Initial Stress Calculations
|
|
- Gwen Gibbs
- 6 years ago
- Views:
Transcription
1 Initial Stress Calculations The following are the initial hand stress calculations conducted during the early stages of the design process. Therefore, some of the material properties as well as dimensions are not up to date with the device design. Thread Calculations Adequate pressure generation is a key criterion in the design of the clamp. In order to ensure that the clamp exerts the necessary force on the bell, calculations must be made to predict the amount of force that will be generated from the threads in the bell. These equations can be used either to calculate the forced generated, or to solve for the needed thread angle in order to generate a given load. Firstly, the given specifications for loading, as well as thread dimensions, will be defined. Force necessary for threads to generate Force exerted on nut This value was determined based upon the average force that a human hand can generate by turning a knob. There is a great deal of variation in this number, so a conservatively low value was used for the force. Diameter of thread Length of lever arm (1/2 diameter of turning nut) coefficient of friction coefficient of friction of collar diameter of collar
2 Angle of acme thread (constant for all acme threads) Figure 1 Acme Thread Diagram Using the defined variables, the calculations can be made in order to find unknown terms. Applied torque (The torque applied to the screw by the defined hand force) [1, p. 118] (eq. 1) Using the governing equation, listed below, an expression for the lead (L) can be derived for acme threads with the given inputs, listed above. [2, p. 869] ( (eq. 2) The above equation can be rearranged into:
3 Then rearranged into: Finally, the maximum lead (L) can be isolated in the equation below With given geometry, and loading conditions, the lead must be less than or equal to 19.1 mm. This criteria will most definitely be satisfied. The actual lead used is 1.27 mm, less than 7% of the maximum possible lead. Calculations must be made to ensure that the screw will not back out. Due to the fact that the clamp will be tightened and then left to set for several minutes, it is crucial that the screw does not back off at all, since that would have a catastrophic effect upon the pressure distribution, as well as negatively effecting adequate pressure generation. Figure 2 - Thread Diagram [2, p. 869] Define lead (L) for thread Additionally, using the previously defined L, the minimum coefficient of friction needed in order to maintain the self-locking criteria, is defined as: [2, p. 870] (eq. 3)
4 The coefficient of friction criteria will be met, as the estimated coefficient of friction will be approximately 0.15, 7.5 times larger than the minimum criteria. In order to ensure no back off for the thread, the following relationship must be met [2, p. 870] (eq. 4) Clearly, there will be no issue designing the actual device to meet the maximum requirement. In order to ensure that the threads will not have a shear failure, which would be catastrophic to the clamp, the following equations must be satisfied. The stress analysis of the threads will take into account material properties, something that is very important due to the utilization of unique materials in the construction of the clamp. Firstly, a list of variables used in the following calculations will be shown (applied load) (basic diameter) (thread pitch) (ultimate strength of material) (height, or thickness, of nut) (area of rod) [1, p. 656] (eq. 5) (area of thread) [1, p. 656] (eq. 6) (minimum thread engagement) [3] (eq. 7) (stress in rod) [2, p. 31] (eq. 8) (FOS of loaded rod) [2, p. 260] (eq. 9)
5 Shear failure of the threads was also analyzed, since this type of failure would be a catastrophic failure for the device. Due to the fact that the diameter of the threads is less than 25.4 mm, combined with the fact that the threads are a standard Acme thread, the minimum nut length required to ensure that the threads will have strip strength in excess of the screw s tensile strength is mm [3, p. 876]. Since the defined nut height is 12.7 mm, it can be concluded that the threads will not fail in shear. Bell calculations Due to the complexity of the loading on the bell, which is exacerbated by the complexity of the geometry, the only truly accurate method for conducting stress analysis on the bell is through a finite element analysis. Since the finite element analysis will not be complete until the second semester, the dimensioning and material selection for the prototype bell will be based upon the results from competitive product analysis. In addition to failure analysis, the appropriate material hardness must be achieved, in order to ensure the bell does not have surface deformation that could affect the even pressure distribution. By using design requirements from competitive analysis, the initial prototype can be created, and then the results from the finite element analysis can be used to optimize and finalize the design. Base Plate Deflection Calculations The base plate and bell pushing against each other cause a pressure distribution on the skin. As this system is basically a clamp, there is an upward force at the center of the plate, which causes deflection. The maximum deflection will be located at the center of the plate. As this deflection increases, the pressure distribution on the skin will begin to vary. The less uniform this pressure distribution becomes, the more likely it is for incomplete hemostasis, complicating the surgery. To prevent this, the base plate deflection must be minimized as much as possible. The deflection is a function of the design, the force applied, and the modulus of elasticity of the material. For the initial deflection calculations, some simplifying assumptions will be made. It will be assumed that the base plate can be modeled by two different beams attached to each other (see descriptive figures, below). The first will be attached to a rigid post. The only load on this first beam will be the reaction forces from the second beam. One end of the second beam will be attached to the first beam, while the other end will be hanging in space. The second beam will experience the reaction load of the pressure distribution over its entire length.
