E11 Lecture 8: Fuel Cell Power and Energy Conservation. Professor Lape Fall 2010
|
|
|
- Dustin Osborne
- 5 years ago
- Views:
Transcription
1 E11 Lecture 8: Fuel Cell Power and Energy Conservation Professor Lape Fall 2010
2 Overview How much power can your FC produce? Maximum power Polarization curve How can we convert this power to other forms of useful energy? 1 st law of thermodynamics
3 Hydrogen Fuel Cell Overall Reaction: H 2 + ½ O 2 H 2 O Figure from Fuel Cell Efficiency, a CACHE Module on Energy in the Curriculum. Chemical Energy Electricity
4 Electric Power Voltage, V: Energy required to move a coulomb of electrical charge. Units = Joules/Coulomb (J/C) Current, I: Rate of electrical charges flowing, dq/ dt. Units = Amperes (A), = Coulombs/sec Electric Power, P e or output. Units = Watts (W) = J/s W e P e or W e = VI = Rate of electric work
5 Maximum Theoretical Voltage The maximum theoretical voltage that can be obtained from a fuel cell by converting all chemical energy into electricity at standard pressure is V 0 = ΔG nf where: ΔG is the Gibbs free energy of the overall FC reaction n is the number of moles of electrons per mole of fuel F is Faraday s constant, 96,485 C/mol e -
6 PEMFC Problem #1 What is the maximum theoretical voltage for a hydrogen PEMFC operating at standard pressure and temperature? The standard Gibbs free energy for the reaction of hydrogen and oxygen to produce liquid water ΔG r kj/mol.
7 PEMFC Problem #2 If a PEMFC were to consume all of the hydrogen fed at 5 µg/s, what current would it produce?
8 FC Polarization Curve Losses from fuel and e - crossover through electrolyte Figure from
9 PEMFC Problem #4 A PEMFC with a hydrogen utilization of 75% is fed 5 µg/ s of hydrogen. What is the current produced by the fuel cell?
10 PEMFC Problem #5 A PEMFC with a hydrogen utilization of 75% is fed 5 µg/ s of hydrogen. What is the maximum power the fuel cell can produce?
11 PEMFC Problem #6 A PEMFC with a hydrogen utilization of 75% is fed 5 µg/ s of hydrogen. If it produces 60% of the maximum power, what is the rate of heat production by the fuel cell?
12 PEMFC Problem #7 A PEMFC with a hydrogen utilization of 75% is fed 5 µg/s of hydrogen. If it produces 60% of the maximum power, how many identical PEMFCs would be necessary to provide sufficient power for a Mudduino operating at 5 V with a maximum current of 500 ma?
13 How is energy stored in a system?
14 How is energy transferred to and from a system?
15 Law of Conservation of Energy: The 1 st Law of Thermodynamics Change in amount of energy contained within the system during some time interval = Net amount of energy transferred in across the system boundary by heat transfer during the time interval + Net amount of energy transferred in across the system boundary by work during the time interval = +
16 i-clicker #1 Hot potato! You packed your hot potato in a wellinsulated lunch bag with a cold soda and let it sit for 15 minutes. If you define the entire lunch bag as the system, what is the sign of the heat transfer with the environment? A. Q < 0 (heat transfer out of the lunch bag) B. Q 0 (approx. no heat transfer w/ surroundings) C. Q > 0 (heat transfer into the lunch bag) D. I heart Mr. Potato Head
17 i-clicker #2 You packed your hot potato in a well-insulated lunch bag with a cold soda and let it sit for 15 minutes. If you define the potato as the system, what is the sign of the heat transfer with the environment? A. Q < 0 (heat transfer out of the potato) B. Q 0 (approx. no heat transfer w/ surroundings) C. Q > 0 (heat transfer into the potato)
18 i-clicker #3 You packed your hot potato in a well-insulated lunch bag with a cold soda and let it sit for 15 minutes. What is the simplest correct first-law balance on the potato for this process? A. B. C. D.
19 Closed System = Control Mass Closed system (Control mass): A fixed amount of mass, and no mass can cross its boundary, but energy can cross its boundary.
20 Open System = Control Volume Open system (control volume): A properly-selected region in space. Usually encloses a device that involves mass flow such as a compressor, turbine, or nozzle. Both mass and energy can cross the boundary of a control volume. An open system (a control volume) with one inlet and one exit.
