ANSYS AIM Tutorial Modeling Forces in Permanent Magnets
|
|
- Geoffrey Lang
- 5 years ago
- Views:
Transcription
1 ANSYS AIM Tutorial Modeling Forces in Permanent Magnets Author(s):Joshua Wallace Created using ANSYS AIM 18.2 Problem Specification Pre-Analysis & Start Up Governing Equation Start Up Geometry Physics Set-Up Specify Material Boundary Conditions / Forces Solution/Result Verification
2 Problem Specification This problem is intended to address the questions of force calculations as well as modeling of permanent magnets in axisymmetric and three dimensional geometries.the spool is made out of brass, the coil is made out of copper and the magnet is made of NdFe30. In this demonstration two cases will be considered and the force between the magnet and the coil will be determined. f = f(i, R, s ) f = f orce between magnet and coil i = c urrent, R = h orizontal displacement s = v ertical displacement I n case one, both s = 0 and R = 0.254mm are held constant. T herefore, f = f (i) I n case two, s = 0 mm and i = 50mA are kept constant. T herefore f = f (R)
3 In the first case the current will vary from from 0-100mA in 10mA intervals. In case two the axial displacement will vary from mm in.05mm intervals.
4 Pre-Analysis & Start Up Governing Equation Magnetostatics is the study of magnetic fields in devices where the magnetic field is generated from DC (steady) currents and/or permanent magnets. Magnetostatics is a special case of Maxwell s equations, which form the basis of electromagnetism. For magnetostatics the electric field inside of a current carrying coil is completely decoupled from the magnetic field, and the following Maxwell s equations are solved for magnetostatics - Where denotes divergence, H is the magnetic field intensity, J is the current density and B is the magnetic flux density.
5 Start Up A few words on the formatting on the following instructions: 1) Notes that require you to perform an action are colored in blue 2) General information will be colored in black, but do not require any action 3) Words that are bolded are labels for items found in ANSYS AIM 4) Most important notes will be colored in red Now that the the pre-calculations are finished, we are ready to begin the simulation in ANSYS AIM. Open ANSYS AIM by going to Start > All Apps > ANSYS 18.2 > ANSYS AIM Once starting page has opened, select the Magnetics template as shown below.
6 Geometry You will be prompted to either Define new geometry, Import geometry file, or connect to active CAD session. Select import new geometry and downloaded the file here. AIM will prompt again asking to select your calculation type, physics coupling and options. Under options, check compute force and then click Finish. Creating geometric parameters In order to vary the horizontal distance between the coil and magnet a parameter must be created. Once AIM has loaded click on Geometry > Edit Geometry. Hide the enclosure by deselecting the checkmark.
7 Triple click on the magnet to select the body. Select the move tool and click on the origin. Drag the origin onto the face of the magnet closest to the spool.
8 Once the origin turns into a square, select the blue axis of the Move tool. The other axis will be greyed out and in the General sidebar select the Ruler tool. The Ruler tool will then follow the cursor, at which point click the face of the spool closest to the inside the gap.
9 To create the parameter click on the P next to the highlighted dimension box. Once the parameter is created, click the x in the top right corner to begin the physics set up. ANSYS Inc.
10 Physics Set-Up AIM will automatically create an enclosure around the geometry. In order to see the inside geometry click on Physics > click on the box > right click on the box > Hide Body. Specify Material Click on Add, next to Material Assignments > Material Assignment > Copper (Material Samples). Next, click on body selection in top right corner. Select the coil and click Add. This assigns copper to the coil.
11 Then click on next step and repeat the process. Assign NdFe30 to the magnet and brass to the spool. (You can use Type to Search to find NdFe30 and Brass in the material library.)
12 Boundary Conditions / Forces Now force computation must be set up. Click Next Step > Fix > Force Computation. Select the magnet using body select and click the +. Leave all other setting in default condition. Since a current is running through the copper coil, a current condition will need to be created. Right click > Add > Electromagnetic Conditions > Current. Select the surface by looking for the line in the line that runs perpendicular to the spool face.. Click on the plane below the line by using the plane selector. Then input a Current of.01 amps and 280 for the Number of Conductors. Click on the arrow below to parameterize the Operating current.
