Mechanical Models for Asphalt Behavior and Performance
|
|
- Beatrix Terry
- 6 years ago
- Views:
Transcription
1 Mechanical Models for Asphalt Behavior and Performance Introduction and Review of Linear Viscoelastic Behaviors
2 About the webinar series Past, current, and future plan for webinar series Introduction to the building blocks of mechanistic models (October 18, 212) Overview of approaches to modeling damage in asphalt materials and pavements (December 11, 212) Viscoelastic models to unify asphalt stiffness measures (this webinar) Exemplify the use of models to characterize cracking, rutting, moisture damage, etc. (future)
3 About the webinar series The focus of these webinars is to: review the basic terms associated with mechanistic models so that the end users may effectively use these models, better appreciate the advantages of using mechanical models, develop a broader understanding of how mechanistic models work, and exemplify the use of models to solve specific problems faced by the asphalt materials and pavements community.
4 About the webinar series The webinars are not intended to: demonstrate the theoretical development of a model or models, or present the mathematical development of different models. AFK5(1) fall workshop series 213 Viscoplasticity (Dr. Charles Schwartz (UMD) and Dr. Regis Carvalho, Oaken Consult) 214 Viscoelastic Continuum Damage Model (Dr. Richard Kim, NCSU and Dr. Shane Underwood, ASU)
5 About this webinar 1. Review of linear viscoelastic behaviors 2. Application of linear viscoelastic models for laboratory evaluations 3. Application of linear viscoelastic models for field evaluations Shane Underwood, Ph.D. ASU Emin Kutay, Ph.D. MSU
6 Application of Linear Viscoelastic Models for Field Evaluations
7 Learning Objectives Understand the role of viscoelastic relaxation on in-situ stress-strain response of asphalt pavements. Explain how Falling Weight Deflectometer should be run and what data should be collected in order to be able to backcalculate in-situ E* mastercurve.
8 Strain response in the field ε y ε z z x y ε z ε y ε x Layered Viscoelastic Moving Load Model (LAVAM)
9 Elastic vs. Viscoelastic assumption in the field Transverse Microstrain z=3.99", y=1",x=", (-): Compr., (+): Tens. Viscoelastic relaxation Measured-1 Measured-2 Predicted - LAVA Predicted - Layered elastic time
10 Elastic vs. Viscoelastic assumption in the field Longitudinal Microstrain 4 2 z=3.99", x=", (-): Compr., (+): Tens. Elastic Viscoelastic time Transverse Microstrain Vertical Microstrain z=3.99", x=", (-): Compr., (+): Tens. Elastic Viscoelastic time z=3.99", x=", (-): Compr., (+): Tens Elastic Viscoelastic time
11 What is different? Elastic vs Viscoelastic assumption. Elastic stress-strain relationship: σ() t = Eε() t Viscoelastic stress-strain relationship: t dε σ() t = Et ( τ) dτ dτ
12 Viscoelastic properties E* or D* E(t) D(t) E* D* E(t) D(t) Freq(Hz) Time(s) 1-5 Sigmoid functions: ( ) = c 1 + log E(t) c 2 1+ exp( c 3 c 4 log(t R )) 7
13 E* Master curve (a) log( E* ) (psi) T = -1 o C T = 4 o C T = 21 o C T = 37 o C log( f ) (Hz)
14 E* Master curve Time Temperature Superposition Principle Shift data horizontally to develop a single master curve (b) log( E* ) (psi) T = -1 o C T = 4 o C T = 21 o C T = 37 o C log ( E* ) = b exp(-b 3 b 2 b 4 log( f R )) f R = f a(t ) Reduced Frequency, log(f R ) (Hz)
15 In-situ E* mastercurve Falling Weight Deflectometer (FWD) test FWD test? E* Mastercurve
16 E* backcalculation approach General Steps: Deflection (in) Measured u(t) field Time(seconds) Deflection (in) Predicted u(t) from FWD simulation Time(seconds) Minimize Error = m 1 n ( k k u ) i uo ( k u ) k = 1 i, o= 1 i max 11
17 Layered Viscoelastic (forward) Algorithm (LAVA) Response of linear viscoelastic material (Shapery 1974) R ve (t) = t τ = R ve H (t τ) di(τ) For a layered system with a circular load: ve u vertical (t,z,r) = t τ = ve u H vertical (t τ,z,r) (Boltzmann s superposition integral) dσ(τ)
18 Layered Viscoelastic Algorithm (LAVA) Shapery s quasi-elastic approximation (1965; 1974) u H ve (t,r,z) u H e (t,r,z) Use layered elastic theory to get Use Boltzman s superposition integral to obtain VE response ve u vertical (t,z,r) = t τ = e u H vertical (t τ,z,r) dσ(τ) u H e (t,r,z) Unit load
19 Forward Algorithms: LAVA 1-2 Step 1: TT ii h 1 h 2 h 3 =Inf AC Base σ(t) Subgrade E subgrade, ν 3 1 E(t), ν 1 E base, ν 2 r= Step 3: (t), (inches) u ve H =(ue H rc = in rc = 8 in rc = 12 in rc = 18 in rc = 24 in rc = 36 in rc = 48 in rc = 6 in Relaxation modulus, E(t) psi Step 2: tt RRii = Number of time interval NE=1 tt ii aa TT (TTTT) t 1 3 Ri Reduced time, t R at 19 o C (sec) EE(tt RRii ) Step 4: Stress (psi) t Ri Reduced time t R, (sec) Time (sec) i AFK 5(1): Sub committee ve on advanced e models to understand behavior and performance of asphalt mixtures AFK 5: Committee u ( on ticharacteristics ) = u Hof ( asphalt ti paving τ j ) dmixtures σ ( τ j to ) meet structural whererequirements i = 1,214,... N s j=
20 Backcalculation algorithms Known variables: Number of layers Thickness of each layer Poisson s ratio of each layer Unknowns (iteratively backcalculated) E(t) sigmoid constants (4 unknowns) log( E(t) ) = c 1 + c 2 1+ exp( c 3 c 4 log(t R )) E i of unbound layers (typically 2-3 unknowns) Optimization algorithms: fminsearch, ga:genetic algorithm
21 Backcalculation algorithm o Once the E(t) sigmoid constants are known o o log( E(t) ) = c 1 + c 2 1+ exp( c 3 c 4 log(t R )) Prony series is fit to the E(t) master curve E(t) = E + N i=1 E i e E* is calculated using the following: t R ρ i E'= E * cos φ E"= E * sin φ N ( ) 2 ( ) 2 ( ) = E + E i 2πfρ i N i=1 ( ) = E i 2πfρ i i=1 1+ 2πfρ i ( ) πfρ i E* = E'+iE" E* = E' 2 +E" 2 φ = tan 1 (E"/ E')
