L/O/G/O 單元操作 ( 三 ) Chapter 21 Distillation 化學工程系李玉郎
|
|
- Sherilyn Randall
- 6 years ago
- Views:
Transcription
1 /O/G/O 單元操作 ( 三 ) Chapter 21 istillation 化學工程系李玉郎
2 ifferent methods: Batch: Single stage without reflu -- Simple dist. Multi-stage with reflu Continuous: Single stage without reflu--flash dist. Multi-stage with reflu -- rectification
3 Flash istillation ( 急驟蒸餾或平衡蒸餾 ) Flash istillation ( 急驟蒸餾 or 平衡蒸餾 ) c : pressure-reduced value d : vapor-liquid separator separated streams are in equilibrium For binary mitures: Assume 1 mole feed seperated into: f mole vapor, y (1-f) mole liquid, B Material balance to the more volatile component : F = y f + B (1-f) (21.1) y y y B y f F 1 (21.2) f f To solve B and y, equilibrium data should be provided ( B,y ) : intersection of line (21.2) and equilibrium curve. 3
4 f = f (T,P), depends on the enthalpy balance Eq (21.2) y 1 f f f F (21.2) A straight line, slope : 1 f f etting = F in Eq (21.2) y = F, that is ( F, F ) is a point on line Eq (21.2) The material-balance line crosses the diagonal at = F for all values of f. 4
5 slope : 1 f f
6 Eample 21.1 A miture of 50 mole percent benzene and 50 mole percent toluene is subjected to flash distillation at a separator pressure of 1 atm. The vapor-liquid equilibrium curve and boiling-point diagram are shown in Figs and Plot the following quantities, all as functions of f, the fractional vaporization: the temperature in the separator (T), the composition of the liquid leaving the separator ( B ), and the composition of the vapor leaving the separator (y ).
7 Feed point ( F, F ) = (0.5,0.5), Operation line: f y 1 f A given f value ( F, F ) op line Intersection ( B,y ) with EQ line Slope (1-1/f) Solution f F 0.67 dew point line (y) bubble point line ()
8
9 Continuous istillation with Reflu : Rectification Flash distillation etensively used in petroleum refining, Not effective in separation components of comparable volatility, which requires the use of distillation with reflu. Rectification continuous distillation with reflu
10 liquid and vapor leaving the plate are brought into equilibrium n+1 n n-1 y n+1 y n yn-1
11 A : more volatile component B : less volatile component (in dew point) liquid (heat of vaporization) low boiler, A high boiler, B (heat of condensation) vapor (in bubble point) heat to vaporize A = heat released in condensation B
12 Combination rectification and stripping Reflu provides the downflowing liquid in the rectifying section that is needed to act with the up flowing vapor. Without the reflu, no rectification would occur in the rectifying section Feed pre-heater
13 Overall material balances for two-component systems Feed : F mole/h, F Overhead product: mole/h, Bottom product: B mole/h, B. Two independent overall material balances can be written. Total-material balance F = B + (21.3) Component A balance F F = + B B (21.4) Eliminating B from these equations gives Eliminating gives Material Balances in Plate Columns (21.5) Equations (21.5) and (21.6) are ture for all values of the flows of vapor and liquid within the column F B F F B B F B (21.6) 13
14 Net Flow rates a = a + = a - a a X a X n+1 = n + = n+1 - n > F X F m = m+1 + B B = m m+1 b = b + B B = b - b < B X B
15 Net flow rate A material balance around the condenser and accumulator in Fig gives = a - a 1st plate (21.7) Considering the part of the plant enclosed by control surface I in Fig A total material balance around this control surface gives = n+1 n plate n (21.8) is the net flow rate of material upward in the upper section of the column. Regardless of changes in and, their difference is constant and equal to. Similar material balances for component A give the equations = a y a a a = n+1 y n+1 n n (21.9) Quantity is the net flow rate of component A upward in the upper section of the column. It, too, is constant throughout this part of equipment.
16 For Stripping section: B = b - b = m - m+1 (21.10) B B = b b - b y b = m m - m+1 y m+1 (21.11) The net flow rate of total material is B; of component A is B B.
17 Because there are two sections in the column, there are also two operating lines. For the rectifying section Based on Eq.(20.7) in Chap. 20 the operating line for this section is y n1 n1 ya n1 Substitution for a y a a a from Eq. (21.9) gives y n1 n n n n1 n a n1 The slope of the line defined by Eq. (21.13) is, as usual, the ratio of the flow of the liquid stream to that of the vapor stream. n+1 = n + Operating lines a a (21.12) = a y a a a (21.13) n yn1 n (21.14) n n 17
18 n+1 y n+1 = n n + y n1 n n1 n n1 (21.13) m m = m+1 y m+1 + B B m+1 y m+1 = m m - B B 18
19 For striping section A material balance over control surface 2 in Fig gives m+1 y m+1 = m m -B B (21.15) m BB y m1 m (21.16) m1 m1 Eq(21.16) is the operating line in the stripping section. Net flow rate in striping section: B = b - b = m - m+1 y m m BB 1 m (21.17) B B m m 19
20 Slope of op line : for rectifying section, slope = for stripping section, slope = n n1 n n m m B <1 >1 The slope of the operating line in the rectifying section is always less than 1.0 In the stripping section the slope is always greater than 1.0. When n, m are constant, the op lines are straight, when n. m are not constant, the op lines are curved, and the position of a curved op line should be determined by mass balance and enthalpy balance. 20
21 Number of Ideal plates: McCabe-Thiele Method Require: (1) Equilibrium curve (2) Operation line straight line: constant molar flow curve line: enthalpy balance is required Number of ideal plate: (1) step by step computation (2) McCabe-Thiele construction on -y diagram. Constant molar overflow: straight operating lines results from nearly equal molar heats of vaporization between components A and B Subscripts: n-1, n, n+1; m-1, m, m+1 are dropped, upper column, lower section 21
22 Eq (21.14) (divided by ) Slope =, intercept = R R y n n n n n n n R R R y R R 1 1 R 22 Reflu ratio (21. 18) (Used in this tet book) (21.19): operation line for rectifying section condenser
23 In Eq (21.19), set n = (, ) is a point at the upper end of OP line or OP line intersects the diagonal at point (, ) n R R R y To determine the operation line, one point is required n n R R R y
24 According to the properties of OP line, the upper terminus is ( c, y 1 ) Condenser and top plate (1). Total condenser: condense all the vapor from plate 1 y 1 = = c, so, ( c,y 1 )= (, ) ( C,y 1 ) (, ) abc represents the top plate
25 (2) Partial and final condenser: y =, y in equilibrium with C. Condenser is equivalent to an additional theoretical stage. y 1 c = y' Tc, c T 1 c 1 condenser y 1, 1 Plate 1 a ( c, y 1 ) end point of column a'b c the top plate
26 If condensate is at its bubble point, T c = T bc, = c, = c ( 1 ) If the reflu (condensate) is cooled below the bubble point, T c < T bc, then 1 <, > c Δ = - c C ( T T C pc bc C (21.21) The actual reflu ratio: C ) Tc, c T 1 = c 1 y' 26 condenser y 1, 1 Plate 1 λ C : heat of vaporization of condensate) C C [ 1 CPC ( Tbc TC ) / C ] (21.22) Normally T bc = T 1 (bubble point of condensate) (p676 description)