13 Then click on Generate Conduction Paths, this will show the solver interpretation of the coil. If the solver s interpretation of the coil is incorrect (current is flowing outside of the coil) insulating boundary conditions must be added to ensure that the current stays within the coil. Since the solvers interpretation of the coil is incorrect (current is also flowing in the brass spool), insulated boundary conditions will be added.
14 Right click > Add > Electromagnetic Conditions > Insulating. Click on the three inside faces of the brass spool. Hiding the coil geometry will make this step easier.
15 In order to check that insulating condition worked, click on Physics > Electromagnetic Conditions > Current 1 > Generate Conduction Paths. ANSYS Inc.
16 The solvers new interpretation of the coil is correct. Case one will now be set up. ANSYS Inc.
17 Setting up case 1: The last parameter we need to define is the force on the magnet. Go to Results in the workflow. Under Objects, click on results again. Select Value Force Magnitude 1. Click on the arrow horizontal from undefined and select parametrize. Click on the design points dashboard in the upper right hand corner. The first table that comes up is the design points. Under Current 1 Operating current, iterate the input by 10 ma up to 100mA. Use the image below for reference. In the other column, input.254mm for the horizontal(r) distance. Once this is done, click Update All in the top right corner of the design points dashboard. AIM will solve each case for the force on the magnet and the force outputs for each current input can be seen in the design points dashboard.
18 Setting up case 2: In case two, the force of the magnetic is a function of horizontal(r) distance. In the design parameters dashpoint, change all the current data points to 50mA. Then iterate the horizontal data points from 0.05mm-.5mm by 0.05mm. Click update all to see results.
19 Solution/Result Click on Results in the Workflow and add a vector plot. Choose Magnetic Flux Density for the variable and click Evaluate. The results are shown below.
20 Verification ANSYS Inc.
1 Solution of Electrostatics Problems with COM- SOL
1 Solution of Electrostatics Problems with COM- SOL This section gives examples demonstrating how Comsol can be used to solve some simple electrostatics problems. 1.1 Laplace s Equation We start with a
More informationMotor-CAD combined electromagnetic and thermal model (January 2015)
Motor-CAD combined electromagnetic and thermal model (January 2015) Description The Motor-CAD allows the machine performance, losses and temperatures to be calculated for a BPM machine. In this tutorial
More informationComparing whole genomes
BioNumerics Tutorial: Comparing whole genomes 1 Aim The Chromosome Comparison window in BioNumerics has been designed for large-scale comparison of sequences of unlimited length. In this tutorial you will
More informationWhat Is a Solution to a System?
Math Objectives Students will understand what it means for an ordered pair to be a solution to a linear equation. Students will understand what it means for an ordered pair to be a solution to a system
More informationThis tutorial is intended to familiarize you with the Geomatica Toolbar and describe the basics of viewing data using Geomatica Focus.
PCI GEOMATICS GEOMATICA QUICKSTART 1. Introduction This tutorial is intended to familiarize you with the Geomatica Toolbar and describe the basics of viewing data using Geomatica Focus. All data used in
More informationBiot-Savart Law Performing various measures to study the magnetic field intensity variations around an inducting coil
field intensity variations around an inducting coil Objective The goal of the activity is to investigate the surroundings of an isolated copper coil, fed with a low voltage direct current source. Using
More informationVERSION 4.4. Introduction to AC/DC Module
VERSION 4.4 Introduction to AC/DC Module Introduction to the AC/DC Module 1998 2013 COMSOL Protected by U.S. Patents 7,519,518; 7,596,474; 7,623,991; and 8,457,932. Patents pending. This Documentation
More informationMultiphysics Modeling
11 Multiphysics Modeling This chapter covers the use of FEMLAB for multiphysics modeling and coupled-field analyses. It first describes the various ways of building multiphysics models. Then a step-by-step
More informationMedical Physics & Science Applications
Power Conversion & Electromechanical Devices Medical Physics & Science Applications Transportation Power Systems 1-5: Introduction to the Finite Element Method Introduction Finite Element Method is used
More informationCAD package for electromagnetic and thermal analysis using finite elements. Flux. by CEDRAT. Magneto Static application tutorial.
