Introduction. Measurement of temperature is generally considered to be one of the simplest and most accurate measurements performed in engineering.
|
|
- Lee Jackson
- 6 years ago
- Views:
Transcription
1 Slide Nr. 0 of 15 Slides Introduction Measurement of temperature is generally considered to be one of the simplest and most accurate measurements performed in engineering. Some important considerations when measuring temperature are: 1. The contact between the sensor and the substance being measured should be satisfactory 2. The sensor should be small enough not to disturb the temperature conditions or cause too much thermal lag during transient testing. 3. There should be no chemical reactions between the sensor and the substance which will cause heat to be produced or absorbed.
2 Slide Nr. 1 of 15 Slides Definition of temperature a. According to thermodynamic basis: Temperature is related to heat. If two bodies at different temperatures are in contact, or in view of each other, heat flows from the one at higher temperature to the other at lower temperature. b. According to the kinetic theory of gases: Temperature is related to the average kinetic energy of an ideal gas. The relation is given by pv mr T
3 Slide Nr. 2 of 15 Slides Temperature scales
4 Slide Nr. 3 of 15 Slides Considerations of s (1) Thermodynamic equilibrium To measure temperature, it is necessary to establish a thermodynamic equilibrium between the body and the device to sense the temperature; e.g. bulb thermometers or thermocouple wire.
5 Slide Nr. 4 of 15 Slides Considerations of s (2) Thermal characteristics of temperature sensors Temperature sensors posses thermal characteristic which largely depend upon their size and shape and the materials from which they are made. Disturbance of the medium The introduction of temperature sensors into body tends to modify (change) the temperature conditions at that point. Also the body will be modified by any holes drilled in it to insert the probe, etc. The measured value will therefore be the modified value and not the true value.
6 Slide Nr. 5 of 15 Slides Considerations of s (3) Error due to signal transmission In most cases, the sensor is connected to a recording instrument by means of an intermediate system. The intermediate system and the recorder may be subjected to temperature or other changes and so compensating device are usually to reduce or eliminate errors. Ways of energy transfer Heat is transferred from place to place by conduction, convection and radiation. It is necessary to take these into account when choosing a temperature measuring method.
7 Slide Nr. 6 of 15 Slides Classification of Temperature Measuring Devices 1. Non electrical methods: a. Expansion thermometers: Expansion of solids. Expansion of liquids. Perfect gas thermometers b. Refractory cones, paints and crayons. 2. Electrical methods: a. Electrical resistance. b. Thermocouples. 3. Radiation and optical: a. Total radiation pyrometer. b. Photoelectric pyrometer. c. Optical pyrometer.
8 Slide Nr. 7 of 15 Slides Non-Electrical Temperature Measuring Devices Expansion thermometers Most solids and liquids expand when they are subjected to an increase in temperature. The direct observation is an increase in their size. This is used to indicate temperature in many thermometers. 1. Expansion of solids This includes: a. Solid rod thermometers or thermostat. b. Bimetallic thermometers. Solid rod and bimetallic thermometer are designed using the principle that some metals expand more than others when they are subjected to the same rise in temperature.
9 Slide Nr. 8 of 15 Slides Rod Thermostat The change (DL) of the original length of a solid due to a change (DT) of temperature is given by: DL L DT The displacement of rod A is (x) which is given by: x DT A B
10 Slide Nr. 9 of 15 Slides Bimetallic Thermometer (1) L L B A r r d L L B A 1 1 B A r d 1 A B A If Invar is used for strip A, then α A is virtually zero r d B It is seen that for thinner strips, r is smaller, i.e. more bending occurs.
11 Slide Nr. 10 of 15 Slides Bimetallic Thermometer (2) The following are essential characteristics of the bimetal strip thermometer: Inexpensive: often used instead of liquid in glass thermometers. Compact: the volume of metal used in the protective sheath is small and thus of low thermal capacity. This of course improved its response. Robust: good resistance to mechanical shock due freely floating spindle. Close linearity: throughout the temperature range. Range of application: Accuracy: low temperature -30 C to 200 C high temperature 0 C to 550 C low temperature 1% of scale range high temperature 2% of scale range To increase the sensitivity, bimetal are coiled in helical form.
