CHIMEI INNOLUX DISPLAY CORPORATION

Size: px

Start display at page:

Download "CHIMEI INNOLUX DISPLAY CORPORATION"

Oswin French
6 years ago
Views:

1 DISPLAY CORPORATION LCD MODULE SPECIFICATION Customer: Model Name: AT043TN25 V.2 Date: 2010/09/15 Version: 01 Preliminary Specification Final Specification For Customer s Acceptance Approved by Comment Approved by Reviewed by Prepared by Hans Chen James Yu Charlie Chou David Lee 2010/11/ /11/ /11/04

3 Contents 1. General Specifications Pin Assignment TFT LCD Panel Driving Section Operation Specifications Absolute Maximum Ratings Typical operation conditions Backlight Driving Conditions Power Sequence Timing Characteristics Timing Conditions Timing Diagram Optical Specifications 9 5. Reliability Test Items General Precautions Safety Handling Static Electricity Storage Cleaning Mechanical Drawing Package Drawing Packaging Material Table Packaging Quantity Packaging Drawing...17

4 1. General Specifications Date : 2010/09/15 Page : 1/22 No. Item Specification Remark 1 LCD size 4.3 inch(diagonal) 2 Driver element a-si TFT active matrix 3 Resolution (RGB) Display mode Normally White, Transmissive 5 Dot pitch 0.066(W) 0.198(H) mm 6 Active area 95.04(W) (H) mm 7 Module size 105.5(W) 67.2(H) 2.9(D) mm Note 1 8 Surface treatment Anti-Glare 9 Color arrangement RGB-stripe 10 Interface Digital 11 Backlight Power consumption W(Typ.) 12 Panel Power consumption W (Typ.) 13 Weight 45g (Typ.) Note 1: Refer to Mechanical Drawing.

5 2. Pin Assignment Date : 2010/09/15 Page : 2/ TFT LCD Panel Driving Section FPC Connector is used for the module electronics interface. The recommended model is FH19SC-40S-0.5SH manufactured by HIROSE. Pin No. Symbol I/O Function Remark 1 V LED- P Power for LED backlight cathode 2 V LED+ P Power for LED backlight anode 3 GND P Power ground 4 V DD P Power voltage 5 R0 I Red data (LSB) 6 R1 I Red data 7 R2 I Red data 8 R3 I Red data 9 R4 I Red data 10 R5 I Red data 11 R6 I Red data 12 R7 I Red data (MSB) 13 G0 I Green data (LSB) 14 G1 I Green data 15 G2 I Green data 16 G3 I Green data 17 G4 I Green data 18 G5 I Green data 19 G6 I Green data 20 G7 I Green data (MSB)

6 21 B0 I Blue data (LSB) Date : 2010/09/15 Page : 3/22 22 B1 I Blue data 23 B2 I Blue data 24 B3 I Blue data 25 B4 I Blue data 26 B5 I Blue data 27 B6 I Blue data 28 B7 I Blue data (MSB) 29 GND P Power ground 30 CLK I Pixel clock 31 DISP I Display on/off 32 NC - No connection 33 NC - No connection 34 DE I Data Enable 35 NC - No connection 36 GND P Power ground 37 NC - No connection 38 NC - No connection 39 NC - No connection 40 NC - No connection I: input, O: output, P: Power

7 3. Operation Specifications 3.1. Absolute Maximum Ratings (Note 1) Date : 2010/09/15 Page : 4/22 Item Symbol Min. Values Max. Unit Remark Power voltage V DD V Input signal voltage Logic input V Operation temperature T OP Note 3, 4 Storage temperature T ST Note 3, 4 LED Reverse Voltage VR V Each LED Note 2 LED Forward Current IF - 25 ma Each LED Note 1: The absolute maximum rating values of this product are not allowed to be exceeded at any times. A module should be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme condition, the module may be permanently destroyed. Note 2: VR Conditions: Zener Diode 20mA Note 3: 90% RH Max. (Max wet temp. is 60 ) Maximum wet-bulb temperature is at 60 or less. And No condensation (no drops of dew) +60, 90%RH ( ) Note 4: In case of temperature below 0,the response time of liquid crystal (LC) becomes slower and the color of panel darker than normal one.

