VGG UFLWU SPEC SAMPLE 2. 1 Table of Contents 2. 2 Record of Revisions 3. 3 Module Numbering System 4. 4 Application 5.

Size: px

Start display at page:

Download "VGG UFLWU SPEC SAMPLE 2. 1 Table of Contents 2. 2 Record of Revisions 3. 3 Module Numbering System 4. 4 Application 5."

Mark Hill
5 years ago
Views:

2 VGG UFLWU SPEC SAMPLE 2 1. Table of Contents No. Contents Page 1 Table of Contents 2 2 Record of Revisions 3 3 Module Numbering System 4 4 Application 5 5 Features 5 6 General Specifications 5 7 Absolute Maximum Ratings 6 8 Electrical Characteristics 7 9 Block Diagram 8 10 Input / Output Terminals Pin Assignment 9 11 Interface Timing Optical Characteristics Reliability Test Packaging Precautions Outline Drawing Definition of Labels Incoming Inspection Standards 27

3 VGG UFLWU SPEC SAMPLE 3 2. Record of Revisions Rev. Comments Page Date 1 Preliminary Specification was first issued All 12/13 16

4 VGG UFLWU SPEC SAMPLE 4 3. Module Numbering System V G G U F L W U

5 VGG UFLWU SPEC SAMPLE 5 4. Application This specification is applied to the 5.7 inch VGA supported TFT-LCD module, and can display true 262,144 colors(6 bit/ color). The module is designed for OA, Car TV application and other electronic products which require flat panel display of digital signal interface. This module is composed of a 5.7 TFT-LCD panel, a driver circuit and LED backlight unit 5. Features - VGA ( pixels) resolution. - LVDS Receiver 18 bit Interface - Dot inversion mode with stripe type. - Ultra Wide View Polarizer 6. General Specifications Item Specifications Unit Screen Size 5.7 (Diagonal) inch Display Format 640RGB(H) 480(V) dot Active Area 115.2(H) 86.4(V) mm Pixel Size 0.060(H) 0.180(V) mm Pixel Configuration RGB Vertical Stripe - TN Type Display Mode Transmissive Mode Normally White - Surface Treatment Anti-Glare - Viewing Direction 6 O clock (The Gray Inversion will appear at this direction) - Outline Dimension 144.0(W) 104.6(H) 13.0(D) mm LVDS Receiver IC THine THC63LVDF84C - Weight 151 g RoHS Compliance Evervision certifies this product to be in compliance with European Union Directive 2011/65/EU on the restriction of certain hazardous substances in electrical and electronic -

6 VGG UFLWU SPEC SAMPLE 6 7. Absolute Maximum Ratings 7.1 Absolute Ratings of Environment Item Symbol Min. Value Max. Unit Note Storage Temperature T ST C (1)(2) Operating Ambient Temperature T OP C (1)(2) Note1: Background color changes slightly depending on ambient temperature. This phenomenon is reversible. Note2: Please refer to item of RELIABILITY. 7.2 Electrical Absolute Ratings TFT-LCD Module Item Symbol Min. Value (Ta=25±2 C, GND=V SS =0V) Max. Unit Power Supply Voltage V CC V - LVDS Driver Output Voltage V CC V - Note Backlight Unit (Ta=25±2 C) Item Symbol Value Min. Max. Unit Note Current of Backlight Unit I B ma (1) Reverse voltage V R V (1) Note (1) Permanent damage to the device may occur if maximum values are exceeded or reverse voltage is loaded.

7 VGG UFLWU SPEC SAMPLE 7 8. Electrical Characteristics 8.1 TFT-LCD Module (Ta=25±2 C) Item Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage VCC V - Power Supply Current ICC ma - Differential Input High Threshold Voltage Differential Input Low Threshold Voltage VTH mv - VTL mv - Power Consumption PL - (742.5) 1040 mw (1) Frame Frequency FV Hz - Dot Clock DCLK MHz - Note (1) The specified power consumption is under the conditions at V CC =3.3V, F V =60Hz, whereas a power dissipation check pattern below is displayed. Black Pattern / 0 Gray Active Area 8.2 Backlight Unit (Ta=25±2 C) Item Symbol Value Min. Typ. Max. Unit Note Current of Backlight Unit I B ma - Voltage of Backlight Unit V B V I B =300mA Power Consumption P BL - (2.88) - W I B =300mA LED Life Time(25 ) hr -

