Name. ME 270 Fall 2005 Final Exam PROBLEM NO. 1. Given: A distributed load is applied to the top link which is, in turn, supported by link AC.
|
|
- John Potter
- 6 years ago
- Views:
Transcription
1 Name ME 270 Fall 2005 Final Exam PROBLEM NO. 1 Given: A distributed load is applied to the top link which is, in turn, supported by link AC. Find: a) Draw a free body diagram of link BCDE and one of link AC. (7 points) b) List any two force members. (2 points) c) Determine the forces at points A, D, and E. (11 points)
2 Name ME 270 Fall 2005 Final Exam PROBLEM NO. 2 Statics short answer. Each part of this problem is worth 5 points. Please answer them as succinctly as possible. 2A. If the tensile force in cable CD is 750 N, calculate the moment exerted by the force in the cable about point A. (5 points)
3 Name 2C. Calculate the y-component of the centroid for the simulated B2 bomber wing. (5 points)
4 Last Name, First Name 2. The device shown below is used to crush cans. The user places the can at point C (the arrow represents the force that the can exerts on the device) and presses down on the handle with a force, P. The force, C, to crush a can is ten pounds when the angle θ = 36.87º. Assume that there is NO Friction on the collar for link BC. 2a. Circle all of the links listed below that are two-force members (3 points) BC AB OP 2b. Draw a free body diagram of link OP (3 points)
5 Last Name, First Name 2c. Draw a free body diagram of link AB (3 points) 2d. Draw a free body diagram of link BC (3 points)
6 Last Name, First Name 2e. Determine the force, P, required to crush a can (4 points) 2f. Determine the reactions at O (4 points)
7 Last Name, First Name 4a. Here is an odd-looking beam assembly. Sometimes these kind of contraptions are used in fail-safe devices. That is, they are designed to fail when a certain load is applied. The beam AC weighs 25 lbs. and beam CD weighs 20 lbs. Draw a free body diagram of link AC and determine the force at point C. (5 points) Draw a free body diagram of link CD and determine the force at point D. (4 points)
8 Name ME 270 Fall 2007 Final Exam PROBLEM NO. 1 (25 points) Short Answer 1A. Please state Newton s three laws as succinctly as possible in order. (5 points) Newton s 1 st Law: Newton s 2 nd Law: Newton s 3 rd Law: 1B. Please fill in the table below. How many scalar equations can be generated for a free body diagram of a particle or a rigid body in two dimensions and three dimensions in static equilibrium. (5 points) 2D 3D Particle Rigid Body
9 Name 1E. A massless wedge is used to move Block B (which weighs 500 lb.) to the right by applying force P. Frictionless rollers are located between the wedge and Block B. Which is the correct free-body diagram: Figure a, Figure b or Figure c? Circle the correct answer and record it in the space provided above. (5 points) P Figure a F w N 1 W Block B 500 lb y N w N 1 75 x F b N b P. Figure b y N w F w N 1 F i W N 1 F i x F b N b P Figure c y N w F w N 1 W N 1 x F b N b
10 Name ME 270 Fall 2007 Final Exam PROBLEM NO. 3 (25 points) Given: A triangular-shaped concrete block is connected to a pin joint at O. The specific weight of the concrete is γ = ρg = 150 lb/ft 3. The specific weight of the water is 62.4 lb/ft 3. The height of the water is at 9 feet (top of the block). The depth (distance out of the paper is 5.00 feet) for the water and the concrete block. There is no friction between the concrete and the ground beneath. A moment, M, is applied to prevent tipping. Find: Determine the weight of the concrete block and its center of mass (4 points). Determine the resultant force and point of application for the water (4 points). Draw a free-body diagram of the concrete block at the instant of impending tipping and specify all loads. (6 points) Determine the minimum moment required so that the concrete block will not tip (8 points all work must be shown) Determine the horizontal force at point O (3 points)
11 Problem 2 ME 270 Fall 2008 Name Part i. By inspection, determine all the zero-force members in the truss below and list them in the box provided (5 points) Zero-force members: Part ii. A 50-lb block with a thickness of 1-ft out of the page is used retain water. The block will not slide. A force P is used to prevent the block from tipping over. The height of water h = 4 ft. a. Please determine the center of mass (x c and y c ) for the block relative to block O. The block is 3-ft wide and 5-ft tall (4 points) b. If the specific weight of the water is given as γ=62.4 lb/ft 3 please determine the force P to prevent tipping about point O (6 points) ii a. x c = y c = ft. ft. y ii b. h= ft. 5-ft h O 3-ft x
12 Problem 8-Practice Final ME 270 Fall 2008 Name A distributed load is also applied to the beam below, determine: a. The magnitude of the distributed load and the point of application (8 points). c. The reactions at the wall of the beam (7 points).