CAD package for electromagnetic and thermal analysis using finite elements Flux by CEDRAT Magneto Static application tutorial 2D basic example Flux is a registered trademark. Flux software : COPYRIGHT
More informationCoupling Physics. Tomasz Stelmach Senior Application Engineer
Coupling Physics Tomasz Stelmach Senior Application Engineer Agenda Brief look @ Multiphysics solution What is new in R18 Fluent Maxwell coupling wireless power transfer Brief look @ ANSYS Multiphysics
More informationMagnetic Field Analysis
NISA - EMAG EMAG is the electromagnetic module of the family of general purpose finite element based program NISA. It can determine electric and magnetic field distributions in a wide class of electromagnetic
More informationLecture 9 Thermal Analysis
Lecture 9 Thermal Analysis 16.0 Release Introduction to ANSYS Mechanical 1 2015 ANSYS, Inc. February 27, 2015 Chapter Overview In this chapter, performing steady-state thermal analyses in Mechanical will
More informationISIS/Draw "Quick Start"
ISIS/Draw "Quick Start" Click to print, or click Drawing Molecules * Basic Strategy 5.1 * Drawing Structures with Template tools and template pages 5.2 * Drawing bonds and chains 5.3 * Drawing atoms 5.4
More information41. Sim Reactions Example
HSC Chemistry 7.0 41-1(6) 41. Sim Reactions Example Figure 1: Sim Reactions Example, Run mode view after calculations. General This example contains instruction how to create a simple model. The example
More informationA Simple Weak-Field Coupling Benchmark Test of the Electromagnetic-Thermal-Structural Solution Capabilities of LS-DYNA Using Parallel Current Wires
13 th International LS-DYNA Users Conference Session: Electromagnetic A Simple Weak-Field Coupling Benchmark Test of the Electromagnetic-Thermal-Structural Solution Capabilities of LS-DYNA Using Parallel
More informationMcIDAS-V Tutorial Displaying Point Observations from ADDE Datasets updated July 2016 (software version 1.6)
McIDAS-V Tutorial Displaying Point Observations from ADDE Datasets updated July 2016 (software version 1.6) McIDAS-V is a free, open source, visualization and data analysis software package that is the
More informationProject 1: Analysis of an induction machine using a FEM based software EJ Design of Electrical Machines
Project : Analysis of an induction machine using a FEM based software General instructions In this assignment we will analyze an induction machine using Matlab and the freely available finite element software
More informationOperation of an Electromagnetic Trigger with a Short-circuit Ring
Operation of an Electromagnetic Trigger with a Short-circuit Ring Dejan Križaj 1*, Zumret Topčagić 1, and Borut Drnovšek 1,2 1 Faculty of Electrical Engineering, University of Ljubljana, Ljubljana, Slovenia,
More informationElectric Fields and Equipotentials
OBJECTIVE Electric Fields and Equipotentials To study and describe the two-dimensional electric field. To map the location of the equipotential surfaces around charged electrodes. To study the relationship
More informationLua, Boundary Conditions and ect..
Lua, Boundary Conditions and ect.. Some further informations about calculating in Femm M. Rad 10.03.2017 Outline Lua scripting Border conditions About torque and force calculation in Femm Lua scripts To
More informationElectric Field PHYS 296
Electric Field PHYS 296 Your name Lab section PRE-LAB QUIZZES 1. What will we investigate in this lab? 2. In a uniform electric field between two parallel plates, a potential probe records the electric
More informationChapter 12. Magnetism and Electromagnetism
Chapter 12 Magnetism and Electromagnetism 167 168 AP Physics Multiple Choice Practice Magnetism and Electromagnetism SECTION A Magnetostatics 1. Four infinitely long wires are arranged as shown in the
More informationAn area chart emphasizes the trend of each value over time. An area chart also shows the relationship of parts to a whole.