8 VGG UFLWU SPEC SAMPLE 8 9. Block Diagram 9.1 TFT-LCD Module with Backlight Unit 5.7 inch TFT LCD Panel 640(RGB)x480 Pixel 3S10P LED BLU Source Driver with build-in Timing controller Gate Driver LVDS Receiver DC/DC Converter TFT Connector Backlight Connector INTERFACE Backlight Power Input

9 VGG UFLWU SPEC SAMPLE Input / Output Terminals Pin Assignment 10.1 TFT-LCD Module Connector: HIROSE DF19G-20P-1H or equivalent Pin No. Symbol I/O Description 1 V CC I +3.3V power supply 2 V CC I +3.3V power supply 3 V SS I Ground 4 V SS I Ground 5 RIN0- I Negative LVDS differential data input 6 RIN0+ I Positive LVDS differential data input 7 V SS I Ground 8 RIN1- I Negative LVDS differential data input 9 RIN1+ I Positive LVDS differential data input 10 V SS I Ground 11 RIN2- I Negative LVDS differential data input 12 RIN2+ I Positive LVDS differential data input 13 V SS I Ground 14 RCLK- I Negative LVDS differential clock input 15 RCLK+ I Positive LVDS differential clock input 16 V SS I Ground 17 NC I Not connection 18 NC I Not connection 19 REV I Selection signal for horizontal/ vertical scanning direction. Note (1) 20 V SS I Ground

10 VGG UFLWU SPEC SAMPLE 10 Note (1) EVERVISION EVERVISION REV="L" REV="H" 10.2 Backlight Unit Connector: JST BHSR-02VS-1(N) or equivalent Pin No. Symbol I/O Description Wire Color 1 VLEDA I Backlight LED Anode. Red 2 VLEDC I Backlight LED Cathode. Black

11 VGG UFLWU SPEC SAMPLE Color Data Input Assignment The brightness of each primary color(red, green and blue) is based on the 6 bit gray scale data input for the color. The higher the binary input, the brighter the color. The table provides the assignment of color versus data input. Data Signal Color Red Green Blue D05 D04 D03 D02 D01 D00 D15 D14 D13 D12 D11 D10 D25 D24 D23 D22 D21 D20 Black Red Green Basic Colors Blue Cyan Magenta Yellow White Red(0) / Dark Red(1) Red(2) Gray Scale Of RED : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Red(61) Red(62) Red(63) Green(0) / Dark Green(1) Green(2) Gray Scale Of Green : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Green(61) Green(62) Green(63) Blue(0) / Dark Blue(1) Blue(2) Gray Scale Of Blue : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Blue(61) Blue(62) Blue(63)

12 VGG UFLWU SPEC SAMPLE Power ON/OFF Sequence POWER SEQUENCE TABLE Value Parameter Min. Typ Max. Units T ms T ms T ms T ms T ms T ms

13 VGG UFLWU SPEC SAMPLE Interface Timing 11.1 Input Signal Characteristics

14 VGG UFLWU SPEC SAMPLE LVDS Switching Characteristics

15 VGG UFLWU SPEC SAMPLE Waveform Clock and Data input waveforms Data input format for RGB Mode The HS & VS timing of the ODD/EVEN field.

16 VGG UFLWU SPEC SAMPLE LVDS AC Timing

17 VGG UFLWU SPEC SAMPLE Optical Characteristics The optical characteristics should be measured in a dark environment ( 1 lux) or equivalent state with the methods shown in Note (4). Item Symbol Conditions Min. Typ. Max. Unit Note Contrast Ratio CR 200 (350) - - (2) Response Time T R ms T F ms (3) Luminance(Center) Y cd/m 2 (4) Brightness uniformity BUNI 80 (85) - % (5) Red Rx x =0, Y = Ry Viewing Normal Color Green Gx Angle Gy Chromaticity Blue White Bx By Wx Wy (1),(4) Viewing Angle Horizontal Vertical x + 60 (80) - x - 60 (80) - CR 10 Y + 60 (80) - Y - 60 (80) - deg.