27 Bottom plate and re-boiler Eq. (21.17) y m1 m B m m BB B m Constant. y m1 B m B B B (21.23) Find a point on the operation line: Set m = B y m+1 = B (conc. of bottom product) Eq. (21.23) OP line for stripping section, crosses the diagonal at ( B, B ) (21.23) OP line constructed using (1) End point ( B, B ), (2) slope B ( ) 27
28 y b =y N y r y r B abc: bottom plate B reboiler: (An ideal plate) Figure Graphical construction for bottom plate and boiler: Triangle cde, reboiler ; triangle cde, bottom plate. C( b,y r ): end point of the bottom plate
29 Molar flow rate:,, above the feed plate below and of the feed plate Feed plate relationship depends on thermal condition of the feed efine: q = moles of liquid to stripping section per mole of feed (a) Cold feed, q>1, F, (b) Saturated liquid, q=1, F, (c) Partially vapor, 0<q<1, F, (d) Saturated vapor, q=0,, F F (e) Superheated vapor, q<0,, F 29
30 (a) Cold feed, q>1 (b) Saturated liquid, q=1 (c) Partially vapor, 0<q<1 F, F, F, (d) Saturated vapor, q=0 (e) Superheated vapor, q<0, F, F 30
31 For cold-liquid feed: For superheated vapor q C C q P ( Tb T ( d TF T ) P F 1 (21.24) ) (21.25) C P, C P = specific heat of liquid and vapor, respectively T F = temp. of feed T b, T d = bubble point and dew point of feed, respectively λ = heat of vaporization 31
32 For 1 mole feed, to liquid: q, to vapor: (1-q) F mole feed, to liquid: Fq, to vapor: F(1-q) qf ( 1 q) F Material-balance for rectifying and stripping sections y n = n-1 + (21.28) or qf (21.26) or Feed line ( 1 q) F (21.27) y m m1 B B (21.29) et y n = y m, n-1 = m-1 Eq. (21.28) Eq (21.29) y( ) ( ) B B (1-q)F -qf F F y 1 q q F 1 q (21.30) (21.31) Feed line depends on F and q slope: -q/(1-q), crosses the diagonal at ( F, F ) The positions where rectifying line and striping line intersect 32
33 Method: (1) locate the feed line: point ( F, F ), slope: (2) locate the rectifying line: point (, ); intercept (3) draw the stripping line Construction of operation lines R 1 ; slope: q 1 q R R 1 point ( B, B ); intersection of feed and rectifying lines Satu. vapor. Satu. iq. Cold feed (, ) a: cold feed: q > 1, slope > 0 b: saturated liq.: q = 1, slope c: partially vapor: 0 < q < 1, slope < 0 d: saturated vapor: q = 0, slope = 0 e: superheated vapor: q < 0, slope >0 ( B, B ) 33
34 Transfer can be occurred between a - b Feed plate location optimum location Optimum feed plate No. of plate: 7+1 reboiler feed on plate 5 If feed on plate 7 (----) composition of liquid on feed plate Fig X F : Feed composition No. of plate: 8 + a reboiler Optimum location the steps transfer from rectifying line to stripping line, so that the plate number is as small as possible
35 Construction can start either at bottom or at top Optimum location the steps transfer from rectifying line to stripping line, so that the plate number is as small as possible Criterion transfer is made immediately after the value is less than the coordinate of the intersection of the two operating lines Feed plate the triangle that has one corner on the rectifying line, and one corner on the stripping line. Feed on the wrong plate may seriously affect the column performance. Feed close to a or b will lower the quality of both the top and bottom product
36 Heat effects of entire unit condenser and reboiler Heat added in the reboiler : q r small) Amount of stream required: λ s : latent heat of steam λ: molar latent heat of miture If q = 1, feed at saturated liquid, heat supplied in reboiler = heat removed in the condenser = ( ) ( ) Amount of cooling water required: m W T 2 -T 1 = temp. rise of cooling water Heating and cooling requirements T 2 T 1 m s s ( ) (21.33) (sensible heat change of liquid is (21.32) F, H F b X b H b 36 q c = λ up q r = λ low B, H B, H
37 , H q c = λ up F, H F b X b H b B, H B qr = λlow 37
38 Base: Benzene X F = 0.4 X = 0.97 X B = 0.02 R = / = 3.5/1 λ B = 7360 cal/gmole λ T = 7960 cal/gmole (a): =?, B=? (b): N =?, feed plate? (c): steam required? (kg/h) (d): cooling water required? (m 3 /h)
39 X F = 0.4 X = 0.97 X B = =85.84 F = + B, F XF = + B B F F B B
40 (b). Calculate number of ideal stage and feed position (i) Feed at T b (95 ) : q=1 (saturated liquid) feed line: ( F, F ) = (0.44,0.44) slope = -q/(1-q) = rectifying line: (, ) = (0.974,0.974) intercept = /(R +1) = 0.974/(3.5+1) = stripping line: ( B, B ) = (0.0235,0.0235) intersection of feed line and rectifying line Number of ideal stages: 11 + one reboiler Feed plate: The 7 th plate
41 b-(ii): feed at liquid of 20 (T b = 95,C P = 0.44 cal/g. ) q C ( Tb T P F (95 20) = 1.37 Slope of feed line: -q/(1-q) = 3.70, ( F = 0.44) ) C P = = cal/g-mol, Number of ideal stages: 10 + one reboiler Feed plate: The 6 th plate 41
42 (b)-(iii): feed is a miture of 2/3 vapor, 1/3 liquid. By definition: q = 1/3 Slope of q line = - q/(1-q) = -0.5, ( F = 0.44) No of ideal plates: 12 + one reboiler Feed plate: the 7th plate
43 (c) Calculate the steam required per hours. m s, calculate first s = +(1-q)F = F(1-q) = + = (/ + 1 ) = (R +1) = 153.4(3.5+1) = 690 (kg-mole/h) = (1-q) Because at the bottom of colum, it is more reasonable to use the λ value of higher boiler compound (toluene) λ = 7960 (cal/gmole) m s s = + Fq - F ms 7960[ (1 q)]
44 (d) Calculate the cooling water required (in: 25, out: 40 ) ρ= kg/m 3 ) m w C PW ( T T1) 2 (7360 is more reasonable) (40 25) olume flow rate = m3 /h Kg/h 44
45 cold q Steam req. No. ideal plate (N) Satu. iq. Cold feed Satu. vapor If the feed is more cold, N decreases, steam required increases. The total energy requirement including (1) reboiler, (2) preheater about the same Reasons for preheating the feed: (1). Keep up = down (2). Use the energy of the hot-liquid stream, such as the bottom product. 45
46 Slope of rectifying line: R /(R +1) = (/) Minimum number of plates (N min ) R increase slope increases N ideal decreases R infinite total reflu, (=), (/ = 1), slope = 1 (R = / = ), OP line = diagonal At total reflu, the number of plates is a minimum, but the rates of feed and of both the overhead and bottom products are zero one limiting case in the operation of fractionating columns. No feed, no discontinuity Between the upper and lower section 46
47 Slope of rectifying line: R /(R +1) = (/) R increase slope increases N ideal decreases 最小理論板數 R ( 全回流 ) 47
48 Simple method for calculating N min --- for ideal miture and constant α AB α AB : relative volatility y / Ae Ae AB (21.34) ybe / Be For 2 component system: y Be = 1 y Ae, Be = 1 Ae Eq (21.34) y e AB e 1 ( 1) AB e (21.35) Raoult s law: P A = P A A, y A = P A /P = P A A /P, P B = P B B, y B = P B /P = P B B /P y A / A = P A /P y B / B = P B /P AB y y A B / / A B P P A B '/ P '/ P P P A B ' ' P A /P B does not change much with temperatures column, so the relative volatility can be taken as constant. 48