13 Name (Last)(First) 2a.Byinspection,determineallthezero forcemembersinthetrussbelowandlisttheminthebox provided(4points) Zero forcemembers: 2b.A60 lbtriangularblockwithathicknessof1 ftoutofthepageisusedretainwater.theblock willnotslide. a. Pleasedeterminethecenterofmass(x candy c)forthetriangularblockrelativetopointo. Theblockis3 ftwideand5 fttall(4points) b. Ifthespecificweightofthewaterisgivenasγ=62.4lb/ft 3 pleasedeterminetheheightof water,h,thatwillplacethetriangularblockinastateofimpendingtippingaboutpointo(6 points) 2a. x c=ft. y c=ft. 2b. h=ft. 5 ft y h O 3 ft x
14 Name (Last)(First) 2c.PleasestateNewton sthreelawsinorder(6points) 1 st Law 2 nd Law 3 rd Law
15 Name (Last)(First) 4.Thefootpedalisusedtosupportthemass(m=100kg).Notethatthefootpedalisan angledbracketthatconsistsofpointsb,c,andthepointatwhichtheloadisapplied. 4a.Drawafreebodydiagram(withanappropriatecoordinatesystem)ofthefootpedal(B C loadapplicationpoint).notethattheinteriorshaft(denotedbyhiddenlines)isa frictionlesssurfacethatprovidesanegligibleforcetokeepthesystemaligned.(6points) 4b.Determinetheforce,P,requiredtosupportthe100kgload.(5points) 4c.CalculatetheforceinlinkAB.Isitintensionorcompression?(3points)
16 Name (Last) (First) Problem 1a (4 points) Please denote all the ZERO FORCE members in the truss below: Zero Force Members are: Problem 1b (6 points) Please state Newton s Laws in order as succinctly as possible: Newton s First Law Newton s Second Law Newton s Third Law
17 Name (Last) (First) 2. The mechanism below is a model of a can crusher built by students in a basic mechanisms class. The slider mechanism is constructed with link ABC connected to link BD at a pin joint. A slider is attached at point D and slides along the horizontal surface with negligible friction. The force to crush a can is represented by force P (the force the can pushes back on the mechanism). The input to crush the can is force F = 40 lb which acts horizontal to the plane of mechanism. Please show all your work. i. (2 points) Please list all (if any) two force members here. ii. (3 points) Provide a free body diagram for the entire mechanism (please use the figure provided on the next page). iii. (5 points) Provide a free body diagram for the broken up mechanism (please use the figure provided on the next). iv. (10 points) Please determine the reactions at A, and the reaction P for the 40 lb input at the angles shown. Please provide answers here: a. A x = b. A y = c. M A = d. P =
18 Name (Last) (First) Please show work for Part ii here Please show work for Part iii here
19 Last Name:, First Name: 1. The truck shown below is connected to a tree. The angle, θ is 35 o, d1 = 1.8 m, d2 = 1.2 m and the truck weighs 12,000 Newtons. You may assume that the pulley at point B is an ideal pulley. 1a. Draw a free body diagram of the truck assuming that the wheels are free to roll (i.e. the brakes are not engaged). (5 points)
20 Last Name:, First Name: 1b. If the center of mass is a distance, h1 = 0.45 m above the ground and the cable (which is parallel to the hill) is h2 = 0.4 m above the ground, determine the tension in the cable BC. (5 points) 1c. Draw a free body diagram of the truck assuming that the front wheels are free to roll, but the rear wheels are locked (the coefficient of static friction, µs = 0.65). (4 points) 1d. If the back wheels are just on the verge of slipping, what is the tension in the cable BC? (6 points)
21 Last Name:, First Name: 2a. The basketball goal shown below is supported at point O by a cantilevered (also known as a fixed or built- in) support. The vertical beam weighs 65 lbs., the horizontal beam weighs 18 lbs. and Dr. Nauman (200 lbs.) is hanging on the rim at point B. The dimensions z1 = 10 ft., y3 = 4 ft., and y2 = 5 ft. You can neglect the weight of the rim and backboard. (10 points) First, draw a free body diagram of the basketball goal support system. Second, determine the reactions at point O. Free Body Diagram
22 Last Name:, First Name: Problem 3 A simple machine is shown below. A distributed load acts on member AB as shown. Pin joints connect link AB to the wall, link AB to BC, and link BC to the wall on the right. Ignore the masses of the links; the length of member BC is 3 meters. Please use the answer box provided on the following page: a. (3 points) Determine the equivalent force, F r, that can used to replace the distributed load. b. (2 points) Determine the distance from A (along AB) that the equivalent force, F r, will act. c. (5 points) Draw a free-body diagram for each member in the box provided using the members provided, REPLACE the distributed load with a properly located equivalent force. d. (4 points) Determine the magnitude of the force in member BC. e. (2 points) Is the member BC in compression or tension? f. (4 points) Determine the reactions pin joint A in Cartesian coordinates.
