam Dump Assume linac uses TESLA-style cavities at 20 MV/m and Q 0 ~1x10 10

15 Linac Ring Collider Reasoning and Point Design 1 Œ Input parameters: E e = 5 GeV and E p = 50 GeV Œ Reasoning: Set electron beam size at IP based on projected source performance Set proton beam parameters at Laslett tuneshift limit Determine number of electrons per bunch Determine collision frequency

16 Electron Beam Parameters at the IP $VVXPH n a PDW4anC (Emittance dilution in linac will be addressed below) At E e = 5 GeV, e = 6 nm )RU * = 10 cm, e * P (Round beams are assumed for electrons and protons)

17 Proton Beam Parameters * Œ For σ β Laslett tuneshift sets a limit on Œ We assume: z p ν = ν L N r C 4 πγ ε 2πσ p p L 3 p x z N p / σ *2 p Œ )RU n,p P/+&5+,& * = 10 cm => p * = 60 P and N p = 1 x at the Laslett tuneshift limit.

18 Number of Electrons per Bunch N e is limited by: Beam-beam tuneshift of proton beam ξ p = N r β 4π γ * e p p *2 pσ e For p = 0.004, N e = 1.1 x 10 10

19 Collision Frequency Œ Maximize f c subject to constraints: Parasitic collisions User requirements based on current understanding Electron cloud effect Œ Assume bunch separation of 6.66 nsec or f c = 150 MHz

20 Luminosity of Point Design 1 L = NN f e p c *2 *2 2 πσ [ e + σ p ] I e = A I p = 2.4 A f c = 150 MHz e * P p * P L = 6.2 x cm -2 sec -1

21 Point Design 2 Œ Input parameters: E e =5 GeV and E p =50 GeV Œ Cooling of protons is assumed Œ Electrons and protons have equal beam size at the IP Œ Electron beam parameters remain the same Œ This optimization yields: I e = A I p = 2.4 A σ e * = 25 µm σ p * = 25 µm L = 2.1 x cm -2 sec -1

22 Point Design 3: The erhic Linac-Ring Scenario Œ Input parameters: E e =10 GeV and E p =250 GeV Œ I e = A I p = 0.83 A σ e * = 33 µm L = 1.14 x cm -2 sec -1 σ p * = 33 µm f c = 56 MHz

23 Parameter Table Parameter Units Point Design 1 Point Design 2 erhic 56 e - Linac p-ring e - Linac p-ring e - Linac RHIC (p) Beam Energy GeV Proton Cooling - - No - Yes - Yes Ring Circumference m N bunch ppb 1.1x x x x x x10 11 f c MHz I ave A σ* µm ε nm β* cm σ z cm ξ pr ν L D e Luminosity cm -2 sec x x x 10 33

24 Accelerator Physics Issues of Protons Œ Intrabeam scattering: Transverse Point design 1: tr = 36 minutes Point design 2: tr = 32 seconds Œ Intrabeam Scattering: Longitudinal Point design 1: tr = 160 minutes # E /E=3e-3 Point design 2: tr = 14 minutes # E /E=3e-3 Œ Collective Effects Longitudinal mode coupling N p <6 x Transverse mode coupling instability N p < 1.8 x 10 12

25 Emittance growth of the electrons due to a single collision Œ A single collision disrupts the electron beam and causes emittance growth Œ Electron beam with degraded phase space has to be recirculated and energy recovered Œ Adiabatic antidamping can result in scraping and beam loss in the cryomodules Œ Therefore, amount of tolerable beam loss at the linac exit imposes a limit on tolerable emittance growth due to collision. This in turn imposes a limit on N p Œ In the small disruption limit: n 2 0,n 2 + (0.194 r e N p ) 2 N p 1.5 x ppb

26 Accelerator Physics Issues of ERLs Œ Source Œ Accelerator Transport Œ Beam Loss Œ Collective Effects Single-bunch effects Multipass, Multibunch Beam Breakup (BBU) Instabilities Œ HOM Power Dissipation

27 High Current Source of Polarized Electrons Œ High average current (~ 250mA), high polarization (~80%) electron source is a significant technological issue State of the art in high average current, polarized sources: ~1 ma at 80% polarization [C. Sinclair, JLab] Hartmann, Sinclair et al., erhic Workshop, April 2000