22 Stress (psi) In order to get E* AND shift factor (a(t)) u VE (t) in rc = in rc = 7.99 in rc = 12.1 in rc = in rc = 24.2 in rc = in t(s) AC BASE SUBGRADE t(s) FWD T 1o C FWD T 2o C FWD T 3o C FWD T no C Backcalculation (BACKLAVA) Relaxation Modulus (psi) 1E+7 1E+6 1E+5 1E+4 T= C T=2C 1E+3 T=3C T=4C 1E+2 1E-8 1E-5 1E-2 1E+1 1E+4 1E+7 17 Time (sec)
23 Stress (psi) In order to get E* AND shift factor (a(t)) t(s) u VE (t) in rc = in rc = 7.99 in rc = 12.1 in rc = in rc = 24.2 in rc = in t(s) AC 1E+7 BASE SUBGRADE AC sublayer 1 T 1 = 2 o C AC sublayer 2 T 2 = 15 o C AC sublayer 3 T 3 = 1 o C 1 FWD Backcalculation (BACKLAVA) Relaxation Modulus (psi) 1E+6 1E+5 1E+4 T= C T=2C 1E+3 T=3C T=4C 1E+2 1E-8 1E-5 1E-2 1E+1 1E+4 1E+7 18 Time (sec) 18
24 Backcalculation example 6.9" 12" LTPP Section Asphalt Concrete (Linear Viscoelastic) ν=.35 Granular Base (Ebase) ν=.4 Subgrade (Esubgrade) ν= o C o C o C Deflection (in) Measured S1 Measured S3 Backcalculated S1 Backcalculated S Time (sec) Relaxation modulus, E(t) (psi) Backcalculated-1 Backcalculated Computed from measured D(t) Reduced time at 19 o C (sec)
25 Challenges Dynamics/wave propagation cannot be simulated with the method presented herein. Dynamic + viscoelastic forward solutions were recently developed, but computational speed of these algorithms make them impractical. Often the measured deflection time history is unreliable.
26 Summary o Consideration of viscoelasticity of AC is important o In-situ E* may be backcalculated with o o Single FWD run on an AC with large temperature gradient FWDs run at different temperatures o Accurate measurement of deflection time history is crucial
27 Mechanical Models for Asphalt Behavior and Performance Application of Linear Viscoelastic Models for Laboratory Evaluations
28 Learning Objective and Topics Explain the relationship between dynamic modulus and resilient modulus of asphalt concrete. Topics 1. Characterization of linear viscoelastic functions 2. Relationship between linear viscoelastic functions 3. Relationship between resilient modulus, M R, and dynamic modulus, E*
29 1. LVE Characterization Determine the value of coefficients used in mathematical models that define mechanical properties. Relevant material properties Stress response to unit input of strain = Relaxation modulus, E(t) Strain response to unit input of stress = Creep compliance, D(t) Sinusoidal response to sinusoidal input = Complex modulus/compliance, E*/D* Others: Shear modulus/compliance, bulk modulus/compliance, Poisson s ratio
30 1. LVE Characterization Review from Webinar 1 σ σ n σ n Simply put, the response of an arbitrary loading history is interpreted based on the summation of responses to a series of unit step inputs, e.g., a summation of finite stresses: time σ 4 σ 3 σ 2 σ 1 σ 3 σ 2 x 2 x 3 x 4 x n σ 1 A more common way to expressing the above is in its integral form: t dσ ε() t = Dt ( τ) dτ dτ
31 1. LVE Characterization Time Domain Creep Compliance, D(t) Test Constant load applied for prescribed period of time. Strain response is monitored Principle advantage Creep load is relatively easy to apply Principle concern Can easily exceed the LVE limits σ Input ε Response linear elastic or time independent σ 1 time D(t)=ε t (t)/σ 1 viscoelastic or time dependent ε=dσ 1 time
32 1. LVE Characterization Generalized Voight-Kelvin Model Generalized Maxwell Model (1) (2) (1) (2) N t t i D( t) = D + + Di 1 e τ η i= 1 ( ) N = + i= 1 t i E t E Ee ρ i October 212 Webinar
33 1. LVE Characterization Frequency Domain Complex Modulus, Test E*(ω) Constant sinusoidal stress or strain applied for prescribed temperature and frequency. Stress or strain response is monitored for amplitude and delay. Principle advantage Can ensure LVE strain limits are not exceeded. Principle concern Ensuring loading retains sinusoidal shape. σ Input ε Response time time Reported with respect to frequency and angular frequency ω = 2π f
34 2. LVE Functional Relationships Time-Domain Relationships In the case of elastic materials the inter-conversion or inter-relationship is straightforward D x E =1 What about time-dependent materials? t E ( t τ ) D( τ ) dτ = t E( τ ) D( t τ ) dτ = t 1. Exact analytical solution 2. Numerical solution 3. Semi-analytical solution t October 212 Webinar
35 2. LVE Functional Relationships Time-to-Frequency Relationships Exact relationships ( ) N = + i= 1 t i E t E Ee ρ i ( ω) E = E + E ωρ N 2 2 i i 2 2 i= 1 ωρi + 1 N i i= 1 ωρi + 1 i ( ω) 2 2 E = E ωρ Approximate relationships R = R( t) 2.1 R = λ R( t) 1 t= = πω f t= ω
36 3. M R and E* Relationship M R = engineering parameter to relate recoverable strain in AC material under simulated, field-like loading pulse. Stress σ.1 s.9 s Strain.1 s.9 s Resilient modulus is not a LVE response function ε r M R = σ ε ASTM D4123 AASHTO T322 NCHRP 1-28 r
37 3. M R and E* Exact Relationship Measurement E *, ϕ LVE Interconversion Theory ( ω) E = E + N 2 2 i i 2 2 i= 1 ωρi + 1 N i= 1 E ωρ t i E( t) = E Ee ρ + i t ( τ) ( ) E t D t dτ = t Stress σ ( t) 2 ωt σ sin t.1 = 2.1 < t σ.1 s.9 s t dσ ε() t = Dt ( τ) dτ dτ M R N t i D( t) D Di 1 e τ = + i= 1 = σ ε r Strain.1 s.9 s ε r
38 3. M R and E* Exact Relationship Lacroix et al. 27 3, S12.5C 3, S12.5CM Predicted M R, MPa 2, 1, Predicted M R, MPa 2, 1, 1, 2, 3, Measured M R, MPa 1, 2, 3, Measured M R, MPa 3, B25.C 3, S12.5FE Predicted M R, MPa 2, 1, Predicted M R, MPa 2, 1, AFK 5(1): Sub committee on advanced models to understand behavior and performance of asphalt mixtures 1, 2, 3, 1, 2, 3, Measured M R, MPa Measured M R, MPa
39 3. M R and E* Approx. Relationship 5 Hz versus M R Xiao 29 Lacroix 27 3 Dynamic Modulus ( E*, MPa 2 1 y = 1.134x R² = Resilient Modulus (M R ), MPa Can models help us explain the root cause of this correlation?
