Induced seismicity during the construction of the Gotthard Base Tunnel, Switzerland: hypocenter locations and source dimensions

Transcription

1 J Seismol (213) 17:63 81 DOI 1.17/s ORIGINAL ARTICLE Induced seismicity during the construction of the Gotthard Base Tunnel, Switzerland: hypocenter locations and source dimensions Stephan Husen & Edi Kissling & Angela von Deschwanden Received: 28 June 211 /Accepted: 28 November 211 /Published online: 21 June 212 # Springer Science+Business Media B.V. 212 Abstract A series of 112 earthquakes was recorded between October 25 and August 27 during the excavation of the MFS Faido, the southernmost access point of the new Gotthard Base Tunnel. Earthquakes were recorded at a dense network of 11 stations, including 2 stations in the tunnel. Local magnitudes computed from Wood Anderson-filtered horizontal component seismograms ranged from 1. to 2.4; the largest earthquake was strongly felt at the surface and caused considerable damage in the tunnel. Hypocenter locations obtained routinely using a regional 3- D P-wave velocity model and a constant Vp/Vs ratio An earlier version of this article was published in Volume 16, Issue 2, under DOI 1.17/s S. Husen (*) Swiss Seismological Service, ETH Zurich, Sonneggstrasse 5, CH 892 Zurich, Switzerland husen@sed.ethz.ch E. Kissling Institute of Geophysics, ETH Zurich, Sonneggstrasse 5, CH 892 Zurich, Switzerland A. von Deschwanden Institute of Geophysics, ETH Zurich, Sonneggstrasse 5, CH 892 Zurich, Switzerland Present Address: A. von Deschwanden Norwegian Polar Institute, Polar Environmental Centre, Tromsø 9296, Norway 1.71 were about 2 km below the tunnel. The use of seismic velocities calibrated from a shot in the tunnel revealed that routinely obtained hypocenter locations were systematically biased to greater depth and are now relocated to be on the tunnel level. Relocation of the shot using these calibrated velocities yields a location accuracy of 25 m in longitude, 7 m in latitude, and 25 m in focal depth. Double-difference relative relocations of two clusters with highly similar waveforms showed a NW SE striking trend that is consistent with the strike of mapped faults in the MFS Faido. Source dimensions computed using the quasidynamic model of Madariaga (Bull Seismo Soc Am 66(3): , 1976) range from 5 to 17 m. Overlapping source dimensions for earthquakes within the two main clusters suggests that the same fault patch was ruptured repeatedly. The observed seismicity was likely caused by stress redistribution due to the excavation work in the MFS Faido. Keywords Induced seismicity. Earthquake locations. Source dimensions. Gotthard Base Tunnel. Stress redistribution 1 Introduction With a length of 57 km, the Gotthard Base Tunnel forms the centerpiece of the New Alpine Traverse through the Swiss Alps. The northern entry point is at the village Erstfeld, at the southern tip of Lake Lucerne; it ends at the village Biasca in the Ticino

2 64 J Seismol (213) 17:63 81 (Fig. 1). The Gotthard Base Tunnel is designed as a railway tunnel for passenger and freight trains, consisting of two single tracks, each with a diameter of 9.2 m. Three intermediate access points divide the tunnel into five sections with about equal length. The southernmost of these access points, called MFS Faido, is located near the village of Faido in the Ticino (Fig. 1). It is designed to serve as an emergency access point to evacuate train passengers in case of emergencies. Therefore, the layout of the MFS Faido consists of several parallel and crossing tubes (Fig. 2). Excavation was done by drilling and blasting, starting in February 22; main excavation work of the MFS Faido was finished by October 26. The Gotthard Base Tunnel crosses the central Alps. It is located mainly in igneous rocks consisting of the Aare and Gotthard massifs in the north and in metamorphic rocks of the Penninic nappes in the south. Geology in the MFS Faido is dominated by the contact between the Lucomagno and Leventina gneisses, which are part of the Penninic nappes. The contact zone forms a complex three-dimensional structure (Fig. 2). In terms of rheology, these two gneisses behave differently: At the depth of the tunnel, the Lucomagno gneiss deforms more ductile, whereas the Leventina gneiss deforms more brittle. During excavation, a complex fault zone was encountered in the northern part of the MFS Faido (Fig. 2). The fault zone strikes about NW SE with a dip of about 8. Rocks of the fault zone are heavily fractured, including kakitrite in the fault kernel. Excavation of the MFS Faido was accompanied by large deformation and extensive and strong rock burst activity. The majority (75%) of rock bursts occurred close to the active rockface, within 3 h after blasting (Hagedorn and Stadelmann 21). Large rock bursts also occurred repeatedly in sections, where excavation work was already finished. These sections located in the northern part of the MFS Faido, in the complex contact zone of the Lucomagno and Leventina gneisses (Fig. 2). Rock bursts were sometimes accompanied with spalling of shotcrete, threatening workpeople in the tunnel. Between March 24 and October 25, the Swiss Seismological Service Fig. 1 Map of study area. Gray circles mark seismicity as recorded by the Swiss Digital Network (SDSNet) between 1995 and 25; red circles mark earthquakes in the vicinity of the village Faido between 24 and 25. Size of the circles scales with magnitude. Permanently installed stations of the SDSNet are shown by black triangles. Green dashed line marks location of the Gotthard Base Tunnel. Inset in upper right corner shows location of the study region within Switzerland BNALP Erstfeld MUO Gotthard basetunnel Sedrun Stations SDSNet Earthquakes Ml=2. Ml=1. 5 km FUSIO Faido Biasca