28 Linac Optics Œ Two beams of different energies must remain confined in the same focusing channel. A possible solution (I. Bazarov, Cornell University) for a 5 GeV ERL beta function (m) beta x beta y acceleration Å position (m) r e c i r c u l a t i o n energy recovery Å

29 Beam Loss Œ IR FEL experience: Loss in the cryomodule 0.1 µa (Radiation measurements) Loss at wiggler entrance < 1 na Loss in recirculation arc 0.1 µa (BLMs) At energies > 10 MeV, beam loss 0.1 µa out of 5 ma 75MHz)

30 Single-bunch Effects Œ Single-bunch, single-pass effects: limit bunch charge Energy spread induced by variation of longitudinal wakefield across bunch For TESLA cavities, k loss ~ 8.5 V/pC at z =1 mm, the induced relative energy spread at 5 GeV is E /E ~ 5 x 10-4 Emittance growth induced by single-bunch transverse BBU N e < 1.5 x Minimize strength of impedance source (SRF better!)

31 Multipass - Multibunch BBU Instabilities Œ Collective effects driven predominantly by high-q superconducting cavities and can potentially limit average current Œ In a recirculating linac, the feedback system formed between beam and cavities is closed and instabilities can result at sufficiently high currents Œ Instabilities can result from the interaction of the beam with transverse HOMs Transverse BBU longitudinal HOMs Longitudinal BBU fundamental accelerating mode Beam Loading Instabilities Œ Transverse BBU is the limiting instability

32 Transverse BBU Instability

33 Transverse BBU (cont d) Œ TDBBU*: 2d beam breakup code used for simulations Œ Simulations give threshold of ~ 230 ma Œ Typical growth rate of the instability is ~2 msecs. Œ Feedback (similar to B-Factories) may be possible (B-Factory bunch-by-bunch feedback at 4 nsecs works!) Œ Experiments in the IRFEL aim towards experimental verification of TDBBU *Developed by Krafft, Bisognano and Yunn

34 FEL BBU Experiment: Preliminary Conclusions Œ Threshold current in the IR FEL varies between 7 ma and 32 ma, under various beam and accelerator configurations Œ Under the nominal FEL configuration, threshold current is between 16 ma and 21 ma Œ For the nominal FEL configuration, TDBBU prediction is 27 ma agreement within ~40% Œ Observed optics dependence has not been quantified yet

35 HOM Power Dissipation Œ Power dissipated by the beam in HOMs, primarily longitudinal: depends on product of bunch charge and average current Pdiss = P 2kQI Œ For TESLA cavities, k loss ~ 8.5 V/pC for z =1 mm and I ave =.264 A P diss ~ 8 kw per cavity Œ IR FEL: I ave = 5 ma, P diss ~ 6 W per cavity Œ Measurements of HOM power vs. bunch charge and bunch repetition frequency were carried out in the IRFEL

36 Measurements of HOM Power vs. Bunch Charge Power in HOM Load (71-74) [Watts] MHz 37.4 MHz 18.7 MHz Power in HOM Load (75-77) [Watts] MHz MHz MHz Bunch Charge [pc] -2 Bunch Charge [pc] k (1) = 1.4 V/pC + k (2) = 8.0 V/pC k total = 9.4 V/pC agreement within 15% k URMEL = 11.0 V/pC

37 Conclusions from HOM Experiment Œ We observed the expected functional dependence of HOM power on bunch charge and bunch repetition frequency: P HOM Q 2 f bunch Œ Loss factor for CEBAF cavities derived from measurements agrees with calculation (URMEL) within 15%

38 Where have all the losses gone? Œ The fraction of HOM power dissipated on cavity walls depends on the bunch length and increases with the HOM frequency, due to Q 0 ~ f 2 degradation from BCS theory Œ It can limit I ave and I peak due to finite cryogenic efficiency Œ A simple analytic model suggests that the fraction on the walls is much less than the fundamental mode load Œ Engineering studies on HOM absorbers are highly recommended