40 3. M R and E* Approx. Relationship Superposition allows decomposition of input load into separate components. Total response is summation of responses from each component. Stress σ.1 s.9 s = Stress Stress ε = ε ε r.5 s 1 s = Strain Strain +
41 3. M R and E* Approx. Relationship Sinusoidal Part Creep Part Stress Stress Assume steady state loading σ 2 D ε = ( ) ε = ( ) ( ).5 s.5 σ 1 s D D Approximate Interconversion ε.5 s R = R t t 1 1 = 1πω = f 1 1 εr ε.5 s ε1 s σ = = + 2 E* ( 1 ) E* ( 2 ) E* (.1 ) E* (.11) σ 1 σ 1 σ ε 1 1 ε 2 E * f 1 Hz ( = ) ( ) s 2 E * 1 s ( 2 σ σ ) 2 E* (.1 ) E* (.11) ε = = M E* ( f=4.8 Hz) AFK 5(1): Sub committee on advanced r models to understand behavior and performance of asphalt mixtures R AFK 5: Committee on characteristics of asphalt M paving mixtures * ( 4.8 to meet ) structural requirements R E
42 Summary Major uniaxial LVE response functions include the Creep Compliance, Relaxation Modulus, Complex Modulus, and Complex Compliance. The M R is an engineering response function based on a characteristic loading history similar to what occurs in a pavement system. LVE theory can be used to mathematically predict the resilient modulus from know response functions. Characterization Interconversion Integration (Exact) M R E* (f = 5 Hz) (Approximate)
43 Review of Linear Viscoelastic Behaviors
44 Linear Viscoelastic Behaviors Elastic P
45 Linear Viscoelastic Behaviors Elastic Viscoelastic Time, t = s P P
46 Linear Viscoelastic Behaviors Elastic Viscoelastic Time, t = 1 s s 1 s P P
47 Linear Viscoelastic Behaviors Elastic Viscoelastic Time, t = 1 s P s 1 s 1 s P Under a constant prescribed load (stress), viscoelastic materials undergo creep deformation (strain)
48 Linear Viscoelastic Behaviors Deformation, δ Excitation Reaction, P Elastic Solids time time Deformation δ Reaction, P Viscous Fluids Viscoelastic time Reaction, P time Under a prescribed deformation (strain), viscoelastic materials undergo relaxation of reaction (stress) Response Reaction
49 Linear Viscoelastic Behaviors Strain Input Stress Response ε 1 ε 2 ε 1 ε 2 ε 3 ε 3 ε 4 ε 4 Time Time
50 Linear Viscoelastic Behaviors Strain Input Stress Response T > 1 > T2 > T3 T4 T 4 T 3 T 2 T 1 Time Time
51 Linear Viscoelastic Behaviors Under cyclic or harmonic loading conditions we use slightly different terminology to define material response Load, P Deformation, δ time Relate the magnitude of excitation and the delay between excitation and response. Elastic Solids time P
52 Linear Viscoelastic Behaviors Time lag (phase angle) Stress, Strain Stress Strain 2πf σ ο ε o Complex Modulus σ o E * = ε o Phase Angle ϕ = ω t ϕ = 2π f t σ sin (ω t) o ε sin (ω t φ) o + Time
53 Linear Viscoelastic Behaviors When stress is input, R H (t) = D(t) and use: t dσ ε() t = Dt ( τ) dτ dτ When strain is input, R H (t) = E(t) and use: t dε σ() t = Et ( τ) dτ dτ When stress or strain are steady state sinusoidal use: σ = ( E *) ε ε = ( E *) σ
54 Linear Viscoelastic Behaviors Summary Viscoelastic responses exhibit a combination of elastic and viscous behaviors. This characteristic behavior means that relationships between stress and strain must include time-, frequency-, temperature- dependent functionality. In the next presentation we will briefly talk about how these relationships are characterized and how the relationships between these characteristics can be exploited for useful material prediction.
Mechanical Models for Asphalt Behavior and Performance
Mechanical Models for Asphalt Behavior and Performance All Attendees Are Muted Questions and Answers Please type your questions into your webinar control panel We will read your questions out loud, and
More informationLecture 7 Constitutive Behavior of Asphalt Concrete
Lecture 7 Constitutive Behavior of Asphalt Concrete What is a Constitutive Model? A constitutive model or constitutive equation is a relation between two physical quantities that is specific to a material
More informationFlexible Pavement Design
Flexible Pavement Design The Mechanistic-Empirical Way Presented by: Keith D. Herbold, P.E. 1 Presentation Outline What s new in flexible design Example of new design Differences Capabilities Tests and
More informationInterconversion of Dynamic Modulus to Creep Compliance and Relaxation Modulus: Numerical Modeling and Laboratory Validation
Final Report September 2016 Interconversion of Dynamic Modulus to Creep Compliance and Relaxation Modulus: Numerical Modeling and Laboratory Validation SOLARIS Consortium, Tier 1 University Transportation
More informationVISCOELASTIC FE MODELING OF ASPHALT PAVEMENTS AND ITS APPLICATION TO U.S. 30 PERPETUAL PAVEMENT. A dissertation presented to.