3 J Seismol (213) 17: Fig. 2 Geologic map of the multifunction station MFS Faido. Lucomagno and Leventina gneisses are shown by light and dark gray colors, respectively. White lines mark mapped faults in the MFS Faido (Hagedorn and Stadelmann 21). Black lines denote tunnel layout of the MFS Faido N 75 Lucomagno gneiss Leventina gneiss Faults (mapped) 76 5 m recorded 12 small earthquakes (ML.9 1.6) in the vicinity of the village of Faido (Fig. 1). Prior to March 24, no earthquakes were recorded in this area (Baer et al. 25). Hypocenter locations of these earthquakes were poorly constrained due to the low number of stations of the Swiss Digital Seismic Network (SDSNet) that recorded the events. Only station FUSIO of the SDSNet was within 1 km distance of the epicenters of the events (Fig. 1). Three of the recorded earthquakes could be correlated with the occurrence of large rock bursts in the tunnel, suggesting that the observed seismicity was related to the construction of the MFS Faido. In order to monitor ongoing seismicity in the vicinity of the MFS Faido and to study possible mechanisms that caused the observed earthquake activity, a dense seismic network of 1 stations was installed and operated by the Swiss Seismological Service in the region of Faido. The work was done under a contract given by the AlpTransit Gotthard AG, the owner of Gotthard Base Tunnel. In this study, we will describe the installation and operation of the AlpTransit seismic network, present our results in terms of hypocenter locations and source dimensions, and discuss possible mechanisms that caused the observed seismicity. 1.1 AlpTransit network In order to monitor the seismicity in the vicinity of the MFS Faido, a dense network of seismic stations was installed between October 25 and December 25, with the exception of station MFSFB, which was installed in November 26 (Fig. 3). The AlpTransit network was operated between October 25 and April 21 by the Swiss Seismological Service (SED) at ETH Zurich, under a contract with AlpTransit Gotthard AG. The design of the network consisted of an inner circle with a diameter of 1 2 km (stations CHAT1, CHAT2, and TONGO) and an outer circle with a diameter of 1 12 km (stations CHIR2, DOETR, FUSIO, LUKA1, NARA, RITOM) centered on the MFS Faido. In addition, two stations (MFSFA and MFSFB) were installed within the MFS Faido (Fig. 3). The majority of stations were equipped with short-period seismometers (Lennartz LE-3-D 1 s), except for stations FUSIO, MFSFA, and MFSFB. Station FUSIO belongs to the SDSNet, a permanently operated network by SED, and is, therefore, equipped with broadband seismometer (Streckeisen STS). Due to the expected high-noise level in the tunnel and due to the small epicentral distances, stations MFSFA and MFSFB were equipped with 24-bit accelerometers (Kinemetrics EpiSensor). Data were recorded continuously at sampling frequencies of 12 Hz (FUSIO), 2 Hz (CHAT1, CHAT2, CHIR2, DOETR, FUSIO, LUKA1, NARA, RITOM, TONGO), and 25 Hz (MFSFA and MFSFB). Except for station LUKA1, all data were streamed in real time to the SED data center in Zurich using high-speed internet connections. Data from station LUKA1 were manually downloaded and merged to existing data since the bandwidth of the internet connection at station LUKA1 was not sufficient to allow for real-time data streaming. All stations were synchronized using GPS timing. Unfortunately, a software bug caused timing problems at stations CHIR1, DOETR, NARA, RITOM, and TONGO between October and November 25. Consequently, arrival times