21 Flow Work in Open Systems Flow Work: Net rate of work done by the entering and exiting fluid to push fluid in or out. Fluid in Pressure = p i Area = A i Velocity = V i Fluid out Pressure = p e Area = A e Velocity = V e
22 Law of Conservation of Energy: The 1 st Law of Thermodynamics Best Balance for Closed system (no mass crosses boundaries; Δ usually = change in time): Depend only on initial and final state of system = Q + W Depend on process Best Balance for Open system, SS (mass can cross boundaries; Δ usually = change in position) : Depend only on state of system at inlet and exit = Q + W cv Depend on process
23 i-clicker #4: Steam enters a rotary turbine and turns a shaft connected to a generator. The inlet and outlet steam ports are approximately at the same height (ignore difference in picture below) but the inlet and exit velocities are not equal. The system is not perfectly insulated. Is the system open or closed? What is the simplest correct energy balance? A. Closed; B. Closed; C. Open; D. Open; E. Open; ΔKE + ΔU = Q + W ΔU = Q + W ΔKE + ΔH = Q + ΔH = Q + W cv ΔH = W W cv
24 i-clicker #5: A tray filled with water at 20 C is put into a freezer. The water turns into ice at - 5 C. Is the system (tray + water) open or closed? What is the simplest correct energy balance? A. Closed; ΔU = Q + W B. Closed; C. Open; ΔH = Q + W cv D. Open;
25 i-clicker #6: Hydrogen and air enter a fuel cell and unused fuel and water exit; the fuel cell produces electric work and waste heat. Is the fuel cell an open or closed system? What is the simplest correct energy balance? A. Closed B. Closed; C. Open; D. Open; ΔU = Q + W ΔU = W ΔH = Q + W cv ΔH = W cv Figure from Fuel Cell Efficiency, a CACHE Module on Energy in the Curriculum.
26 Example Problem A fan is to accelerate quiescent air to a velocity of 10 m/s at a rate of 4 m 3 /s. Determine the minimum power that must be supplied to the fan. The density of air at the entrance conditions is 1.18 kg/m 3. System: Assumptions: 1 st Law:
27 Example Problem Solution:
Chapter 5. Mass and Energy Analysis of Control Volumes. by Asst. Prof. Dr.Woranee Paengjuntuek and Asst. Prof. Dr.Worarattana Pattaraprakorn
Chapter 5 Mass and Energy Analysis of Control Volumes by Asst. Prof. Dr.Woranee Paengjuntuek and Asst. Prof. Dr.Worarattana Pattaraprakorn Reference: Cengel, Yunus A. and Michael A. Boles, Thermodynamics:
Basic overall reaction for hydrogen powering
Fuel Cell Basics Basic overall reaction for hydrogen powering 2H 2 + O 2 2H 2 O Hydrogen produces electrons, protons, heat and water PEMFC Anode reaction: H 2 2H + + 2e Cathode reaction: (½)O 2 + 2H +
ENT 254: Applied Thermodynamics
ENT 54: Applied Thermodynamics Mr. Azizul bin Mohamad Mechanical Engineering Program School of Mechatronic Engineering Universiti Malaysia Perlis (UniMAP) azizul@unimap.edu.my 019-4747351 04-9798679 Chapter
1 st Law Analysis of Control Volume (open system) Chapter 6
1 st Law Analysis of Control Volume (open system) Chapter 6 In chapter 5, we did 1st law analysis for a control mass (closed system). In this chapter the analysis of the 1st law will be on a control volume
Chapter 5. Mass and Energy Analysis of Control Volumes
Chapter 5 Mass and Energy Analysis of Control Volumes Conservation Principles for Control volumes The conservation of mass and the conservation of energy principles for open systems (or control volumes)
Basic overall reaction for hydrogen powering
Fuel Cell Basics Basic overall reaction for hydrogen powering 2H 2 + O 2 2H 2 O Hydrogen produces electrons, protons, heat and water PEMFC Anode reaction: H 2 2H + + 2e Cathode reaction: (½)O 2 + 2H +
Thermodynamics ENGR360-MEP112 LECTURE 7
Thermodynamics ENGR360-MEP11 LECTURE 7 Thermodynamics ENGR360/MEP11 Objectives: 1. Conservation of mass principle.. Conservation of energy principle applied to control volumes (first law of thermodynamics).