Excel 2003 Creating a Chart Introduction Page 1 By the end of this lesson, learners should be able to: Identify the parts of a chart Identify different types of charts Create an Embedded Chart Create a
More informationElectromagnetic Forces on Parallel Current-
Page 1 of 5 Tutorial Models : Electromagnetic Forces on Parallel Current-Carrying Wires Electromagnetic Forces on Parallel Current- Carrying Wires Introduction One ampere is defined as the constant current
More informationExercises for Windows
Exercises for Windows CAChe User Interface for Windows Select tool Application window Document window (workspace) Style bar Tool palette Select entire molecule Select Similar Group Select Atom tool Rotate
More informationCrossing Pipes Discussion
Crossing Pipes Discussion Draft 2, 9/21/06 Chapter 7 of [4] outlines a steady state thermal analysis of an assumed pipeline junction. Here alternate points of view and additional post-processing features
More informationSpace Objects. Section. When you finish this section, you should understand the following:
GOLDMC02_132283433X 8/24/06 2:21 PM Page 97 Section 2 Space Objects When you finish this section, you should understand the following: How to create a 2D Space Object and label it with a Space Tag. How
More informationChart Group indicator
Chart Group indicator 1. Overview... 2 2. Using the... 3 2.1 Adding the indicator to a chart... 3 2.2 Choosing whether to link the timeframe or the symbol... 3 2.3 Assigning charts to groups... 3 2.3.1
More informationSTAR-CCM+ and SPEED for electric machine cooling analysis
STAR-CCM+ and SPEED for electric machine cooling analysis Dr. Markus Anders, Dr. Stefan Holst, CD-adapco Abstract: This paper shows how two well established software programs can be used to determine the
More informationApplication Note. U. Heat of Formation of Ethyl Alcohol and Dimethyl Ether. Introduction
Application Note U. Introduction The molecular builder (Molecular Builder) is part of the MEDEA standard suite of building tools. This tutorial provides an overview of the Molecular Builder s basic functionality.
More informationComputer simulation of radioactive decay
Computer simulation of radioactive decay y now you should have worked your way through the introduction to Maple, as well as the introduction to data analysis using Excel Now we will explore radioactive
More informationv Prerequisite Tutorials GSSHA WMS Basics Watershed Delineation using DEMs and 2D Grid Generation Time minutes
v. 10.1 WMS 10.1 Tutorial GSSHA WMS Basics Creating Feature Objects and Mapping Attributes to the 2D Grid Populate hydrologic parameters in a GSSHA model using land use and soil data Objectives This tutorial
More informationAn ion follows a circular path in a uniform magnetic field. Which single change decreases the radius of the path?
T5-1 [237 marks] 1. A circuit is formed by connecting a resistor between the terminals of a battery of electromotive force (emf) 6 V. The battery has internal resistance. Which statement is correct when
More informationTutorial: Theory and applications of the Maxwell stress tensor
Tutorial: Theory and applications of the Maxwell stress tensor Stanley Humphries, Copyright 2012 Field Precision PO Box 13595, Albuquerque, NM 87192 U.S.A. Telephone: +1-505-220-3975 Fax: +1-617-752-9077
More informationProblem info Geometry model Labelled Objects Results Nonlinear dependencies
Problem info Problem type: Transient Magnetics (integration time: 9.99999993922529E-09 s.) Geometry model class: Plane-Parallel Problem database file names: Problem: circuit.pbm Geometry: Circuit.mod Material
More informationncounter PlexSet Data Analysis Guidelines
ncounter PlexSet Data Analysis Guidelines NanoString Technologies, Inc. 530 airview Ave North Seattle, Washington 98109 USA Telephone: 206.378.6266 888.358.6266 E-mail: info@nanostring.com Molecules That
More informationVersion The diagram below represents lines of magnetic flux within a region of space.
