AMP DISPLAY INC. SPECIFICATIONS. 4.3-in COLOR TFT MODULE AM480272QTZQW-T00H

Size: px

Start display at page:

Download "AMP DISPLAY INC. SPECIFICATIONS. 4.3-in COLOR TFT MODULE AM480272QTZQW-T00H"

Ralf King
6 years ago
Views:

1 AMP DISPLAY INC. SPECIFICATIONS CUSTOMER: CUSTOMER PART NO. AMP DISPLAY PART NO. APPROVED BY: 4.3-in COLOR TFT MODULE AM480272QTZQW-T00H DATE: APPROVED FOR SPECIFICATIONS APPROVED FOR SPECIFICATION AND PROTOTYPES AMP DISPLAY INC 9856 SIXTH STREET RANCHO CUCAMONGA CA TEL: FAX:

2 RECORD OF REVISION Revision Date Page Contents Editor 2011/09/26 -- New Release Rober Date : 2011/09/26 2

3 1. INTRODUCTION This is a color active matrix TFT-LCD that uses amorphous silicon TFT as a switching device. This model is composed of a 4.3inch TFT-LCD panel, a driving circuit,led backlight system and touch panel. This TFT-LCD has a high resolution (480(R.G.B) X 272) and can display up to 262,144 colors Features (1) Construction : a-si TFT-LCD with driving system, White LED Backlight. (2) LCD type :Normally Black,VA (3) Number of the Colors : 262,144 colors (R,G,B 6 bit digital each) (4) RGB Interface 40 pin. (5) LCD Power Supply Voltage : 3.3V single power input, 2. PHYSICAL SPECIFICATIONS Item Specifications unit Display resolution(dot) 480RGB (W) x 272(H) dots Display area (W) x (H) mm Pixel pitch (W) x (H) mm Color configuration R.G.B Vertical stripe Overall dimension 68.2 (W) x (H) 6.71(T) mm Surface treatment Antiglare, Hard-Coating(3H) Brightness 400 cd/m 2 Contrast ratio 500 : 1 Backlight unit LED Display color 262,144 colors Display Mode Normally Black Date : 2011/09/26 3

3. ABSOLUTE MAXIMUM RATINGS ITEM SYMBOL MIN MAX UNIT NOTE Power Supply Voltage Vcc -0.5 5 V Led Supply Voltage VLED -- 6 V Signal Input Voltage DCLK, DE R0~R5 G0~G5 B0~B5-0.5 Vcc + 0.

4 3. ABSOLUTE MAXIMUM RATINGS ITEM SYMBOL MIN MAX UNIT NOTE Power Supply Voltage Vcc V Led Supply Voltage VLED -- 6 V Signal Input Voltage DCLK, DE R0~R5 G0~G5 B0~B5-0.5 Vcc V Operation Temperature Top (1) Storage Temperature Tstg (1) 4. ELECTRICAL CHARACTERISTICS 4-1 TFT LCD Module voltage ITEM SYMBOL MIN TYP MAX UNIT NOTE Power Voltage For LCD V CC V (1) Power Voltage For VLED V DD V Logic Input Voltage ADJ Input Voltage VIH V CC * V CC V VIL 0 -- V CC *0.3 V VIH V VIL GND V 4-2 TFT LCD current consumption ITEM SYMBOL MIN TYP MAX UNIT NOTE LCD Power Current Icc ma (1) LED Power Current I LED (VLED=5V) ma (2) NOTE : (1) Typ : under 64 gray pattern Max : under white pattern (a) 64 Gray Pattern (b) White Pattern (2) Typ : When V LED is 5.0V Max : When V LED is 4.5V Note: The data is reference only Date : 2011/09/26 4

-- 4-3 Backlight Driving Conditions Paramenter Symbol Min. Typ. Max. Unit Condiction LED voltage VBAK B 23.

5 Backlight Driving Conditions Paramenter Symbol Min. Typ. Max. Unit Condiction LED voltage VBAK B V IBLEDB =20mA,Ta=25 LED forward current IBLEDB ma Ta=25 IBLEDB ma Ta=60 Note 1 : The LED Supply Voltage is defined by the number of LED at Ta=25 and IL=74mA. Note 2 : The LED life time is defined as the module brightness decrease to 50% original brightness at Ta=25 and IL=74mA. The LED lifetime could be decreased if operating IL is larger than 74mA. Note 3 : When LCM is operated over 40 ambient temperature, the ILED should be follow : Date : 2011/09/26 5