12 Slide Nr. 11 of 15 Slides Liquid in Glass Thermometer (1) The increase in temperature causes the liquid and the container to expand. The change (DV 1 ) of the volume (V 1 ) of a liquid due to change (DT) of its temperature is given by DV V1 1 1 D T The container will also have a volume changes (DV c ), and its temperature changes is the same (DT), then DV c V c c DT But V 1 = V c. Hence the apparent volume changes (DV) DV DV DV V T 1 c 1 c c D
13 Slide Nr. 12 of 15 Slides Liquid in Glass Thermometer (2) The advantages of liquid in glass thermometers are: 1. Inexpensive 2. Simple in design 3. Portable 4. No additional indication instruments are required The disadvantages of liquid in glass thermometers are: 1. Fragile and can be easily braked. 2. Not suitable for distant readings 3. Not suitable for surface temperature measurements 4. Not suitable for dynamic measurements because it possesses high heat capacity
14 Slide Nr. 13 of 15 Slides Immersion Errors (1) Complete immersion: By definition, if the complete bulb and stem are immersed at the same temperature, the thermometer is completely immersed. Total immersion: Total immersion applies to the situation where all the thermometric liquid, i.e., all the mercury in the bulb, the contraction chamber, and the stem, is at the temperature of interest. Partial immersion: One way around the problem of scale visibility and the need to move the thermometer is to immerse the thermometer to some fixed depth so that most, but not all, of the mercury is at the temperature of interest.
15 Slide Nr. 14 of 15 Slides Immersion Errors (2) For partial immersion thermometers, the true temperature reading t is given by: t t i N t 2 t1 K where t i is the indicated temperature, N is the length of emergent column expressed in degrees, as determined by the thermometer scale, t 2 is the mean temperature of the emergent column when calibrated (i.e., the stem temperature on a certificate for partial immersion or the thermometer reading for a total-immersion certificate), t 1 is the mean temperature of the emergent column in use and k is a coefficient of apparent expansion of the thermometric liquid used in the glass of which the thermometer stem is made
16 Slide Nr. 15 of 15 Slides
Section 7. Temperature Measurement
Section 7 Temperature Measurement 7/25/2017 Engineering Measurements 7 1 Working Definition Temperature is a measure of the average kinetic energy of the molecules that make of a substance. After time,
More informationChapter 16 Temperature and Heat
Chapter 16 Temperature and Heat 16-1 Temperature and the Zeroth Law of Thermodynamics Definition of heat: Heat is the energy transferred between objects because of a temperature difference. Objects are
More informationAl-Saudia Virtual Academy Online tuiton Pakistan Online Tutor Pakistan. Heat
Al-Saudia Virtual Academy Online tuiton Pakistan Online Tutor Pakistan Heat Nature of Heat: Heat is the transfer of energy (every in transit) from one body to another due to the temperature difference
More informationTemperature Measurement
MECE 3320 Measurements & Instrumentation Temperature Measurement Dr. Isaac Choutapalli Department of Mechanical Engineering University of Texas Pan American Introduction Temperature is one of the most
More informationChapters 16 Temperature and Heat
Chapters 16 Temperature and Heat 1 Overview of Chapter 16 Temperature and the Zeroth Law of Thermodynamics Temperature Scales Thermal Expansion Heat and Mechanical Work Specific Heat Conduction, Convection,
More informationLecture 22. Temperature and Heat
Lecture 22 Temperature and Heat Today s Topics: 0 th Law of Thermodynamics Temperature Scales Thermometers Thermal Expansion Heat, Internal Energy and Work Heat Transfer Temperature and the Zeroth Law
More information1 THE CONCEPT OF TEMPERATURE
1 THE CONCEPT OF TEMPERATURE 1 1.1 Historical Perspective, 2 1.2 Early Definitions of Temperature, 9 1.3 A Simple Qualitative Definition of Temperature, 10 1.4 Units of Temperature for Various Temperature
More informationWeek-7 Assignment-1. The due date for submitting this assignment has passed. (1/273.15)th of the normal freezing point of water
X reviewer2@nptel.iitm.ac.in Courses» Chemical Process Instrumentation Unit 8 - Week 7 Announcements Course Ask a Question Progress Mentor Course outline How to access the portal Week-7 Assignment-1 The
More information1. How much heat was needed to raise the bullet to its final temperature?