1. The diagram below represents lines of magnetic flux within a region of space. 5. The diagram below shows an electromagnet made from a nail, a coil of insulated wire, and a battery. The magnetic field
More informationLab 1: Dynamic Simulation Using Simulink and Matlab
Lab 1: Dynamic Simulation Using Simulink and Matlab Objectives In this lab you will learn how to use a program called Simulink to simulate dynamic systems. Simulink runs under Matlab and uses block diagrams
More informationModelling the Electrical Parameters Of A Loudspeaker Motor System With The AC-DC Module (MEPLMSAM)
Modelling the Electrical Parameters Of A Loudspeaker Motor System With The AC-DC Module (MEPLMSAM) M. Cobianchi *1,Dr. M. Rousseau *1 and S. Xavier* 1 1 B&W Group Ltd, Worthing, West Sussex, England. *Corresponding
More informationSuperCELL Data Programmer and ACTiSys IR Programmer User s Guide
SuperCELL Data Programmer and ACTiSys IR Programmer User s Guide This page is intentionally left blank. SuperCELL Data Programmer and ACTiSys IR Programmer User s Guide The ACTiSys IR Programmer and SuperCELL
More informationIntegrated Square-Shaped Spiral Inductor
Page 1 of 9 Electrical Component Models : Integrated Square-Shaped Spiral Inductor Integrated Square-Shaped Spiral Inductor This example presents a model of a micro-scale square inductor, used for LC bandpass
More informationNMR Predictor. Introduction
NMR Predictor This manual gives a walk-through on how to use the NMR Predictor: Introduction NMR Predictor QuickHelp NMR Predictor Overview Chemical features GUI features Usage Menu system File menu Edit
More informationAnsoft HFSS 3D Boundary Manager Sources
Lumped Gap Defining s Voltage and Current When you select Source, you may choose from the following source types: Incident wave Voltage drop Current Magnetic bias These sources are available only for driven
More informationElectromagnetics in COMSOL Multiphysics is extended by add-on Modules
AC/DC Module Electromagnetics in COMSOL Multiphysics is extended by add-on Modules 1) Start Here 2) Add Modules based upon your needs 3) Additional Modules extend the physics you can address 4) Interface
More informationWatershed Modeling Orange County Hydrology Using GIS Data
v. 10.0 WMS 10.0 Tutorial Watershed Modeling Orange County Hydrology Using GIS Data Learn how to delineate sub-basins and compute soil losses for Orange County (California) hydrologic modeling Objectives
More informationStudent Activity Sheet- Denali Topo Map
Student Activity Sheet- Denali Topo Map Directions: Follow the steps in order and answer the associated questions as you proceed through the activity. The first part of the activity will be guided by your
More informationNR/RR. Set No. 2 CODE NO: NR/RR210204
Set No. 2 II B.Tech I Semester Examinations,May 2011 ELECTROMAGNETIC FIELDS Electrical And Electronics Engineering Time: 3 hours Max Marks: 80 Answer any FIVE Questions All Questions carry equal marks
More informationSection 26.1: Reporting Conventions. Section 26.2: Fluxes Through Boundaries. Section 26.3: Forces on Boundaries
Chapter 26. Alphanumeric Reporting FLUENT provides tools for computing and reporting integral quantities at surfaces and boundaries. These tools enable you to find the mass flow rate and heat transfer
More informationStudying Topography, Orographic Rainfall, and Ecosystems (STORE)
Studying Topography, Orographic Rainfall, and Ecosystems (STORE) Introduction Basic Lesson 3: Using Microsoft Excel to Analyze Weather Data: Topography and Temperature This lesson uses NCDC data to compare
More informationOneStop Map Viewer Navigation
OneStop Map Viewer Navigation» Intended User: Industry Map Viewer users Overview The OneStop Map Viewer is an interactive map tool that helps you find and view information associated with energy development,
More informationThermal Analysis & Design Improvement of an Internal Air-Cooled Electric Machine Dr. James R. Dorris Application Specialist, CD-adapco
Thermal Analysis & Design Improvement of an Internal Air-Cooled Electric Machine Dr. James R. Dorris Application Specialist, CD-adapco Thermal Analysis of Electric Machines Motivation Thermal challenges
More informationTwo problems to be solved. Example Use of SITATION. Here is the main menu. First step. Now. To load the data.