6 5. INTERFACE Pin No Symbol Function 1 U/D Up or Down Display Control 2 (NC) No connection 3 Hsync(NC) Horizontal SYNC. (Sync mode used) 4 VLED Power Supply for LED 5 VLED Power Supply for LED 6 VLED Power Supply for LED 7 Vcc Power Supply for LCD 8 Vsync(NC) Vertical SYNC. (Sync mode used) 9 DE Data Enable 10 SK/X1 Touch Panel Right Signal in X Axis 11 TPCS/Y2 Touch Panel Top Signal in Y Axis 12 ADJ Adjust for LED Brightness 13 B5 Blue Data 5 (MSB) 14 B4 Blue Data 4 15 B3 Blue Data 3 16 Vss Power Ground 17 B2 Blue Data 2 18 B1 Blue Data 1 19 B0 Blue Data 0 (LSB) 20 Vss Power Ground 21 G5 Green Data 5 (MSB) 22 G4 Green Data 4 23 G3 Green Data 3 24 Vss Power Ground 25 G2 Green Data 2 26 G1 Green Data 1 27 G0 Green Data 0 (LSB) 28 Vss Power Ground 29 R5 Red Data 5 (MSB) 30 R4 Red Data 4 31 R3 Red Data 3 32 INT IRQ Terminal. 33 R2 Red Data 2 34 R1 Red Data 1 35 R0 Red Data 0 (LSB) 36 DO/X2 Touch Panel Left Signal in X Axis 37 DI/Y1 Touch Panel Bottom Signal in Y Axis 38 DCLK Clock Signals 39 Vss Power Ground 40 L/R Left or Right Display Control Date : 2011/09/26 6

7 NOTE : 1. ADJ adjust brightness to control Pin, Pulse duty the bigger the brighter. 2. ADJ signal = 0 ~ 5.0V, operation frequency : 300Hz~1KHz 3. VSS Pin must ground contact, can not be floating. Note: The data is reference only Date : 2011/09/26 7

8 6. Touch Screen Panel Specifications 6.1. Electronic characteristics Item Min. Typ. Max. Unit Note Terminal Ω X(Film side) Resistance Ω Y(Glass side) Insulation resistance 20 MΩ DC25V Linearity 1.5 % Rated Voltage 7 V DC Transparency 80 % Non-glare Note: Do not operate it with a thing except a polyacetal pen(tip R0.8mm or less) or a finger especially those with hard or sharp tips such as a ball point pen or a mechanical pencil Mechanical & Reliability Characteristics Item Min. Typ. Max. Unit Note Activation force 250 G (1) Durability-surface Write scratching 100,000 Characters (2) Durability-surface pitting 1,000,000 Touches (3) Surface hardness 3 H JIS K5600 Note: 1.Stylus pen Input:R0.8mm polyacetal pen or Finger 2.Measurement for Surface area -1,000,000 times or over -Writing with R0.8mm plastic stylus pen; writing force 250g in active area. -Speed is 60mm/sec 3.1,000,000,tines or over(no damage on film surface) 6.3. Interface No. Symbol Function 1 XR Touch Panel Right Signal in X Axis 2 YD Touch Panel Bottom Signal in Y Axis 3 XL Touch Panel Left Signal in X Axis 4 YU Touch Panel Top Signal in Y Axis Date : 2011/09/26 8

9 7. BLOCK DIAGRAM Touch panel YU YD XL XR Date : 2011/09/26 9

10 8. INPUT SIGNAL : 8-1 Timing Specification. 8-2 Timing chart Date : 2011/09/26 10

11 Date : 2011/09/26 11

12 8-3 Color Data Assignment COLOR BASIC COLOR RED GREEN BLUE Input Data R DATA G DATA B DATA R0 G5 G0 LSB MSB G4 G3 G2 G1 LSB R5 MSB R4 R3 R2 R1 B5 MSB B4 B3 B2 B1 BLACK RED(63) GREEN(63) BLUE(63) CYAN MAGENTA YELLOW WHITE RED(0) RED(1) RED(2) RED(62) RED(63) GREEN (0) GREEN (1) GREEN (2) GREEN (62) GREEN (63) BLUE (0) BLUE (1) BLUE (2) BLUE (62) BLUE (63) B0 LSB NOTE : (1) Definition of Gray Scale, Color(n) : n is series of Gray Scale The more n value is the bright Gray Scale (2) Data : 1-High, 0-Low Date : 2011/09/26 12