4 66 J Seismol (213) 17:63 81 Fig. 3 Map of the AlpTransit seismic network. Different sensor types are marked by different symbols as indicated. Station FUSIO belongs to the Swiss Digital Seismic Network. White line marks location of the Gotthard Base Tunnel 8 4 E LUKA1 9 E Lennartz LE-3D 1s Kinemetrics Episensor Streckeisen STS RITOM DOETR 46 3 N CHAT1 MFSFB CHAT2 MFSFA FUSIO TONGO NARA CHIR2 picked at these stations between October and November 25 were not used for earthquake location; amplitudes were still used to compute local magnitudes. 2 Routine data analysis 2.1 Hypocenter locations and local magnitudes Event detection was based on short-time/long-time (STA/LTA) amplitude ratios computed continuously on the incoming data streams of the AlpTransit stations. An event was declared if the STA/LTA amplitude ratio exceeded a given threshold at two or more stations within time window of 4 s. For each event, waveform data of 9 s length from stations of the AlpTransit network and nearby broadband stations of the SDSNet were extracted from the continuous data streams. Each event file was manually checked and false events were removed. This resulted in 112 earthquakes detected by the AlpTransit network between October 25 and August 27. Arrival times of P- and S-waves were picked manually by experienced seismologists at the SED. All data were band-passed filtered in the frequency band 1 3 Hz to ensure a uniform signal character as much as possible. Moreover, band-passed filtering suppressed acausal finite impulsive response filter artifacts which were sometimes present at nearby stations (CHAT1, CHAT2, MFSFA, and MFSFB) due to very impulsive arrivals of the direct P-wave (Scherbaum and Bouin 1997). Uncertainties in arrival times were assigned using a quality weighting scheme with uncertainties ranging from.5 s (quality ) to.4 s (quality 3) (Table 1). The majority of P-wave arrival times were of quality due to high signal-tonoise ratios and a high-frequency content of the phase arrivals (Table 3). Earthquakes were routinely located using a regional 3-D P-wave velocity derived from local earthquake tomography and controlled-source seismology data (Husen et al. 23) and the NonLinLoc software package (Lomax et al. 2). A constant Vp/Vs ratio Table 1 Uncertainty assessment for arrival time picking Class Uncertainty Number of P-wave picks ±.25 s ±.5 s ±.1 s ±.2 s 3 5 Number of S-wave picks

5 J Seismol (213) 17: of 1.71 was used for S-wave arrivals. NonLinLoc computes the posterior probability density function (pdf) of the earthquake location problem (Tarantola and Valette 1982) using an importance sampling algorithm, called OctTree search (Lomax and Curtis 21). The solution includes uncertainties due to the geometry of the network, measurements errors of the observed arrival times and errors in the calculation of theoretical travel times. These uncertainties are represented either as density scatter plots (Lomax et al. 2) or as traditional 68% confidence ellipsoids. In the case of well-constrained hypocenter locations, the 68% confidence ellipsoid is a valid approximation of the posterior pdf (Lomax et al. 2). Figure 4 shows hypocenter locations for earthquakes with an azimuthal gap less than 16 and with a length of the major axis of the 68% confidence ellipsoid less than 3 km. Y(km) Z (km) X(km) CHAT1 MFSFB TONGO Faido 2. km CHAT2 MFSFA DOETR NARA Gotthard basetunnel X(km) Gotthard basetunnel 6/27 2/27 1/26 6/26 2/26 1/25 Month/Year Z(km) Magnitude Fig. 4 Hypocenter locations of earthquakes in the vicinity of the MFS Faido between October 25 and June 27. Map view and two vertical cross-sections along X- and Y-axis are shown. Only events with GAP <16 and length of the major axis of the 68% confidence ellipsoid <3 km are shown. Earthquake locations were obtained using regional 3-D P-wave velocity model (Husen et al. 23) and a constant Vp/Vs ratio of Origin time of earthquakes is coded by color as indicated. Circle size is scaled by magnitude as indicated. Locations of stations of the AlpTransit seismic network are marked by triangles. Square marks location of the town of Faido. Black line marks location of the Gotthard Base Tunnel. Thin black lines in the vertical cross-sections mark elevation of the Gotthard basetunnel. Note that earthquakes locate on average 2 km below the Gotthard Base Tunnel Y(km) Average length of the major axis of the 68% confidence ellipsoid was 1.9 km. Local magnitudes (M L ) were computed using maximum amplitudes of the Wood Anderson-filtered horizontal component seismograms. The final magnitude for one event corresponds to the median of all station magnitudes. The distance attenuation relationship used at SED was originally derived using vertical recordings on short-period instrumentation with analogue telemetry (Kradolfer 1984). After updating to the modern SDSNet an empirically derived correction factor of.1 is applied to maintain consistency in the M L scale (Edwards et al. 21). The distance attenuation relationship used at SED is not well-calibrated for distances <3 km as many of the signals used in the calibration at that time were clipped in this distance range due to the limited dynamic range of analogue telemetry. Nevertheless, we decided to use the SED M L scale, but we did not compute magnitudes at stations MFSFA and MFSFB since their locations are generally less than 1 km from the epicenter locations of the earthquakes. Our magnitudes may, therefore, be over- or underestimated compared to the SED M L scale, but they are internally consistent as more or less the same set of stations is used for computation. A few earthquakes were too small to be recorded at stations on thesurface;theywereonlyrecordedatstationsmfsfb and MFSFA in the tunnel. Magnitudes for these events were computed using amplitude ratios of Wood Anderson-filtered and integrated horizontal component seismograms at station MFSFA for a reference M1. earthquake and each event. The magnitude of the reference event was computed using the surface stations of the network as described above. In principle, the spectral fitting method described in Section 5 would allow to compute moment magnitudes M w for small earthquakes (Edwards et al. 21). Due to quality constraints (mainly signal-to-noise ratio and azimuthal distribution of stations) moment magnitudes could only be computed for 53 out of 112 events. We, therefore, decided to use M L instead of M w in our study to have a more complete record of magnitudes over time. 2.2 Calibration shot Routinely obtained earthquake locations clustered in the vicinity of the MFS Faido but they located 2 km below the tunnel (Fig. 4). Focal depths were well constrained due to the excellent network geometry