Energy and Energy Balances
Energy and Energy Balances help us account for the total energy required for a process to run Minimizing wasted energy is crucial in Energy, like mass, is. This is the Components of Total Energy energy
MASS, MOMENTUM, AND ENERGY EQUATIONS
MASS, MOMENTUM, AND ENERGY EQUATIONS This chapter deals with four equations commonly used in fluid mechanics: the mass, Bernoulli, Momentum and energy equations. The mass equation is an expression of the
CHAPTER 7 ENTROPY. Copyright Hany A. Al-Ansary and S. I. Abdel-Khalik (2014) 1
CHAPTER 7 ENTROPY S. I. Abdel-Khalik (2014) 1 ENTROPY The Clausius Inequality The Clausius inequality states that for for all cycles, reversible or irreversible, engines or refrigerators: For internally-reversible
CHAPTER 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES
Thermodynamics: An Engineering Approach 8th Edition in SI Units Yunus A. Çengel, Michael A. Boles McGraw-Hill, 2015 CHAPTER 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES Lecture slides by Dr. Fawzi Elfghi
CLAUSIUS INEQUALITY. PROOF: In Classroom
Chapter 7 ENTROPY CLAUSIUS INEQUALITY PROOF: In Classroom 2 RESULTS OF CLAUSIUS INEQUALITY For internally reversible cycles δq = 0 T int rev For irreversible cycles δq < 0 T irr A quantity whose cyclic
Two mark questions and answers UNIT I BASIC CONCEPT AND FIRST LAW SVCET
Two mark questions and answers UNIT I BASIC CONCEPT AND FIRST LAW 1. What do you understand by pure substance? A pure substance is defined as one that is homogeneous and invariable in chemical composition
Chapter 5: The First Law of Thermodynamics: Closed Systems
Chapter 5: The First Law of Thermodynamics: Closed Systems The first law of thermodynamics can be simply stated as follows: during an interaction between a system and its surroundings, the amount of energy
Objectives. Conservation of mass principle: Mass Equation The Bernoulli equation Conservation of energy principle: Energy equation
Objectives Conservation of mass principle: Mass Equation The Bernoulli equation Conservation of energy principle: Energy equation Conservation of Mass Conservation of Mass Mass, like energy, is a conserved
Turbine D P. Example 5.6 Air-standard Brayton cycle thermal efficiency
Section 5.6 Engines 5.6 ENGINES ombustion Gas Turbine (Brayton ycle) The typical approach for analysis of air standard cycles is illustrated by the Brayton ycle in Fig. S-5.. To understand the cycle, the
Name: Discussion Section:
CBE 141: Chemical Engineering Thermodynamics, Spring 2017, UC Berkeley Midterm 2 FORM B March 23, 2017 Time: 80 minutes, closed-book and closed-notes, one-sided 8 ½ x 11 equation sheet allowed lease show
Where F1 is the force and dl1 is the infinitesimal displacement, but F1 = p1a1
In order to force the fluid to flow across the boundary of the system against a pressure p1, work is done on the boundary of the system. The amount of work done is dw = - F1.dl1, Where F1 is the force
Week 8. Steady Flow Engineering Devices. GENESYS Laboratory
Week 8. Steady Flow Engineering Devices Objectives 1. Solve energy balance problems for common steady-flow devices such as nozzles, compressors, turbines, throttling valves, mixers, heaters, and heat exchangers
THE FIRST LAW APPLIED TO STEADY FLOW PROCESSES
Chapter 10 THE FIRST LAW APPLIED TO STEADY FLOW PROCESSES It is not the sun to overtake the moon, nor doth the night outstrip theday.theyfloateachinanorbit. The Holy Qur-ān In many engineering applications,
Name: Discussion Section:
CBE 141: Chemical Engineering Thermodynamics, Spring 2017, UC Berkeley Midterm 2 FORM A March 23, 2017 Time: 80 minutes, closed-book and closed-notes, one-sided 8 ½ x 11 equation sheet allowed Please show
Previous lecture. Today lecture
Previous lecture ds relations (derive from steady energy balance) Gibb s equations Entropy change in liquid and solid Equations of & v, & P, and P & for steady isentropic process of ideal gas Isentropic
5/6/ :41 PM. Chapter 6. Using Entropy. Dr. Mohammad Abuhaiba, PE
Chapter 6 Using Entropy 1 2 Chapter Objective Means are introduced for analyzing systems from the 2 nd law perspective as they undergo processes that are not necessarily cycles. Objective: introduce entropy
AAE COMBUSTION AND THERMOCHEMISTRY
5. COMBUSTIO AD THERMOCHEMISTRY Ch5 1 Overview Definition & mathematical determination of chemical equilibrium, Definition/determination of adiabatic flame temperature, Prediction of composition and temperature
The First Law of Thermodynamics. By: Yidnekachew Messele
The First Law of Thermodynamics By: Yidnekachew Messele It is the law that relates the various forms of energies for system of different types. It is simply the expression of the conservation of energy
AME 436. Energy and Propulsion. Lecture 7 Unsteady-flow (reciprocating) engines 2: Using P-V and T-s diagrams
AME 46 Energy and ropulsion Lecture 7 Unsteady-flow (reciprocating) engines : Using - and -s diagrams Outline! Air cycles! What are they?! Why use - and -s diagrams?! Using - and -s diagrams for air cycles!!!!!!