23 Last Name:, First Name: Answer Box (a) Fr = (b) Distance Fr acts from point A (c) C A B B Y (d) Magnitude of force in BC: X (e) Is BC in tension or compression? (f) Reactions at pin joint A expressed in Cartesian Coordinates (vector form):
24 Last Name:, First Name: 4c. Please state Newton s laws in order and as succinctly as possible. (4 points) I. II. III.
25 Last Name, First Name 2. Short answer questions 2a. (5 points) Shown below is a single blade wind turbine. The wind causes a drag force on the blade, F 1, in the x direction and a lift force, F 2, in the y direction that causes the blade to spin. You may assume that the forces act at the midpoint of the blade. If d 1 = 20 m, d 2 = 65 m, d 3 = 5m, F 1 = 45 N and F 2 = 225 N, determine the moment that the wind forces cause about the center of the rotating shaft (the origin of the coordinate system). What is the moment about the base of the tower? z y x F 1 d 1 F 2 d 2 d 3
26 Last Name, First Name Problem 3 (20 points). 3. Consider the A-Frame shown below. It is made up of three separate links, AC, CE, and BD. Link BD is attached to the other two with pins and it has a 500 lbs. load attached to it. Draw a free body diagram of the whole structure (4 points). Free body diagram of the whole structure.
27 Last Name, First Name Determine the reactions at A and E (3 points). Draw free body diagrams of each link. (7 points) Link AC Link BD Link CE Then determine the forces at points D and C. (6 points)
Name ME 270 Summer 2006 Examination No. 1 PROBLEM NO. 3 Given: Below is a Warren Bridge Truss. The total vertical height of the bridge is 10 feet and each triangle has a base of length, L = 8ft. Find:
More informationStatics Chapter II Fall 2018 Exercises Corresponding to Sections 2.1, 2.2, and 2.3
Statics Chapter II Fall 2018 Exercises Corresponding to Sections 2.1, 2.2, and 2.3 2 3 Determine the magnitude of the resultant force FR = F1 + F2 and its direction, measured counterclockwise from the
More informationEng Sample Test 4
1. An adjustable tow bar connecting the tractor unit H with the landing gear J of a large aircraft is shown in the figure. Adjusting the height of the hook F at the end of the tow bar is accomplished by
More informationPlease review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam.
Please review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam. Signature: INSTRUCTIONS Begin each problem in the space provided
More informationTUTORIAL SHEET 1. magnitude of P and the values of ø and θ. Ans: ø =74 0 and θ= 53 0
TUTORIAL SHEET 1 1. The rectangular platform is hinged at A and B and supported by a cable which passes over a frictionless hook at E. Knowing that the tension in the cable is 1349N, determine the moment
More informationME C85 / CE C30 Midterm 1 Exam Monday October 4, 2010
Name: SID: ME C85 / CE C30 Midterm 1 Exam Monday October 4, 2010 Please 1. Read through the test before starting. 2. If you re out of space, write on back side and add a note in your solution referring
More informationFinal Exam - Spring
EM121 Final Exam - Spring 2011-2012 Name : Section Number : Record all your answers to the multiple choice problems (1-15) by filling in the appropriate circle. All multiple choice answers will be graded
More information6.6 FRAMES AND MACHINES APPLICATIONS. Frames are commonly used to support various external loads.
6.6 FRAMES AND MACHINES APPLICATIONS Frames are commonly used to support various external loads. How is a frame different than a truss? How can you determine the forces at the joints and supports of a
More informationVector Mechanics: Statics
PDHOnline Course G492 (4 PDH) Vector Mechanics: Statics Mark A. Strain, P.E. 2014 PDH Online PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658 Phone & Fax: 703-988-0088 www.pdhonline.org www.pdhcenter.com
More information5.2 Rigid Bodies and Two-Dimensional Force Systems
5.2 Rigid odies and Two-Dimensional Force Systems 5.2 Rigid odies and Two-Dimensional Force Systems Procedures and Strategies, page 1 of 1 Procedures and Strategies for Solving Problems Involving Equilibrium
More informationMEE224: Engineering Mechanics Lecture 4
Lecture 4: Structural Analysis Part 1: Trusses So far we have only analysed forces and moments on a single rigid body, i.e. bars. Remember that a structure is a formed by and this lecture will investigate
More informationI certify that I have not given unauthorized aid nor have I received aid in the completion of this exam.
Examination No. 2 Please review the following statement: Group Number: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam. Signature: INSTRUCTIONS Begin
More informationREADING QUIZ. 2. When using the method of joints, typically equations of equilibrium are applied at every joint. A) Two B) Three C) Four D) Six
READING QUIZ 1. One of the assumptions used when analyzing a simple truss is that the members are joined together by. A) Welding B) Bolting C) Riveting D) Smooth pins E) Super glue 2. When using the method
More information7.6 Journal Bearings
7.6 Journal Bearings 7.6 Journal Bearings Procedures and Strategies, page 1 of 2 Procedures and Strategies for Solving Problems Involving Frictional Forces on Journal Bearings For problems involving a
More informationAnnouncements. Trusses Method of Joints
Announcements Mountain Dew is an herbal supplement Today s Objectives Define a simple truss Trusses Method of Joints Determine the forces in members of a simple truss Identify zero-force members Class
More informationEQUILIBRIUM OF A RIGID BODY & FREE-BODY DIAGRAMS
Today s Objectives: Students will be able to: EQUILIBRIUM OF A RIGID BODY & FREE-BODY DIAGRAMS a) Identify support reactions, and, b) Draw a free-body diagram. In-Class Activities: Check Homework Reading
More informationSOLUTION 8 1. a+ M B = 0; N A = 0. N A = kn = 16.5 kn. Ans. + c F y = 0; N B = 0
8 1. The mine car and its contents have a total mass of 6 Mg and a center of gravity at G. If the coefficient of static friction between the wheels and the tracks is m s = 0.4 when the wheels are locked,
More informationSimilar to trusses, frames are generally fixed, load carrying structures.