49 For a binary system y A /y B and A / B may be replaced by y A /(1-y A ) and A /(1- A ), so Eq. (21.34) can be written for plate n+1 as AB y y Ae Be / / Ae Be y Ae Ae / y / Be Be y n1 n1 AB 1 yn 1 1 n 1 (21.37) ---- EQ line For the total reflu, = 0 and / = 1, slope=1, the operating line is the 45 line. OP line: ( n, y n+1 ), y n+1 = n --- OP line combine EQ and OP lines: n n1 AB 1 n 1 n 1 (21.38) At the top of the column, if a total condenser is used, y 1 =, so Eq.(21.37) becomes for n=0, Eq. (21.37) 1 AB (21.39) 49
50 1 AB 1 1 Writing Eq. (21.38) for a succession of n plates gives 1 2 n=1 AB n 1 n AB 1 1 n 1 If Eq. (21.39) and all the equations in the set of Eqs. (21.40) are multiplied together: ( n (21.39) (21.40) n n AB ) (21.41) n n n1 AB 1 n 1 n 1 For the entile column, n=n min +1 reboiler, n = B, (21.41) gives 1 ( AB ) N min 1 B 1 B 50
51 Solving the equation for N min by logarithms gives 1 ( AB ) N min 1 B 1 B N min ln[ (1 ln B ) / AB B (1 ) 1 (21.42) Equation (21.42) is the Fenske equation, which applied when α AB is constant. If the change in the value of α AB from the bottom of the column to the top is moderate, a geometric mean of the etreme values is recommended α AB. 51
52 Minimum reflu, R m minimum reflu ratio M a a min When R decreases R slope decreases ( line upward) R 1 OP lines moves upwards toward the EQ line, R no. of plates increases. ( N : ) a min --- No of plates is infinity. (, y ) At R m (minimum reflu) OP line, feed line intersect at EQ line (ad, bd, fd) Rm y' slope : Rm 1 ' At R m, the plates required to obtain is. If R < R m, even the N is, the separation y' Rm (21.44) B cannot be approached. y' ' B For EQ curve which is concave downward (Eq 24.11) 52
53 for system with EQ curve of concavity upward --- ethanol / water ine correspondings to the minimum reflu ac small R The OP line that is tangent to the EQ line. higher R feed line R, min 53
54 At minimum reflu ratio, the number of ideal plates is infinite. There are regions where liquid or vapor concentrations do not change from plate to plate ( n = n-1 ; y n+1 = y n ). These regions are called invariant zone, or pinch point ( 挾點 ) The d point in Fig (intersection of q line and EQ line) the concentrations at feed plate the concentrations of invarient zone above feed plate : / below feed plate : / Invarient zone, ( pinch point ) the only difference of the two zones feed plate rectifying section invariant zone stripping section 54
55 Optimum reflu ratio --- consider the total fied charges (1) Fied charges on the heat echange equipment, (the reboiler and condenser) increase steadily with the reflu ratio (2) Fied charges on equipment cost of unit: total plate area (No. of plates cross sectional area) N Area for a given production ( is constant ), when R is increased,, No. of plate decreases (N ),, increase, column diameter increases. (Area ) Total cost: (1) + (2) drop sharply at first with increasing R, then pass through a very shallow minimum optimum reflu ratio R m At optimum reflu ratio: Steam cost 2/3 total cost R (optimum) : not much greater than R m 55
56 Effect of reflu ratio when R,, q c q c = λ up, H, q r N, decreases F, H F Area, increases b X b H b B, H B qr = λlow 56
57 When energy costs are relatively high R (optimum) closer to R m Actually, most plants are operated at reflu ratios somewhat above the optimum, because the total cost is not sensitive to reflu ratio in this range. EXAMPE What are (a) the minimum reflu ratio and (b) the minimum number of plates for cases (b)(i), (b)(ii), and (b)(iii) of Eample 21.2? Solution: in eample = F = 0.44 (a) minimum reflu ratio: intersection of feed line EQ line, (, y ) (, y ) (0.972, 0.972) q = 1 = 1.37 = slope : R R m 1 m y y R m y' y' ' 57
58 (b) minimum number of plates the OP lines coincide with the diagonal, the results have no difference between the three cases. 8 ideal plates + one reboiler Fig eample 21.3 (b) 58
59 Nearly pure products For McCabe - Thiele Method, when either the bottom or overhead product is nearly pure, a single diagram covering the entire range of concentrations is impractical because the steps near = 0 and = 1 become small. This problem can be solved by : (1) Use auiliary diagram of large scale for the ends (2) Computer calculation (3) Eq (20.27) when EQ line and OP line are both straight Raoult s law applies to the major component Henry s law applies to the minor component 59
60 EXAMPE A miture of 2 mol percent ethanol and 98 mol percent water is to be stripped in a plate column to a bottom product containing not more than 0.01 mol percent ethanol. Steam, admitted through an open coil in the liquid on the bottom plate, is to be used as a source of vapor. The feed is at its boiling point. The steam flow is to be 0.2 mol per mole of feed. For dilute ethanol-water solutions, the equilibrium line is straight and is given by y e = 9.0 e. How many ideal plates are needed? Solution: dilute solution, constant, y e = 9.0 e EQ line is straight Eq (20.27) can be used * * ln[( ya ya) /( yb yb)] N * * ln[( yb ya) /( yb ya)] y b = 0 b = calculate y a by material balance steam ( a b ) ( ) ( ya yb) ( a b ) ya yb * y a 9.0 * y b 9.0 a b a = 0.02 n[( ) /( )] N 7.6 ideal plates n [( ) /( )] 60 y a
61 Enthalpy Balances ariations in and ( ideal solution is assumed ) T d enthalpy balances material balances, phase equilibria T b : benzene = 80 o C toluene = o C Reference Temp. = 80 o C (liquid) apor: dew point iquid: bubble point H C T P, T ref at T b H H,ByB H,TyT ( function of T d ) toluene at T b = o C (benzene) benzene 80 o C T d Tref C P, B T d Tref C P, T H, B B, ref, H, T T, ref, 61
62 _
63 The enthalpy balance for the entire system FH FH F F q H BH q (21.45) r H BH B B c ( feed at T b ) q c = λ up, H qr q c ( only one is independent ) F, H F control q r R (Eq 21.45) q c b X b H b B, H B qr = λlow 63
64 Enthalpy balance in rectifying and stripping sections Enthalpy balance within control surface I n H y 1, n1 n H, n H (21.46) Enthalpy balance to condenser q c a H H H a y, a H a H q c qc a H y, a a H H (21.47) (21.47) into (21.46) H H H n 1 y, n1 n, n a y, a a H (21.48) 64
65 (21.47) into (21.46) material balance y known : n, solve : n, n+1, y n+1 n1 n 1 n n n n1 n1 Find n+1 and n at specified n value Known : a H y,a, RH,, f (y n+1 ) f ( n ) a H n 1 y, n1 n, n a y, a RH (21.48) (21.49) (21.50) by trial and error, using (21.48), (21.49), (21.50) T Chosen : n b H,n (From Fig 21.24) (n) (n-1) Trial and error : (1) assume n+1 = a, n = a (constant molar flow rate) (2) calculate y n+1 (Eq 21.49) H y,n+1 (Fig 21.24) ; (3) n = n+1 (Eq 21.50) (4) calculate new n+1 by Eq (21.48), n by (21.50) ; (5) repeat steps (2) (4) 65 until (y n+1 ) (y n+1 ) step m step m+1 H H