Name: Date: Use the following to answer question 1: A 0.0500-kg lead bullet of volume 5.00 10 6 m 3 at 20.0 C hits a block that is made of an ideal thermal insulator and comes to rest at its center. At
More informationPhysical Science Chapter 5 Cont2. Temperature & Heat
Physical Science Chapter 5 Cont2 Temperature & Heat What are we going to study? Temperature Heat Specific Heat and Latent Heat Heat Transfer Phases of Matter The Kinetic Theory of Gases Thermodynamics
More informationUniversity of Technology Dr. louay A.Mahdi Department of Machines and Equipments Engineering Branches: General, Refrigeration and Air conditioning,
1 Introduction: The first recorded temperature measurement was carried out by Galileo at the end of the sixteenth century. His thermometer depended on the expansion of air. Some form of scale was attached
More informationLecture Outlines Chapter 16. Physics, 3 rd Edition James S. Walker
Lecture Outlines Chapter 16 Physics, 3 rd Edition James S. Walker 2007 Pearson Prentice Hall This work is protected by United States copyright laws and is provided solely for the use of instructors in
More informationHeat and temperature are related and often confused, but they are not the same.
Heat and temperature are related and often confused, but they are not the same. Heat Definition: Heat is energy that is transferred from one body to another as a result of a difference in temperature Symbol:
More informationChapter 16. Copyright 2010 Pearson Education, Inc.
Chapter 16 Temperature and Heat Units of Chapter 16 Temperature and the Zeroth Law of Thermodynamics Temperature Scales Thermal Expansion Heat and Mechanical Work Specific Heats Conduction, Convection,
More informationChapter 17. Temperature. Dr. Armen Kocharian
Chapter 17 Temperature Dr. Armen Kocharian Temperature We associate the concept of temperature with how hot or cold an objects feels Our senses provide us with a qualitative indication of temperature Our
More informationHEAT AND TEMPERATURE Vikasana-Bridge Course 2012
HEAT AND TEMPERATURE TOPICS Introduction Effects of heat Specific heat Basics of thermodynamics Introduction Heat may be defined as energy in transit from a high temperature region to a lower temperature
More informationThermal energy. Thermal energy is the internal energy of a substance. I.e. Thermal energy is the kinetic energy of atoms and molecules.
Thermal energy Thermal energy is the internal energy of a substance. I.e. Thermal energy is the kinetic energy of atoms and molecules. Heat is the transfer of thermal energy between substances. Until the
More informationSiddharth Institute of Engineering & Technology
SIDDHARTH INSTITUTE OF ENGINEERING & TECHNOLOGY :: PUTTUR (AUTONOMOUS) (Approved by AICTE, New Delhi & Affiliated to JNTUA, Anantapuramu) (Accredited by NBA & Accredited by NAAC with A Grade) (An ISO 9001:2008
More informationThermodynamic System. A thermodynamic system is a volume in space containing a quantity of matter that is being studied for thermodynamic analysis.
Thermodynamic System A thermodynamic system is a volume in space containing a quantity of matter that is being studied for thermodynamic analysis. The system is bounded by an arbitrary surface called the
More informationUnit 6: Thermal Physics
Unit 6: Thermal Physics 6.1 Thermal Expansion Objectives Describe qualitatively the thermal expansion of solids, liquids, and gases at constant pressure Identify and explain some of the everyday applications
More informationTick the box next to those resources for which the Sun is also the source of energy.
1 (a) The source of solar energy is the Sun. Tick the box next to those resources for which the Sun is also the source of energy. coal geothermal hydroelectric nuclear wind [2] (b) Fig. 4.1 shows a solar
More informationPhysics THERMAL PHYSICS/EXPANSION. Mr Rishi Gopie
THERMAL PHYSICS/EXPANSION Mr Rishi Gopie 2 Changes in Size Generally, when heat is added to a body/system it undergoes expansion, i.e. an increase in size, and when heat is removed from the body/system
More informationLecture 2: Zero law of thermodynamics
Lecture 2: Zero law of thermodynamics 1. Thermometers and temperature scales 2. Thermal contact and thermal equilibrium 3. Zeroth law of thermodynamics 1. Thermometers and Temperature scales We often associate
More informationThermometry. History. History 1/21/18. The art or science of temperature observation
Thermometry The art or science of temperature observation History No one person credited with the invention of the thermometer; developed over time Avicenna used this principal to show that hotness and
More informationChapter 10. Thermal Physics
Chapter 10 Thermal Physics Thermal Physics Thermal physics is the study of Temperature Heat How these affect matter Thermal Physics, cont Descriptions require definitions of temperature, heat and internal
More informationVALLIAMMAI ENGINEERING COLLEGE
VALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur 603 203 DEPARTMENT OF ELECTRONICS AND INSTRUMENTATION ENGINEERING QUESTION BANK V SEMESTER EI6502 -INDUSTRIAL INSTRUMENTATION I Regulation 2013
More informationControl Engineering BDA30703
Control Engineering BDA30703 Lecture 4: Transducers Prepared by: Ramhuzaini bin Abd. Rahman Expected Outcomes At the end of this lecture, students should be able to; 1) Explain a basic measurement system.