18 VGG UFLWU SPEC SAMPLE 18 Note (1) Definition of Viewing Angle ( x, y): Normal x = y = 0º y- y X- = 90º x- x x y+ 12 o clock direction y+ = 90º 6 o clock y- = 90º y- x+ X+ = 90º Note (2) Definition of Contrast Ratio (CR): Note (3) Definition of Response Time (T R, T F ): White White 100% 90% Optical Response 10% Black 0% Time T R T F

19 VGG UFLWU SPEC SAMPLE 19 Note (4) Measurement Set-Up: The LCD module should be stabilized at a given temperature for 30 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a dark room or equivalent condition. LCD Module LCD Panel Center of the Screen Photometer (TOPCON BM-7 Fast) Field of View = 1º 500 mm Light Shield Room (Ambient Luminance < 1 lux) Note (5) Definition of brightness uniformity Brightness uniformity=(min Luminance of 9 points)/(max Luminance of 9 points) 100%

20 VGG UFLWU SPEC SAMPLE Reliability Test No. Test Items Test Condition Remark 1 High Temperature Storage Test T a = hours (1),(3),(4) 2 Low Temperature Storage Test T a = hours (1),(3),(4) High Temperature Operation Test Low Temperature Operation Test High Temperature and High Humidity Operation Test Electro Static Discharge Test (non-operating) Mechanical Shock Test (non-operating) Vibration Test (non-operating) Thermal Shock Test (non-operating) T S = hours (2),(3),(4) T a = hours (1),(3),(4) (5) T a =60 90%RH 240 hours (3),(4) -Panel Surface/Top Case : 150pF, 330Ω Air: ±15kV, Contact: ±8kV Half sine wave, 100G, 6ms 3 times shock of each six surfaces Sine wave:10 ~ 55 ~ 10Hz amplitude:1.5mm 3 axis,2 hours/axis (3) (3) (3) -30 (30min) ~ 80 (30min),10 cycles (3),(4) 10 Drop Test(with Carton) Height: 80cm 1 corner, 3 edges, 6 surfaces (3) Note 1:Ta is the ambient temperature of samples. Note 2:Ts is the temperature of panel s surface. Note 3:In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guarantees operation, but don t guarantee all of the cosmetic specification. Note 4:Before cosmetic and function test, the product must have enough recovery time, at least 2 hours at room temperature. Note 5:When OP reaches -30 degree, the reaction of the display will be slower. However, this phenomenon is reversible after the ambient temperature returns to higher values.

21 VGG UFLWU SPEC SAMPLE Packaging PARTS LIST ITEM SIZE(LxWxH) unit:mm MATERIAL Q.T.Y NOTE 1 STATIC SHIEDING BAGS 300.0x145.0x EPE PAD 345.0x30.0x20.0 EPE 8 3 CARD BOARD 345.0x150.0x3.5 CARTON 6 4 CARD BOARD 450.0x23.0x150.0 CARTON 16 5 INTERNAL BOX 455.0x350.0x164.0 CARTON 2 6 EXTERNAL BOX 475.0x370.0x375.0 CARTON 1 7 PRODUCT 144.0x104.6x13 60

22 VGG UFLWU SPEC SAMPLE Precautions 15.1 Assembly and Handling Precautions (1) Do not apply rough force such as bending or twisting to the module during assembly. (2) It s recommended to assemble or to install a module into the user s system in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) Don t apply pressure or impulse to the module to prevent the damage of LCD panel and Backlight. (4) Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the damage and latch-up of the CMOS LSI chips. (5) Do not plug in or pull out the I/F connector while the module is in operation. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) Moisture can easily penetrate into LCD module and may cause the damage during operation. (9) High temperature or humidity may deteriorate the performance of LCD module. Please store LCD module in the specified storage conditions. (10) When ambient temperature is lower than 10ºC, the display quality might be reduced. For example, the response time will become slow Safety Precautions (1) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (2) After the module s end of life, it is not harmful in case of normal operation and storage Terms of Warrant (1) Acceptance inspection period The period is within one month after the arrival of contracted commodity at the buyer s factory site. (2) Applicable warrant period The period is within twelve months since the date of shipping out under normal using and storage conditions.

23 VGG UFLWU SPEC SAMPLE Caution This Evervision LCD module has been specifically designed for use only in electronic devices in the areas of audio control, office automation,industrial control, home appliances, etc. The modules should not be used in applications where module failure could result in physical harm or loss of life, and Evervision expressly disclaims any and all liability relating in any way to the use of the module in such applications.