66 H,n H y,n+1 T b try n = a Assume n y n+1 new new y n+1 f (y n+1 ) f ( n ) H OP line n+1 = a H H n 1 y, n1 n, n a y, a T d a RH n enthalpy OP net flow rate line n+1 compare or repeat y n1 n n n1 n1 1 a n n H H
67 m H,m + q r = m+1 H y,m+ +BH B enthalpy balance for stripping section ( control surface II ) enthalpy balance : H individual material balance : overall material balance : H m 1 y, m1 m, m m y m1 m1 m B m1 q m r BH B B m1 B (21.51) (21.52) (21.53) 67
68 Find m+1 and m at specified m value trial and error Known : BH B, B, B, q r ( from ) Choose : m H,m T b H,n T b Assume n y n+1 new new y n+1 Trial and error : try n = b H y,n+1 OP line n+1 = b T d (1) assume m+1, m ( first m+1 = b, m = b ) (2) calculate y m+1 ( from Eq ) H y,m+1 (3) calculate new m+1 ( using and ) (4) calculate new m ( Eq ) H m 1 y, m1 m, m y m1 m1 n H enthalpy OP net flow rate line n+1 compare or repeat m m m1 m B B B m1 q r BH B (5) repeat steps (2) (4) 68
69 Solution : Base component : Benzene a F = 0.5, = 0.98, B = 0.02 Assume F = 100 mole F F B B = 50 mole, B = 50 mole 69
70 Calculate R ( = 1.2R m ), q = 1.0 Eq (21.3) R M y y ( based on constant ) = 0.5 = F, y = 0.72 ( EQ curve) y RM 1.18 y a R R 1.2RM 1.42 ( ) a = R = 1.42 = = 71 mole a 1 = R + = = 121 mole 1 = R = 71 mole a 70
71 Enthalpy balance Eq (21.48) n1h y, n1 nh, n a H y, a RH a Reference Temp : 80 o C ( T b of Benzene) H 0 ( nearly pure benzene at T b ) HR H CP, T 80 H,a for benzene vapor at T o C, H y,b = ( T 80) --- (A) enthalpy of vaporization at T o C H Cp ( Tb T) Cpv ( T Tb ) H, b H H, b ( T T)( Cp calculate first for toluene vapor at T o C, H y,t = ( T 80) --- (B) at T = 80 o C ΔH = ( )(40 30) = 8174 (cal / mole) b at 80 o C Cp So, toluene vapor at T o C, H y,t = (T 80 ) v ) a a liq. Toluene T o C T b (110.6) ΔH Cp l Cp v vaporization ΔH b = 7960 vapor of toluene T o C T b (110.6)
72 Evaluate H y,1 ( H y,a ) y B Top plate temp. 80 o C y T H y,1 = 0.98 H y,b H y,t = = 7376 (cal mole) Eq (A) and Eq (B) H y,b = ( T 80) --- (A) H y,t = ( T 80) --- (B) Evaluate intermedia point y n+1, n Pick n = 0.5, T b = 92 o C ( from Fig 21.3 ) H, n C P, (92 80) ( )(92 80) 438 cal mole C P, : mean value 72
73 H,n H y,n+1 T b try n = a Assume n y n+1 new new y n+1 OP line n+1 = a T d n enthalpy OP net flow rate line n+1 compare or repeat
74 To estimate y n+1 : use : n = 1 = 71 mole n+1 = 1 = 121 mole / value to draw the OP ine, and get y n+1, or ( ) n yn 1 n y n n1 Fiqure McCabeThiele diagram for Eample 21.5 benzene-toluene distillation: dashed line y n dew point T d 93 o C ( Fig 21.3 ) Benzene : 0.7, Toluene : 0.3 H y,b = ( T 80) --- (A) H y,t = ( T 80) --- (B)
75 Calculate H y,n+1 ( at 93 o C ) H y,n+1 = 0.7 H yb,n H yt,n+1 = 0.7( ) + 0.3( ) = 7942 Eq (21.48) -- n+1 H y,n+1 = n H,n + 1 H y,1 R H, ( n = n+1 ) n+1 (7942) = ( n+1 50) (7376) H,n H y,b = ( T 80) --- (A) H y,t = ( T 80) --- (B) n+1 = mole, n = 66 mole new n, n+1 ( 1 = 121 ) ( 1 = 71 ) 0 Calculate new y n+1 by Eq ( ) mass balance Eq ( ) y n1 n n1 n n close enough to ( n, y n+1 ) = (0.5, 0.707) 75
76 Similar calculation 1 = 71 1 = 121 pick n = 0.7 y n H y,n+1 y n+1 T b H,n gives : n+1 = 118, n = 68, y n+1 = ( n, y n+1 ) = (0.7, 0.818) T d enthalpy balance n+1 n (0.818) OP line : solid line in Fig Fiqure McCabeThiele diagram for Eample 21.5 benzene-toluene distillation:, based on constant molar overflow;, based on enthalpy balance. 76
77 To estimate the OP line of stripping section, q r should be known first, use of overall enthalpy balance F H F + q r = H + B H B + q c H F : feed at boiling point ( F = 0.5, T F = 92 o C ) H H : = 0 F CP, ( T 80) ( )(92 80) 438 cal H B : T B 111 o C ( close to T b of toluene, o C ), benzene = 0.02,, toluene = (C) mole H B = ( )(111 80) = 1236 cal mole q c : 1 H y,1 = q c + ( a + )H 0 q c = = 892,496 cal From Eq(c) q r = , = 910,496 cal ( 2% error for q r q c ) 77 a H 1 H y,1 q c H
78 Estimate, b, b enthalpy balance around reboiler : q r + b H,b = b H y,b + B H B b + B H y,b : about 5% benzene at 111 o C ( Fig 21.3 ) H y,b = 0.05 H y,b (benzene) H y,b (toluene) = 0.05( ) ( ) = 9141 cal mole?? H,b : about 4% benzene at 110 o C ( Fig 21.3 ) b, H,b = 4% 110 o C H,b = ( )(110 80) = 1192 cal mole () 111 o C, y = 0.05 b, H y,b q r B, H B 111 o C, B =
79 b = b + 50, into Eq () q r + b H,b = b H y,b + B H B ( b + 50) Eq () b q r 50H H y,b,b H BH,b B (1192) 50(1236) b another method to estimate the approimate value b q H r
80 Calculate an intermediate value of m+1 Eq (21.51) m+1 H y,m+1 = m H,m + q r B H B Eq (21.52) y m1 m m1 m B B m1 Eq (21.53) m = m+1 + B pick m = 0.4 ( T b = 95 o C ) (1) first assume m = b = ; m+1 = b = ( constant molar flow ) get y m+1 = 0.55 ( from fig 21.25, dashed line ) ( T m+1 = 97 o C ) (2) calculate H,m ; H y,m+1 H,m = ( )(95 80) = 558 y m+1 = 0.55 T d = 97 o C H y,m = 0.55[ (97 80)] [ (97 80)] = 8194 H y,b H y,t 80
81 Eq (21.51) m+1 H y,m+1 = m H,m + q r B H B 8194 m+1 = ( m ) , m+1 = ; m = = ( b = 114.3) ( b = 164.3) Almost no change in and in the stripping section OP line can be drawn as straight line ( B, B ) = (0.02, 0.02), intersection of upper OP line q line No. of ideal stages : (i) 27 ideal stage, consider the variation of, (solid line in Fig 21.25) (ii) 21 ideal stage ; assume, are constant (dashed line) 81
82 No. of ideal stages : constant, (i) 27 ideal stage, consider the variation of, (solid line in Fig 21.25) (ii) 21 ideal stage ; assume, are constant (dashed line) ( n, y n+1 ) = (0.5, 0.707) ---- variation of, ( n, y n+1 ) = (0.5, 0.7) ---- constant,
83 Rectifying section : decreases 7% (mainly due to higher molar heat of vaporization of toluene) λ T > λ B Sensible heat: high small vapor : C P, liquid : C P, small high >, C P, > C P, effect canceled Stripping section :, almost no change F 50% T 50% B 1 = 71 n n-1 n = 0.5 n = 66 Be. To. 1 = 121 y n y n+1 = n+1 = 116 small small high high C P, C P, C P, < C P, Heat gain by liq. Heat released by vapor part of sensible heat of liquid should be supplied by condensation of vapor b = m = 0.4 m = y m+1 = 0.55 m+1 = b = 114.3
84 The slight upward shift of operation lines may be important when operation close to the R m ( minimum reflu ratio ). When R 2R m,the effects of operatingline curvature would be very small. for straight OP line, slope = for curved OP line, slope local value of n n 1 84
85 Reason : Eq (21.49) n+1 y n+1 = n n + n = n+1 or n+1 = n + Eq (21.49) becomes n+1 y n+1 = ( n+1 ) n + n+1 (y n+1 n ) = ( n ) --- (21.54) Eq(21.55) Eq(21.54) for stripping section n n1 or ( n + )y n+1 = n n + n (y n+1 n ) = ( y n+1 ) --- (21.55) n yn 1 (21.56), slope of line connecting (, ), ( n, y n+1 ) m m1 n 1 y m1 m B B n ( B, B ), ( m, y m+1 ) 85
86 File download (PF files): in FTP of ab. 主機位址 : 使用者名稱 : units 密碼 : units 連接埠 : 650
87 m m H,m m+1 y m+1 H y,m+1 b b B, B, q r H B
Distillation. This is often given as the definition of relative volatility, it can be calculated directly from vapor-liquid equilibrium data.