Energy: The ability to cause changes. thermodynamics stems from therme (heat) and dynamis (power).
Energy: The ability to cause changes. thermodynamics stems from therme (heat) and dynamis (power). Thermodynamics: The science of energy. Conservation of energy principle: During an interaction, energy
first law of ThermodyNamics
first law of ThermodyNamics First law of thermodynamics - Principle of conservation of energy - Energy can be neither created nor destroyed Basic statement When any closed system is taken through a cycle,
Prof. Mario L. Ferrari
Sustainable Energy Mod.1: Fuel Cells & Distributed Generation Systems Dr. Ing. Mario L. Ferrari Thermochemical Power Group (TPG) - DiMSET University of Genoa, Italy Lesson II Lesson II: fuel cells (electrochemistry)
BME-A PREVIOUS YEAR QUESTIONS
BME-A PREVIOUS YEAR QUESTIONS CREDITS CHANGE ACCHA HAI TEAM UNIT-1 Introduction: Introduction to Thermodynamics, Concepts of systems, control volume, state, properties, equilibrium, quasi-static process,
Thermodynamics: An Engineering Approach Seventh Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, Chapter 7 ENTROPY
Thermodynamics: An Engineering Approach Seventh Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 7 ENTROPY Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction
Applied Thermodynamics for Marine Systems Prof. P. K. Das Department of Mechanical Engineering Indian Institute of Technology, Kharagpur
Applied Thermodynamics for Marine Systems Prof. P. K. Das Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture No - 03 First Law of Thermodynamics (Open System) Good afternoon,
Turbomachinery. Hasan Ozcan Assistant Professor. Mechanical Engineering Department Faculty of Engineering Karabuk University
Turbomachinery Hasan Ozcan Assistant Professor Mechanical Engineering Department Faculty of Engineering Karabuk University Introduction Hasan Ozcan, Ph.D, (Assistant Professor) B.Sc :Erciyes University,
ENTROPY. Chapter 7. Mehmet Kanoglu. Thermodynamics: An Engineering Approach, 6 th Edition. Yunus A. Cengel, Michael A. Boles.
Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 7 ENTROPY Mehmet Kanoglu Copyright The McGraw-Hill Companies, Inc. Permission required
Thermodynamics. AP Physics B
Thermodynamics AP Physics B Important Distinctions Thermodynamics study of processes in which energy is transferred as heat and work. There is a difference between heat and work: Heat is energy transferred
Introduction CHAPTER Prime Movers. 1.2 Sources of Energy
Introduction CHAPTER 1 1.1 Prime Movers Prime mover is a device which converts natural source of energy into mechanical work to drive machines for various applications. In olden days, man had to depend
Applied Thermodynamics for Marine Systems Prof. P. K. Das Department of Mechanical Engineering Indian Institute of Technology, Kharagpur
Applied Thermodynamics for Marine Systems Prof. P. K. Das Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture 2 First Law of Thermodynamics (Closed System) In the last
I. (20%) Answer the following True (T) or False (F). If false, explain why for full credit.
I. (20%) Answer the following True (T) or False (F). If false, explain why for full credit. Both the Kelvin and Fahrenheit scales are absolute temperature scales. Specific volume, v, is an intensive property,
M E 320 Professor John M. Cimbala Lecture 23
M E 320 Professor John M. Cimbala Lecture 23 Today, we will: Discuss diffusers and do an example problem Begin discussing pumps, and how they are analyzed in pipe flow systems D. Diffusers 1. Introduction.
UNIFIED ENGINEERING Fall 2003 Ian A. Waitz
Ian A. Waitz Problem T6. (Thermodynamics) Consider the following thermodynamic cycle. Assume all processes are quasi-static and involve an ideal gas. 3 p Const. volume heat addition 2 adiabatic expansion
Thermodynamics of solids 5. Unary systems. Kwangheon Park Kyung Hee University Department of Nuclear Engineering
Thermodynamics of solids 5. Unary systems Kwangheon ark Kyung Hee University Department of Nuclear Engineering 5.1. Unary heterogeneous system definition Unary system: one component system. Unary heterogeneous
Thermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011.
Thermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 7 ENTROPY Mehmet Kanoglu University of Gaziantep Copyright The McGraw-Hill
CLASS Fourth Units (Second part)
CLASS Fourth Units (Second part) Energy analysis of closed systems Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display. MOVING BOUNDARY WORK Moving boundary work (P
Name: Discussion Section:
CBE 141: Chemical Engineering Thermodynamics, Spring 2018, UC Berkeley Midterm 1 February 13, 2018 Time: 80 minutes, closed-book and closed-notes, one-sided 8 ½ x 11 equation sheet allowed Please show
Thermal Energy Final Exam Fall 2002
16.050 Thermal Energy Final Exam Fall 2002 Do all eight problems. All problems count the same. 1. A system undergoes a reversible cycle while exchanging heat with three thermal reservoirs, as shown below.
Direct Energy Conversion: Fuel Cells
Direct Energy Conversion: Fuel Cells References and Sources: Direct Energy Conversion by Stanley W. Angrist, Allyn and Beacon, 1982. Fuel Cell Systems, Explained by James Larminie and Andrew Dicks, Wiley,
Chapter 7. Dr Ali Jawarneh. Department of Mechanical Engineering Hashemite University
Chapter 7 ENTROPY Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Objectives Apply the second law of thermodynamics to processes. Define a new property called entropy to quantify
Introduction to Chemical Engineering Thermodynamics. Chapter 7. KFUPM Housam Binous CHE 303
Introduction to Chemical Engineering Thermodynamics Chapter 7 1 Thermodynamics of flow is based on mass, energy and entropy balances Fluid mechanics encompasses the above balances and conservation of momentum
7. Development of the 2nd Law
7-1 7. Development of the 2nd Law 7.1 1st Law Limitations The 1 st Law describes energy accounting. Once we have a process (or string of processes) we can calculate the relevant energy interactions. The
MAHALAKSHMI ENGINEERING COLLEGE
MAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI-621213. Department: Mechanical Subject Code: ME2202 U N IT - 1 Semester: III Subject Name: ENGG. THERMODYNAMICS 1. 1 kg of gas at 1.1 bar, 27 o C is compressed
Jet Aircraft Propulsion Prof. Bhaskar Roy Prof A M Pradeep Department of Aerospace Engineering Indian Institute of Technology, Bombay
Jet Aircraft Propulsion Prof. Bhaskar Roy Prof A M Pradeep Department of Aerospace Engineering Indian Institute of Technology, Bombay Module No. #01 Lecture No. # 07 Jet Engine Cycles For Aircraft propulsion
Chapter Four fluid flow mass, energy, Bernoulli and momentum
4-1Conservation of Mass Principle Consider a control volume of arbitrary shape, as shown in Fig (4-1). Figure (4-1): the differential control volume and differential control volume (Total mass entering
SPH 302 THERMODYNAMICS
THERMODYNAMICS Nyongesa F. W., PhD. e-mail: fnyongesa@uonbi.ac.ke 1 Course Outline Lecture 1: Thermodynamic concepts & Zeroth Law Lecture 2: 1 ST Law Lecture 3: 2 ND Law Lecture 4: Entropy and 2 ND Law
MAE 11. Homework 8: Solutions 11/30/2018
MAE 11 Homework 8: Solutions 11/30/2018 MAE 11 Fall 2018 HW #8 Due: Friday, November 30 (beginning of class at 12:00p) Requirements:: Include T s diagram for all cycles. Also include p v diagrams for Ch
Chapter 7. Entropy: A Measure of Disorder
Chapter 7 Entropy: A Measure of Disorder Entropy and the Clausius Inequality The second law of thermodynamics leads to the definition of a new property called entropy, a quantitative measure of microscopic
SPH 302 THERMODYNAMICS
THERMODYNAMICS Nyongesa F. W., PhD. e-mail: fnyongesa@uonbi.ac.ke 1 Objectives Explain the Laws of thermodynamics & their significance Apply laws of thermodynamics to solve problems relating to energy
CHM 111 Dr. Kevin Moore
CHM 111 Dr. Kevin Moore Kinetic Energy Energy of motion E k 1 2 mv 2 Potential Energy Energy of position (stored) Law of Conservation of Energy Energy cannot be created or destroyed; it can only be converted
COMBUSTION OF FUEL 12:57:42
COMBUSTION OF FUEL The burning of fuel in presence of air is known as combustion. It is a chemical reaction taking place between fuel and oxygen at temperature above ignition temperature. Heat is released
Lecture Presentation. Chapter 20. Electrochemistry. James F. Kirby Quinnipiac University Hamden, CT Pearson Education, Inc.