6 Figure 3 - Side view of actual design Figure 4 - Side view of simplified model Figure 3, above, is picture of the base plate from the side view. Figure 4, above, is the simplified design. The smallest dimensions from the actual model were used to define the simplified model. Since the smallest values are used, a factor of safety is already built into the calculations. Figure 5 - Top view of actual design Figure 6 - Top view of simplified model
7 Figure 5, above, is the actual base plate, orientated so the view is from the top. Figure 6, above, is the simplified design. The dimensions of the simplified design are the thinnest sections of the actual design, thus maintaining a conservative factor of safety. The dimensions labeled in the figures are the dimensions that will be used throughout the analysis of the base plate. Using the simplified design, the base plate deflection is calculated below. Bending of beam 1 [2, p. 996] (eq. 11) Bending of beam 2 [2, p. 996] (eq. 12) Moment of inertia [4] (eq. 13) Where F is the force at the end of the beam L is the length of the beam E is the modulus of elasticity (material constant) I is the moment of inertia (design constant) W is the load (F) distributed across the beam B is the base length of the beam H is the height of the beam These equations will be slightly conservative since the smallest dimensions are used. Therefore, a factor of safety is already built into the calculations. Table 1 - Base plate dimensions and properties Beam 1 Beam 2 Base mm 8.13 mm Height 3.05 mm 8.13 mm Length 3.81 mm mm Properties (both bars) E = 10, MPa Force = 1,290.0 N The loading has been calculated by the force applied by the screw. As E is a material constant, it will change as different materials are tested. This value is most likely to be the variable modified to output the desired maximum deflection
8 Using a value of 10, MPa for the modulus of elasticity, the final resulting maximum deflection in the base plate is 0.12 mm. Base Plate Factor of Safety As a check to make sure the device does not break, the factor of safety is also found for both of the beams. The smallest factor of safety for the two beams will be roughly that of the base plate, and as such, should be a good comparison. For these calculations, the base plate was modeled the same way as the max deflection calculations. Figures 11 through 14 represent the assumptions made and the dimensions used for the following calculations. Stress in beams [2, p. 156] (eq. 14) Where σ is the stress M is the maximum moment c is half the height I is the moment of inertia For beam 1 the max moment will be calculated by [2, p. 996] For beam 2 the max moment will be calculated by [2, p. 996] (eq. 15) (eq. 16) Where F is the point force downward L is the length of the beam w is the loading per unit length As the two beams are the same beams for which the deflection was found, the dimensions will be the same. These can be found in table 1, above. Once the max moment is obtained the factor of safety can be found using the following equation [2, p. 260] (eq. 17)
9 Where Sfa is the factor of safety Sy is the ultimate shear stress σmax is the maximum stress found of either beam. When the numbers are inserted into these equations, the maximum stress calculated to be MPa. Using MPa as the ultimate shear strength, the factor of safety found for the base plate is A factor of safety of 1.5 is more than adequate for a single use device. Therefore, under given loading conditions, the base plate will not fail. Column Factor of Safety The factor of safety for the columns must be calculated, to ensure that the device does not break while it is being used. As the columns are of equal diameter over their entire length, they will break at the point where the curvature, and stress concentration, is the greatest. The dimensions of the beam where the curvature is the greatest are as follows Table 2 - Column dimensions Outer radius of curvature of mm beam Inner radius of curvature of beam 5.72 mm Diameter of column mm D = mm Figure 7 - Cross section of column
10 Figure 8 - Side view of column curve Figure 8, above, depicts the curved portion of the beam, where the beam is most likely to fail. The three arrows show the 3 radiuses of curvature, the smallest being the inner, the middle the average, and the largest is the outer radius of curvature. The following equations can be used to find the factor of safety for curved beams. Several of the constants needed in the equations are and e. These constants are calculated below. [4], the area of the cross section, co, ci, (eq. 18) (eq. 19) (eq. 20) (eq. 21) (eq. 22) Where ro is the outer radius of curvature ri is the inner radius of curvature d is the diameter of the column rc is the average radius of curvature The stress along the inner and outer radius can now be found using the following equations. [4]
11 (eq. 23) (eq. 24) To find the factor of safety, the ultimate tensile strength for the material will also be needed. This is a known constant, and can be determined from material constant tables. The factor of safety can be found for the columns using the equation below. [4] (eq. 25) When the numbers are inserted into the equations, the maximum stress within the beams is calculated to be MPa. With this max stress, and using MPa as the ultimate tensile strength, the resulting factor of safety for the base plate is As seen, the columns have a factor of safety well above 1. From this, it can be concluded that columns of the device will not fail when the target load is applied to the device. Column Deflection There are two straight sections to each of the columns; these are the sections that will analyzed for deflection. The vertical deflection in both strait sections of the column will be found and added together. Despite one of the sections being angled heavily from vertical, this angle was neglected in order to add a conservative factor of safety. Figure 9 - Side view of the column
12 The equations used to find the approximate value for these deflections are as follows. [2, p. 31] (eq. 26) (eq. 27) (eq. 28) Where σ is the stress P is the load A is the area ε is the strain E is the modulus of elasticity l is the length after the load is applied lo is the length before the load is applied Using a modulus of Elasticity of 10, MPa, the vertical elongation of the column is calculated to be 0.04 mm. Material Selection At the time that these initial hand calculations were conducted, a material had not been selected for the device. Therefore, in order to complete the analysis material properties were chosen. The ultimate tensile strength was set at MPa and the modulus of elasticity was set at 10, MPa. However, these properties can be modified according to the results from the analysis. If a material is used that has lower material property values than these, the device will be more likely to have a deflection greater than desired. In addition the device will also have a factor of safety below the desired factor of safety of 1.5. As such, these are the lowest material property values that should be used. Materials with properties above these values can be used, since they will only improve upon the already acceptable deflections and factor of safety. However, material cost must be taken into consideration, limiting some high strength materials.