Distillation Distillation may be defined as the separation of the components of a liquid mixture by a process involving partial vaporization. The vapor evolved is usually recovered by condensation. Volatility
More informationMcCabe Thiele Graphical Equilibrium-Stage
Limiting condition McCabe Thiele Graphical Equilibrium-Stage When analzing or designing a process, it is useful to look at limiting cases to assess the possible values of process parameters. In distillation
More informationMass Transfer Operations I Prof. Bishnupada Mandal Department of Chemical Engineering Indian Institute of Technology, Guwahati
Mass Transfer Operations I Prof. Bishnupada Mandal Department of Chemical Engineering Indian Institute of Technology, Guwahati Module - 5 Distillation Lecture - 5 Fractional Distillation Welcome to the
More informationMass Transfer Operations I Prof. Bishnupada Mandal Department of Chemical Engineering Indian Institute of Technology, Guwahati
Mass Transfer Operations I Prof. Bishnupada Mandal Department of Chemical Engineering Indian Institute of Technology, Guwahati Module - 5 Distillation Lecture - 6 Fractional Distillation: McCabe Thiele
More informationSolid-Liquid Extraction
Chapter (10) Solid-Liquid Extraction (( Leaching )) Leaching: is the separation of a solute from solid mixture by dissolving it in a liquid phase. Leaching occurs in two steps: 1. Contacting solvent and
More informationMODULE 5: DISTILLATION
MODULE 5: DISTILLATION LECTURE NO. 5 Determination of the stripping section operating line (SOL): The stripping section operating line (SOL) can be obtained from the ROL and q- line without doing any material
More informationVapor-liquid Separation Process MULTICOMPONENT DISTILLATION
Vapor-liquid Separation Process MULTICOMPONENT DISTILLATION Outline: Introduction to multicomponent distillation Phase Equilibria in Multicomponent Distillation (Pg. 737) Bubble-point and dew-point calculation
More informationMass Transfer Operations I Prof. BishnupadaMandal Department of Chemical Engineering Indian Institute of Technology, Guwahati
Mass Transfer Operations I Prof. BishnupadaMandal Department of Chemical Engineering Indian Institute of Technology, Guwahati Module -5 Distillation Lecture - 8 Fractional Distillation: Subcooled Reflux,
More informationChapter 4: Column Distillation: Internal Stage-by-Stage Balances
Chapter 4: Column Distillation: Internal Stage-by-Stage Balances In Chapter 3 (Introduction to Column Distillation), we performed the external balances or the balances around the distillation column To
More informationComputer Aided Design Module for a Binary Distillation Column
Computer Aided Design Module for a Binary Distillation Column K. R. Onifade Department of Chemical Engineering, Federal University of Technology Minna, Nigeria Abstract A Computer Aided Design (CAD) module
More informationMODULE 5: DISTILLATION
MOULE 5: ISTILLATION LECTURE NO. 3 5.2.2. Continuous distillation columns In contrast, continuous columns process a continuous feed stream. No interruptions occur unless there is a problem with the column
More informationCryogenic Engineering Prof. M. D. Atrey Department of Mechanical Engineering Indian Institute of Technology, Bombay. Lecture No. #23 Gas Separation
Cryogenic Engineering Prof. M. D. Atrey Department of Mechanical Engineering Indian Institute of Technology, Bombay Lecture No. #23 Gas Separation So, welcome to the 23rd lecture, on Cryogenic Engineering,
More informationProblem Appendix Antoine constants Important properties of unordered packings... 22
Contents Sample problems and eercises Distillation... 3 Sample problems... 3 Sample : Calculating vapor phase composition for immiscible liquids... 3 Sample 2: Calculating boiling point and vapor phase
More informationEXTENDED SMOKER S EQUATION FOR CALCULATING NUMBER OF STAGES IN DISTILLATION
EXTENDED SMOKER S EQUATION FOR CALCULATING NUMBER OF STAGES IN DISTILLATION Santanu Bandyopadhyay Energy Systems Engineering and Department of Mechanical Engineering, Indian Institute of Technology, Bombay,
More informationContinuous Distillation 1: McCabe-Thiele Method
Guidelines for the Number of Distillation Separation Stages Februar, 9 refeed Corporation Dr. Yoshio Kumagae Continuous Distillation : McCabe-Thiele Method Continuous Distillation : McCabe-Thiele Method.
More informationAll Rights Reserved. Armando B. Corripio, PhD, P.E., Multicomponent Distillation Column Specifications... 2
Multicomponent Distillation All Rights Reserved. Armando B. Corripio, PhD, P.E., 2013 Contents Multicomponent Distillation... 1 1 Column Specifications... 2 1.1 Key Components and Sequencing Columns...
More informationAll rights reserved. Armando B. Corripio, PhD, PE Flash Distillation Flash Drum Variables and Specifications... 2
Flash Distillation All rights reserved. Armando B. Corripio, PhD, PE. 2013 Contents Flash Distillation... 1 1 Flash Drum Variables and Specifications... 2 2 Flash Drum Balances and Equations... 4 2.1 Equilibrium
More informationReview of Mathematics
Review for Exam #1 Review of Mathematics 2 Weighted Mean A certain property of material 1 is P 1 and that of material 2 is P 2 If x 1 amount (weight or volume) of material 1 is mixed with x 2 amount of
More informationChemical unit operations 2. lectures 2 hours/week calculation seminars weekly 1 hours laboratory weekly 3 hours
Chemical unit operations 2. lectures 2 hours/week calculation seminars weekl 1 hours laborator weekl 3 hours Requirements Attendance will be checked. Requirements for the signature: Attending on minimum
More informationVapor-liquid equilibrium
Vapor-liquid equilibrium From Wikipedia, the free encyclopedia Vapor-liquid equilibrium, abbreviated as VLE by some, is a condition where a liquid and its vapor (gas phase) are in equilibrium with each
More informationDistillation. The Continuous Column. Learning Outcomes. Recap - VLE for Meth H 2 O. Gavin Duffy School of Electrical Engineering DIT Kevin Street
Distillation The Continuous Colun Gavin Duffy School of Electrical Engineering DIT Kevin Street Learning Outcoes After this lecture you should be able to.. Describe how continuous distillation works List
More informationIntroduction: Introduction. material is transferred from one phase (gas, liquid, or solid) into another.
Introduction: Virtually all commercial chemical processes involve operations in which material is transferred from one phase (gas, liquid, or solid) into another. rewing a cup of Coffee (Leaching) Removal
More informationDistillation. Senior Design CHE 396 Andreas Linninger. Innovative Solutions. Michael Redel Alycia Novoa Tanya Goldina Michelle Englert
Distillation Senior Design CHE 396 Andreas Linninger Innovative Solutions Michael Redel Alycia Novoa Tanya Goldina Michelle Englert Table of Contents Introduction 3 Flowsheet 4 Limitations 5 Applicability
More informationDISTILLATION. Keywords: Phase Equilibrium, Isothermal Flash, Adiabatic Flash, Batch Distillation
25 DISTILLATION Keywords: Phase Equilibrium, Isothermal Flash, Adiabatic Flash, Batch Distillation Distillation refers to the physical separation of a mixture into two or more fractions that have different
More informationSee section and the dew and bubble point calculations in example 11.9.