Two problems to be solved Example Use of SITATION Mark S. Daskin Department of IE/MS Northwestern U. Evanston, IL 1. Minimize the demand weighted total distance (or average distance) Using 10 facilities
More informationComputational Chemistry Lab Module: Conformational Analysis of Alkanes
Introduction Computational Chemistry Lab Module: Conformational Analysis of Alkanes In this experiment, we will use CAChe software package to model the conformations of butane, 2-methylbutane, and substituted
More informationGeography 281 Map Making with GIS Project Four: Comparing Classification Methods
Geography 281 Map Making with GIS Project Four: Comparing Classification Methods Thematic maps commonly deal with either of two kinds of data: Qualitative Data showing differences in kind or type (e.g.,
More informationDifferent Techniques for Calculating Apparent and Incremental Inductances using Finite Element Method
Different Techniques for Calculating Apparent and Incremental Inductances using Finite Element Method Dr. Amer Mejbel Ali Electrical Engineering Department Al-Mustansiriyah University Baghdad, Iraq amerman67@yahoo.com
More informationCHAPTER 5 ELECTROMAGNETIC INDUCTION
CHAPTER 5 ELECTROMAGNETIC INDUCTION 1 Quick Summary on Previous Concepts Electrostatics Magnetostatics Electromagnetic Induction 2 Cases of Changing Magnetic Field Changing Field Strength in a Loop A Loop
More informationCHEMDRAW ULTRA ITEC107 - Introduction to Computing for Pharmacy. ITEC107 - Introduction to Computing for Pharmacy 1
CHEMDRAW ULTRA 12.0 ITEC107 - Introduction to Computing for Pharmacy 1 Objectives Basic drawing skills with ChemDraw Bonds, captions, hotkeys, chains, arrows Checking and cleaning up structures Chemical
More informationPhysicsAndMathsTutor.com 1
PhysicsndMathsTutor.com 1 Q1. Which line, to, correctly describes the trajectory of charged particles which enter, at right angles, (a) a uniform electric field, and (b) a uniform magnetic field? (a) uniform
More informationlet s examine pupation rates. With the conclusion of that data collection, we will go on to explore the rate at which new adults appear, a process
Population Dynamics and Initial Population Size (Module website: http://web.as.uky.edu/biology/faculty/cooper/population%20dynamics%20examples%20 with%20fruit%20flies/theamericanbiologyteacher-populationdynamicswebpage.html
More informationIntroduction to Hartree-Fock calculations in Spartan
EE5 in 2008 Hannes Jónsson Introduction to Hartree-Fock calculations in Spartan In this exercise, you will get to use state of the art software for carrying out calculations of wavefunctions for molecues,
More informationInvestigation 5: What happens when plates move sideways past each other?
Tectonics Investigation 5: Teacher Guide Investigation 5: What happens when plates move sideways past each other? Plates move sideways past each other at transform boundaries. At these boundaries, the
More informationv WMS Tutorials GIS Module Importing, displaying, and converting shapefiles Required Components Time minutes
v. 11.0 WMS 11.0 Tutorial Importing, displaying, and converting shapefiles Objectives This tutorial demonstrates how to import GIS data, visualize it, and convert it into WMS coverage data that could be
More informationOcean Optics Red Tide UV-VIS Spectrometer (Order Code: SPRT-UV-VIS)
Ocean Optics Red Tide UV-VIS Spectrometer (Order Code: SPRT-UV-VIS) The UV-VIS spectrometer is a portable ultraviolet light and visible light spectrophotometer, combining a spectrometer and a light source/cuvette
More informationDevelopment of a Compressor for a Miniature Pulse Tube Cryocooler of 2.5 W at 65 K
Development of a Compressor for a Miniature Pulse Tube Cryocooler of 2.5 W at 65 K N. Matsumoto, Y. Yasukawa, K. Ohshima, T. Takeuchi, K. Yoshizawa, T. Matsushita, Y. Mizoguchi, and A. Ikura Fuji Electric
More informationSeeSAR 7.1 Beginners Guide. June 2017
SeeSAR 7.1 Beginners Guide June 2017 Part 1: Basics 1 Type a pdb code and press return or Load your own protein or already existing project, or Just load molecules To begin, let s type 2zff and download
More informationEE 410/510: Electromechanical Systems Chapter 4
EE 410/510: Electromechanical Systems Chapter 4 Chapter 4. Direct Current Electric Machines and Motion Devices Permanent Magnet DC Electric Machines Radial Topology Simulation and Experimental Studies
More informationCable Tension APPENDIX D. Objectives: Demonstrate the use of elastic-plastic material properties. Create an enforced displacement on the model.
APPENDIX D Cable Tension Objectives: Demonstrate the use of elastic-plastic material properties. Create an enforced displacement on the model. Run an MSC.Nastran nonlinear static analysis. Create an accurate
More informationYou will return this handout to the instructor at the end of the lab period. Experimental verification of Ampere s Law.
PHY222 LAB 6 AMPERE S LAW Print Your Name Print Your Partners' Names Instructions Read section A prior to attending your lab section. You will return this handout to the instructor at the end of the lab
More informationDate: Summer Stem Section:
Page 1 of 7 Name: Date: Summer Stem Section: Summer assignment: Build a Molecule Computer Simulation Learning Goals: 1. Students can describe the difference between a molecule name and chemical formula.
More informationVersion 1.2 October 2017 CSD v5.39
Mogul Geometry Check Table of Contents Introduction... 2 Example 1. Using Mogul to assess intramolecular geometry... 3 Example 2. Using Mogul to explain activity data... 5 Conclusions... 8 Further Exercises...