Lecture Presentation Chapter 20 James F. Kirby Quinnipiac University Hamden, CT is the study of the relationships between electricity and chemical reactions. It includes the study of both spontaneous and
Lecture 35: Vapor power systems, Rankine cycle
ME 00 Thermodynamics I Spring 015 Lecture 35: Vapor power systems, Rankine cycle Yong Li Shanghai Jiao Tong University Institute of Refrigeration and Cryogenics 800 Dong Chuan Road Shanghai, 0040, P. R.
The need for something else: Entropy
Lecture 27 Goals: Ch. 18 ualitatively understand 2 nd Law of Thermodynamics Ch. 19 Understand the relationship between work and heat in a cycling process Follow the physics of basic heat engines and refrigerators.
Electrochemical Cells
Electrochemistry Electrochemical Cells The Voltaic Cell Electrochemical Cell = device that generates electricity through redox rxns 1 Voltaic (Galvanic) Cell An electrochemical cell that produces an electrical
Thermodynamics II. Week 9
hermodynamics II Week 9 Example Oxygen gas in a piston cylinder at 300K, 00 kpa with volume o. m 3 is compressed in a reversible adiabatic process to a final temperature of 700K. Find the final pressure
Introduction to Turbomachinery
1. Coordinate System Introduction to Turbomachinery Since there are stationary and rotating blades in turbomachines, they tend to form a cylindrical form, represented in three directions; 1. Axial 2. Radial
The exergy of asystemis the maximum useful work possible during a process that brings the system into equilibrium with aheat reservoir. (4.
Energy Equation Entropy equation in Chapter 4: control mass approach The second law of thermodynamics Availability (exergy) The exergy of asystemis the maximum useful work possible during a process that
Theory of turbomachinery. Chapter 1
Theory of turbomachinery Chater Introduction: Basic Princiles Take your choice of those that can best aid your action. (Shakeseare, Coriolanus) Introduction Definition Turbomachinery describes machines
ENERGY TRANSFER BY WORK: Electrical Work: When N Coulombs of electrical charge move through a potential difference V
Weight, W = mg Where m=mass, g=gravitational acceleration ENERGY TRANSFER BY WOR: Sign convention: Work done on a system = (+) Work done by a system = (-) Density, ρ = m V kg m 3 Where m=mass, V =Volume
Handout 12: Thermodynamics. Zeroth law of thermodynamics
1 Handout 12: Thermodynamics Zeroth law of thermodynamics When two objects with different temperature are brought into contact, heat flows from the hotter body to a cooler one Heat flows until the temperatures
E40M Charge, Current, Voltage and Electrical Circuits. M. Horowitz, J. Plummer, R. Howe 1
E40M Charge, Current, Voltage and Electrical Circuits M. Horowitz, J. Plummer, R. Howe 1 Understanding the Solar Charger Lab Project #1 We need to understand how: 1. Current, voltage and power behave in
EXAM # 1 ME 300 SP2017
CIRCLE YOUR LECTURE BELOW: 8:3 am :3 am 3:3 pm Prof. Lucht Prof. Chen Prof. Goldenstein EXAM # ME 3 SP7 INSTRUCTIONS. Please place all your electronics, including but not limited to cell phones, computers,
Department of Mechanical Engineering ME 322 Mechanical Engineering Thermodynamics. Lecture 26. Use of Regeneration in Vapor Power Cycles
Department of Mechanical Engineering ME 322 Mechanical Engineering Thermodynamics Lecture 2 Use of Regeneration in Vapor Power Cycles What is Regeneration? Goal of regeneration Reduce the fuel input requirements
Objects usually are charged up through the transfer of electrons from one object to the other.