More informationChapter 6. Fiber Optic Thermometer. Ho Suk Ryou
Chapter 6. Fiber Optic Thermometer Ho Suk Ryou Properties of Optical Fiber Optical Fiber Composed of rod core surrounded by sheath Core: conducts electromagnetic wave Sheath: contains wave within the core
More informationChapter 6 Temperature Measurement (Revision 2.0, 1/12/2009)
Chapter 6 emperature Measurement (Revision 2.0, /2/2009). Introduction his Chapter looks that various methods of temperature measurement. Historically, there are two temperature measurement scales: he
More information3. EFFECTS OF HEAT. Thus, heat can be defined as a form of energy that gives the sensation of hotness or coldness
3. EFFECTS OF HEAT In the previous class you have learnt that heat is a form of energy. Heat can be obtained from various sources like the sun, fire, etc. When we read the weather forecast we observe that
More informationthe energy of motion!
What are the molecules of matter doing all the time?! Heat and Temperature! Notes! All matter is composed of continually jiggling atoms or molecules! The jiggling is! If something is vibrating, what kind
More informationHeat & Temperature. Grade 7 Science - Unit 2 Pgs
Heat & Temperature Grade 7 Science - Unit 2 Pgs 104-225 4.1 Temperature PTemperature is the measure of how much heat is in a substance. PTemperature is measured in degrees Celcius ( C) PIt is difficult
More informationP5 Heat and Particles Revision Kinetic Model of Matter: States of matter
P5 Heat and Particles Revision Kinetic Model of Matter: States of matter State Size Shape Solid occupies a fixed volume has a fixed shape Liquid occupies a fixed volume takes the shape of its container
More informationPURE PHYSICS THERMAL PHYSICS (PART I)
PURE PHYSICS THERMAL PHYSICS (PART I) 1 The kinetic theory of matter states that all matters are made up of or, which are in and motion. forces hold the atoms or molecules together. The nature of these
More informationPhysics 121, April 10, Temperature/Heat. Department of Physics and Astronomy, University of Rochester
Physics 121, April 10, 2008. Temperature/Heat. Physics 121. April 10, 2008. Course Information Topics to be discussed today: Temperature Physics 121. April 10, 2008. Homework set # 8 is due on Saturday
More informationChapter 17 Temperature and heat
Chapter 17 Temperature and heat 1 Temperature and Thermal Equilibrium When we speak of objects being hot and cold, we need to quantify this by some scientific method that is quantifiable and reproducible.
More informationTemperature Scales. Temperature, and Temperature Dependent on Physical Properties. Temperature. Temperature Scale
Temperature Scales The Celsius, Fahrenheit, and Kelvin Temperature Scales: Temperature, and Temperature Dependent on Physical Properties Physics Enhancement Programme Dr. M.H. CHAN, HKBU 9 T F T 5 T T
More informationChapter 16 Temperature and Heat
Chapter 16 Temperature and Heat Temperature and the Zeroth Law of Thermodynamics Temperature Scales Thermal Expansion Heat and Mechanical Work Specific Heats Conduction, Convection, and Radiation 16-1
More informationOptics Definitions. The apparent movement of one object relative to another due to the motion of the observer is called parallax.
Optics Definitions Reflection is the bouncing of light off an object Laws of Reflection of Light: 1. The incident ray, the normal at the point of incidence and the reflected ray all lie in the same plane.
More informationCIE Physics IGCSE. Topic 2: Thermal Physics
CIE Physics IGCSE Topic 2: Thermal Physics Summary Notes Simple kinetic molecular model of matter Molecular model Solids Molecules close together in regular pattern Strong intermolecular forces of attraction
More informationUnit 5 Thermodynamics
Unit 5 Thermodynamics Unit 13: Heat and Temperature Unit 14: Thermal Expansion /Heat Exchange/ Change of Phase Test: Units 13-14 Thermal Energy The total kinetic and potential energy of all the molecules
More informationIntroduction to Heat and Mass Transfer. Week 1
Introduction to Heat and Mass Transfer Week 1 This Lecture Course Organization Introduction Basic Modes of Heat Transfer Application Areas Instructor Information Professor Chang-Da Wen 温昌達» Office: 91713
More informationDr.Salwa Alsaleh fac.ksu.edu.sa/salwams
Dr.Salwa Alsaleh Salwams@ksu.edu.sa fac.ksu.edu.sa/salwams What is Temperature? It is the measurement of the AVERAGE kinetic energy of the particles of matter. Temperature We associate the concept of temperature
More information4.1. Physics Module Form 4 Chapter 4 - Heat GCKL UNDERSTANDING THERMAL EQUILIBRIUM. What is thermal equilibrium?