VISCOELASTIC FE MODELING OF ASPHALT PAVEMENTS AND ITS APPLICATION TO U.S. 30 PERPETUAL PAVEMENT A dissertation presented to the faculty of the Russ College of Engineering and Technology of Ohio University
More informationVECD (Visco-ElasticContinuum Damage): State-of-the-art technique to evaluate fatigue damage in asphalt pavements
VECD (Visco-ElasticContinuum Damage): tate-of-the-art technique to evaluate fatigue damage in asphalt pavements M. Emin Kutay, Ph.D., P.E. Assistant Professor Michigan tate University History of the Viscoelastic
More informationMechanistic Pavement Design
Seminar on Pavement Design System and Pavement Performance Models Reykjavik, 22. 23. March, 2007 Mechanistic Pavement Design A Road to Enhanced Understanding of Pavement Performance Sigurdur Erlingsson
More informationUnified Constitutive Model for Engineering- Pavement Materials and Computer Applications. University of Illinois 12 February 2009
Unified Constitutive Model for Engineering- Pavement Materials and Computer Applications Chandrakant S. Desai Kent Distinguished i Lecture University of Illinois 12 February 2009 Participation in Pavements.
More informationDEVELOPMENT OF A NEW SOLUTION FOR VISCOELASTIC WAVE PROPAGATION OF PAVEMENT STRUCTURES AND ITS USE IN DYNAMIC BACKCALCULATION.
DEVELOPMENT OF A NEW SOLUTION FOR VISCOELASTIC WAVE PROPAGATION OF PAVEMENT STRUCTURES AND ITS USE IN DYNAMIC BACKCALCULATION By Hyung Suk Lee A DISSERTATION Submitted to Michigan State University in partial
More informationMechanistic-Empirical Pavement Design Guide Distress Models
Mechanistic-Empirical Pavement Design Guide Distress Models By: Mohamed El-Basyouny Arizona State University Pavement Performance Models Symposium Laramie - Wyoming June 23, 2006 Outline Analysis Methodology
More information2002 Design Guide Preparing for Implementation
2002 Preparing for Implementation By Monte Symons 2003 NCUAPG Annual Meeting Excerpts from the 2002 Guide Implementation Package 2002 Presentation Overview Need for NCHRP 1-37A - Status Guide Basics Asphalt
More information2008 SEAUPG CONFERENCE-BIRMINGHAM, ALABAMA
Introduction Overview M E E Design Inputs MEPDG Where are we now MEPDG Inputs, Outputs, and Sensitivity Southeast Asphalt User Producer Group Bill Vavrik 19 November 2008 2 Implementation Timeframe DARWin
More informationAbvanced Lab Course. Dynamical-Mechanical Analysis (DMA) of Polymers
Abvanced Lab Course Dynamical-Mechanical Analysis (DMA) of Polymers M211 As od: 9.4.213 Aim: Determination of the mechanical properties of a typical polymer under alternating load in the elastic range
More informationPhenomenological models for binder rutting and fatigue. University of Wisconsin Research Team
Phenomenological models for binder rutting and fatigue University of Wisconsin Research Team Outline of Talk The need for measuring damage behavior Current efforts, and evolution of ideas Gaps and what
More informationABSTRACT. This dissertation presents a uniaxial viscoplastic constitutive model that is capable of
ABSTRACT YUN, TAEYOUNG. Development of a Viscoplastic Constitutive Model Using a Rate- Dependent Yield Criterion for HMA in Compression. (Under the direction of Dr. Y. Richard Kim). This dissertation presents
More informationUSE OF BBR TEST DATA TO ENHANCE THE ACCURACY OF G* -BASED WITCZAK MODEL PREDICTIONS
USE OF BBR TEST DATA TO ENHANCE THE ACCURACY OF G* -BASED WITCZAK MODEL PREDICTIONS Mekdim T. Weldegiorgis * PhD. Candidate, Department of Civil Engineering, University of New Mexico, USA * 1 University
More informationAnalysis of Hot-Mix Asphalt (HMA) Linear Viscoelastic and Bimodular Properties Using Uniaxial Compression and Indirect Tension (IDT) Tests
Analysis of Hot-Mix Asphalt (HMA) Linear Viscoelastic and Bimodular Properties Using Uniaxial Compression and Indirect Tension (IDT) Tests by Samer W. Katicha Dissertation submitted to the Faculty of the
More informationMSE 383, Unit 3-3. Joshua U. Otaigbe Iowa State University Materials Science & Engineering Dept.
Dynamic Mechanical Behavior MSE 383, Unit 3-3 Joshua U. Otaigbe Iowa State University Materials Science & Engineering Dept. Scope Why DMA & TTS? DMA Dynamic Mechanical Behavior (DMA) Superposition Principles
More informationNCAT Test Track Prediction
NCAT Test Track Prediction % Cracking Measured 60 50 40 30 20 10 0 O FW AW C RW R 5 7 9 11 13 15 % Damage Predicted Stress Sweep Rutting (SSR) Test Y. Richard Kim Jimmy D. Clark Distinguished University
More informationCreep Compliance Analysis Technique for the Flattened Indirect Tension Test of Asphalt Concrete
Creep Compliance Analysis Technique for the Flattened Indirect Tension Test of Asphalt Concrete Eshan V. Dave Andrew F. Braham Prof. William G. Buttlar Prof. Glaucio H. Paulino CONCREEP8, Ise-Shima, Japan
More informationStress Sweep Rutting (SSR) Test: AMPT
Stress Sweep Rutting (SSR) Test: AMPT Amir Ghanbari Graduate Research Assistant Y. Richard Kim Jimmy D. Clark Distinguished University Professor Alumni Distinguished Graduate Professor B. Shane Underwood
More informationEstimating Damage Tolerance of Asphalt Binders Using the Linear Amplitude Sweep
Standard Method of Test for Estimating Damage Tolerance of Asphalt Binders Using the Linear Amplitude Sweep AASHTO Designation: TP 101-14 American Association of State Highway and Transportation Officials
More informationMechanistic-Empirical Pavement Design Guide: A User s Perspective. Brian D. Prowell, Ph.D., P.E.