Similar to trusses, frames are generally fixed, load carrying structures. The main difference between a frame and a truss is that in a frame at least one member is a multi force member (çoklu kuvvet elemanı).
More informationEngineering Mechanics: Statics in SI Units, 12e
Engineering Mechanics: Statics in SI Units, 12e 5 Equilibrium of a Rigid Body Chapter Objectives Develop the equations of equilibrium for a rigid body Concept of the free-body diagram for a rigid body
More informationSample 5. Determine the tension in the cable and the horizontal and vertical components of reaction at the pin A. Neglect the size of the pulley.
Sample 1 The tongs are designed to handle hot steel tubes which are being heat-treated in an oil bath. For a 20 jaw opening, what is the minimum coefficient of static friction between the jaws and the
More informationStatic Equilibrium. University of Arizona J. H. Burge
Static Equilibrium Static Equilibrium Definition: When forces acting on an object which is at rest are balanced, then the object is in a state of static equilibrium. - No translations - No rotations In
More informationAnnouncements. Equilibrium of a Rigid Body
Announcements Equilibrium of a Rigid Body Today s Objectives Identify support reactions Draw a free body diagram Class Activities Applications Support reactions Free body diagrams Examples Engr221 Chapter
More informationEquilibrium of a Rigid Body. Engineering Mechanics: Statics
Equilibrium of a Rigid Body Engineering Mechanics: Statics Chapter Objectives Revising equations of equilibrium of a rigid body in 2D and 3D for the general case. To introduce the concept of the free-body
More information1. Please complete the following short problems.
Name 1. Please complete the following short problems. For parts 1A and 1B, we will consider three M88 recovery vehicles pulling an M1 tank back onto the road as shown below. F2 F1 50 M88 #1 50 M88 #2 y
More informationEngineering Mechanics. Friction in Action
Engineering Mechanics Friction in Action What is friction? Friction is a retarding force that opposes motion. Friction types: Static friction Kinetic friction Fluid friction Sources of dry friction Dry
More informationSRSD 2093: Engineering Mechanics 2SRRI SECTION 19 ROOM 7, LEVEL 14, MENARA RAZAK
SRSD 2093: Engineering Mechanics 2SRRI SECTION 19 ROOM 7, LEVEL 14, MENARA RAZAK SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS Today s Objectives: Students will be able to: a) Define a simple
More information1. Replace the given system of forces acting on a body as shown in figure 1 by a single force and couple acting at the point A.
Code No: Z0321 / R07 Set No. 1 I B.Tech - Regular Examinations, June 2009 CLASSICAL MECHANICS ( Common to Mechanical Engineering, Chemical Engineering, Mechatronics, Production Engineering and Automobile
More informationUnit 21 Couples and Resultants with Couples
Unit 21 Couples and Resultants with Couples Page 21-1 Couples A couple is defined as (21-5) Moment of Couple The coplanar forces F 1 and F 2 make up a couple and the coordinate axes are chosen so that
More informationand F NAME: ME rd Sample Final Exam PROBLEM 1 (25 points) Prob. 1 questions are all or nothing. PROBLEM 1A. (5 points)
ME 270 3 rd Sample inal Exam PROBLEM 1 (25 points) Prob. 1 questions are all or nothing. PROBLEM 1A. (5 points) IND: In your own words, please state Newton s Laws: 1 st Law = 2 nd Law = 3 rd Law = PROBLEM
More informationPlease review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam.
Please review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam. Signature: INSTRUCTIONS Begin each problem in the space provided
More informationE 490 FE Exam Prep. Engineering Mechanics
E 490 FE Exam Prep Engineering Mechanics 2008 E 490 Course Topics Statics Newton s Laws of Motion Resultant Force Systems Moment of Forces and Couples Equilibrium Pulley Systems Trusses Centroid of an
More informationThe centroid of an area is defined as the point at which (12-2) The distance from the centroid of a given area to a specified axis may be found by
Unit 12 Centroids Page 12-1 The centroid of an area is defined as the point at which (12-2) The distance from the centroid of a given area to a specified axis may be found by (12-5) For the area shown
More informationSTATICS. Friction VECTOR MECHANICS FOR ENGINEERS: Eighth Edition CHAPTER. Ferdinand P. Beer E. Russell Johnston, Jr.