More information1-1: Introduction to the Opera-3d software
Power Conversion & Electromechanical Devices Medical Physics & Science Applications Transportation Power Systems 1-1: Introduction to the Opera-3d software OPERA-3d What is OPERA-3d? Structure of the package
More informationTracking. Particle In Cell. Wakefield
CST PARTICLE STUDIO STUDIO SOLVERS & APPLICATIONS 1 www.cst.com Mar-09 CST PARTICLE STUDIO Solvers Tracking Simulation of DC Particle Guns, Collectors, Magnets Tracking in static E/H fields (incl. space
More informationLevitation by Using Electromagnetic Force
Levitation by Using Electromagnetic Force Mireia Colom Guerra (University of Barcelona), Marc Serra Peralta (Autonomous University of Barcelona), Dalibor Danilovic (Ivanjica Gymnasium). ABSTRACT: In the
More informationCreate Satellite Image, Draw Maps
Create Satellite Image, Draw Maps 1. The goal Using Google Earth, we want to create and import a background file into our Adviser program. From there, we will be creating paddock boundaries. The accuracy
More informationDimerization in a Tubular Reactor
Dimerization in a Tubular Reactor Tubular reactors are very common in large-scale continuous, for example in the petroleum industry. One key design and optimization parameter is the conversion, that is
More informationhp calculators HP 48GII Solving for roots of polynomials and quadratics The Numeric Solver Practice finding roots of polynomials and quadratics
The Numeric Solver Practice finding roots of polynomials and quadratics The Numeric Solver The HP 48GII has a numeric solver that can find the solutions to many different types of problems. It is invoked
More informationES205 Analysis and Design of Engineering Systems: Lab 1: An Introductory Tutorial: Getting Started with SIMULINK
ES205 Analysis and Design of Engineering Systems: Lab 1: An Introductory Tutorial: Getting Started with SIMULINK What is SIMULINK? SIMULINK is a software package for modeling, simulating, and analyzing
More informationComputational Study of Chemical Kinetics (GIDES)
Computational Study of Chemical Kinetics (GIDES) Software Introduction Berkeley Madonna (http://www.berkeleymadonna.com) is a dynamic modeling program in which relational diagrams are created using a graphical
More informationShape, Convection and Convergence
Presented at the COMSOL Conference 2008 Boston Shape, Convection and Convergence,VP Research, Inc. Who is? Who is? We are: A Technical Consultation firm in business since 1993 Who is? We are: A Technical
More informationStoichiometric Reactor Simulation Robert P. Hesketh and Concetta LaMarca Chemical Engineering, Rowan University (Revised 4/8/09)
Stoichiometric Reactor Simulation Robert P. Hesketh and Concetta LaMarca Chemical Engineering, Rowan University (Revised 4/8/09) In this session you will learn how to create a stoichiometric reactor model
More informationCurriculum Support Maps for the Study of Indiana Coal (Student Handout)
Curriculum Support Maps for the Study of Indiana Coal (Student Handout) Introduction In this lesson you will learn how to use a geographic information system (GIS) program (IndianaMap) to investigate coal
More informationMAGNETIC PROBLEMS. (d) Sketch B as a function of d clearly showing the value for maximum value of B.
PHYS2012/2912 MAGNETC PROBLEMS M014 You can investigate the behaviour of a toroidal (dough nut shape) electromagnet by changing the core material (magnetic susceptibility m ) and the length d of the air
More informationThe CSC Interface to Sky in Google Earth
The CSC Interface to Sky in Google Earth CSC Threads The CSC Interface to Sky in Google Earth 1 Table of Contents The CSC Interface to Sky in Google Earth - CSC Introduction How to access CSC data with
More informationLeaf Spring (Material, Contact, geometric nonlinearity)
00 Summary Summary Nonlinear Static Analysis - Unit: N, mm - Geometric model: Leaf Spring.x_t Leaf Spring (Material, Contact, geometric nonlinearity) Nonlinear Material configuration - Stress - Strain
More informationICM-Chemist-Pro How-To Guide. Version 3.6-1h Last Updated 12/29/2009
ICM-Chemist-Pro How-To Guide Version 3.6-1h Last Updated 12/29/2009 ICM-Chemist-Pro ICM 3D LIGAND EDITOR: SETUP 1. Read in a ligand molecule or PDB file. How to setup the ligand in the ICM 3D Ligand Editor.