Mechanistic-Empirical Pavement Design Guide: A User s Perspective Brian D. Prowell, Ph.D., P.E. Empirical Approach Based on results of experiments or experience Scientific basis not established AASHTO
More informationACET 406 Mid-Term Exam B
ACET 406 Mid-Term Exam B SUBJECT: ACET 406, INSTRUCTOR: Dr Antonis Michael, DATE: 24/11/09 INSTRUCTIONS You are required to answer all of the following questions within the specified time (90 minutes).you
More informationAccelerated Testing Methodology for Long Term Durability of CFRP
IFREMER-ONR Workshop on Durability of Composites in a Marine Environment August 23 24, 22 IFREMER Centre, Nantes, France Accelerated esting Methodology for Long erm Durability of CFRP Masayuki Nakada*,
More informationLinear viscoelastic behavior
Harvard-MIT Division of Health Sciences and Technology HST.523J: Cell-Matrix Mechanics Prof. Ioannis Yannas Linear viscoelastic behavior 1. The constitutive equation depends on load history. 2. Diagnostic
More informationImpact of Water on the Structural Performance of Pavements
Impact of Water on the Structural Performance of Pavements S. Erlingsson Highway Engineering, VTI The Swedish National Road and Transport Research Institute, Linköping, Sweden & Faculty of Civil and Environmental
More informationNJDOT RESEARCH PROJECT MANAGER: Mr. Anthony Chmiel
Project Title: RFP NUMBER: CAIT NJDOT Bureau of Research QUARTERLY PROGRESS REPORT Evaluation of Poisson s Ratio NJDOT RESEARCH PROJECT MANAGER: Mr. Anthony Chmiel TASK ORDER NUMBER/Study Number: Task
More informationAsphalt Pavement Response and Fatigue Performance Prediction Using. Warm Mix Asphalt
Asphalt Pavement Response and Fatigue Performance Prediction Using the VECD Approach ApplicationApplication to Warm Mix Asphalt Y. Richard Kim, Ph.D, P.E. North Carolina State University Presented at the
More informationAsphalt Stiffness and Fatigue Parameters from Fast Falling Weight
Asphalt Stiffness and Fatigue Parameters from Fast Falling Weight Deflectometer (FastFWD) Tests 1 1 1 1 1 1 1 1 0 1 0 1 Sadaf Khosravifar, PhD Dynatest North America, Inc. 1 South Jefferson Street, Suite
More informationAnalysis of Non-Linear Dynamic Behaviours in Asphalt Concrete Pavements Under Temperature Variations
ENOC 2017, June 25 30, 2017, Budapest, Hungary Analysis of Non-Linear Dynamic Behaviours in Asphalt Concrete Pavements Under Temperature Variations Amal Abdelaziz *, Chun-Hsing Ho *, and Junyi Shan * *
More informationChapter 7. Highlights:
Chapter 7 Highlights: 1. Understand the basic concepts of engineering stress and strain, yield strength, tensile strength, Young's(elastic) modulus, ductility, toughness, resilience, true stress and true
More informationStandard Title Page - Report on Federally Funded Project 1. Report No. 2. Government Accession No. 3. Recipient s Catalog No.
Standard Title Page - Report on Federally Funded Project 1. Report No. 2. Government Accession No. 3. Recipient s Catalog No. FHWA/VTRC 07-CR1 4. Title and Subtitle 5. Report Date Determination of the
More informationCharacterizing Horizontal Response Pulse at the Bottom of Asphalt Layer Based on Viscoelastic Analysis
Technical Paper ISSN 1996-6814 Int. J. Pavement Res. Technol. 6(4):379-385 Copyright @ Chinese Society of Pavement Engineering Characterizing Horizontal Response Pulse at the Bottom of Asphalt Layer Based
More informationWilliam G. Buttlar Glaucio H. Paulino Harry H. Hilton Phillip B. Blankenship Hervé DiBenedetto. All colleagues and friends
Ph.D. Final Exam Asphalt Pavement Aging and Temperature Dependent Properties using a Functionally Graded Viscoelastic Model Eshan V. Dave June 5th 29 Department of Civil and Environmental Engineering University
More informationDetermining the asphalt mastercurve from free-free resonant testing on cylindrical samples
Determining the asphalt mastercurve from free-free resonant testing on cylindrical samples Nils RYDEN Engineering Geology, Faculty of Engineering, Lund University, Sweden Abstract There is a need to develop
More informationImplementation of M-E PDG in Kansas
Implementation of M-E PDG in Kansas Mustaque Hossain, Ph.D.,P.E. Kansas State University 1 Projects related to the M-E Guide Implementation and Calibration Kansas HMA Fatigue and Stiffness Study Pool Fund
More informationFlexible Pavement Stress Analysis
Flexible Pavement Stress Analysis Dr. Antonis Michael Frederick University Notes Courtesy of Dr. Christos Drakos, University of Florida Need to predict & understand stress/strain distribution within the
More informationFlexible Pavements Dynamic Response under a Moving Wheel
Flexible Pavements Dynamic Response under a Moving Wheel Angel Mateos, Ph.D. 1, Pablo de la Fuente Martín Ph.D. P.E. 2 and Javier Perez Ayuso 1 This paper presents the results from a research study carried
More informationDISPLACEMENT RATE AND TEMPERATURE EFFECT ON ASPHALT CONCRETE CRACKING POTENTIAL ASM TAMIM U. KHAN THESIS
DISPLACEMENT RATE AND TEMPERATURE EFFECT ON ASPHALT CONCRETE CRACKING POTENTIAL BY ASM TAMIM U. KHAN THESIS Submitted in partial fulfillment of the requirements for the degree of Master of Science in Civil
More informationField Rutting Performance of Various Base/Subbase Materials under Two Types of Loading
Field Rutting Performance of Various Base/Subbase Materials under Two Types of Loading Qiming Chen, Ph.D., P.E. (presenter) Murad Abu-Farsakh, Ph.D., P.E. Louisiana Transportation Research Center Apr.