Eighth E 8 Friction CHAPTER VECTOR MECHANICS FOR ENGINEERS: STATICS Ferdinand P. Beer E. Russell Johnston, Jr. Lecture Notes: J. Walt Oler Texas Tech University Contents Introduction Laws of Dry Friction.
More informationChapter 6: Structural Analysis
Chapter 6: Structural Analysis APPLICATIONS Trusses are commonly used to support a roof. For a given truss geometry and load, how can we determine the forces in the truss members and select their sizes?
More informationENGR-1100 Introduction to Engineering Analysis. Lecture 13
ENGR-1100 Introduction to Engineering Analysis Lecture 13 EQUILIBRIUM OF A RIGID BODY & FREE-BODY DIAGRAMS Today s Objectives: Students will be able to: a) Identify support reactions, and, b) Draw a free-body
More informationF R. + F 3x. + F 2y. = (F 1x. j + F 3x. i + F 2y. i F 3y. i + F 1y. j F 2x. ) i + (F 1y. ) j. F 2x. F 3y. = (F ) i + (F ) j. ) j
General comments: closed book and notes but optional one page crib sheet allowed. STUDY: old exams, homework and power point lectures! Key: make sure you can solve your homework problems and exam problems.
More informationChapter Objectives. Copyright 2011 Pearson Education South Asia Pte Ltd
Chapter Objectives To develop the equations of equilibrium for a rigid body. To introduce the concept of the free-body diagram for a rigid body. To show how to solve rigid-body equilibrium problems using
More informationEQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMEBERS
EQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMEBERS Today s Objectives: Students will be able to: a) Apply equations of equilibrium to solve for unknowns, and, b) Recognize two-force members. In-Class
More informationContinuing Education Course #207 What Every Engineer Should Know About Structures Part B Statics Applications
1 of 6 Continuing Education Course #207 What Every Engineer Should Know About Structures Part B Statics Applications 1. As a practical matter, determining design loads on structural members involves several
More informationNAME: Section: RIN: Tuesday, May 19, :00 11:00. Problem Points Score Total 100
RENSSELAER POLYTECHNIC INSTITUTE TROY, NY FINAL EXAM INTRODUCTION TO ENGINEERING ANALYSIS (ENGR-1100) NAME: Section: RIN: Tuesday, May 19, 2015 8:00 11:00 Problem Points Score 1 20 2 20 3 20 4 20 5 20
More informationEQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMBERS
EQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMBERS Today s Objectives: Students will be able to: a) Apply equations of equilibrium to solve for unknowns, and, b) Recognize two-force members. APPLICATIONS
More informationEngineering Mechanics: Statics STRUCTURAL ANALYSIS. by Dr. Ibrahim A. Assakkaf SPRING 2007 ENES 110 Statics
CHAPTER Engineering Mechanics: Statics STRUCTURAL ANALYSIS College of Engineering Department of Mechanical Engineering Tenth Edition 6a by Dr. Ibrahim A. Assakkaf SPRING 2007 ENES 110 Statics Department
More informationDYNAMICS ME HOMEWORK PROBLEM SETS
DYNAMICS ME 34010 HOMEWORK PROBLEM SETS Mahmoud M. Safadi 1, M.B. Rubin 2 1 safadi@technion.ac.il, 2 mbrubin@technion.ac.il Faculty of Mechanical Engineering Technion Israel Institute of Technology Spring
More information1 MR SAMPLE EXAM 3 FALL 2013
SAMPLE EXAM 3 FALL 013 1. A merry-go-round rotates from rest with an angular acceleration of 1.56 rad/s. How long does it take to rotate through the first rev? A) s B) 4 s C) 6 s D) 8 s E) 10 s. A wheel,
More informationPlease review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam.
Group Number: Please review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam. Signature: INSTRUCTIONS Begin each problem
More informationQ16.: A 5.0 kg block is lowered with a downward acceleration of 2.8 m/s 2 by means of a rope. The force of the block on the rope is:(35 N, down)
Old Exam Question Ch. 5 T072 Q13.Two blocks of mass m 1 = 24.0 kg and m 2, respectively, are connected by a light string that passes over a massless pulley as shown in Fig. 2. If the tension in the string
More informationEquilibrium of a Particle
ME 108 - Statics Equilibrium of a Particle Chapter 3 Applications For a spool of given weight, what are the forces in cables AB and AC? Applications For a given weight of the lights, what are the forces
More informationKINGS COLLEGE OF ENGINEERING ENGINEERING MECHANICS QUESTION BANK UNIT I - PART-A
KINGS COLLEGE OF ENGINEERING ENGINEERING MECHANICS QUESTION BANK Sub. Code: CE1151 Sub. Name: Engg. Mechanics UNIT I - PART-A Sem / Year II / I 1.Distinguish the following system of forces with a suitable
More information1. The horizontal beam represented in Examination Figure 6 carries three loads P 1. and R 2
Student ID: 52573847 Exam: 286037RR - Engineering Mechanics, Part 2 When you have completed your exam and reviewed your answers, click Submit Exam. Answers will not be recorded until you hit Submit Exam.
More informationVALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR DEPARTMENT OF MECHANICAL ENGINEERING
VALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR 603203 DEPARTMENT OF MECHANICAL ENGINEERING BRANCH: MECHANICAL YEAR / SEMESTER: I / II UNIT 1 PART- A 1. State Newton's three laws of motion? 2.
More information11.1 Virtual Work Procedures and Strategies, page 1 of 2
11.1 Virtual Work 11.1 Virtual Work rocedures and Strategies, page 1 of 2 rocedures and Strategies for Solving roblems Involving Virtual Work 1. Identify a single coordinate, q, that will completely define
More informationME 274 Spring 2017 Examination No. 2 PROBLEM No. 2 (20 pts.) Given:
PROBLEM No. 2 (20 pts.) Given: Blocks A and B (having masses of 2m and m, respectively) are connected by an inextensible cable, with the cable being pulled over a small pulley of negligible mass. Block
More informationENGR-1100 Introduction to Engineering Analysis. Lecture 19
ENGR-1100 Introduction to Engineering Analysis Lecture 19 SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS Today s Objectives: Students will be able to: In-Class Activities: a) Define a simple
More information3.1 CONDITIONS FOR RIGID-BODY EQUILIBRIUM
3.1 CONDITIONS FOR RIGID-BODY EQUILIBRIUM Consider rigid body fixed in the x, y and z reference and is either at rest or moves with reference at constant velocity Two types of forces that act on it, the
More informationUNIVERSITY OF SASKATCHEWAN GE MECHANICS III FINAL EXAM APRIL 18, 2011 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS
UNIVERSITY OF SASKATCHEWAN GE 226.3 MECHANICS III FINAL EXAM APRIL 18, 2011 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS LAST NAME (printed): FIRST NAME (printed): STUDENT NUMBER: EXAMINATION
More informationPlease review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam.
Please review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam. Signature: INSTRUCTIONS Begin each problem in the space provided
More informationFE Sta'cs Review. Torch Ellio0 (801) MCE room 2016 (through 2000B door)
FE Sta'cs Review h0p://www.coe.utah.edu/current- undergrad/fee.php Scroll down to: Sta'cs Review - Slides Torch Ellio0 ellio0@eng.utah.edu (801) 587-9016 MCE room 2016 (through 2000B door) Posi'on and
More information8.01x Classical Mechanics, Fall 2016 Massachusetts Institute of Technology. Problem Set 2
8.01x Classical Mechanics, Fall 2016 Massachusetts Institute of Technology 1. Stacked Blocks Problem Set 2 Consider two blocks that are resting one on top of the other. The lower block has mass m 2 = 4.8
More informationPlease review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam.
Please review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam. Signature: INSTRUCTIONS Begin each problem in the space provided
More informationNewton s Third Law Newton s Third Law: For each action there is an action and opposite reaction F
FRAMES AND MACHINES Learning Objectives 1). To evaluate the unknown reactions at the supports and the interaction forces at the connection points of a rigid frame in equilibrium by solving the equations
More informationif the initial displacement and velocities are zero each. [ ] PART-B
Set No - 1 I. Tech II Semester Regular Examinations ugust - 2014 ENGINEERING MECHNICS (Common to ECE, EEE, EIE, io-tech, E Com.E, gri. E) Time: 3 hours Max. Marks: 70 Question Paper Consists of Part- and
More informationThe case where there is no net effect of the forces acting on a rigid body
The case where there is no net effect of the forces acting on a rigid body Outline: Introduction and Definition of Equilibrium Equilibrium in Two-Dimensions Special cases Equilibrium in Three-Dimensions
More informationSIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS
SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS Today s Objectives: Students will be able to: a) Define a simple truss. b) Determine the forces in members of a simple truss. c) Identify zero-force
More informationMechanics of Materials
Mechanics of Materials 2. Introduction Dr. Rami Zakaria References: 1. Engineering Mechanics: Statics, R.C. Hibbeler, 12 th ed, Pearson 2. Mechanics of Materials: R.C. Hibbeler, 9 th ed, Pearson 3. Mechanics
More informationLecture 20. ENGR-1100 Introduction to Engineering Analysis THE METHOD OF SECTIONS
ENGR-1100 Introduction to Engineering Analysis Lecture 20 THE METHOD OF SECTIONS Today s Objectives: Students will be able to determine: 1. Forces in truss members using the method of sections. In-Class
More informationENGR-1100 Introduction to Engineering Analysis. Lecture 20
ENGR-1100 Introduction to Engineering Analysis Lecture 20 Today s Objectives: THE METHOD OF SECTIONS Students will be able to determine: 1. Forces in truss members using the method of sections. In-Class
More informationReview: Advanced Applications of Newton's Laws