13 Works Cited [1] R. C. Hibbeler, "Chapter 4," in Statics, Upper Saddle River, Pearson, [2] R. Norton, Machine design an integrated approach, 4th ed., Upper Saddle River, New Jersey: Prentice Hall, 2011, p [3] "RoyMech," [Online]. Available: [Accessed 26th November 2013] [4] "Curved beams, derivation of stress equations," [Online]. Available: [Accessed 15 November 2013].
Mechanical Engineering Ph.D. Preliminary Qualifying Examination Solid Mechanics February 25, 2002
student personal identification (ID) number on each sheet. Do not write your name on any sheet. #1. A homogeneous, isotropic, linear elastic bar has rectangular cross sectional area A, modulus of elasticity
More informationStress Analysis Lecture 3 ME 276 Spring Dr./ Ahmed Mohamed Nagib Elmekawy
Stress Analysis Lecture 3 ME 276 Spring 2017-2018 Dr./ Ahmed Mohamed Nagib Elmekawy Axial Stress 2 Beam under the action of two tensile forces 3 Beam under the action of two tensile forces 4 Shear Stress
More informationThe University of Melbourne Engineering Mechanics
The University of Melbourne 436-291 Engineering Mechanics Tutorial Four Poisson s Ratio and Axial Loading Part A (Introductory) 1. (Problem 9-22 from Hibbeler - Statics and Mechanics of Materials) A short
More informationArberi Ferraj. Wentworth Institute of Technology. Design of Machine Elements MECH 420
P a g e 1 Arberi Ferraj Wentworth Institute of Technology Design of Machine Elements MECH 420 P a g e 2 1. Executive Summary A scissor car jack was designed and must be reverse-engineered in order to discover
More informationMAAE 2202 A. Come to the PASS workshop with your mock exam complete. During the workshop you can work with other students to review your work.
It is most beneficial to you to write this mock final exam UNDER EXAM CONDITIONS. This means: Complete the exam in 3 hours. Work on your own. Keep your textbook closed. Attempt every question. After the
More informationMECHANICS LAB AM 317 EXP 4 TORSION OF CIRCULAR RODS
MECHANICS LAB AM 317 EXP 4 TORSION OF CIRCULAR RODS I. OBJECTIVES I.1 To become familiar with torsion tests of rods with solid circular cross sections. I.2 To observe the relation between shear stress
More informationPDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [ ] Introduction, Fundamentals of Statics
Page1 PDDC 1 st Semester Civil Engineering Department Assignments of Mechanics of Solids [2910601] Introduction, Fundamentals of Statics 1. Differentiate between Scalar and Vector quantity. Write S.I.
More informationAERO 214. Lab II. Measurement of elastic moduli using bending of beams and torsion of bars
AERO 214 Lab II. Measurement of elastic moduli using bending of beams and torsion of bars BENDING EXPERIMENT Introduction Flexural properties of materials are of interest to engineers in many different
More informationSamantha Ramirez, MSE. Stress. The intensity of the internal force acting on a specific plane (area) passing through a point. F 2
Samantha Ramirez, MSE Stress The intensity of the internal force acting on a specific plane (area) passing through a point. Δ ΔA Δ z Δ 1 2 ΔA Δ x Δ y ΔA is an infinitesimal size area with a uniform force
More informationMECHANICS LAB AM 317 EXP 3 BENDING STRESS IN A BEAM
MECHANICS LAB AM 37 EXP 3 BENDING STRESS IN A BEAM I. OBJECTIVES I. To compare the experimentally determined stresses in a beam with those predicted from the simple beam theory (a.k.a. Euler-Bernoull beam
More informationSample Question Paper
Scheme I Sample Question Paper Program Name : Mechanical Engineering Program Group Program Code : AE/ME/PG/PT/FG Semester : Third Course Title : Strength of Materials Marks : 70 Time: 3 Hrs. Instructions:
More informationUnit Workbook 1 Level 4 ENG U8 Mechanical Principles 2018 UniCourse Ltd. All Rights Reserved. Sample
Pearson BTEC Levels 4 Higher Nationals in Engineering (RQF) Unit 8: Mechanical Principles Unit Workbook 1 in a series of 4 for this unit Learning Outcome 1 Static Mechanical Systems Page 1 of 23 1.1 Shafts
More informationME325 EXAM I (Sample)
ME35 EXAM I (Sample) NAME: NOTE: COSED BOOK, COSED NOTES. ONY A SINGE 8.5x" ORMUA SHEET IS AOWED. ADDITIONA INORMATION IS AVAIABE ON THE AST PAGE O THIS EXAM. DO YOUR WORK ON THE EXAM ONY (NO SCRATCH PAPER
More informationStructural Metals Lab 1.2. Torsion Testing of Structural Metals. Standards ASTM E143: Shear Modulus at Room Temperature
Torsion Testing of Structural Metals Standards ASTM E143: Shear Modulus at Room Temperature Purpose To determine the shear modulus of structural metals Equipment Tinius-Olsen Lo-Torq Torsion Machine (figure
More informationCE 221: MECHANICS OF SOLIDS I CHAPTER 1: STRESS. Dr. Krisada Chaiyasarn Department of Civil Engineering, Faculty of Engineering Thammasat university