Solution 1.1 See section 11.3.2 and the dew and bubble point calculations in example 11.9. This type of problem is best solved using a spread-sheet, see the solution to problem 11.2. Solution 11.2 This
More informationPhase Separation Degree of Freedom Analysis. Binary Vapor-Liquid Systems. Azeotropic Systems. - Gibbs phase rule F C P 2 -General analysis
Lecture 5. Single Equilibrium Stages (1) Phase Separation [Ch. 4] Degree of Freedom Analysis - Gibbs phase rule F CP2 -General analysis Binary Vapor-Liquid Systems - Examples of binary system - Phase equilibrium
More informationAn Efficient Design of Multi Component Distillation Column by Approximate & Rigorous Method
An Efficient Design of Multi Component Distillation Column by Approximate & Rigorous Method Syed Mujahed Ali Rizwan Senior Lecturer in Chemistry Challenger College, Moinabad, Hyderabad. Abstract: In this
More informationDistillation. JAMES R. FAIR Department of Chemical Engineering The University of Texas Austin, Texas. 5.1 INTRODUCTION 5.
PART Il I N D I V I D U A L S E P A R A T I O N P R O C E S S E S C H A P T E R 5 Distillation JAMES R. FAIR Department of Chemical Engineering The University of Texas Austin, Texas 5.1 INTRODUCTION 5.M
More informationDistillation. Sep-tek. Ch.11 (continued) Distillation (Multistage with reflux) Sigurd Skogestad. Separation of liquid mixtures by repeated evaporation
Sep-tek. Ch.11 (continued) Distillation (Multistage with reflux) Sigurd Skogestad Distillation Separation of liquid mixtures by repeated evaporation multi-stage with reflux Old name: Rectification Basis:
More information0 o C. H vap. H evap
Solution. Energy P (00 ) Pν x 0 5 ρ 850,4 J kg - J kg Power kg s 000,4 600 70 W Solution. 00 o C H evap H vap 0 o C H liq 00 t H liq (4. x0 t ) dt 4.t x0 0 40 0 40 kj kg - H evap 40,68 J mol - (From Appendix
More informationReflections on the use of the McCabe and Thiele method
From the Selectedorks of João F Gomes January 2007 Reflections on the use of the McCabe and Thiele method Contact Author Start Your Own Selectedorks Notify Me of New ork Available at: http://works.bepress.com/joao_gomes/42
More informationCL-333 Manual. MT 303: Batch Distillation
CL-333 Manual MT 303: Batch Distillation Batch Distillation Equipment Operating Panel Refrectometer 1 CL-333 Manual MT 303: Batch Distillation Objectives: To determine the height equivalent to number of
More informationBOUNDARY VALUE DESIGN METHOD FOR COMPLEX DEMETHANIZER COLUMNS
Distillation Absorption 2010 A.B. de Haan, H. Kooijman and A. Górak (Editors) All rights reserved by authors as per DA2010 copyright notice BOUNDARY AUE DESIGN METHOD FOR COMPEX DEMETHANIZER COUMNS Muneeb
More informationShortcut Distillation. Agung Ari Wibowo, S.T., M.Sc Politeknik Negeri Malang Malang - Indonesia
Shortcut Distillation Agung Ari Wibowo, S.T., M.Sc Politeknik Negeri Malang Malang - Indonesia The use of separation column in HYSYS The column utilities in HYSYS can be used to model a wide variety of
More informationL/O/G/O 單元操作 ( 三 ) Chapter 23 Leaching and Extraction 化學工程學系李玉郎
L/O/G/O 單元操作 ( 三 ) Chapter 23 Leaching and Extraction 化學工程學系李玉郎 Leaching Solid extraction, dissolve soluble matter from its mixture with an insoluble solid solid (solute A+ inert B) solvent (C) concentrated
More informationDistillation is a method of separating mixtures based
Distillation Distillation is a method of separating mixtures based on differences in their volatilities in a boiling liquid mixture. Distillation is a unit operation, or a physical separation process,
More information01/12/2009. F. Grisafi
Multicomponent distillation F. Grisafi 1 Introduction The problem of determining the stage and reflux requirements for multicomponent t distillations is much more complex than for binary mixtures. With
More informationChapter 2 Equilibria, Bubble Points, Dewpoints, Flash Calculations, and Activity Coefficients
Chapter 2 Equilibria, Bubble Points, Dewpoints, Flash Calculations, and Activity Coefficients 2.1 Vapour Pressure Calculations The basis for all phase equilibrium calculations are the vapour pressures
More informationEXAMPLE 2: Visualization and Animation of Enthalpy Method in Binary Distillation
EXAMPLE 2: Visualization and Animation of Enthalp Method in Binar Distillation A graphical method that includes energ balances as well as material balances and phase equilibrium relations is the Ponchon-Savarit
More informationJ. Reyes, A. Gómez & A. Marcilla Dpto. Ingeniería Química, Universidad de Alicante, Apdo. de Correos nº 99, Alicante 03080, España.
MULTICOMPONENT RECTIFICATION: A NEW METHOD OF CALCULATION J. Reyes, A. Gómez & A. Marcilla Dpto. Ingeniería Química, Universidad de Alicante, Apdo. de Correos nº 99, Alicante 03080, España. This poster
More informationERT 318 UNIT OPERATIONS
ERT 318 UNIT OPERATIONS DISTILLATION W. L. McCabe, J. C. Smith, P. Harriot, Uit Operatios of Chemical Egieerig, 7 th editio, 2005. 1 Outlie: Batch distillatio (pg. 724) Cotiuous distillatio with reflux
More informationShortcut Design Method for Columns Separating Azeotropic Mixtures
3908 Ind. Eng. Chem. Res. 2004, 43, 3908-3923 Shortcut Design Method for Columns Separating Azeotropic Mixtures Guilian Liu, Megan Jobson,*, Robin Smith, and Oliver M. Wahnschafft Department of Process
More informationComparison of distillation arrangement for the recovery process of dimethyl sulfoxide
Korean J. Chem. Eng., 24(3), 438-444 (2007) SHORT COMMUNICATION Comparison of distillation arrangement for the recovery process of dimethyl sulfoxide Jungho Cho and Dong Min Kim* Department of Chemical
More informationECH 4224L Unit Operations Lab I Thin Film Evaporator. Introduction. Objective
Introduction In this experiment, you will use thin-film evaporator (TFE) to separate a mixture of water and ethylene glycol (EG). In a TFE a mixture of two fluids runs down a heated inner wall of a cylindrical
More informationReview for Exam #1. Review of Mathematics. Weighted Mean
Review for Exam #1 Review of Mathematics Weighted Mean A certain property of material 1 is P 1 and that of material is P If x 1 amount (weight or volume) of material 1 is mixed with x amount of material,
More informationEnergy and Energy Balances
Energy and Energy Balances help us account for the total energy required for a process to run Minimizing wasted energy is crucial in Energy, like mass, is. This is the Components of Total Energy energy
More informationReview of Mathematics
Review for Exam #1 Review of Mathematics 2 Weighted Mean A certain property of material 1 is P 1 and that of material 2 is P 2 If x 1 amount (weight or volume) of material 1 is mixed with x 2 amount of
More informationPRINCIPLES AND MODERN APPLICATIONS OF MASS TRANSFER OPERATIONS
PRINCIPLES AND MODERN APPLICATIONS OF MASS TRANSFER OPERATIONS Jaime Benitez iwiley- INTERSCIENCE A JOHN WILEY & SONS, INC., PUBLICATION Preface Nomenclature xiii xv 1. FUNDAMENTALS OF MASS TRANSFER 1
More information[Thirumalesh*, 4.(8): August, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY CASE STUDY ON MULTICOMPONENT DISTILLATION AND DISTILLATION COLUMN SEQUENCING Thirumalesh. B.S*, Ramesh.V * Assistant Professor
More informationCH2351 Chemical Engineering Thermodynamics II Unit I, II Phase Equilibria. Dr. M. Subramanian