More informationEstimating Fatigue Resistance Damage Tolerance of Asphalt Binders Using the Linear Amplitude Sweep
Standard Method of Test for Estimating Fatigue Resistance Damage Tolerance of Asphalt Binders Using the Linear Amplitude Sweep AASHTO Designation: TP 2b xx (LAST)101-1214 American Association of State
More informationThe Influence of Strain Amplitude, Temperature and Frequency on Complex Shear Moduli of Polymer Materials under Kinematic Harmonic Loading
Mechanics and Mechanical Engineering Vol. 21, No. 1 (2017) 157 170 c Lodz University of Technology The Influence of Strain Amplitude, Temperature and Frequency on Complex Shear Moduli of Polymer Materials
More informationEvaluation of Rutting Depth in Flexible Pavements by Using Finite Element Analysis and Local Empirical Model
American Journal of Engineering and Applied Sciences, 2012, 5 (2), 163-169 ISSN: 1941-7020 2014 Abed and Al-Azzawi, This open access article is distributed under a Creative Commons Attribution (CC-BY)
More informationMASSACHUSETTS INSTITUTE OF TECHNOLOGY DEPARTMENT OF MATERIALS SCIENCE AND ENGINEERING CAMBRIDGE, MASSACHUSETTS 02139
MASSACHUSES INSIUE OF ECHNOLOGY DEPARMEN OF MAERIALS SCIENCE AND ENGINEERING CAMBRIDGE, MASSACHUSES 02139 3.22 MECHANICAL PROPERIES OF MAERIALS PROBLEM SE 5 SOLUIONS 1. (Hertzber 6.2) If it takes 300 seconds
More informationMHA042 - Material mechanics: Duggafrågor
MHA042 - Material mechanics: Duggafrågor 1) For a static uniaxial bar problem at isothermal (Θ const.) conditions, state principle of energy conservation (first law of thermodynamics). On the basis of
More informationA NEW STEP TOWARDS PERFORMANCE BASED SPECIFICATIONS FOR ASPHALT PAVEMENTS
A NEW STEP TOWARDS PERFORMANCE BASED SPECIFICATIONS FOR ASPHALT PAVEMENTS Losa M. Associate Professor University of Pisa losa@ing.unipi.it Bacci R. PhD Student University of Pisa renato.bacci@ing.unipi.it
More informationMATERIAL MODELS FOR CRUMB RUBBER AND TDA. California State University, Chico
MATERIAL MODELS FOR CRUMB RUBBER AND TDA California State University, Chico Waste Tire Products for CE Applications Whole Tires Tire Shreds (TDA) Crumb Rubber/Tire Buffings Whole Tires TIRE DERIVED AGGREGATE
More informationRheological Properties and Fatigue Resistance of Crumb Rubber Modified Bitumen
Rheological Properties and Fatigue Resistance of Crumb Rubber Modified Bitumen F. Khodary Department of Civil Engineering, Institute of traffic and transport, section of road and pavement engineering,
More informationEshan V. Dave, Secretary of M&FGM2006 (Hawaii) Research Assistant and Ph.D. Candidate. Glaucio H. Paulino, Chairman of M&FGM2006 (Hawaii)
Asphalt Pavement Aging and Temperature Dependent Properties through a Functionally Graded Viscoelastic Model I: Development, Implementation and Verification Eshan V. Dave, Secretary of M&FGM2006 (Hawaii)
More informationAdvances in performance evaluation of asphalt binders
Advances in performance evaluation of asphalt binders Hussain U Bahia Professor University of Wisconsin, USA March 25, Lisbon, Potugal s:, design performance a, LNEC, 25 March 2010 Road Outline >Performance
More informationPart 7. Nonlinearity
Part 7 Nonlinearity Linear System Superposition, Convolution re ( ) re ( ) = r 1 1 = r re ( 1 + e) = r1 + r e excitation r = r() e response In the time domain: t rt () = et () ht () = e( τ) ht ( τ) dτ
More informationImproved Ultrasonic Pulse Velocity Technique for Bituminous Material Characterization
Improved Ultrasonic Pulse Velocity Technique for Bituminous Material Characterization Zhi-Yong Jiang 1, Joseph Ponniah, and Giovanni Cascante 3 1. Graduate student,. Adjunct Professor, 3. Associate Professor
More information3D Elasticity Theory
3D lasticity Theory Many structural analysis problems are analysed using the theory of elasticity in which Hooke s law is used to enforce proportionality between stress and strain at any deformation level.
More informationAPPENDIX A PROGRAM FLOW CHARTS
APPENDIX A PROGRAM FLOW CHARTS LIST OF FIGURES Figure Page A-1 Structure of the MEPDG software... A-1 A-2 Relationship of the reflection cracking design program of this project to the MEPDG design software...
More informationMECHANICS OF MATERIALS. EQUATIONS AND THEOREMS
1 MECHANICS OF MATERIALS. EQUATIONS AND THEOREMS Version 2011-01-14 Stress tensor Definition of traction vector (1) Cauchy theorem (2) Equilibrium (3) Invariants (4) (5) (6) or, written in terms of principal
More informationDEVELOPMENT AND EVALUATION OF AN HMA FRACTURE MECHANICS BASED MODEL TO PREDICT TOP-DOWN CRACKING IN HMA LAYERS
DEVELOPMENT AND EVALUATION OF AN HMA FRACTURE MECHANICS BASED MODEL TO PREDICT TOP-DOWN CRACKING IN HMA LAYERS By JIAN ZOU A DISSERTATION PRESENTED TO THE GRADUATE SCHOOL OF THE UNIVERSITY OF FLORIDA IN
More informationAMPT Cyclic Fatigue Test
AMPT Cyclic Fatigue Test Y. Richard Kim Jimmy D. Clark Distinguished University Professor Alumni Distinguished Graduate Professor NC State University North East Asphalt User/Producer Group Meeting October
More informationTECHNICAL REPORT STANDARD PAGE
TECHNICAL REPORT STANDARD PAGE 1. Report No. FHWA/LA.11/499 2. Government Accession No. 3. Recipient's Catalog No. 4. Title and Subtitle Characterization of Louisiana Asphalt Mixtures Using Simple Performance
More informationACKNOWLEDGMENT OF SPONSORSHIP
ACKNOWLEDGMENT OF SPONSORSHIP This work was sponsored by the American Association of State Highway and Transportation Officials, in cooperation with the Federal Highway Administration, and was conducted
More informationRheology of Asphalt Binders and Implications for Performance
Rheology of Asphalt Binders and Implications for Performance November 10, 2009 Dr. David Anderson Consultant and Professor Emeritus Penn State University DA.SC@COMCAST.NET Dr. Geoffrey Rowe President Abatech
More informationMETHODS FOR EVALUATING RESILIENT MODULI OF PAVING MATERIALS
Project Number ST 2019-7 Summary Report METHODS FOR EVALUATING RESILIENT MODULI OF PAVING MATERIALS sponsored by The State of Alabama Highway Department Montgomery, Alabama Frazier Parker, Jr. David J.