8 3.2. Typical operation conditions Date : 2010/09/15 Page : 5/22 Item Symbol Values Min. Typ. Max. Unit Remark Power voltage V DD V Current for Driver IV DD ma V DD = 3.3V Input logic high voltage V IH 0.8V DD - V DD V Input logic low voltage V IL GND - 0.2V DD V Note1: CLK, DE, R0~ R7, G0~ G7, B0~ B7. Note Backlight Driving Conditions Item Symbol Values Min. Typ. Max. Unit Remark Voltage for LED Backlight V L V Note 2 Current for LED Backlight I L ma LED life time - 20, Hr Note 1 Note 1: The LED life time is defined as the module brightness decrease to 50% original brightness that the ambient temperature is 25 and I L =20mA. The LED lifetime could be decreased if operating I L is lager than 20 ma. Note 2: The LED Supply Voltage is defined by the number of LED at Ta=25 and I L =20mA.

9 3.4. Power Sequence Date : 2010/09/15 Page : 6/22 To prevent a latch-up or DC operation of the LCD module, the power on/off sequence should be as the diagram below. Symbol Specification Symbol Specification T1 0 T1 10 msec T4 160 msec T4 T2 0 T2 100 msec T5 160 msec T5 T3 0 T3 200 msec T6 1 msec T6

10 3.5. Timing Characteristics Timing Conditions Parallel DE mode RGB input timing table Parameter Symbol Date : 2010/09/15 Page : 7/22 Value Min. Typ. Max. Unit CLK frequency fclk MHz DEV period time Tv H DEV display area Tvd 272 H DEV blanking Tvb H DEH period time Th CLK DEH display area Thd 480 CLK DEH blanking Thb CLK CLK cycle time Tclk ns Clock width of high level Tcwh % Clock width of low level Tcwl % Clock rising time trck - 9 ns Clock falling time tfck - 9 ns Data Setup Time tdesu ns Data Hold Time tdahd ns DE Setup Time tdesu ns DE Hold Time tdehd ns

11 Timing Diagram Date : 2010/09/15 Page : 8/22

12 4. Optical Specifications Date : 2010/09/15 Page : 9/22 Item Symbol Condition Values Unit Remark Min. Typ. Max. θ L Φ=180 (9 o clock) Viewing angle (CR 10) θ R Φ=0 (3 o clock) θ T Φ=90 (12 o clock) degree Note 1 θ B Φ=270 (6 o clock) Response time T ON msec Note 3 T OFF msec Note 3 Contrast ratio CR Note 4 Color chromaticity W X Normal θ=φ= W Y Note 2 Note 5 Note 6 Luminance L cd/m² Note 6 Luminance uniformity Y U % Note 7 Test Conditions: 1. V DD =3.3V, I L =20mA (Backlight current), the ambient temperature is The test systems refer to Note 2.

13 Note 1: Definition of viewing angle range Normal line θ=φ=0 Date : 2010/09/15 Page : 10/22 θ L θ B θ R θ T Φ=90 12 o clock direction Φ=180 Active Area Φ=0 Φ=270 6 o clock direction Fig. 4-1 Definition of viewing angle Note 2: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/Field of view: 1 /Height: 500mm.) Photo detector Normal line θ=φ=0 500mm Φ=90 12 o clock direction Φ=180 Φ=0 Active Area Φ=270 6 o clock direction Fig. 4-2 Optical measurement system setup

14 Date : 2010/09/15 Page : 11/22 Note 3: Definition of Response time The response time is defined as the LCD optical switching time interval between White state and Black state. Rise time (T ON ) is the time between photo detector output intensity changed from 90% to 10%. And fall time (T OFF ) is the time between photo detector output intensity changed from 10% to 90%. White (TFT OFF) Black (TFT ON) White (TFT OFF) Photo detector output (Relative value) 100% 90% 10% 0% T ON T OFF Fig. 4-3 Definition of response time Note 4: Definition of contrast ratio Contrast ratio (CR) = Luminance measured when LCD on the " White" state Luminance measured when LCD on the "Black" state Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel. The LED driving condition is I L =20mA.