CH2351 Chemical Engineering Thermodynamics II Unit I, II Phase Equilibria Dr. M. Subramanian Associate Professor Department of Chemical Engineering Sri Sivasubramaniya Nadar College of Engineering Kalavakkam
More informationERT 313 BIOSEPARATION ENGINEERING EXTRACTION. Prepared by: Miss Hairul Nazirah Abdul Halim
ERT 313 BIOSEPARATION ENGINEERING EXTRACTION Prepared by: Miss Hairul Nazirah Abdul Halim Definition of Extraction Liquid-Liquid extraction is a mass transfer operation in which a liquid solution (the
More informationChapter 4. Problem SM.7 Ethylbenzene/Styrene Column
Background Chapter 4. Problem SM.7 Ethylbenzene/Styrene Column In Problem SM.6 of the HYSYS manual, a modified form of successive substitution, called the Wegstein method, was used to close the material
More informationAbsorption/Stripping
Absorption/Stripping Gas-liquid separation processes (Ch. 10) Cooling (condenser) Feed A+B Distillation(Ch.11) Absorption (Ch.10) Stripping (Ch.10) B COUNTER-CURRENT MULTISTAGE CONTACT OF GAS AND LIQUID
More informationExam 3 Solutions. ClO g. At 200 K and a total pressure of 1.0 bar, the partial pressure ratio for the chlorine-containing compounds is p ClO2
Chemistry 360 Dr. Jean M. Standard Fall 2016 Name KEY Exam 3 Solutions 1.) (14 points) Consider the gas phase decomposition of chlorine dioxide, ClO 2, ClO 2 ( g) ClO ( g) + O ( g). At 200 K and a total
More informationOutline of the Course
Outline of the Course 1) Review and Definitions 2) Molecules and their Energies 3) 1 st Law of Thermodynamics Conservation of Energy. 4) 2 nd Law of Thermodynamics Ever-Increasing Entropy. 5) Gibbs Free
More informationThe most important nomenclature used in this report can be summarized in:
Notation The most important nomenclature used in this report can be summarized in: V Vapor flow rate V T Vapor flow rate in the top L Liquid flow rate D Distillation product B Bottom product q Liquid fraction
More informationVapour Absorption Refrigeration Systems Based On Ammonia- Water Pair Nagendra M CBM Engineer, Hindusthan Zink.Ltd The specific objectives of this lesson are to: 1. Introduce ammonia-water based vapour
More informationChapter 11 Solution Thermodynamics: Theory
Chapter 11 Solution Thermodynamics: Theory Chapter 6: constant composition fluids. Most commonly in chemical engineering application multi component mixtures of gases or liquids undergo (composition change).
More informationLatin American Applied Research an International Journal of Chemical Engineering. 1997, vol. 27, 1-2, (Accepted: March 20, 1996).
Latin American Applied Research an International Journal of Chemical Engineering. 1997, vol. 27, 1-2, 51-60 (Accepted: March 20, 1996). NEW METHOD FOR DESIGNING DISTILLATION COLUMNS OF MULTICOMPONENT MIXTURES
More informationTHERMAL INTEGRATION OF A DISTILLATION COLUMN THROUGH SIDE-EXCHANGERS
THERMAL INTEGRATION OF A DISTILLATION COLUMN THROUGH SIDE-EXCHANGERS Santanu Bandyopadhyay Energy Systems Engineering and Department of Mechanical Engineering, Indian Institute of Technology, Bombay, Powai,
More informationEfficient Feed Preheat Targeting for Distillation by Feed Splitting
European Symposium on Computer Arded Aided Process Engineering 15 L. Puigjaner and A. Espuña (Editors) 2005 Elsevier Science B.V. All rights reserved. Efficient Feed Preheat Targeting for Distillation
More informationChapter 7 PHASE EQUILIBRIUM IN A ONE-COMPONENT SYSTEM
Chapter 7 PHASE EQUILIBRIUM IN A ONE-COMPONENT SYSTEM 7.1 INTRODUCTION The intensive thermodynamic properties of a system are temperature, pressure, and the chemical potentials of the various species occurring
More informationMass transfer and separation technology Massöverföring och separationsteknik ( MÖF-ST ) , 7 sp
42432 Mass transfer and separation technology Massöverföring och separationsteknik ( MÖF-ST ) 4432, 7 sp. Batch distillation Ron Zevenhoven Åbo Akademi University Thermal and Flow Engineering Laboratory
More informationProcess Classification
Process Classification Before writing a material balance (MB) you must first identify the type of process in question. Batch no material (mass) is transferred into or out of the system over the time period
More informationPhase Diagrams: Conditions for Equilibrium (CfE)
Phase Equilibrium: Conditions for Equilibrium (CfE) Phase Diagrams: Conditions for Equilibrium (CfE) Write down the conditions for equilibrium for: a pure single phase system, a pure multi-phase system,
More informationPlacement and Integration of Distillation column Module 06 Lecture 39
Module 06: Integration and placement of equipment Lecture 39: Placement and Integration of Distillation Column Key word: Pinch Technology, Pinch technology has established that good process integration
More information- L. _/cit ...B N - Q. - PAD"t..t... QatJ11.81L. ><"'g. Below is a blank flow diagram of a generalized distillation column: (10 Points)
Name: February 24, 2015 EXAM 1 P a g e I 1 / e Below is a blank flow diagram of a generalized distillation column: (10 Points) f -- ' Q. - -- N - - L. PAD"t..t... QatJ11.81L _/cit...b >
More informationAvailable online Journal of Scientific and Engineering Research, 2018, 5(2): Research Article
Available online www.jsaer.com, 2018, 5(2):32-39 Research Article ISSN: 2394-2630 CODEN(USA): JSERBR A Shortcut Method for Modeling Multi-Component Distillation in an Existing Column Philomena K. Igbokwe
More informationChE 201 August 26, ChE 201. Chapter 8 Balances on Nonreactive Processes Heat of solution and mixing
ChE 201 Chapter 8 Balances on Nonreactive Processes Heat of solution and mixing Definitions A solution is a homogeneous mixture A solute is dissolved in a solvent. solute is the substance being dissolved
More informationGRAPHICAL REPRESENTATION OF THE CHANGES OF SECTOR FOR PARTICULAR CASES IN THE PONCHON SAVARIT METHOD
GRAPICAL REPRESENTATION OF TE CANGES OF SECTOR FOR PARTICULAR CASES IN TE PONCON SAVARIT METOD J.A. REYES-LABARTA *, M.D. SERRANO and A. MARCILLA *Chemical Engng Department, University of Alicante, Apdo.
More informationEffect of feed on optimal thermodynamic performance of a distillation column
Effect of feed on optimal thermodynamic performance of a distillation column Santanu Bandyopadhyay Energy Systems Engineering, Department of Mechanical Engineering, Indian Institute of Technology, Powai,
More information,, Seong-Bo Kim,Hai-SongBae, and Jeong-Sik Han
Jungho Cho, So-Jin Park,, Myung-Jae Choi,, Seong-Bo Kim,Hai-SongBae, and Jeong-Sik Han Department of Chemical Engineering, Dong-Yang University, Kyoungbuk, 750-711, Korea *Department of Chemical Engineering,
More informationBatchExtractiveDistillationwithLightEntrainer
V. VARGA et al., Batch Extractive Distillation with Light Entrainer, Chem. Biochem. Eng. Q. 20 (1) XXX XXX (2006) 1 BatchExtractiveDistillationwithLightEntrainer V. Varga,*, ** E. Rev,*,+ V. Gerbaud,**
More informationMODELLING OF CRUDE OIL DISTILLATION UNITS FOR RETROFITTING PURPOSES
JICEC05 Jordan International Chemical Engineering Conference V -4 September 005, Amman, Jordan MODELLIG OF CUDE OIL DISTILLATIO UITS FO ETOFITTIG PUPOSES M. Gadalla, *, Z. Olujic, M. Jobson, +,. Smith
More informationTemperature C. Heat Added (Joules)
Now let s apply the heat stuff to real-world stuff like phase changes and the energy or cost it takes to carry it out. A heating curve...a plot of temperature of a substance vs heat added to a substance.