1 Part 1: Electric Force Review of Vectors Review your vectors! You should know how to convert from polar form to component form and vice versa add and subtract vectors multiply vectors by scalars Find
First Law of Thermodynamics
CH2303 Chemical Engineering Thermodynamics I Unit II First Law of Thermodynamics Dr. M. Subramanian 07-July-2011 Associate Professor Department of Chemical Engineering Sri Sivasubramaniya Nadar College
UNIT8-DAY4-LaB1230. Thinking Like a Chemist About Electrochemistry III. Potential, Free Energy & K UNIT8 DAY4 IMPORTANT INFORMATION
UNIT8-DAY4-LaB1230 Page 1 UNIT8-DAY4-LaB1230 Monday, April 22, 2013 3:35 PM Thinking Like a Chemist About Electrochemistry III Potential, Free Energy & K UNIT8 DAY4 CH302 Vanden Bout/LaBrake Spring 2012
ME Thermodynamics I
Homework - Week 01 HW-01 (25 points) Given: 5 Schematic of the solar cell/solar panel Find: 5 Identify the system and the heat/work interactions associated with it. Show the direction of the interactions.
"Thermodynamic Analysis of Processes for Hydrogen Generation by Decomposition of Water"
"Thermodynamic Analysis of Processes for Hydrogen Generation by Decomposition of Water" by John P. O'Connell Department of Chemical Engineering University of Virginia Charlottesville, VA 22904-4741 A Set
Jet Aircraft Propulsion Prof. Bhaskar Roy Prof. A.M. Pradeep Department of Aerospace Engineering
Jet Aircraft Propulsion Prof. Bhaskar Roy Prof. A.M. Pradeep Department of Aerospace Engineering Indian Institute of Technology, IIT Bombay Module No. # 01 Lecture No. # 08 Cycle Components and Component
Thermodynamics I Spring 1432/1433H (2011/2012H) Saturday, Wednesday 8:00am - 10:00am & Monday 8:00am - 9:00am MEP 261 Class ZA
Thermodynamics I Spring 1432/1433H (2011/2012H) Saturday, Wednesday 8:00am - 10:00am & Monday 8:00am - 9:00am MEP 261 Class ZA Dr. Walid A. Aissa Associate Professor, Mech. Engg. Dept. Faculty of Engineering
Vanden Bout/LaBrake. THERMODYNAMICS Quantifying Heat Flow Physical Change. Important Information EXAM 3 WRAPPER POSTED LATER TODAY OPEN 1 WEEK
UNIT4DAY2-LaB Page 1 UNIT4DAY2-LaB Monday, November 12, 2012 10:00 PM Vanden Bout/LaBrake CH301 THERMODYNAMICS Quantifying Heat Flow Physical Change UNIT 4 Day 2 Important Information LM28 & 29 DUE Th
Spring_#8. Thermodynamics. Youngsuk Nam
Spring_#8 Thermodynamics Youngsuk Nam ysnam1@khu.ac.krac kr Ch.7: Entropy Apply the second law of thermodynamics to processes. Define a new property called entropy to quantify the secondlaw effects. Establish
Electrochemical System
Electrochemical System Topic Outcomes Week Topic Topic Outcomes 8-10 Electrochemical systems It is expected that students are able to: Electrochemical system and its thermodynamics Chemical reactions in
Chemistry: The Central Science. Chapter 20: Electrochemistry
Chemistry: The Central Science Chapter 20: Electrochemistry Redox reaction power batteries Electrochemistry is the study of the relationships between electricity and chemical reactions o It includes the
Today lecture. 1. Entropy change in an isolated system 2. Exergy
Today lecture 1. Entropy change in an isolated system. Exergy - What is exergy? - Reversible Work & Irreversibility - Second-Law Efficiency - Exergy change of a system For a fixed mass For a flow stream
(Refer Slide Time: 0:28)
Engineering Thermodynamics Professor Jayant K Singh Department of Chemical Engineering Indian Institute of Technology Kanpur Lecture 08 Examples on basic concept & energy balance Welcome back! Myself Parul
Dishwasher. Heater. Homework Solutions ME Thermodynamics I Spring HW-1 (25 points)
HW-1 (25 points) (a) Given: 1 for writing given, find, EFD, etc., Schematic of a household piping system Find: Identify system and location on the system boundary where the system interacts with the environment
Engineering Thermodynamics. Chapter 5. The Second Law of Thermodynamics
5.1 Introduction Chapter 5 The Second aw of Thermodynamics The second law of thermodynamics states that processes occur in a certain direction, not in just any direction. Physical processes in nature can