6 68 J Seismol (213) 17:63 81 for most earthquakes as indicated by the small size of the 68% confidence ellipsoid. Large P-wave amplitudes on the horizontal components of station MFSFA, however, suggested that earthquakes likely occurred at the depth of the tunnel (i.e., 4 m above sea level). Moreover, S P arrival times at station MFSFA were less than.1 s indicating that the earthquakes located at a distance of only a few hundred meters from station MFSFA. All this suggests that hypocenter locations obtained using the regional 3-D P-wave model and a constant Vp/Vs ratio were likely biased to greater depth. In order to check the reliability of the regional 3-D P-wave velocity model and to assess location accuracy of the obtained hypocenter locations, a calibration shot was fired on November 9, 26. The shot was set off in southern part of the MFS Faido; the charge was 1 kg explosive. A Kinemetrics EpiSensor was installed at about 3 m distance to the shot point to record the origin time of the shot. The shot was well recorded at all stations of the AlpTransit network (Fig. 5). Average P-wave velocities were computed for each station using the arrival time of the direct P-phase. Overall, seismic velocities were about 2% faster than the corresponding P-wave velocities taken from the 3-D P-wave velocity model. Moreover, seismic velocities derived from the calibration shot showed large local variations between 4.7 and 5.7 km/s, which were not present in the regional 3- D P-wave velocity model (Fig. 5). We relocated the calibration shot using seismic velocities taken from the regional 3-D P-wave velocity model and derived from the shot itself (Fig. 6). For the latter, we used a smaller model error in NonLinLoc as uncertainties in seismic velocities derived from the calibration shot are much smaller than for those taken from the 3- D P-wave velocity model. As a consequence, location uncertainties (as shown by the 68% confidence ellipsoid in Fig. 6) are significant smaller. It should be noted that model uncertainty estimates as used for the calibration shot will likely not reflect all expected velocity heterogeneity. A more complete uncertainty estimate, however, could only be achieved by placing calibration shots next 1.1 Travel-time (t-x/6.) [s] CHAT1: 5. km/s (4.2 km/s) TONGO: DOETR: 5.2 km/s 5.3 km/s (4.2 km/s) (4.3 km/s) CHAT2: 4.7 km/s (4.1 km/s) LUKA: 5.2 km/s (4.3 km/s) NARA: 5.7 km/s (4.4 km/s) RITOM: 5.7 km/s (4.4 km/s) CHIR2: 5.5 km/s FUSIO: 5.7 km/s (4.5 km/s) Distance [m] Fig. 5 Travel time diagram of calibration shot. Travel times are reduced by 6 km/s. Waveforms of different stations of the AlpTransit seismic network are shown by different colors as indicated. Waveform of the station close to the calibration shot is shown in gray. Name and average P-wave velocity for each station as estimated from the slope of the corresponding travel time curves is indicated. Corresponding P-wave velocity as estimated from the regional 3-D P-wave velocity model (Husen et al. 23) is shown in brackets. P-wave velocities as estimated from the regional 3-D P-wave velocity model are on average 1 km/s slower