CE 221: MECHANICS OF SOLIDS I CHAPTER 1: STRESS By Dr. Krisada Chaiyasarn Department of Civil Engineering, Faculty of Engineering Thammasat university Agenda Introduction to your lecturer Introduction
More informationMEMS Project 2 Assignment. Design of a Shaft to Transmit Torque Between Two Pulleys
MEMS 029 Project 2 Assignment Design of a Shaft to Transmit Torque Between Two Pulleys Date: February 5, 206 Instructor: Dr. Stephen Ludwick Product Definition Shafts are incredibly important in order
More informationMarch 24, Chapter 4. Deflection and Stiffness. Dr. Mohammad Suliman Abuhaiba, PE
Chapter 4 Deflection and Stiffness 1 2 Chapter Outline Spring Rates Tension, Compression, and Torsion Deflection Due to Bending Beam Deflection Methods Beam Deflections by Superposition Strain Energy Castigliano
More information2012 MECHANICS OF SOLIDS
R10 SET - 1 II B.Tech II Semester, Regular Examinations, April 2012 MECHANICS OF SOLIDS (Com. to ME, AME, MM) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~
More informationMECE 3321 MECHANICS OF SOLIDS CHAPTER 1
MECE 3321 MECHANICS O SOLIDS CHAPTER 1 Samantha Ramirez, MSE WHAT IS MECHANICS O MATERIALS? Rigid Bodies Statics Dynamics Mechanics Deformable Bodies Solids/Mech. Of Materials luids 1 WHAT IS MECHANICS
More informationD e s i g n o f R i v e t e d J o i n t s, C o t t e r & K n u c k l e J o i n t s
D e s i g n o f R i v e t e d J o i n t s, C o t t e r & K n u c k l e J o i n t s 1. Design of various types of riveted joints under different static loading conditions, eccentrically loaded riveted joints.
More informationD : SOLID MECHANICS. Q. 1 Q. 9 carry one mark each. Q.1 Find the force (in kn) in the member BH of the truss shown.
D : SOLID MECHANICS Q. 1 Q. 9 carry one mark each. Q.1 Find the force (in kn) in the member BH of the truss shown. Q.2 Consider the forces of magnitude F acting on the sides of the regular hexagon having
More informationMechanics of Materials Primer
Mechanics of Materials rimer Notation: A = area (net = with holes, bearing = in contact, etc...) b = total width of material at a horizontal section d = diameter of a hole D = symbol for diameter E = modulus
More informationChapter Objectives. Design a beam to resist both bendingand shear loads
Chapter Objectives Design a beam to resist both bendingand shear loads A Bridge Deck under Bending Action Castellated Beams Post-tensioned Concrete Beam Lateral Distortion of a Beam Due to Lateral Load
More informationPurpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on Exam 3.
ES230 STRENGTH OF MTERILS Exam 3 Study Guide Exam 3: Wednesday, March 8 th in-class Updated 3/3/17 Purpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on
More informationLecture 15 Strain and stress in beams
Spring, 2019 ME 323 Mechanics of Materials Lecture 15 Strain and stress in beams Reading assignment: 6.1 6.2 News: Instructor: Prof. Marcial Gonzalez Last modified: 1/6/19 9:42:38 PM Beam theory (@ ME
More informationStresses in Curved Beam
Stresses in Curved Beam Consider a curved beam subjected to bending moment M b as shown in the figure. The distribution of stress in curved flexural member is determined by using the following assumptions:
More information[8] Bending and Shear Loading of Beams
[8] Bending and Shear Loading of Beams Page 1 of 28 [8] Bending and Shear Loading of Beams [8.1] Bending of Beams (will not be covered in class) [8.2] Bending Strain and Stress [8.3] Shear in Straight
More informationDesign against fluctuating load
Design against fluctuating load In many applications, the force acting on the spring is not constants but varies in magnitude with time. The valve springs of automotive engine subjected to millions of
More informationR13. II B. Tech I Semester Regular Examinations, Jan MECHANICS OF SOLIDS (Com. to ME, AME, AE, MTE) PART-A
SET - 1 II B. Tech I Semester Regular Examinations, Jan - 2015 MECHANICS OF SOLIDS (Com. to ME, AME, AE, MTE) Time: 3 hours Max. Marks: 70 Note: 1. Question Paper consists of two parts (Part-A and Part-B)
More informationKINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK. Subject code/name: ME2254/STRENGTH OF MATERIALS Year/Sem:II / IV
KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK Subject code/name: ME2254/STRENGTH OF MATERIALS Year/Sem:II / IV UNIT I STRESS, STRAIN DEFORMATION OF SOLIDS PART A (2 MARKS)
More informationMechanical Design in Optical Engineering
OPTI Buckling Buckling and Stability: As we learned in the previous lectures, structures may fail in a variety of ways, depending on the materials, load and support conditions. We had two primary concerns:
More information3 Hours/100 Marks Seat No.