4.1 4 UNDERSTANDING THERMAL EQUILIBRIUM What is thermal equilibrium? 1. ( Heat, Temperature ) is a form of energy that flows from a hot body to a cold body. 2. The SI unit for ( heat, temperature) is Joule,
More informationSubject: BT6008 Process Measurement and Control. The General Control System
WALJAT COLLEGES OF APPLIED SCIENCES In academic partnership with BIRLA INSTITUTE OF TECHNOLOGY Question Bank Course: Biotechnology Session: 005-006 Subject: BT6008 Process Measurement and Control Semester:
More informationLABORATORY MANUAL MEASUREMENTS & INSTRUMENTATION (ME- 318-F)
LABORATORY MANUAL MEASUREMENTS & INSTRUMENTATION (ME- 318-F) LIST OF THE EXPERIMENT S. NO. NAME OF THE EXPERIMENT PAGE NO FROM TO 1. To measure stress and strain using strain gauge mounted on a cantilever
More informationChapter 4: Heat Capacity and Heat Transfer
Chapter 4: Heat Capacity and Heat Transfer Chapter 4: Heat Capacity and Heat Transfer Chapter 4: Heat Capacity and Heat Transfer 4.1 Material Structure 4.2 Temperature and Material Properties 4.3 Heating
More informationBasic Concepts of Thermodynamics
Basic Concepts of Thermodynamics.. Introduction to kinetic theory of gases... Definition of thermodynamics..3. Thermodynamic systems system, boundary and surroundings closed system open system isolated
More informationHigh temperature He is hot
Lecture 9 What is Temperature and Heat? High temperature He is hot Some important definitions * Two objects are in Thermal contact with each other if energy can be exchanged between them. Thermal equilibrium
More informationto calculate gravitational force. d - Know how changes in mass or distance affect the gravitational force between two objects.
PHYSICS 2 ND SEMESTER REVIEW Semester Test Notes: - You may use a 5 x 8 index card (NO LARGER) with equations, diagrams, and notes. - Your index card will be turned in with your test. - Most constants
More informationEnthalpy and Adiabatic Changes
Enthalpy and Adiabatic Changes Chapter 2 of Atkins: The First Law: Concepts Sections 2.5-2.6 of Atkins (7th & 8th editions) Enthalpy Definition of Enthalpy Measurement of Enthalpy Variation of Enthalpy
More informationTHERMOCOUPLE CHARACTERISTICS TRAINER
THERMOCOUPLE CHARACTERISTICS TRAINER (Model No : ) User Manual Version 2.0 Technical Clarification /Suggestion : / Technical Support Division, Vi Microsystems Pvt. Ltd., Plot No :75,Electronics Estate,
More informationFirst Law of Thermodynamics Second Law of Thermodynamics Mechanical Equivalent of Heat Zeroth Law of Thermodynamics Thermal Expansion of Solids
Slide 1 / 66 1 What is the name of the following statement: "When two systems are in thermal equilibrium with a third system, then they are in thermal equilibrium with each other"? A B C D E First Law
More information: INSTRUMENTATION AND PROCESS CONTROL COURSE CODE : 6071 COURSE CATEGORY : A PERIODS/ WEEK : 5 PERIODS/ SEMESTER : 75 CREDIT : 5 TIME SCHEDULE
COURSE TITLE : INSTRUMENTATION AND PROCESS CONTROL COURSE CODE : 6071 COURSE CATEGORY : A PERIODS/ WEEK : 5 PERIODS/ SEMESTER : 75 CREDIT : 5 TIME SCHEDULE MODULE TOPIC PERIODS 1 Measuring Instruments
More informationChapter 18 Temperature, Heat, and the First Law of Thermodynamics. Thermodynamics and Statistical Physics
Chapter 18 Temperature, Heat, and the First Law of Thermodynamics Thermodynamics and Statistical Physics Key contents: Temperature scales Thermal expansion Temperature and heat, specific heat Heat and
More informationThermal Sensors and Actuators
Thermal Sensors and Actuators Part I Fundamentals of heat transfer Heat transfer occurs where there is a temperature gradient until an equilibrium is reached. Four major mechanism Thermal conduction Natural
More informationEstimate, for this water, the specific heat capacity, specific heat capacity =... J kg 1 K 1. the specific latent heat of vaporisation.