7 J Seismol (213) 17: X(km) Z(km) CHAT2 CHAT2 1 Y(km) -1 TONGO MFSFA -1 Y(km) -3 1 km Z(km) Z(km) 1 1 Z(km) X(km) Fig. 6 Hypocenter locations of relocated calibration shot. Blue circles and blue dashed lines mark hypocenter location computed using regional 3-D P-wave velocity model (Husen et al. 23); black circles and black lines mark hypocenter location computed using average P-wave velocities for each stations as estimated from the calibration shot. Projection of the corresponding 68% confidence ellipsoid is shown in blue and black, respectively. Smaller model uncertainties for calibrated velocities yield a smaller size of the 68% confidence ellipsoid. True location of the calibration shot is marked by green star. Location of stations of the AlpTransit seismic network is marked by squares. Using the regional 3-D P-wave velocity model, calibration shots locate 2 km deeper than the true location to the earthquake source region, which was not realistic in the scope of this study. Using calibrated seismic velocities for each individual station, the calibration shot was relocated within 25 m in X-direction, 7 m in Y- directon, and 25 m in Z-direction of the true location (Fig. 6). Using the regional 3-D P-wave velocity model, the calibration shot was relocated within 2 m in X- direction, 2 m in Y-direction, and 2,1 m in Z-direction. Hence, earthquake locations computed using the regional 3-D P-wave model were biased to greater depth due to the use of inadequate seismic velocities. Consequently, all earthquakes were relocated using calibrated seismic velocities for each individual station (Fig. 7). 2.3 Temporal and spatial evolution of observed seismicity In total, 112 earthquakes were detected and located by the network between October 25 and August 27. Figure 8 shows the temporal evolution of the seismicity. Seismic activity was highest in the months December 25, March 26, and May 26. Overall, seismicity decayed over time and no earthquake was recorded after August 27 (Fig. 8), about 5 months after the main excavation work was finished in the MFS Faido. Local magnitudes ranged between 1. and 2.4 (Fig. 8). It should be noted that negative magnitudes are only based on amplitude ratios at station MFSFA as discussed in Section 3.1. Hence, these magnitudes should be interpreted carefully. The largest earthquake with M L 2.4 occurred on March 25, 26. It was strongly felt by local people in nearby villages and caused intensive media interest. The fact that the earthquake was strongly felt at the surface is likely due to its shallow focal depth. The earthquake occurred at a depth.5 1. km below the Earth s surface. No damage was reported at the surface, but the earthquake caused considerable damage in the MFS Faido, including cracking and massive

8 7 J Seismol (213) 17:63 81 Y(km) Z (km) X(km) CHAT1 MFSFB TONGO Faido 2. km CHAT2 MFSFA DOETR NARA Gotthard basetunnel X(km) Z(km) flaking of the reinforced tunnel walls, and uplift of about.5 m of the tunnel floor. The M L 2.4 earthquake was well recorded at all stations of the AlpTransit network and of the SDSNet, up to distances of 14 km. The excellent azimuthal and spatial distribution of the observations allowed us to compute a focal mechanism based on first motions (Fig. 9). Take-off angles were computed for the regional Gotthard basetunnel 6/27 2/27 1/26 6/26 2/26 1/25 Month/Year Magnitude Fig. 7 Hypocenter locations of earthquakes in the vicinity of the MFS Faido between October 25 and June 27 (same layout as Fig. 4). Only events with GAP <16 and length of the major axis of the 68% confidence ellipsoid <3 km are shown. Earthquake locations were obtained using calibrated P-wave velocities. Note that earthquakes locate on average at the same depth as the Gotthard Base Tunnel Y(km) 3-D P-wave velocity model (Husen et al. 23) at the hypocenter location computed using only stations of the AlpTransit network and calibrated seismic velocities as discussed in the previous section. As can be inferred from Fig. 9, fault planes of the focal mechanism are well constrained by our observations. First motions observed at stations DOETR, LUKA1, and NARA seem to be inconsistent with obtained focal mechanism. These discrepancies can be due to incorrectly computed take-off angles for these stations, which were computed as upward. The shallow depth of the event (focal depth is about 1 km below the Earth s surface) and significant surface topography in the region, however, could result in downward oriented take-off angles for these stations, which would be consistent with the obtained focal mechanism. Strike and dip of one of the fault planes of the focal mechanism of the M L 2.4 earthquake is consistent with strike and dip of the mapped fault zone in the MFS Faido. We, therefore, interpret the focal mechanism of the M L 2.4 earthquake as a NW SE oriented, steeply dipping normal fault event that likely occurred on one of the faults belonging to the fault system mapped in the MFS Faido (Fig. 2). 3 High-precision earthquake relocation 3.1 Improving arrival time picks by waveform cross-correlation Routine data analysis revealed earthquakes with a high degree of waveform similarity suggesting that these Fig. 8 Temporal evolution of the observed seismicity between October 25 and December 27. Top panel shows number of events per month; bottom panel shows local magnitudes (M L ) per month. Open circles mark earthquakes for which ML could only be computed using recordings of station MFSFA. Thick gray line marks the end of the excavation work in the MFS Faido (October 26) Number Magnitude (ML) Oct Dec Feb Apr Jun Aug Oct Dez Feb Apr Jun Aug Oct Dec Month Month Oct Dec Feb Apr Jun Aug Oct Dec Feb Apr Jun Aug Oct Dec Month Month