*17304* 17304 14115 3 Hours/100 Marks Seat No. Instructions : (1) All questions are compulsory. (2) Illustrate your answers with neat sketches wherever necessary. (3) Figures to the right indicate full
More informationSolution: The moment of inertia for the cross-section is: ANS: ANS: Problem 15.6 The material of the beam in Problem
Problem 15.4 The beam consists of material with modulus of elasticity E 14x10 6 psi and is subjected to couples M 150, 000 in lb at its ends. (a) What is the resulting radius of curvature of the neutral
More informationDownloaded from Downloaded from / 1
PURWANCHAL UNIVERSITY III SEMESTER FINAL EXAMINATION-2002 LEVEL : B. E. (Civil) SUBJECT: BEG256CI, Strength of Material Full Marks: 80 TIME: 03:00 hrs Pass marks: 32 Candidates are required to give their
More informationSTRENGTH OF MATERIALS-I. Unit-1. Simple stresses and strains
STRENGTH OF MATERIALS-I Unit-1 Simple stresses and strains 1. What is the Principle of surveying 2. Define Magnetic, True & Arbitrary Meridians. 3. Mention different types of chains 4. Differentiate between
More informationMECHANICS OF MATERIALS
2009 The McGraw-Hill Companies, Inc. All rights reserved. Fifth SI Edition CHAPTER 3 MECHANICS OF MATERIALS Ferdinand P. Beer E. Russell Johnston, Jr. John T. DeWolf David F. Mazurek Torsion Lecture Notes:
More informationI certify that I have not given unauthorized aid nor have I received aid in the completion of this exam.
NAME: ME 270 Fall 2012 Examination No. 3 - Makeup Please review the following statement: Group No.: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam.
More information4. SHAFTS. A shaft is an element used to transmit power and torque, and it can support
4. SHAFTS A shaft is an element used to transmit power and torque, and it can support reverse bending (fatigue). Most shafts have circular cross sections, either solid or tubular. The difference between
More informationExperiment Two (2) Torsional testing of Circular Shafts
Experiment Two (2) Torsional testing of Circular Shafts Introduction: Torsion occurs when any shaft is subjected to a torque. This is true whether the shaft is rotating (such as drive shafts on engines,
More informationMaterials: engineering, science, processing and design, 2nd edition Copyright (c)2010 Michael Ashby, Hugh Shercliff, David Cebon.
Modes of Loading (1) tension (a) (2) compression (b) (3) bending (c) (4) torsion (d) and combinations of them (e) Figure 4.2 1 Standard Solution to Elastic Problems Three common modes of loading: (a) tie
More informationTuesday, February 11, Chapter 3. Load and Stress Analysis. Dr. Mohammad Suliman Abuhaiba, PE
1 Chapter 3 Load and Stress Analysis 2 Chapter Outline Equilibrium & Free-Body Diagrams Shear Force and Bending Moments in Beams Singularity Functions Stress Cartesian Stress Components Mohr s Circle for
More informationJeff Brown Hope College, Department of Engineering, 27 Graves Pl., Holland, Michigan, USA UNESCO EOLSS
MECHANICS OF MATERIALS Jeff Brown Hope College, Department of Engineering, 27 Graves Pl., Holland, Michigan, USA Keywords: Solid mechanics, stress, strain, yield strength Contents 1. Introduction 2. Stress
More informationCHAPTER THREE SYMMETRIC BENDING OF CIRCLE PLATES
CHAPTER THREE SYMMETRIC BENDING OF CIRCLE PLATES * Governing equations in beam and plate bending ** Solution by superposition 1.1 From Beam Bending to Plate Bending 1.2 Governing Equations For Symmetric
More informationMECHANICS OF MATERIALS
MM 210 MECHANICS OF MATERIALS 2012-2013 1 1.INTRODUCTION TO MECHANICS OF MATERIALS WHAT IS MECHANICS OF MATERIALS? Mechanics is the physical science that deals with the conditions of rest or motion of
More information2014 MECHANICS OF MATERIALS
R10 SET - 1 II. Tech I Semester Regular Examinations, March 2014 MEHNIS OF MTERILS (ivil Engineering) Time: 3 hours Max. Marks: 75 nswer any FIVE Questions ll Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~~~~
More informationMembers Subjected to Torsional Loads
Members Subjected to Torsional Loads Torsion of circular shafts Definition of Torsion: Consider a shaft rigidly clamped at one end and twisted at the other end by a torque T = F.d applied in a plane perpendicular
More informationDesign and Analysis of Adjustable Inside Diameter Mandrel for Induction Pipe Bender
International Journal of Engineering Trends and Technology (IJETT) Volume0Number - Apr 0 Design and Analysis of Adjustable Inside Diameter Mandrel for Induction Pipe Bender S.Nantha Gopan, M.Gowtham J.Kirubakaran
More informationBE Semester- I ( ) Question Bank (MECHANICS OF SOLIDS)
BE Semester- I ( ) Question Bank (MECHANICS OF SOLIDS) All questions carry equal marks(10 marks) Q.1 (a) Write the SI units of following quantities and also mention whether it is scalar or vector: (i)
More informationMeasurement of Bone Strength and Stiffness using 3-Point Bending
BME 315 Biomechanics, U. Wisconsin Adapted by R. Lakes from D. Thelen and C. Decker, 09, adapted from Lakes 06 Experimental Details I. Laboratory equipment The load frame that we will use to perform our
More informationMECHANICS OF MATERIALS Sample Problem 4.2
Sample Problem 4. SOLUTON: Based on the cross section geometry, calculate the location of the section centroid and moment of inertia. ya ( + Y Ad ) A A cast-iron machine part is acted upon by a kn-m couple.