More informationWorkshop 4PBB First Steps for the perpetual pavement design: through the analysis of the fatigue life
Workshop 4PBB First Steps for the perpetual pavement design: through the analysis of the fatigue life N. Hernández & D. Suarez Introduction In Mexico, asphalt pavements often exhibit premature failures
More informationBackground PG G* sinδ
Full-Scale Accelerated Performance Testing for Superpave & Structural Validation Outcomes - Ongoing Activities - Future APT Experiments Hilton Head Island, South Carolina November 9-12, 2009 FHWA Turner-Fairbank
More informationElements of Polymer Structure and Viscoelasticity. David M. Parks Mechanics and Materials II February 18, 2004
Elements of Polymer Structure and Viscoelasticity David M. Parks Mechanics and Materials II 2.002 February 18, 2004 Outline Elements of polymer structure Linear vs. branched; Vinyl polymers and substitutions
More informationCharacterizing Nonlinear Viscoelastic Response of Asphaltic Materials
Characterizing Nonlinear Viscoelastic Response of Asphaltic Materials University of Texas at Austin Amit Bhasin Arash May, Motamed 21 Computational models of asphalt composites are increasingly being used
More informationSeismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design
Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design Elmer E. Marx, Alaska Department of Transportation and Public Facilities Michael Keever, California Department
More informationARC Update - Binder Fatigue
Asphalt Binder Expert Task Group ARC Update - Binder Fatigue Carl Johnson and Hussain U. Bahia University of Wisconsin - Madison September 16, 2009 Binder Fatigue Update Background Where we left off at
More informationStresses and Strains in flexible Pavements
Stresses and Strains in flexible Pavements Multi Layered Elastic System Assumptions in Multi Layered Elastic Systems The material properties of each layer are homogeneous property at point A i is the same
More informationMechanical Properties of Polymers. Scope. MSE 383, Unit 3-1. Joshua U. Otaigbe Iowa State University Materials Science & Engineering Dept.
Mechanical Properties of Polymers Scope MSE 383, Unit 3-1 Joshua U. Otaigbe Iowa State University Materials Science & Engineering Dept. Structure - mechanical properties relations Time-dependent mechanical
More informationUniversity Graz / Austria Institut für Chemie Volker Ribitsch
University Graz / Austria Institut für Chemie Volker Ribitsch 1 Rheology Oscillatory experiments Dynamic experiments Deformation of materials under non-steady conditions in the linear viscoelastic range
More informationINTRODUCTION TO STRAIN
SIMPLE STRAIN INTRODUCTION TO STRAIN In general terms, Strain is a geometric quantity that measures the deformation of a body. There are two types of strain: normal strain: characterizes dimensional changes,
More informationMECHANISTIC-EMPIRICAL LOAD EQUIVALENCIES USING WEIGH IN MOTION
MECHANISTIC-EMPIRICAL LOAD EQUIVALENCIES USING WEIGH IN MOTION Prepared By: Curtis Berthelot Ph.D., P.Eng. Dept. of Civil Engineering University of Saskatchewan Tanya Loewen Dept. of Civil Engineering
More informationStress Rotations Due to Moving Wheel Loads and Their Effects on Pavement Materials Characterization
Stress Rotations Due to Moving Wheel Loads and Their Effects on Pavement Materials Characterization Erol Tutumluer June 9, 2005 OMP Brown Bag Seminar Presentation FAA Center of Excellence for Airport Technology
More informationPrediction of Complex Shear Modulus and Fracture Properties of Asphalt Binders with Oxidative Aging
Prediction of Complex Shear Modulus and Fracture Properties of Asphalt Binders with Oxidative Aging By Haifang Wen, PhD, PE Colf Distinguished Professor Director of Washington Center for Asphalt Technology
More informationVerification of the dissipated energy based fatigue model using field data
Rowan University Rowan Digital Works Theses and Dissertations 3-2-2015 Verification of the dissipated energy based fatigue model using field data Thomas Redles Follow this and additional works at: http://rdw.rowan.edu/etd
More informationU.S. South America Workshop. Mechanics and Advanced Materials Research and Education. Rio de Janeiro, Brazil. August 2 6, Steven L.