More informationComprehend and execute the 10 elements of effective problem
Lecture 8, 3/9/2012 Chapter 7: A GENERAL Strategy for Solving Material Balance Problems Objectives: Comprehend and execute the 10 elements of effective problem Drive a flow chart and Place labels on the
More informationDistillation. Presented by : Nabanita Deka
Distillation OPTIMIZATION FOR MAXIMISATION Presented by : Nabanita Deka LPG department OIL INDIA LIMITED DATED-04.03.2011 Basics of mass transfer Mass transfer : Transfer of material from one homogeneous
More informationPressure Swing Distillation with Aspen Plus V8.0
Pressure Swing Distillation with Aspen Plus V8.0 1. Lesson Objectives Aspen Plus property analysis RadFrac distillation modeling Design Specs NQ Curves Tear streams Understand and overcome azeotrope Select
More information1. (25 points) C 6 H O 2 6CO 2 + 7H 2 O C 6 H O 2 6CO + 7H 2 O
MEEBAL Exam 2 November 2013 Show all work in your blue book. Points will be deducted if steps leading to answers are not shown. No work outside blue books (such as writing on the flow sheets) will be considered.
More informationName: Discussion Section:
CBE 141: Chemical Engineering Thermodynamics, Spring 2018, UC Berkeley Midterm 2 March 22, 2018 Time: 80 minutes, closed-book and closed-notes, one-sided 8 ½ x 11 equation sheet allowed Please show all
More informationChapter 11 section 6 and Chapter 8 Sections 1-4 from Atkins
Lecture Announce: Chapter 11 section 6 and Chapter 8 Sections 1-4 from Atkins Outline: osmotic pressure electrolyte solutions phase diagrams of mixtures Gibbs phase rule liquid-vapor distillation azeotropes
More informationSensible Heat and Enthalpy Calculations
* Sensible Heat and Enthalpy Calculations Sensible Heat - The amount of heat that must be added when a substance undergoes a change in temperature from 298 K to an elevated temperature without a change
More informationA comparative study on the recovery of 1,2-dichloroethane and the removal of benzene contained in the byproducts of VCM process
Korean J. Chem. Eng., 27(3), 970-976 (2010) DOI: 10.1007/s11814-010-0206-7 RAPID COMMUNICATION A comparative study on the recovery of 1,2-dichloroethane and the removal of benzene contained in the byproducts
More informationSensible Heat and Enthalpy Calculations
Sensible Heat and Enthalpy Calculations Sensible Heat - The amount of heat that must be added when a substance undergoes a change in temperature from 298 K to an elevated temperature without a change in
More informationDATA THAT YOU MAY USE UNITS Conventional Volume ml or cm 3 = cm 3 or 10-3 dm 3 Liter (L) = dm 3 Pressure atm = 760 torr = Pa CONSTANTS
DATA THAT YOU MAY USE UNITS Conventional S.I. Volume ml or cm 3 = cm 3 or 0-3 dm 3 Liter (L) = dm 3 Pressure atm = 760 torr =.03 0 5 Pa torr = 33.3 Pa Temperature C 0 C = 73.5 K PV L-atm =.03 0 5 dm 3
More informationUnit operations are ubiquitous in any chemical process. Equilibrium-Staged Separations using Matlab and Mathematica. ChE class and home problems
ChE class and home problems The object of this column is to enhance our readers collections of interesting and novel problems in chemical engineering. Problems of the type that can be used to motivate
More informationChem/Biochem 471 Exam 2 11/14/07 Page 1 of 7 Name:
Page 1 of 7 Please leave the exam pages stapled together. The formulas are on a separate sheet. This exam has 5 questions. You must answer at least 4 of the questions. You may answer all 5 questions if
More informationProblem 2 Distillation of air (20%) Solution
Problem 2 Distillation of air (20%) A feed with two components (79 mole% N 2 and 21% O 2 ) is to be separated by continuous distillation. (a) Compute equilibrium data (y,x) at 1 atm for N 2 -O 2 at x=0,
More informationCE427 Fall Semester, 2000 Unit Operations Lab 3 September 24, 2000 COOLING TOWER THEORY
CE427 Fall Semester, 2000 Unit Operations Lab 3 September 24, 2000 Introduction COOLING TOWER THEORY Cooling towers are used etensivel in the chemical and petroleum industries. We also know from the thermodnamics
More informationINTRODUCTION: Shell and tube heat exchangers are one of the most common equipment found in all plants. How it works?
HEAT EXCHANGERS 1 INTRODUCTION: Shell and tube heat exchangers are one of the most common equipment found in all plants How it works? 2 WHAT ARE THEY USED FOR? Classification according to service. Heat
More informationBasic Thermodynamics Prof. S. K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur. Lecture No 16
Basic Thermodynamics Prof. S. K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture No 16 Properties of Pure Substances-I Good afternoon. In the last class, we were
More informationThe Chemical Potential of Components of Solutions
CHEM 331 Physical Chemistry Fall 2017 The Chemical Potential of Components of Solutions We have shown that the Gibbs Free Energy for a solution at constant T and P can be determined from the chemical potential
More informationDistilla l tion n C olum u n
Distillation Column Distillation: Process in which a liquid or vapour mixture of two or more substances is separated into its component fractions of desired purity, by the application and removal of heat
More informationCHEMISTRY Topic #2: Thermochemistry and Electrochemistry What Makes Reactions Go? Fall 2018 Dr. Susan Findlay See Exercises in Topic 8
CHEMISTRY 2000 Topic #2: Thermochemistry and Electrochemistry What Makes Reactions Go? Fall 208 Dr. Susan Findlay See Exercises in Topic 8 Vapour Pressure of Pure Substances When you leave wet dishes on
More informationPhase Transformations
Phase Transformations Chapter 8 of Atkins: Sections 8.1-8.3 Phases, Components and Degrees of Freedom Definitions The Phase Rule Two- Component Systems Vapor Pressure Diagrams Composition of the Vapor
More informationLecture 4-6 Equilibrium
Lecture 4-6 Equilibrium Discontinuity in the free energy, G verses T graph is an indication of phase transition. For one-component system, existing in two phases, the chemical potentials of each of these
More informationMake distillation boundaries work for you!
Make distillation boundaries work for you! Michaela Tapp*, Simon T. Holland, Diane Hildebrandt and David Glasser Centre for Optimization, Modeling and Process Synthesis School of Process and Materials
More informationMATSCI 204 Thermodynamics and Phase Equilibria Winter Chapter #4 Practice problems
MATSCI 204 Thermodynamics and Phase Equilibria Winter 2013 Chapter #4 Practice problems Problem: 1-Show that for any extensive property Ω of a binary system A-B: d ( "# ) "# B, = "# + 1$ x B 2- If "# has
More informationDistillation Course MSO2015
Distillation Course MSO2015 Distillation Distillation is a process in which a liquid or vapour mixture of two or more substances is separated into its component fractions of desired purity, by the application
More informationME6301- ENGINEERING THERMODYNAMICS UNIT I BASIC CONCEPT AND FIRST LAW PART-A
ME6301- ENGINEERING THERMODYNAMICS UNIT I BASIC CONCEPT AND FIRST LAW PART-A 1. What is meant by thermodynamics system? (A/M 2006) Thermodynamics system is defined as any space or matter or group of matter
More information