More informationQUESTION BANK DEPARTMENT: CIVIL SEMESTER: III SUBJECT CODE: CE2201 SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A
DEPARTMENT: CIVIL SUBJECT CODE: CE2201 QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State
More informationCOURSE TITLE : APPLIED MECHANICS & STRENGTH OF MATERIALS COURSE CODE : 4017 COURSE CATEGORY : A PERIODS/WEEK : 6 PERIODS/ SEMESTER : 108 CREDITS : 5
COURSE TITLE : APPLIED MECHANICS & STRENGTH OF MATERIALS COURSE CODE : 4017 COURSE CATEGORY : A PERIODS/WEEK : 6 PERIODS/ SEMESTER : 108 CREDITS : 5 TIME SCHEDULE MODULE TOPICS PERIODS 1 Simple stresses
More informationINTRODUCTION (Cont..)
INTRODUCTION Name : Mohamad Redhwan Abd Aziz Post : Lecturer @ DEAN CENTER OF HND STUDIES Subject : Solid Mechanics Code : BME 2033 Room : CENTER OF HND STUDIES OFFICE H/P No. : 019-2579663 W/SITE : Http://tatiuc.edu.my/redhwan
More informationNORMAL STRESS. The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts.
NORMAL STRESS The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts. σ = force/area = P/A where σ = the normal stress P = the centric
More informationModule 7 Design of Springs. Version 2 ME, IIT Kharagpur
Module 7 Design of Springs Lesson 1 Introduction to Design of Helical Springs Instructional Objectives: At the end of this lesson, the students should be able to understand: Uses of springs Nomenclature
More informationHigh Tech High Top Hat Technicians. An Introduction to Solid Mechanics. Is that supposed to bend there?
High Tech High Top Hat Technicians An Introduction to Solid Mechanics Or Is that supposed to bend there? Why don't we fall through the floor? The power of any Spring is in the same proportion with the
More informationMechanics of Materials
Mechanics of Materials 2. Introduction Dr. Rami Zakaria References: 1. Engineering Mechanics: Statics, R.C. Hibbeler, 12 th ed, Pearson 2. Mechanics of Materials: R.C. Hibbeler, 9 th ed, Pearson 3. Mechanics
More informationMATERIALS. Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle?
MATERIALS Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle? What is toughness? strength? brittleness? Elemental material atoms: A. Composition
More informationME Final Exam. PROBLEM NO. 4 Part A (2 points max.) M (x) y. z (neutral axis) beam cross-sec+on. 20 kip ft. 0.2 ft. 10 ft. 0.1 ft.
ME 323 - Final Exam Name December 15, 2015 Instructor (circle) PROEM NO. 4 Part A (2 points max.) Krousgrill 11:30AM-12:20PM Ghosh 2:30-3:20PM Gonzalez 12:30-1:20PM Zhao 4:30-5:20PM M (x) y 20 kip ft 0.2
More informationMechanics of Materials MENG 270 Fall 2003 Exam 3 Time allowed: 90min. Q.1(a) Q.1 (b) Q.2 Q.3 Q.4 Total
Mechanics of Materials MENG 70 Fall 00 Eam Time allowed: 90min Name. Computer No. Q.(a) Q. (b) Q. Q. Q.4 Total Problem No. (a) [5Points] An air vessel is 500 mm average diameter and 0 mm thickness, the
More informationIDE 110 Mechanics of Materials Spring 2006 Final Examination FOR GRADING ONLY
Spring 2006 Final Examination STUDENT S NAME (please print) STUDENT S SIGNATURE STUDENT NUMBER IDE 110 CLASS SECTION INSTRUCTOR S NAME Do not turn this page until instructed to start. Write your name on
More informationPROBLEM #1.1 (4 + 4 points, no partial credit)
PROBLEM #1.1 ( + points, no partial credit A thermal switch consists of a copper bar which under elevation of temperature closes a gap and closes an electrical circuit. The copper bar possesses a length
More informationJohns Hopkins University What is Engineering? M. Karweit MATERIALS
Why do things break? Why are some materials stronger than others? Why is steel tough? Why is glass brittle? What is toughness? strength? brittleness? Elemental material atoms: MATERIALS A. Composition
More informationQUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS
QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State Hooke s law. 3. Define modular ratio,
More informationAdvanced Structural Analysis EGF Section Properties and Bending
Advanced Structural Analysis EGF316 3. Section Properties and Bending 3.1 Loads in beams When we analyse beams, we need to consider various types of loads acting on them, for example, axial forces, shear
More informationSolid Mechanics Homework Answers
Name: Date: Solid Mechanics Homework nswers Please show all of your work, including which equations you are using, and circle your final answer. Be sure to include the units in your answers. 1. The yield
More informationChapter 1 General Introduction Instructor: Dr. Mürüde Çelikağ Office : CE Building Room CE230 and GE241
CIVL222 STRENGTH OF MATERIALS Chapter 1 General Introduction Instructor: Dr. Mürüde Çelikağ Office : CE Building Room CE230 and GE241 E-mail : murude.celikag@emu.edu.tr 1. INTRODUCTION There are three