13 9. OPTICAL CHARACTERISTICS Item Symbol Condition Min. Typ. Max. Unit Note Contrast ratio CR (1)(2)(3) Luminance Lw cd/m 2 (1)(3) Point - 5 Luminance Uniformity ΔL Θ=Φ= % (1)(3) Response Time ( White Black ) T r +T f ms (1)(3)(5) Viewing Horizontal Θh CR>10 Angle Vertical Θv Rx Red Ry Gx Green Color Gy Point chromaticity Bx Θ=Φ= Blue By Wx White Wy Deg. (1)(2)(4) -- (1)(3) NOTE : (1) Measure conditions : 25 ±2, 60±10%RH under 10Lux, in the dark room by BM-7TOPCON),viewing 2, VCC=3.3V, VDD=3.3V (2) Definition of Contrast Ratio : Contrast Ratio (CR) = (White) Luminance of ON (Black) Luminance of OFF (3) Definition of Luminance : Definition of Luminance Uniformity Measure white luminance on the point 5 as figure9-1 Measure white luminance on the point 1 ~ 9 as figure9-1 ΔL = [ L(MIN) / L(MAX)] X 100% Date : 2011/09/26 13

14 (4) Definition of Viewing Angle(Θ,Φ), refer to Fig9-2 as below : (5) Definition of Response Time.(White Black) Date : 2011/09/26 14

VISUAL DEFECT 10 INCOMING INSPECTION STANDARD FOR TFT-LCD PANEL DEFECT TYPE LIMIT Note INTERNAL SPOT FIBER POLARIZER BUBBLE Mura BRIGHT DOT φ<0.15mm Ignore 0.15mm φ 0.5mm N 4 0.5mm<φ N=0 0.03mm<W 0.

15 VISUAL DEFECT 10 INCOMING INSPECTION STANDARD FOR TFT-LCD PANEL DEFECT TYPE LIMIT Note INTERNAL SPOT FIBER POLARIZER BUBBLE Mura BRIGHT DOT φ<0.15mm Ignore 0.15mm φ 0.5mm N 4 0.5mm<φ N=0 0.03mm<W 0.1mm, L 5mm N 3 1.0mm<W, 1.5mm<L N=0 φ<0.15mm Ignore 0.15mm φ 0.5mm N 2 0.5mm<φ N=0 It OK if mura is slight visible through 6%ND filter A Grade B Grade Note1 Note1 Note1 C Area O Area Total C Area O Area Total Note3 N 0 N 2 N 2 N 2 N 3 N 5 Note2 DARK DOT N 2 N 3 N 3 N 3 N 5 N 8 ELECTRICAL DEFECT TOTAL DOT N 4 N 5 N 6 N 8 TWO ADJACENT DOT N 0 N 1 pair THREE OR MORE ADJACENT DOT N 1 pair N 1 pair NOT ALLOWED N 1 pair N 1 pair Note2 Note4 LINE DEFECT NOT ALLOWED (1) One pixel consists of 3 sub-pixels, including R,G, and B dot.(sub-pixel = Dot) (2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter [Note1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter Date : 2011/09/26 15

16 [Note2] Bright dot is defined through 6% transmission ND Filter as following. [Note3] C Area: Center of display area C Area: Outer of display area [Note4] Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status) adjacent defect dots, including bright and dart adjacent dot. And they will be counted 2 defect dots in total quantity. (1) The defects that are not defined above and considered to be problem shall be reviewed and discussed by both parties. (2) Defects on the Black Matrix, out of Display area, are not considered as a defect or counted. Date : 2011/09/26 16

17 11. RELIABILITY TEST CONDITIONS ITEM CONDITIONS HIGH TEMPERATURE OPERATION 70, 240Hrs HIGH TEMPERATURE AND HIGH HUMIDITY OPERATION 60, 90%RH, 240Hrs HIGH TEMPERATURE STORAGE 80, 240Hrs LOW TEMPERATURE OPERATION -20, 240Hrs LOW TEMPERATURE STORAGE -30, 240Hrs THERMAL SHOCK -20 ( 0.5Hr) ~70 ( 0.5Hr) 200Cycle 11.1 OTHERS AMIPRE will provide one year warranty for all products and three months warrantee for all repairing products. Date : 2011/09/26 17

18 12. OUTLINE DIMENSION Date : 2011/09/26 18

AMP DISPLAY INC. SPECIFICATIONS. 4.3-in COLOR TFT MODULE AM480272QTZQW-00H

AMP DISPLAY INC. SPECIFICATIONS CUSTOMER: CUSTOMER PART NO. AMP DISPLAY PART NO. APPROVED BY: 4.3-in COLOR TFT MODULE AM480272QTZQW-00H DATE: APPROVED FOR SPECIFICATIONS APPROVED FOR SPECIFICATION AND