Computational Modeling of Composite and Functionally Graded Materials U.S. South America Workshop Mechanics and Advanced Materials Research and Education Rio de Janeiro, Brazil August 2 6, 2002 Steven
More informationCOMPARISON BETWEEN LABORATORY AND FIELD MEASURED RESILIENT MODULUS FOR FLEXIBLE PAVEMENT
International Journal of Civil Engineering and Technology (IJCIET) Volume 9, Issue 10, October 2018, pp. 558 568, Article ID: IJCIET_09_10_057 Available online at http://www.iaeme.com/ijciet/issues.asp?jtype=ijciet&vtype=9&itype=10
More informationTRB DETERMINATION OF CRITICAL BENDING STRESSES IN THE PCC LAYER WITH ASPHALT OVERLAY
Saxena and Khazanovich 0 TRB - DETERMINTION OF CRITICL BENDING STRESSES IN THE PCC LYER WITH SPHLT OVERLY Priyam Saxena, Ph.D University of Minnesota Department of Civil Engineering 00 Pillsbury Drive
More informationALACPA-ICAO Seminar on PMS. Lima Peru, November 2003
ALACPA-ICAO Seminar on PMS Lima Peru, 19-22 November 2003 Airport Pavements FWD/HWD Testing and Evaluation By: Frank B. Holt Vice President Dynatest International A/S Dynamic Testing The method of FWD/HWD
More informationPLEASE SCROLL DOWN FOR ARTICLE
This article was downloaded by:[pan, Ernian] [Pan, Ernian] On: 23 May 2007 Access Details: [subscription number 778682963] Publisher: Taylor & Francis Informa Ltd Registered in England and Wales Registered
More informationDetermination of Activation Energy for Glass Transition of an Epoxy Adhesive Using Dynamic Mechanical Analysis
See discussions, stats, and author profiles for this publication at: https://www.researchgate.net/publication/51099575 Determination of Activation Energy for Glass Transition of an Epoxy Adhesive Using
More informationINTRODUCTION TO PAVEMENT STRUCTURES
INTRODUCTION TO PAVEMENT STRUCTURES A pavement is a structure composed of structural elements, whose function is to protect the natural subgrade and to carry the traffic safety and economically. As a wheel
More informationPredeformation and frequency-dependence : Experiment and FE analysis
Predeformation and frequency-dependence : Experiment and FE analysis Nidhal Jridi 1,2,*, Michelle Salvia 2, Adel Hamdi 1, Olivier Bareille 2, Makrem Arfaoui 1, Mohammed Ichchou 2, Jalel Ben Abdallah 1
More informationRheology. October 2013
Rheology Georges Cailletaud Centre des Matériaux MINES ParisTech/CNRS October 2013 Georges Cailletaud Rheology 1/44 Contents 1 Mechanical tests Structures Representative material elements 2 Rheological
More informationEvaluation of Poisson s Ratio of Asphalt Concrete
University of Arkansas, Fayetteville ScholarWorks@UARK Theses and Dissertations 1-2016 Evaluation of Poisson s Ratio of Asphalt Concrete Elvis Alexander Castillo Camarena University of Arkansas, Fayetteville
More informationDetermination of Resilient Modulus Model for Road-Base Material
JOURNAL OF APPLIED SCIENCES RESEARCH ISSN: 1819-544X Published BY AENSI Publication EISSN: 1816-157X http://www.aensiweb.com/jasr 2017 January; 13(1): pages 10-16 Open Access Journal Determination of Resilient
More informationLecture 3: Stresses in Rigid Pavements
Lecture 3: Stresses in Rigid Pavements Nature of Responses under Flexible and Rigid Plates Flexible plate: Uniform Contact Pressure Variable Deflection Profile Flexible Plate Rigid Plate plate: Non-Uniform
More informationGM Rowe and DA Anderson. Binder ETG Meeting, April 2014
GM Rowe and DA Anderson Binder ETG Meeting, April 2014 What is relaxation spectra Historical perspective What it means Other simplifications Field correlations Black space Discrete Model the asphalt by
More informationNebraska Transportation Center
Nebraska Transportation Center Report # MPMC-01 Final Report 26-1121-4004-001 Research on Roadway Performance and Distress at Low Temperature Yong-Rak Kim, Ph.D. Associate Professor Department of Civil
More informationCookbook for Rheological Models Asphalt Binders
CAIT-UTC-062 Cookbook for Rheological Models Asphalt Binders FINAL REPORT May 2016 Submitted by: Offei A. Adarkwa PhD in Civil Engineering Nii Attoh-Okine Professor Pamela Cook Unidel Professor University
More informationDeformation of Polymers. Version 2.1. Boban Tanovic, MATTER David Dunning, University of North London
Deformation of Polymers Version 2.1 Boban Tanovic, MATTER David Dunning, University of North London Assumed Pre-knowledge It is assumed that the user is familiar with the terms elasticity, stress, strain,
More informationMECHANISTIC CHARACTERIZATION OF RESILIENT MODULI FOR UNBOUND PAVEMENT LAYER MATERIALS
MECHANISTIC CHARACTERIZATION OF RESILIENT MODULI FOR UNBOUND PAVEMENT LAYER MATERIALS Except where reference is made to the work of others, the work described in this thesis is my own or was done in collaboration
More informationNumerical Modelling of Dynamic Earth Force Transmission to Underground Structures
Numerical Modelling of Dynamic Earth Force Transmission to Underground Structures N. Kodama Waseda Institute for Advanced Study, Waseda University, Japan K. Komiya Chiba Institute of Technology, Japan
More informationSensitivity Analysis Of Aashto's 2002 Flexible And Rigid Pavement Design Methods
University of Central Florida Electronic Theses and Dissertations Masters Thesis (Open Access) Sensitivity Analysis Of Aashto's 2002 Flexible And Rigid Pavement Design Methods 2006 Sanjay Shahji University
More informationMultiple Impact Surface Waves (MISW) or Multichannel Analysis of Surface Waves (MASW) Nils Rydén, Lund University, Sweden
Multiple Impact Surface Waves (MISW) or Multichannel Analysis of Surface Waves (MASW) Nils Rydén, Lund University, Sweden Outline Background NDT of pavements Wave propagation in slabs (plates) and pavement
More informationTECHNICAL PAPER INVESTIGATION INTO THE VALIDATION OF THE SHELL FATIGUE TRANSFER FUNCTION
Authors: TECHNICAL PAPER INVESTIGATION INTO THE VALIDATION OF THE SHELL FATIGUE TRANSFER FUNCTION Anthony Stubbs (Presenter), BE(Hons), Masters student, University of Canterbury. aps49@student.canterbury.ac.nz.
More informationFATIGUE LIFE PREDICTIONS FOR ASPHALT CONCRETE SUBJECTED TO MULTIPLE AXLE LOADINGS
FATIGUE LIFE PREDICTIOS FOR ASPHALT COCRETE SUBJECTED TO MULTIPLE AXLE LOADIGS Karim Chatti, Hyungsuk Lee and Chadi El Mohtar Assistant Professor, Dept. of Civil and Environmental Engineering, Michigan
More informationABSTRACT. PARK, HEE MUN. Use of Falling Weight Deflectometer Multi-Load Level Data for
ABSTRACT PARK, HEE MUN. Use of Falling Weight Deflectometer Multi-Load Level Data for Pavement Strength Estimation. (Under the direction of Y. Richard, Kim). The objective of this study is to describe
More informationDynamic Modulus of Asphalt Mixtures for Development of
JOURNAL PAPER TYPE Journal of Testing and Evaluation, Sept 2002 Vol XX, No. X Paper ID: Available online at: www.astm.org Published XXXX Lee, K. 1, Kim, H. 2, Kim, N. 3, Kim, Y 4 Dynamic Modulus of Asphalt
More information