15 Date : 2010/09/15 Page : 12/22 Note 7: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each measuring area. Bmin Luminance Uniformity (Yu) = Bmax L Active area length W----- Active area width W W/3 W/3 W/6 L/6 L/3 L L/3 Fig. 4-4 Definition of measuring points B max : The measured maximum luminance of all measurement position. B min : The measured minimum luminance of all measurement position.

16 5. Reliability Test Items Date : 2010/09/15 Page : 13/22 (Note3) Item Test Conditions Remark High Temperature Storage Ta = hrs Note 1,Note 4 Low Temperature Storage Ta = hrs Note 1,Note 4 High Temperature Operation Ts = hrs Note 2,Note 4 Low Temperature Operation Ta = hrs Note 1,Note 4 Operate at High Temperature and Humidity +60, 90%RH 240 hrs Note 5 Thermal Shock Vibration Test Mechanical Shock Package Vibration Test Package Drop Test -30 /30 min ~ +80 /30 min for a total 100 cycles, Start with cold temperature and end with high temperature Frequency range:10~55hz Stroke:1.5mm Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X. Y. Z. (6 hours for total) 100G 6ms,±X, ±Y, ±Z 3 times for each direction Random Vibration : 0.015G*G/Hz from 5-200HZ, -6dB/Octave from HZ 2 hours for each direction of X. Y. Z. (6 hours for total) Height:60 cm 1 corner, 3 edges, 6 surfaces Note 4 ± 2KV, Human Body Mode, Electro Static Discharge 100pF/1500Ω Note 1: Ta is the ambient temperature of samples. Note 2: Ts is the temperature of panel s surface. Note 3: In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guarantees operation, but doesn t guarantee all the cosmetic specification. Note 4: Before cosmetic and function tests, the product must have enough recovery time, at least 2 hours at room temperature.

17 6. General Precautions 7.1. Safety Date : 2010/09/15 Page : 14/22 Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your skin or clothes, wash it off immediately by using soap and water Handling 1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or to excessive force on its surface. 2. The polarizer attached to the display is easily damaged. Please handle it carefully to avoid scratch or other damages. 3. To avoid contamination on the display surface, do not touch the module surface with bare hands. 4. Keep a space so that the LCD panels do not touch other components. 5. Put cover board such as acrylic board on the surface of LCD panel to protect panel from damages. 6. Transparent electrodes may be disconnected if you use the LCD panel under environmental conditions where the condensation of dew occurs. 7. Do not leave module in direct sunlight to avoid malfunction of the ICs Static Electricity 1. Be sure to ground module before turning on power or operating module. 2. Do not apply voltage which exceeds the absolute maximum rating value Storage 1. Store the module in a dark room where must keep at 25±10 and 65%RH or less. 2. Do not store the module in surroundings containing organic solvent or corrosive gas. 3. Store the module in an anti-electrostatic container or bag Cleaning 1. Do not wipe the polarizer with dry cloth. It might cause scratch. 2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals might permanent damage to the polarizer.

18 7. Mechanical Drawing Date : 2010/09/15 Page : 15/22

19 9. Package Drawing Date : 2010/09/15 Page : 16/ Packaging Material Table No. 1 Item LCM Module 2 Partition Corrugated Bar Dust-Proof Bag Corrugated Board-1 Corrugated Board-2 Model (Material) Dimensions (mm) Unit Weight (kg) Quantity (pcs) AT043TN25 V BC Corrugated paper BC Corrugated paper PE BC Corrugated Paper BC Corrugated Paper Remark 7 A/S Bag PE Carton Corrugated paper Total weight ± 5%KG 9.2. Packaging Quantity (1) LCM quantity per Partition: 2Rows x 40quantity per Row = 80 pcs (2) Total LCM quantity in Carton: 2 layer x 80 pcs per Partition = 160 pcs

20 9.3. Packaging Drawing Date : 2010/09/15 Page : 17/22

INNOLUX DISPLAY CORPORATION LCD MODULE SPECIFICATION

INNOLUX DISPLAY CORPORATION LCD MODULE SPECIFICATION DISPLAY CORPORATION LCD MODULE SPECIFICATION Customer: Model Name: AT056TN52 Date: 2006/12/18 Version: 01 Preliminary Specification Final Specification For Customer s Acceptance Approved by Comment InnoLux