More informationC. Incorrect! Use the formula for magnetic flux. This is the product of magnetic field, times area, times the angle between them.
AP Physics - Problem Drill 17: Electromagnetism Instruction: (1) Read the problem statement and answer choices carefully (2) Work the problems on paper as 1. A house has a wall that has an area of 28 m
More informationMolecular Modeling and Conformational Analysis with PC Spartan
Molecular Modeling and Conformational Analysis with PC Spartan Introduction Molecular modeling can be done in a variety of ways, from using simple hand-held models to doing sophisticated calculations on
More informationPanosFX CALENDAR User guide. PanosFX CALENDAR. For Adobe Photoshop CC, CS6, CS5, CS4, CS3. PSD templates & language switcher actions.
PanosFX CALENDAR For Adobe Photoshop CC, CS6, CS5, CS4, CS3 PSD templates & language switcher actions User Guide CONTENTS 1. THE BASICS... 1 1.1. Description... 1 1.2. How the files are organized... 2
More informationThe Nottingham eprints service makes this work by researchers of the University of Nottingham available open access under the following conditions.
Arumugam, Puvaneswaran and Dusek, Jiri and Mezani, Smail and Hamiti, Tahar and Gerada, C. (2015) Modeling and analysis of eddy current losses in permanent magnet machines with multi-stranded bundle conductors.
More informationWelcome A STUDY ON UNIFORMITY OF A MAGNET. Excerpt from the Proceedings of the 2014 COMSOL Conference in Bangalore
Welcome A STUDY ON UNIFORMITY OF A MAGNET What is the presentation all about?? The presentation deals with the project conducted at Variable Energy Cyclotron Centre Kolkata Aim of the Project: To Design
More informationScienceWord and PagePlayer Chemical formulae. Dr Emile C. B. COMLAN Novoasoft Representative in Africa
ScienceWord and PagePlayer Chemical formulae Dr Emile C. B. CMLAN Novoasoft Representative in Africa Emails: ecomlan@yahoo.com ecomlan@scienceoffice.com Web site: www.scienceoffice.com Chemical formulae
More informationBuilding Inflation Tables and CER Libraries
Building Inflation Tables and CER Libraries January 2007 Presented by James K. Johnson Tecolote Research, Inc. Copyright Tecolote Research, Inc. September 2006 Abstract Building Inflation Tables and CER
More informationX ; this can also be expressed as
The Geometric Mean ID: 9466 TImath.com Time required 30 minutes Activity Overview In this activity, students will establish that several triangles are similar and then determine that the altitude to the
More information4 Finite Element Analysis of a three-phase PM synchronous machine
Assignment 4 1-1 4 Finite Element Analysis of a three-phase PM synchronous machine The goal of the third assignment is to extend your understanding on electromagnetic analysis in FEM. This assignment is
More informationStandards-Based Quantification in DTSA-II Part II
Standards-Based Quantification in DTSA-II Part II Nicholas W.M. Ritchie National Institute of Standards and Technology, Gaithersburg, MD 20899-8371 nicholas.ritchie@nist.gov Introduction This article is
More informationExample Resistive Heating
Example Resistive Heating SOLVED WITH COMSOL MULTIPHYSICS 3.5a COPYRIGHT 2008. All right reserved. No part of this documentation may be photocopied or reproduced in any form without prior written consent
More informationUsing the Budget Features in Quicken 2008
Using the Budget Features in Quicken 2008 Quicken budgets can be used to summarize expected income and expenses for planning purposes. The budget can later be used in comparisons to actual income and expenses
More informationCarbon Structure Simulations using Crystal Viewer Tool
Carbon Structure Simulations using Crystal Viewer Tool The Crystal Viewer tool in nanohub.org can be used to build three carbon nanostructures: graphene sheets, Buckminsterfullerene, Bucky balls (C 60
More informationElectricity. Measuring the force on current-carrying conductors in a homogeneous magnetic field. LEYBOLD Physics Leaflets P
Electricity Magnetostatics The effects of force in a magnetic field LEYBOLD Physics Leaflets Measuring the force on current-carrying conductors in a homogeneous magnetic field Recording with CASSY Objects
More information