9 J Seismol (213) 17: RITOM DOETR FUSIO CHAT2 TONGO CHAT1 events occurred very close to each other with similar source mechanisms. We, therefore, performed a cluster analysis based on waveform similarity to identify families of similar earthquakes. Following the cluster analysis, cross-correlation times within each family are then used to improve consistency of absolute arrival times. Such an approach has been shown to significantly reduce location scatter, which is often introduced by the variability in picking arrival times on an event-byevent basis (Rowe et al. 24, 22b). Details on the techniques used for waveform cross-correlation and clustering can be found in Rowe et al. (22a). The goal of the cluster analysis is to obtain families with similar waveforms in order to improve arrival times by cross-correlation. This is in contrast to other clustering techniques that aim at identifying clusters of mostly identical waveforms. For these reasons, we based our cluster analysis only on one station (DOETR) with an almost complete record of the observed seismicity and high signal-to-noise ratios. Waveforms were filtered using a 1 1 Hz bandpass filter prior to waveform LUKA1 CHIR2 NARA Fig. 9 Fault plane solution of the ML 2.4 earthquake of March 25, 26, based on first-motion polarities. Shown is equal-area, lower-hemisphere projection. Preferred rupture plane is shown by thick black line. Solid circles correspond to compressive first motion (up) and open circles to dilatational first motion (down). Observations from the stations of the AlpTransit seismic network are labeled. Mismatch between observed and computed first motion at stations RITOM, LUKA1, and NARA can be caused by erroneous take-off angle computations. See text for more details cross-correlation. A window length of 2 s, starting.4 s before the routinely determined P-wave arrival time, was chosen for cross-correlation. This window length included the arrivals of P- and S-wave energy. Finally, a cross-correlation coefficient of.9 was chosen as a cutoff for clustering. The goal of these parameter settings was to establish families with highly similar waveforms. A shorter window length including only the P-wave arrival, for example, would have yielded a larger number of waveforms with higher cross-correlation coefficients but not necessarily more reliable results as scattering effects and the arrival of the S-wave would have not be considered. The cluster analysis revealed 12 clusters, of which two clusters contained a larger number of earthquakes (clusters 11 and 12; Table 2). The M L 2.4 earthquake of March 25, 26, is associated with cluster 11, which consists of 16 earthquakes and is the largest cluster. Following the cluster analysis, arrival times of earthquakes in clusters 11 and 12 were refined using cross-correlation time lags for each station following the approach of Rowe et al. (22a). Arrival times of earthquakes in the remaining clusters were not adjusted, as the number of events per cluster was too low. Stations with a good signal-to-noise ratio (e.g., station DOETR in Fig. 1) showed only a minor improvement in pick consistency. Pick improvement was considerable for stations with a low signal-to-noise ratio (e.g., station NARA in Fig. 1), demonstrating that arrival time picks at stations with a low signal-to-noise ratio suffer from a strong variability. Following the pick adjustment, traces were stacked for each station and cluster to check for a mean bias in adjusted arrival times. Moreover, pick uncertainties were estimated for each stack following the concept of earliest and latest possible arrival times, i.e., the difference between earliest and latest possible arrival time determines absolute pick uncertainty (Diehl et al. 29). Pick uncertainties derived from the stacks were a factor of 4 5 smaller than the corresponding uncertainties derived during routine picking due to an improved signal-to-noise ratio of the stacks. Figure 11 shows hypocenter locations of earthquakes in cluster 12 as computed by NonLinLoc and using velocities as estimated from the calibration shot. The improvement in picking consistency yields a tight clustering in epicenter location and focal depth. Location uncertainties as outlined by the 68% confidence ellipsoid were also slightly reduced due to reduced picking uncertainties as estimated from the stacks

10 72 J Seismol (213) 17:63 81 Table 2 Results of cluster analysis using waveform cross-correlation Cluster Number of events Mean crosscorrelation coefficient Standard deviation of cross-correlation coefficient Minimum crosscorrelation coefficient Maximum crosscorrelation coefficient Cluster contains all earthquakes that could not be associated with any other cluster (orphans) (Fig. 11). Nevertheless, the size of the location uncertainties prevents interpretation of the internal structure of the cluster, i.e., whether all earthquakes occurred at the same location or not. 3.2 Double-difference hypocenter locations In order to improve our resolution to resolve any internal structure, we relocated earthquakes of clusters 11 and 12 using hypodd (Waldhauser and Ellsworth 2). Initial locations were computed by NonLinLoc using either original arrival time picks or refined arrival time picks. Since the original version of hypodd does not account for station elevations, we modified hypodd accordingly. Neglecting station corrections in hypodd does not pose a problem as long as focal depths are large compared to epicentral distance. For these cases, changes in the take-off angles are small if station elevations are used or not. In our study, however, where seismicity is very shallow and stations in the tunnel are nearly at the same elevation as the seismicity, the use of station elevations becomes crucial to compute correct take-off angles. We used a velocity model with a constant P-wave velocity of 5.33 km/s, which corresponds to the average velocity of all stations in the AlpTransit network as estimated by the calibration shot. Only P-wave arrival times of stations in the AlpTransit network were consequently used for relocation. Among network geometry, the power of hypodd to resolve small structures depends on uncertainties and consistencies of the arrival times. Therefore, cross-correlation measurements are often combined with catalog picks to improve hypodd locations (e.g., Waldhauser and Ellsworth 2; Richards et al. 26). This approach requires careful and sophisticated weighting between the two sets of arrival times. In this study, we used only one set of arrival times, which were either derived from routine picking (catalog picks) or from the pick refinement as outlined above. The latter set of arrival times inherently contains information from cross-correlation measurements, as they were used to refine the picks. The advantage of our approach is that no sophisticated weighting scheme is needed as only one set of arrival times is used. We stop hypocenter relocation in hypodd when the final RMS of all travel time residuals reaches our assumed average picking uncertainty (2 ms for original picks and 6 ms for refined picks). Compared to original locations obtained by NonLin- Loc, hypocenter locations show a much tighter clustering when they are relocated by hypodd (Fig. 12). Location scatter is further reduced if the refined picks are used. Location uncertainties as computed by hypodd are in the range of 3 6 m for catalog picks and 1 2 m for the refined picks, respectively. Since hypodd scales formal location uncertainties by the final traveltime residual, smaller uncertainties can be expected if the refined picks are used for relocation.