1 A kettle is rated as 2.3 kw. A mass of 750 g of water at 20 C is poured into the kettle. When the kettle is switched on, it takes 2.0 minutes for the water to start boiling. In a further 7.0 minutes,
More informationThermodynamics 2013/2014, lecturer: Martin Zápotocký
Thermodynamics 2013/2014, lecturer: Martin Zápotocký 2 lectures: 1. Thermodynamic processes, heat and work, calorimetry, 1 st and 2 nd law of thermodynamics 2. Entropy, thermodynamic potentials, nonequilibrium
More informationHeat and Temperature
Heat and Temperature Temperature What does temperature have to do with energy? What three temperature scales are commonly used? What makes things feel hot or cold? Intro: Discussion A person from Seattle
More information18.13 Review & Summary
5/2/10 10:04 PM Print this page 18.13 Review & Summary Temperature; Thermometers Temperature is an SI base quantity related to our sense of hot and cold. It is measured with a thermometer, which contains
More informationPROGRAM OF PHYSICS. Lecturer: Dr. DO Xuan Hoi Room A
PROGRAM OF PHYSICS Lecturer: Dr. DO Xuan Hoi Room A1. 503 E-mail : dxhoi@hcmiu.edu.vn PHYSICS 2 (FLUID MECHANICS AND THERMAL PHYSICS) 02 credits (30 periods) Chapter 1 Fluid Mechanics Chapter 2 Heat, Temperature
More informationFigure 1.1. Relation between Celsius and Fahrenheit scales. From Figure 1.1. (1.1)
CHAPTER I ELEMENTS OF APPLIED THERMODYNAMICS 1.1. INTRODUCTION. The Air Conditioning systems extract heat from some closed location and deliver it to other places. To better understanding the principles
More informationPHYSICS HIGHER LEVEL
*P16* PRE-LEAVING CERTIFICATE EXAMINATION, 2011 PHYSICS HIGHER LEVEL TIME: 3 HOURS Answer three questions from section A and five questions from section B. Page 1 of 9 SECTION A (120 marks) Answer three
More informationLecture 13 Chapter 18 Temperature, Heat, and the First Law of Thermodynamics
Lecture 13 Chapter 18 Temperature, Heat, and the First Law of Thermodynamics Lecture 13 Chapter 18 Temperature, Heat, and the First Law of Thermodynamics Temperature and Thermal Equilibrium Linear Expansion
More informationHeat & Temperature. Grade 7 Science - Unit 2 Pgs
Heat & Temperature Grade 7 Science - Unit 2 Pgs 104-225 Temperature P Temperature is the measure of how much heat is in a substance. P Temperature is measured in degrees Celcius ( C) P It is difficult
More informationIntroduction to thermodynamics
Chapter 6 Introduction to thermodynamics Topics First law of thermodynamics Definitions of internal energy and work done, leading to du = dq + dw Heat capacities, C p = C V + R Reversible and irreversible
More informationChapter 18. Temperature, Heat, and the First Law of Thermodynamics Temperature
Chapter 18 Temperature, Heat, and the First Law of Thermodynamics 18.2 Temperature 18.3: The Zeroth aw of Thermodynamics If bodies A and B are each in thermal equilibrium with a third body T, then A and
More informationThermometry And Thermal Expansion
Thermometry And Thermal Expansion 1. Define heat (a) on conventional basis (b) on the basis of kinetic model. Ans. (a) On the conventional basis heat is the from of energy which causes in us sensation
More informationTheory and Design for Mechanical Measurements
Theory and Design for Mechanical Measurements Third Edition Richard S. Figliola Clemson University Donald E. Beasley Clemson University John Wiley & Sons, Inc. New York / Chichester / Weinheim / Brisbane
More information14CH406. Chemical Engineering Scheme of Valuation Process Instrumentation Maximum : 60 Marks (1X12 = 12 Marks) Answer ONE question from each unit.
April, 2018 Fourth Semester Time: Three Hours Answer Question No.1 compulsorily. II/IV B.Tech. (Regular/Supplementary) DEGREE EXAMINATION 14CH406 Chemical Engineering Scheme of Valuation Process Instrumentation
More informationConceptual Physics Fundamentals
Conceptual Physics Fundamentals Chapter 8: TEMPERATURE, HEAT, AND THERMODYNAMICS This lecture will help you understand: Temperature Absolute Zero Internal Energy Heat Quantity of Heat The Laws of Thermodynamics
More informationThis book is under copyright to A-level Physics Tutor. However, it may be distributed freely provided it is not sold for profit.