Review: Advanced Applications of Newton's Laws 1. The free-body diagram of a wagon being pulled along a horizontal surface is best represented by a. A d. D b. B e. E c. C 2. The free-body diagram of a
More informationENGINEERING MECHANICS SOLUTIONS UNIT-I
LONG QUESTIONS ENGINEERING MECHANICS SOLUTIONS UNIT-I 1. A roller shown in Figure 1 is mass 150 Kg. What force P is necessary to start the roller over the block A? =90+25 =115 = 90+25.377 = 115.377 = 360-(115+115.377)
More informationHATZIC SECONDARY SCHOOL
HATZIC SECONDARY SCHOOL PROVINCIAL EXAMINATION ASSIGNMENT STATIC EQUILIBRIUM MULTIPLE CHOICE / 33 OPEN ENDED / 80 TOTAL / 113 NAME: 1. State the condition for translational equilibrium. A. ΣF = 0 B. ΣF
More informationPHYS 101 Previous Exam Problems. Force & Motion I
PHYS 101 Previous Exam Problems CHAPTER 5 Force & Motion I Newton s Laws Vertical motion Horizontal motion Mixed forces Contact forces Inclines General problems 1. A 5.0-kg block is lowered with a downward
More informationCalculating Truss Forces. Method of Joints
Calculating Truss Forces Method of Joints Forces Compression body being squeezed Tension body being stretched Truss truss is composed of slender members joined together at their end points. They are usually
More informationSOLUTION 8 7. To hold lever: a+ M O = 0; F B (0.15) - 5 = 0; F B = N. Require = N N B = N 0.3. Lever,
8 3. If the coefficient of static friction at is m s = 0.4 and the collar at is smooth so it only exerts a horizontal force on the pipe, determine the minimum distance x so that the bracket can support
More informationEquilibrium & Elasticity
PHYS 101 Previous Exam Problems CHAPTER 12 Equilibrium & Elasticity Static equilibrium Elasticity 1. A uniform steel bar of length 3.0 m and weight 20 N rests on two supports (A and B) at its ends. A block
More informationSECOND MIDTERM -- REVIEW PROBLEMS
Physics 10 Spring 009 George A. WIllaims SECOND MIDTERM -- REVIEW PROBLEMS A solution set is available on the course web page in pdf format. A data sheet is provided. No solutions for the following problems:
More informationSTATICS. Bodies. Vector Mechanics for Engineers: Statics VECTOR MECHANICS FOR ENGINEERS: Design of a support
4 Equilibrium CHAPTER VECTOR MECHANICS FOR ENGINEERS: STATICS Ferdinand P. Beer E. Russell Johnston, Jr. Lecture Notes: J. Walt Oler Texas Tech University of Rigid Bodies 2010 The McGraw-Hill Companies,
More informationASSOCIATE DEGREE IN ENGINEERING EXAMINATIONS SEMESTER /13
ASSOCIATE DEGREE IN ENGINEERING EXAMINATIONS SEMESTER 2 2012/13 COURSE NAME: ENGINEERING MECHANICS - STATICS CODE: ENG 2008 GROUP: AD ENG II DATE: May 2013 TIME: DURATION: 2 HOURS INSTRUCTIONS: 1. This
More informationIf the solution does not follow a logical thought process, it will be assumed in error.
Please review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam. If I detect cheating I will write a note on my exam and raise
More informationHowever, the friction forces are limited in magnitude and will not prevent motion if sufficiently large forces are applied.
FRICTION 1 Introduction In preceding chapters, it was assumed that surfaces in contact were either frictionless (surfaces could move freely with respect to each other) or rough (tangential forces prevent
More informationPHY131 Summer 2011 Class 5 Notes
PHY131 Summer 2011 Class 5 Notes 5/31/11 PHY131H1F Summer Class 5 Today: Equilibrium Mass, Weight, Gravity Friction, Drag Rolling without slipping Examples of Newton s Second Law Pre-class Reading Quiz.
More informationFRAMES AND MACHINES Learning Objectives 1). To evaluate the unknown reactions at the supports and the interaction forces at the connection points of a
FRAMES AND MACHINES Learning Objectives 1). To evaluate the unknown reactions at the supports and the interaction forces at the connection points of a rigid frame in equilibrium by solving the equations
More informationME Final Exam. PROBLEM NO. 4 Part A (2 points max.) M (x) y. z (neutral axis) beam cross-sec+on. 20 kip ft. 0.2 ft. 10 ft. 0.1 ft.
ME 323 - Final Exam Name December 15, 2015 Instructor (circle) PROEM NO. 4 Part A (2 points max.) Krousgrill 11:30AM-12:20PM Ghosh 2:30-3:20PM Gonzalez 12:30-1:20PM Zhao 4:30-5:20PM M (x) y 20 kip ft 0.2
More informationExam 3 PREP Chapters 6, 7, 8
PHY241 - General Physics I Dr. Carlson, Fall 2013 Prep Exam 3 PREP Chapters 6, 7, 8 Name TRUE/FALSE. Write 'T' if the statement is true and 'F' if the statement is false. 1) Astronauts in orbiting satellites
More information2. a) Explain the equilibrium of i) Concurrent force system, and ii) General force system.
Code No: R21031 R10 SET - 1 II B. Tech I Semester Supplementary Examinations Dec 2013 ENGINEERING MECHANICS (Com to ME, AE, AME, MM) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions
More information3D Force Couple System and Resultant. Q.No.1: Replace the force system by an equivalent force and couple moment at point A.