More information: APPLIED MECHANICS & STRENGTH OF MATERIALS COURSE CODE : 4021 COURSE CATEGORY : A PERIODS/ WEEK : 5 PERIODS/ SEMESTER : 75 CREDIT : 5 TIME SCHEDULE
COURSE TITLE : APPLIED MECHANICS & STRENGTH OF MATERIALS COURSE CODE : 4021 COURSE CATEGORY : A PERIODS/ WEEK : 5 PERIODS/ SEMESTER : 75 CREDIT : 5 TIME SCHEDULE MODULE TOPIC PERIODS 1 Simple stresses
More informationThe science of elasticity
The science of elasticity In 1676 Hooke realized that 1.Every kind of solid changes shape when a mechanical force acts on it. 2.It is this change of shape which enables the solid to supply the reaction
More informationEMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 3 Torsion
EMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 3 Torsion Introduction Stress and strain in components subjected to torque T Circular Cross-section shape Material Shaft design Non-circular
More informationDetermine the resultant internal loadings acting on the cross section at C of the beam shown in Fig. 1 4a.
E X M P L E 1.1 Determine the resultant internal loadings acting on the cross section at of the beam shown in Fig. 1 a. 70 N/m m 6 m Fig. 1 Support Reactions. This problem can be solved in the most direct
More informationMechanics of Solids. Mechanics Of Solids. Suraj kr. Ray Department of Civil Engineering
Mechanics Of Solids Suraj kr. Ray (surajjj2445@gmail.com) Department of Civil Engineering 1 Mechanics of Solids is a branch of applied mechanics that deals with the behaviour of solid bodies subjected
More informationStress Transformation Equations: u = +135 (Fig. a) s x = 80 MPa s y = 0 t xy = 45 MPa. we obtain, cos u + t xy sin 2u. s x = s x + s y.
014 Pearson Education, Inc., Upper Saddle River, NJ. All rights reserved. This material is protected under all copyright laws as they currently 9 7. Determine the normal stress and shear stress acting
More information8 Deflectionmax. = 5WL 3 384EI
8 max. = 5WL 3 384EI 1 salesinfo@mechanicalsupport.co.nz PO Box 204336 Highbrook Auckland www.mechanicalsupport.co.nz 2 Engineering Data - s and Columns Structural Data 1. Properties properties have been
More informationMECHANICS OF MATERIALS. Prepared by Engr. John Paul Timola
MECHANICS OF MATERIALS Prepared by Engr. John Paul Timola Mechanics of materials branch of mechanics that studies the internal effects of stress and strain in a solid body. stress is associated with the
More informationStress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus. Case study
Stress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus Case study 2 In field of Physics, it explains how an object deforms under an applied force Real rigid bodies are elastic we can
More informationAluminum shell. Brass core. 40 in
PROBLEM #1 (22 points) A solid brass core is connected to a hollow rod made of aluminum. Both are attached at each end to a rigid plate as shown in Fig. 1. The moduli of aluminum and brass are EA=11,000
More informationDiscontinuous Distributions in Mechanics of Materials
Discontinuous Distributions in Mechanics of Materials J.E. Akin, Rice University 1. Introduction The study of the mechanics of materials continues to change slowly. The student needs to learn about software
More information13-Nov-2015 PHYS Rotational Inertia
Objective Rotational Inertia To determine the rotational inertia of rigid bodies and to investigate its dependence on the distance to the rotation axis. Introduction Rotational Inertia, also known as Moment
More informationPES Institute of Technology
PES Institute of Technology Bangalore south campus, Bangalore-5460100 Department of Mechanical Engineering Faculty name : Madhu M Date: 29/06/2012 SEM : 3 rd A SEC Subject : MECHANICS OF MATERIALS Subject
More informationSOLUTION 8 7. To hold lever: a+ M O = 0; F B (0.15) - 5 = 0; F B = N. Require = N N B = N 0.3. Lever,
8 3. If the coefficient of static friction at is m s = 0.4 and the collar at is smooth so it only exerts a horizontal force on the pipe, determine the minimum distance x so that the bracket can support
More informationElastic Properties of Solids (One or two weights)
Elastic properties of solids Page 1 of 8 Elastic Properties of Solids (One or two weights) This is a rare experiment where you will get points for breaking a sample! The recommended textbooks and other
More informationENG2000 Chapter 7 Beams. ENG2000: R.I. Hornsey Beam: 1
ENG2000 Chapter 7 Beams ENG2000: R.I. Hornsey Beam: 1 Overview In this chapter, we consider the stresses and moments present in loaded beams shear stress and bending moment diagrams We will also look at
More informationChapter 12. Static Equilibrium and Elasticity