39 Beam-Beam Kink Instability Œ The beam-beam force due to the relative offset between the head of the proton bunch and the electron beam will deflect the electrons. The deflected electrons subsequently interact with the tail of the proton bunch through beam-beam kick. Œ The electron beam acts as a transverse impedance to the proton bunch, and can lead to an instability. Œ In the linear approximation, and disregarding the evolution of the wake within the proton bunch, a stability criterion has been derived [Li, Lebedev, Bisognano, Yunn, PAC 2001] D ξ 4ν e p s Œ For the case of equal bunches and linear beam-beam force, chromaticity appears to increase the threshold of the instability [Perevedentsev, Valishev, PRST 01]. Œ The instability has been observed in numerical simulations [R. Li, J.Bisognano, Phys. Rev. E (1993)] during the beam-beam studies of linac-ring B-Factory. The code is presently being used to simulate unequal bunches and a nonlinear force. We also expect chromaticity to be beneficial in this case.

40 Fundamental Luminosity Limitations 1000 Luminosity [x1e32 cm-2 sec-1] L ξ γε 4 * p p νl fc C ν L = ν L = 0.04 Luminosity = 10 cm sec Proton Energy [GeV] Luminosity vs. proton beam energy at the Laslett and beam-beam tuneshift limits, for two values of the Laslett tuneshift: and In both cases ξ p =0.004

41 Fundamental Luminosity Limitations (cont d) Luminosity [x1e32 cm-2 sec-1] ν L = 0.04 ν L = Luminosity = 10 cm sec L ξ γε 4 * p p νl fc C Proton Energy [GeV]

42 Fundamental Luminosity Limitations (cont d) 1000 Luminosity [x1e32 cm-2 sec-1] L γγνσ e p s *2 f Kink instability limit at c =5 GeV E e Luminosity = 10 cm sec ν L = ν L = Proton Energy [GeV] Luminosity vs. proton beam energy at the stability limit of the beam-beam kink instability (linear approximation: D ξ 4ν ) e p s

43 Fundamental Luminosity Limitations (cont d) Luminosity [x1e32 cm-2 sec-1] = 0.04 = ν L ν L Kink instability limit at Kink instability limit at Luminosity = 10 cm sec L γγνσ e p s =10 GeV E e =5 GeV E e *2 f c Proton Energy [GeV]

44 R&D Topics Œ High average current (~ 250mA), high polarization (~80%) electron source State of the art in high average current, polarized sources: ~1 ma at 80% polarization [C. Sinclair, JLab] Œ High average current demonstration of energy recovery Multibunch beam breakup instability HOM power dissipation Control of beam loss Œ Electron cooling and its ramifications on Laslett and beam-beam tuneshifts Œ Theoretical and if possible, experimental investigation of the beam-beam kink instability

45 Conclusions Œ Self-consistent sets of parameters has been developed for linac-ring colliders Œ Luminosities of several up to appear feasible Œ No accelerator physics showstoppers have been found. Œ Several important issues have been identified that would require focused R&D Œ ERL: Cornell University in collaboration with Jefferson Lab, is proposing a high average current (100 ma), high Energy Recovery Linac (5-7 GeV) for a next generation light source and is planning to address some of the technical issues with a smaller scale prototype (100 ma, 100 MeV) Œ PERL: Similar proposal is being pursued at BNL

46 ERL X-ray X SR Source Conceptual Layout Courtesy I. Bazarov, PAC 2001

47 ERL Prototype We plan to begin work in the fall! 3.5 year construction, 1.5 year measurements Beam Energy Injection Energy Beam current 100 MeV 5 MeV 100 ma Charge per bunch 77 pc Emittance, norm. 2* m Shortest bunch length 100* fs Courtesy I. Bazarov, PAC 2001

48 Example of Interaction Region Design x [cm] s [m] Example of the interaction region design for β* = 6 cm.

ELIC Design. Center for Advanced Studies of Accelerators. Jefferson Lab. Second Electron-Ion Collider Workshop Jefferson Lab March 15-17, 2004

ELIC Design. Center for Advanced Studies of Accelerators. Jefferson Lab. Second Electron-Ion Collider Workshop Jefferson Lab March 15-17, 2004 ELIC Design Ya. Derbenev, K. Beard, S. Chattopadhyay, J. Delayen, J. Grames, A. Hutton, G. Krafft, R. Li, L. Merminga, M. Poelker, E. Pozdeyev, B. Yunn, Y. Zhang Center for Advanced Studies of Accelerators