24 VGG UFLWU SPEC SAMPLE Outline Drawing

25 VGG UFLWU SPEC SAMPLE Definition of Labels The bar code nameplate is pasted on each module as illustration, and its definitions are as following explanation. VGG UFLWU ABCDEFGHIJKL (a) Module Name:VGG UFLWU (b) Serial ID: A B C D E F G H I J K L Serial No. Factory Code Manufactured Date Screen Size Serial ID includes the information as below: (a) Screen size (Diagonal): Inch Code (ABCD) (b) Manufactured Date: Year, Month, Day (EFG) Year (E) Year Mark Year Mark A B C D E F G H I J

26 VGG UFLWU SPEC SAMPLE 26 Month (F) Month Jan. Feb. Mar. Apr. May Jun. Jul. Aug. Sep. Oct. Nov. Dec. Mark A B C Day (G) Day Mark A B C D E F G Day Mark H I J K L M N O P Q R S T U V (c) Factory Code (H): For EVERVISION internal use. (d) Serial No. (IJKL): Manufacturing sequence of product, for example: 0001~9999.

27 VGG UFLWU SPEC SAMPLE Incoming Inspection Standards 18.1 The environmental condition of inspection The environmental condition and visual inspection shall be conducted as below. (1) Ambient temperature 25 ± 5 (2) Humidity: 45 ~ 65 % RH (3) Viewing distance is approximately 30 ~ 40 cm (4)Viewing angle is normal to the LCD panel as Fig _1 ( ± 45 ) (5) Ambient Illumination: 300 ~ 500 Lux for external appearance inspection 18.2 The defects classify of AQL as following: (1) Test method :According to ANSI/ASQC Z 1.4.General Inspection Level Ⅱ take a single time (2) The defects classify of AQL as following: Class of AQL Definition defects Major 0.65% Minor 1.5% It is defect that is likely to result in failure or to reduce materially the usability of the intended function. It is a defect that will not result in functioning problem with deviation classified.

28 VGG UFLWU SPEC SAMPLE Inspection Parameters

VGG644804-6UFLWU SPEC SAMPLE 29 Item Specification/Description

(non-operating or operating) mura Weak defect will be defined

29 VGG UFLWU SPEC SAMPLE 29 Item Specification/Description Note Has the non-uniform phenomenon mura External Inspection (non-operating or operating) mura Weak defect will be defined as mura if it can be observed through ND filter 6% 6% ND filter

30 VGG UFLWU SPEC SAMPLE 30

31 VGG UFLWU SPEC SAMPLE 31 Note1. The definition of dot defect : The dot defect was judged after repair and the size of a defective dot over 1/2 of whole dot is regarded as one defective dot. Note2. W L Note3. D:Diameter D=(a+b)/2 Note4. Bright dot is defined through 2% transmission ND Filter as following. Note5. ADJACENT DOT

VGG644804-6UFLWU SPEC SAMPLE 32 Note6. B:BM A:AA Note7. A area : Without any defect point effect on normal operation. B area : None-specify 18.4 Handling of LCM (1)Don't give external shock.

32 VGG UFLWU SPEC SAMPLE 32 Note6. B:BM A:AA Note7. A area : Without any defect point effect on normal operation. B area : None-specify 18.4 Handling of LCM (1)Don't give external shock. (2)Don't apply excessive force on the surface. (3)Liquid in LCD is hazardous substance. Must not lick and swallow. when the liquid is attach to your hand, skin, cloth etc. Wash it out thoroughly and immediately. (4)Don't operate it above the absolute maximum rating. (5)Don't disassemble the LCM.

VGG UFLWN SPEC SAMPLE 2. 1 Table of Contents 2. 2 Record of Revisions 3. 3 Module Numbering System 4. 4 Application 5.

VGG UFLWN SPEC SAMPLE 2. 1 Table of Contents 2. 2 Record of Revisions 3. 3 Module Numbering System 4. 4 Application 5. VGG804807-6UFLWN SPEC SAMPLE 2 1. Table of Contents No. Contents Page 1 Table of Contents 2 2 Record of Revisions 3 3 Module Numbering System 4 4 Application 5 5 Features 5 6 General Specifications 5 7