Chapter 12 Static Equilibrium and Elasticity Static Equilibrium Equilibrium implies that the object moves with both constant velocity and constant angular velocity relative to an observer in an inertial
More information4. BEAMS: CURVED, COMPOSITE, UNSYMMETRICAL
4. BEMS: CURVED, COMPOSITE, UNSYMMETRICL Discussions of beams in bending are usually limited to beams with at least one longitudinal plane of symmetry with the load applied in the plane of symmetry or
More informationEDEXCEL NATIONAL CERTIFICATE/DIPLOMA MECHANICAL PRINCIPLES AND APPLICATIONS NQF LEVEL 3 OUTCOME 1 - LOADING SYSTEMS TUTORIAL 3 LOADED COMPONENTS
EDEXCEL NATIONAL CERTIICATE/DIPLOMA MECHANICAL PRINCIPLES AND APPLICATIONS NQ LEVEL 3 OUTCOME 1 - LOADING SYSTEMS TUTORIAL 3 LOADED COMPONENTS 1. Be able to determine the effects of loading in static engineering
More information7.4 The Elementary Beam Theory
7.4 The Elementary Beam Theory In this section, problems involving long and slender beams are addressed. s with pressure vessels, the geometry of the beam, and the specific type of loading which will be
More informationCHAPTER 4: BENDING OF BEAMS
(74) CHAPTER 4: BENDING OF BEAMS This chapter will be devoted to the analysis of prismatic members subjected to equal and opposite couples M and M' acting in the same longitudinal plane. Such members are
More informationMechanics of Materials II. Chapter III. A review of the fundamental formulation of stress, strain, and deflection
Mechanics of Materials II Chapter III A review of the fundamental formulation of stress, strain, and deflection Outline Introduction Assumtions and limitations Axial loading Torsion of circular shafts
More informationstructural analysis Excessive beam deflection can be seen as a mode of failure.
Structure Analysis I Chapter 8 Deflections Introduction Calculation of deflections is an important part of structural analysis Excessive beam deflection can be seen as a mode of failure. Extensive glass
More informationModule 3 : Equilibrium of rods and plates Lecture 15 : Torsion of rods. The Lecture Contains: Torsion of Rods. Torsional Energy
The Lecture Contains: Torsion of Rods Torsional Energy This lecture is adopted from the following book 1. Theory of Elasticity, 3 rd edition by Landau and Lifshitz. Course of Theoretical Physics, vol-7
More informationRussell C. Hibbeler. Chapter 1: Stress
Russell C. Hibbeler Chapter 1: Stress Introduction Mechanics of materials is a study of the relationship between the external loads on a body and the intensity of the internal loads within the body. This
More informationCHAPTER -6- BENDING Part -1-
Ishik University / Sulaimani Civil Engineering Department Mechanics of Materials CE 211 CHAPTER -6- BENDING Part -1-1 CHAPTER -6- Bending Outlines of this chapter: 6.1. Chapter Objectives 6.2. Shear and
More informationPart 1 is to be completed without notes, beam tables or a calculator. DO NOT turn Part 2 over until you have completed and turned in Part 1.
NAME CM 3505 Fall 06 Test 2 Part 1 is to be completed without notes, beam tables or a calculator. Part 2 is to be completed after turning in Part 1. DO NOT turn Part 2 over until you have completed and
More informationD : SOLID MECHANICS. Q. 1 Q. 9 carry one mark each.
GTE 2016 Q. 1 Q. 9 carry one mark each. D : SOLID MECHNICS Q.1 single degree of freedom vibrating system has mass of 5 kg, stiffness of 500 N/m and damping coefficient of 100 N-s/m. To make the system
More informationSRI CHANDRASEKHARENDRA SARASWATHI VISWA MAHAVIDHYALAYA
SRI CHANDRASEKHARENDRA SARASWATHI VISWA MAHAVIDHYALAYA (Declared as Deemed-to-be University under Section 3 of the UGC Act, 1956, Vide notification No.F.9.9/92-U-3 dated 26 th May 1993 of the Govt. of
More informationCHAPTER 6: Shearing Stresses in Beams
(130) CHAPTER 6: Shearing Stresses in Beams When a beam is in pure bending, the only stress resultants are the bending moments and the only stresses are the normal stresses acting on the cross sections.
More informationConsider an elastic spring as shown in the Fig.2.4. When the spring is slowly
.3 Strain Energy Consider an elastic spring as shown in the Fig..4. When the spring is slowly pulled, it deflects by a small amount u 1. When the load is removed from the spring, it goes back to the original
More informationUse Hooke s Law (as it applies in the uniaxial direction),
0.6 STRSS-STRAIN RLATIONSHIP Use the principle of superposition Use Poisson s ratio, v lateral longitudinal Use Hooke s Law (as it applies in the uniaxial direction), x x v y z, y y vx z, z z vx y Copyright
More informationAPI 11E - Specification for Pumping Units
API 11E - Specification for Pumping Units 5 Beam Pump Structure Requirements 5.1 General Requirements for beam pump structures are specified in the following sections. Only loads imposed on the structure
More information