3D Force Couple System and Resultant Q.No.1: Replace the force system by an equivalent force and couple moment at point A. Q.No.2: Handle forces F1 and F2 are applied to the electric drill. Replace this
More informationPhysics Exam 2 October 11, 2007
INSTRUCTIONS: Write your NAME on the front of the blue exam booklet. The exam is closed book, and you may have only pens/pencils and a calculator (no stored equations or programs and no graphing). Show
More informationCHAPTER 2: EQUILIBRIUM OF RIGID BODIES
For a rigid body to be in equilibrium, the net force as well as the net moment about any arbitrary point O must be zero Summation of all external forces. Equilibrium: Sum of moments of all external forces.
More information1. The toggle pliers are used for a variety of clamping purposes. For the handle position given by a=10 o and for a handle grip P=150 N, calculate
1. The toggle pliers are used for a variet of clamping purposes. or the handle position given b a=10 o and for a handle grip P=150 N, calculate the clamping force C produced. Note that pins A and D are
More informationOverview. Dry Friction Wedges Flatbelts Screws Bearings Rolling Resistance
Friction Chapter 8 Overview Dry Friction Wedges Flatbelts Screws Bearings Rolling Resistance Dry Friction Friction is defined as a force of resistance acting on a body which prevents slipping of the body
More informationSTATICS. FE Review. Statics, Fourteenth Edition R.C. Hibbeler. Copyright 2016 by Pearson Education, Inc. All rights reserved.
STATICS FE Review 1. Resultants of force systems VECTOR OPERATIONS (Section 2.2) Scalar Multiplication and Division VECTOR ADDITION USING EITHER THE PARALLELOGRAM LAW OR TRIANGLE Parallelogram Law: Triangle
More informationIf the solution does not follow a logical thought process, it will be assumed in error.
Please indicate your group number (If applicable) Circle Your Instructor s Name and Section: MWF 8:30-9:20 AM Prof. Kai Ming Li MWF 2:30-3:20 PM Prof. Fabio Semperlotti MWF 9:30-10:20 AM Prof. Jim Jones
More informationEQUILIBRIUM OF RIGID BODIES
EQUILIBRIUM OF RIGID BODIES Equilibrium A body in equilibrium is at rest or can translate with constant velocity F = 0 M = 0 EQUILIBRIUM IN TWO DIMENSIONS Case where the force system acting on a rigid
More informationProblem d d d B C E D. 0.8d. Additional lecturebook examples 29 ME 323
Problem 9.1 Two beam segments, AC and CD, are connected together at C by a frictionless pin. Segment CD is cantilevered from a rigid support at D, and segment AC has a roller support at A. a) Determine
More informationIDE 110 Mechanics of Materials Spring 2006 Final Examination FOR GRADING ONLY
Spring 2006 Final Examination STUDENT S NAME (please print) STUDENT S SIGNATURE STUDENT NUMBER IDE 110 CLASS SECTION INSTRUCTOR S NAME Do not turn this page until instructed to start. Write your name on
More informationFinal Examination Study Set 1. (Solutions will be in the Solutions Manual of Textbook)
Final Examination Study Set 1 (Solutions will be in the Solutions Manual of Textbook) Final Examination Study Set 2 (Solutions will be in the Solutions Manual of Textbook) 3/86 The shaft, lever,
More informationMechatronics. MANE 4490 Fall 2002 Assignment # 1
Mechatronics MANE 4490 Fall 2002 Assignment # 1 1. For each of the physical models shown in Figure 1, derive the mathematical model (equation of motion). All displacements are measured from the static
More informationThe University of Melbourne Engineering Mechanics
The University of Melbourne 436-291 Engineering Mechanics Tutorial Eleven Instantaneous Centre and General Motion Part A (Introductory) 1. (Problem 5/93 from Meriam and Kraige - Dynamics) For the instant
More information5. Plane Kinetics of Rigid Bodies
5. Plane Kinetics of Rigid Bodies 5.1 Mass moments of inertia 5.2 General equations of motion 5.3 Translation 5.4 Fixed axis rotation 5.5 General plane motion 5.6 Work and energy relations 5.7 Impulse
More informationSpring 2018 Lecture 28 Exam Review
Statics - TAM 210 & TAM 211 Spring 2018 Lecture 28 Exam Review Announcements Concept Inventory: Ungraded assessment of course knowledge Extra credit: Complete #1 or #2 for 0.5 out of 100 pt of final grade
More informationLecture 14 February 16, 2018
Statics - TAM 210 & TAM 211 Lecture 14 February 16, 2018 SoonTrending.com Announcements Structured office hours of working through practice problems will be held during Sunday office hours, starting Sunday
More informationStatics: Lecture Notes for Sections
Chapter 6: Structural Analysis Today s Objectives: Students will be able to: a) Define a simple truss. b) Determine the forces in members of a simple truss. c) Identify zero-force members. READING QUIZ
More information