11 J Seismol (213) 17: Fig. 1 Aligned waveforms (left panel) and stack (right panel) of earthquakes in cluster 12 for station DOETR (a d) and NARA (e h). Vertical component is shown. Waveforms are aligned using routinely determined arrival times (a, e) and adjusted arrival times (c, g) based on time lags derived from cross-correlation measurements marked by solid black lines. Note the improved alignment for waveforms at station NARA if arrival times are adjusted by cross-correlation. See text for more details on how arrival times were adjusted a) original arrival time picks at DOETR b) sample c) sample adjusted arrival time picks at DOETR c) stack of c) sample sample stack of a) e) original arrival time picks at NARA f) stack of e) sample sample g) adjusted arrival time picks at NARA h) stack of g) sample sample Assessing double-difference location uncertainties using synthetic data The reliability of location uncertainties computed by hypodd needs to be checked by statistical sampling techniques, such bootstrap or jacknife tests, to assess the influence of the network geometry on the location uncertainties (Waldhauser and Ellsworth 2). In our study, we performed tests with synthetic data to assess location uncertainties. Synthetic traveltimes are computed for each observation within clusters 11 and 12 using the same velocity model used for relocation in hypodd (i.e., a constant P-wave velocity of 5.33 km/s). For each cluster, all earthquakes originate at the same location (Fig. 13). Gaussian distributed errors are added to the synthetic traveltimes to model pick uncertainties. We use standard deviations of.25 and.1 s to simulate pick uncertainties for routine picks and refined picks, respectively. Our synthetic data are, therefore, as close as possible to the observed data but using known (or true ) hypocenter locations. Figure 13 shows the results using both synthetic datasets. As expected, location scatter is smaller if picks with smaller uncertainties (standard deviations) are used. Using routine picks the two clusters, which were separated by 2 m in epicenter, cannot be

12 74 J Seismol (213) 17: x (km) z (km) x (km) z (km) m 2 m 2 m 2 m y (km).6 y (km).6.2 MFSFA.2 MFSFA.8 2 m.8 2 m z (km).4 z (km) Fig. 11 Hypocenter locations of earthquakes in cluster 12 using routinely determined P-wave arrival times (gray stars) and adjusted P-wave arrival times (red stars). For the latter, two earthquakes locate at exact the same location, for which reason only seven red stars are seen. Projection of 68% confidence ellipsoid is shown for two earthquakes (marked by small black dot). Hypocenter locations were computed using calibrated P- wave velocities shown in Fig. 5. Location of station MFSFA in the Gotthard Base Tunnel is marked by black triangle. Dashed lines mark elevation of the Gotthard Base Tunnel. Map view and two vertical cross-sections along X- and Y-axis are shown. Note that the improved clustering of hypocenter locations if adjusted P-wave arrival times are used separated. Our results also show nicely the influence of the network geometry on the location results. For both tests, one event shows a slightly larger shift in focal depth, whereas the scatter in focal depth of the remaining events is small (Fig. 13). This particular event is lacking observations of stations CHAT2 and FUSIO; all other events are observed at all 1 stations of the AlpTransit network. The poorer network geometry for this particular event is indicated by a larger uncertainty in focal depth, though. Our results demonstrate that hypodd systematically underestimates location uncertainties. Since earthquakes within each cluster share the same true location, uncertainties for these events should overlap, which they do not (Fig. 13). We estimated mean location errors by computing the mean distance between true hypocenter and relocated hypocenter locations of all earthquakes for each direction (Table 3). Location errors are largest in X-direction and smallest in Z-direction. This is in Fig. 12 Double-difference hypocenter locations of earthquakes in cluster 11 (blue and black crosses) and cluster 12 (red and gray crosses). Same layout as Fig. 11. Black and gray crosses mark hypocenter locations obtained using routinely determined P-wave arrival times; blue and red crosses mark hypocenter locations obtained using adjusted P-wave arrival times. Size of the crosses is scaled by error as computed by hypodd. Dashed lines mark elevation of the Gotthard Base Tunnel. Note that the improved clustering of hypocenter locations if adjusted P-wave arrival times are used contrast to mean location errors computed by hypodd, which are largest in Z-direction. Moreover, mean location errors computed by hypodd are significantly smaller than our estimates in X- and Y-direction but larger in Z-direction (Table 3). The ratio between our estimates and those computed by hypodd becomes smaller for the dataset with smaller errors (standard deviation.1 s). We attribute these differences to the fact that location errors computed by hypodd do not account properly for the joint effect of station geometry and pick uncertainties. This effect becomes stronger if larger pick uncertainties are present. We, therefore, use the ratio between mean location errors computed by hypodd and our estimates to scale location errors computed for real data, i.e., ratios of 2.5, 1.1, and.6 in X-, Y-, and Z-direction, respectively, for hypocenter locations relocated with the refined picks. Figure 14 shows epicenter locations of earthquakes of clusters 11 and 12. Earthquakes have been relocated using hypodd and refined picks. Relocated seismicity