2 This book is under copyright to A-level Physics Tutor. However, it may be distributed freely provided it is not sold for profit. CONTENTS thermometry what is temperature?, fixed points, Kelvin (Absolute),
More informationModule 3 - Thermodynamics. Thermodynamics. Measuring Temperatures. Temperature and Thermal Equilibrium
Thermodynamics From the Greek thermos meaning heat and dynamis meaning power is a branch of physics that studies the effects of changes in temperature, pressure, and volume on physical systems at the macroscopic
More informationTemperature and Heat. Chapter 17. PowerPoint Lectures for University Physics, Twelfth Edition Hugh D. Young and Roger A. Freedman
Chapter 17 Temperature and Heat PowerPoint Lectures for University Physics, Twelfth Edition Hugh D. Young and Roger A. Freedman Lectures by James Pazun Goals for Chapter 17 To delineate the three different
More informationTemperature. 3
Temperature In 1848, Sir William Thomson (Lord Kelvin) stated the zero principle of dynamics. This principle enabled him to define thermodynamic temperature and to establish an objective method of measuring
More informationTemperature measurement
emperature measurement BASICS Interest in emperature measurements appeared definitively later as respect to other quantities. emperature is an intensive quantity (a quantity strictly correlated to temperature
More informationAnswer three questions from Section A and five questions from Section B.
L.35 PRE-LEAVING CERTIFICATE EXAMINATION, 2016 PHYSICS ORDINARY LEVEL TIME 3 HOURS Answer three questions from Section A and five questions from Section B. Relevant data are listed in the Formulae and
More informationPart Number Range Accuracy Printing WP * Probe Special User LDC with Page Logging included Feature Cal Backlight
Table of Contents Comparison Chart Introduction Temperature Indicators & Controllers Portable Infrared Printing/Logging Page O2 O3 O10 O14 O30 O33 O1 Part Number Range Accuracy Printing WP * Probe Special
More informationAcademic Year First Term. Science Revision sheets PHYSICS
Academic Year 2016-2017 First Term Science Revision sheets PHYSICS Name: Grade: 10 Date: Section: (A) Science Practice : Q1: Choose the letter of the choice that best answer the questions: 1. What term
More informationSlide 1 / 67. Slide 2 / 67. 8th Grade. Thermal Energy Study Guide Slide 3 / 67. Thermal Energy. Study Guide.
Slide 1 / 67 Slide 2 / 67 8th Grade Thermal Energy Study Guide 2015-10-09 www.njctl.org Slide 3 / 67 Thermal Energy Study Guide www.njctl.org Slide 4 / 67 Part 1 Define the following terms and/or concepts
More informationPut sufficient ice cubes into water (1 M) and wait for equilibrium (both exist) (1 M)
NAME : F.5 ( ) Marks: /70 FORM FOUR PHYSICS REVISION TEST on HEAT Allowed: 70 minutes This paper consists of two sections. Section A (50 marks) consists of the structure-type questions, and Section B (20
More information8th Grade. Thermal Energy Study Guide.
1 8th Grade Thermal Energy Study Guide 2015 10 09 www.njctl.org 2 Thermal Energy Study Guide www.njctl.org 3 Part 1 Define the following terms and/or concepts 4 1 Temperature 5 2 Kinetic Energy 6 3 Thermal
More informationQ11: WHAT IS A MEANT GOOD ELECTRICAL CONNECTION?
Q1. How to check for zero error in a: (i) Vernier caliper (ii) Micrometer screw gauge (iii) Meter rule (iv) Stopwatch Ans: (i) Close the jaws of the vernier caliper fully. When the zeros of both MAIN SCALE
More informationUnit 11: Temperature and heat
Unit 11: Temperature and heat 1. Thermal energy 2. Temperature 3. Heat and thermal equlibrium 4. Effects of heat 5. Transference of heat 6. Conductors and insulators Think and answer a. Is it the same
More informationWe call the characteristic of a system that determines how much its temperature will change heat capacity.