PTT 277/3 APPLIED THERMODYNAMICS SEM 1 (2013/2014)
PTT 77/3 APPLIED THERMODYNAMICS SEM 1 (013/014) 1 Energy can exist in numerous forms: Thermal Mechanical Kinetic Potential Electric Magnetic Chemical Nuclear The total energy of a system on a unit mass:
FUEL CELLS: INTRODUCTION
FUEL CELLS: INTRODUCTION M. OLIVIER marjorie.olivier@fpms.ac.be 19/5/8 A SIMPLE FUEL CELL Two electrochemical half reactions : H 1 O H + + H + e + + e H O These reactions are spatially separated: Electrons:
Handout 12: Thermodynamics. Zeroth law of thermodynamics
1 Handout 12: Thermodynamics Zeroth law of thermodynamics When two objects with different temperature are brought into contact, heat flows from the hotter body to a cooler one Heat flows until the temperatures
Principles of Food and Bioprocess Engineering (FS 231) Problems on Heat Transfer
Principles of Food and Bioprocess Engineering (FS 1) Problems on Heat Transfer 1. What is the thermal conductivity of a material 8 cm thick if the temperature at one end of the product is 0 C and the temperature
where = rate of change of total energy of the system, = rate of heat added to the system, = rate of work done by the system
The Energy Equation for Control Volumes Recall, the First Law of Thermodynamics: where = rate of change of total energy of the system, = rate of heat added to the system, = rate of work done by the system
Isentropic Efficiency in Engineering Thermodynamics
June 21, 2010 Isentropic Efficiency in Engineering Thermodynamics Introduction This article is a summary of selected parts of chapters 4, 5 and 6 in the textbook by Moran and Shapiro (2008. The intent
2. Describe the second law in terms of adiabatic and reversible processes.
Lecture #3 1 Lecture 3 Objectives: Students will be able to: 1. Describe the first law in terms of heat and work interactions.. Describe the second law in terms of adiabatic and reversible processes. 3.
Fernando O. Raineri. Office Hours: MWF 9:30-10:30 AM Room 519 Tue. 3:00-5:00 CLC (lobby).
Fernando O. Raineri Office Hours: MWF 9:30-10:30 AM Room 519 Tue. 3:00-5:00 CLC (lobby). P1) What is the reduction potential of the hydrogen electrode g bar H O aq Pt(s) H,1 2 3 when the aqueous solution
Earlier Topics. Introduction to Cryogenic Engineering An introductory knowledge of Cryogenic Engineering.
8 1 Earlier Topics Introduction to Cryogenic Engineering An introductory knowledge of Cryogenic Engineering. Properties of Cryogenic Fluids Properties of Cryogens, T s diagram, Hydrogen, Helium. Properties
w = -nrt hot ln(v 2 /V 1 ) nrt cold ln(v 1 /V 2 )[sincev/v 4 3 = V 1 /V 2 ]
![w = -nrt hot ln(v 2 /V 1 ) nrt cold ln(v 1 /V 2 )[sincev/v 4 3 = V 1 /V 2 ]](/thumbs/85/91320285.jpg "w = -nrt hot ln(v 2 /V 1 ) nrt cold ln(v 1 /V 2 )[sincev/v 4 3 = V 1 /V 2 ]")
Chemistry 433 Lecture 9 Entropy and the Second Law NC State University Spontaneity of Chemical Reactions One might be tempted based on the results of thermochemistry to predict that all exothermic reactions
Ch 18 Electrochemistry OIL-RIG Reactions
Ch 18 Electrochemistry OIL-RIG Reactions Alessandro Volta s Invention Modified by Dr. Cheng-Yu Lai Daily Electrochemistry Appliactions Electrochemistry: The area of chemistry that examines the transformations
Ch. 13 Fundamentals of Electrochemistry
Ch. 13 Fundamentals of Electrochemistry 13.1 13-1. Basic Concepts of electrochemistry redox reaction : reactions with electron transfer oxidized : loses electrons reduced : gains electrons Fe 3+ + V 2+
Electrochemistry. Goal: Understand basic electrochemical reactions. Half Cell Reactions Nernst Equation Pourbaix Diagrams.
Electrochemistry Goal: Understand basic electrochemical reactions Concepts: Electrochemical Cell Half Cell Reactions Nernst Equation Pourbaix Diagrams Homework: Applications Battery potential calculation
4. All questions are NOT ofequal value. Marks available for each question are shown in the examination paper.
THE UNIVERSITY OF NEW SOUTH WALES SCHOOL OF PHYSICS \1111~11\llllllllllllftllll~flrllllllllll\11111111111111111 >014407892 PHYS2060 THER1\1AL PHYSICS FINAL EXAMINATION SESSION 2 - NOVEMBER 2010 I. Time