3/3 Measuring Heat If all we do is add heat to a system its temperature will rise. How much the temperature rises depends on the system. We call the characteristic of a system that determines how much
More informationTemperature Measurement
Temperature Measurement Temperature is one of the most common measurements What is Temperature? Intuitively understood as sensation of hot/cold Early Researchers: Galileo (1564-1642) Newton (1642-1727)
More informationComparison of sensors for the measurement of temperature with (small) UAV/RPA
Comparison of sensors for the measurement of temperature with (small) UAV/RPA Norman Wildmann, Jens Bange Center for Applied Geosciences, Eberhard Karls University Tübingen 19 February 2013, Palma de Mallorca
More informationSome Vocabulary. Chapter 10. Zeroth Law of Thermodynamics. Thermometers
Chapter 0 Some Vocabulary Thermal Physics, Temperature and Heat Thermodynamics: Study of energy transfers (engines) Changes of state (solid, liquid, gas...) Heat: Transfer of microscopic thermal energy
More informationAcademic Year 2016-2017 First Term Science Revision sheets PHYSICS ( Answer key ) Name: Grade: 10 Date: Section: (A) Science Practice : Q1: Choose the letter of the choice that best answer the questions:
More informationPAPER 2 THEORY QUESTIONS
PAPER 2 THEORY QUESTIONS 1 Fig. 1.1 shows the arrangement of atoms in a solid block. Fig. 1.1 (a) End X of the block is heated. Energy is conducted to end Y, which becomes warm. (i) Explain how heat is
More informationRoll No. :... Invigilator s Signature :.. CS/B.Tech (EIE)/SEM-5/EI-501/ INDUSTRIAL INSTRUMENTATION II
Name : Roll No. :.... Invigilator s Signature :.. CS/B.Tech (EIE)/SEM-5/EI-501/2011-12 2011 INDUSTRIAL INSTRUMENTATION II Time Allotted : 3 Hours Full Marks : 70 The figures in the margin indicate full
More informationPhysics 123 Thermodynamics Review
Physics 3 Thermodynamics Review I. Definitions & Facts thermal equilibrium ideal gas thermal energy internal energy heat flow heat capacity specific heat heat of fusion heat of vaporization phase change
More informationCHAPTER 4 THERMAL CONDUCTIVITY AND VISCOSITY MEASUREMENTS
50 CHAPTER 4 THERMAL CONDUCTIVITY AND VISCOSITY MEASUREMENTS 4.1 INTRODUCTION In the development of any energy-efficient heat transfer fluids for enhanced heat transfer performance, in practical applications,
More informationGRADE 11F: Physics 2. UNIT 11FP.2 11 hours. Temperature and heat. Resources. About this unit. Previous learning. Expectations
GRADE 11F: Physics 2 Temperature and heat UNIT 11FP.2 11 hours About this unit This unit is the second of five units on physics for Grade 11 foundation. The unit is designed to guide your planning and
More informationWhat does temperature have to do with energy? What three temperature scales are commonly used? What makes things feel hot or cold?
Heat and Temperature Section 1: Temperature What does temperature have to do with energy? What three temperature scales are commonly used? What makes things feel hot or cold? 1 Intro: Discussion A person
More informationINSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad
INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad -500 043 MECHANICAL ENGINEERING TUTORIAL QUESTION BANK Name : INSTRUMENTATION AND CONTROL SYSTEMS Code : A70343 Class : IV B. Tech
More information4. Thermometry. Temperature and Heat Flow Temperature Scales Thermometers
4. Thermometry Measuring temperature by sensation is very imprecise. That is why we need a temperature scale and a thermometer to measure temperature more accurately. Temperature and Heat Flow Temperature
More informationMATTER AND HEAT. Chapter 4 OUTLINE GOALS
Chapter 4 MATTER AND HEAT OUTLINE Temperature and Heat 4.1 Temperature 4.2 Heat 4.3 Metabolic Energy Fluids 4.4 Density 4.5 Pressure 4.6 Buoyancy 4.7 The Gas Laws Kinetic Theory of Matter 4.8 Kinetic Theory
More informationEA-10/13. EA Guidelines on the Calibration of Temperature Block Calibrators. Publication Reference PURPOSE
Publication Reference EA-10/13 EA Guidelines on the Calibration of Temperature Block Calibrators PURPOSE This document been produced by EA to improve the harmonisation in the calibration of temperature
More informationChapter 2 Heat, Temperature and the First Law of Thermodynamics
Chapter 2 Heat, Temperature and the First Law of Thermodynamics 2.1. Temperature and the Zeroth Law of Thermodynamics 2.2. Thermal Expansion 2.3. Heat and the Absorption of Heat by Solids and Liquids 2.4.
More information