13 J Seismol (213) 17: a).5 routine pick uncertainty (.25 s) MAP VIEW A.8 Cross Section: A A.8 Cross Section: B B distance [km] B B hypodd depth [km].6.4 hypodd depth [km].6.4 hypodd A distance [km] synthetic data distance [km] synthetic data.2 synthetic data distance [km] b) refined pick uncertainty (.1 s) MAP VIEW Cross Section: A A Cross Section: B B.5 A.8.8 distance [km] B B hypodd depth [km].6.4 hypodd depth [km].6.4 hypodd A distance [km] synthetic data distance [km] synthetic data.2 synthetic data distance [km] Fig. 13 Tests with synthetic data to assess location errors of double-difference hypocenter locations. Gaussian distributed errors with mean and standard deviations of a.25 and b.1 s were added to simulate picking uncertainties of routinely determined and refined arrival times picks, respectively. Map view and two vertical cross-sections along A-A and B-B are shown. Blue and red crosses mark double-difference hypocenter locations computed using synthetic travel times for clusters 11 and 12, respectively. The real set of observations for clusters 11 shows a NW SE striking structure consisting of several sub-clusters. Location uncertainties for the different sub-clusters do not overlap suggesting that they occurred at different locations. This is confirmed by a visual check of waveforms recorded at station and 12 was used to compute synthetic travel times. For each cluster, synthetic hypocenter locations were identical (marked by black crosses). Size of the crosses is scaled by error as computed by hypodd. Mean location errors as computed by hypodd and as estimated from relocated synthetic hypocenter locations (Table 3) are shown by gray crosses. Note that scatter of relocated synthetic hypocenter locations is larger than the size of the crosses, indicating that computed errors are too small. See text for more details MFSFA, located at about 4 m distance from the seismicity (Fig. 14). Waveforms of earthquakes within each sub-cluster are nearly identical with similar S P travel times. Waveforms between the different subclusters are distinctively different with varying S P Table 3 Mean location errors (m) as computed by hypodd and as estimated from tests with synthetic data X-direction Y-direction Z-direction hypodd, standard deviation.25 s synthetic data, standard deviation.25 s hypodd, standard deviation.1 s synthetic data, standard deviation.1 s Standard deviation refers to standard deviation of the Gaussian distribution used to simulate picking uncertainties. See text and Fig. 13 on details of the tests

14 76 J Seismol (213) 17:63 81 X (km) M m M M M M 2.4 Y (km) M M M M M M M 1.3 Time [s].4 MFSFA M.8.5 Time [s] Fig. 14 Double-difference epicenter locations and waveforms for earthquakes in clusters 11 (blue) and 12 (red). Epicenter locations were computed using refined arrival times based on cross-correlation measurements. Size of the crosses is scaled by error as computed by hypodd and adjusted based on tests with synthetic data (Table 3). Band-passed filtered (1 3 Hz) waveforms of vertical components are shown for station MFSFA (black triangle). Origin times and magnitudes are indicated. Note that scatter in epicenter locations is supported by differences in waveform similarity travel times (Fig. 14). The M L 2.4 earthquake of March 25, 26, forms a single sub-cluster suggesting that it occurred on a single structure or fault patch. 4 Source dimensions Assuming a circular rupture model, the source radius r is inversely proportional to the corner frequency f c (e.g., Madariaga 1976; Gibowicz et al. 199; Abercrombie 1995): r ¼ kc=f c ð1þ where c is the wave speed (α for P-wave velocity and β for S-wave velocity) and k is a proportionality factor depending on the source model and wave type. For the static S-wave source model of Brune (197) k equals.375. In the quasidynamic model of Madariaga (1976) k is dependent on the angle θ, which is the angle between the fault normal and the take-off angle of the P- and S-wave at the source. Assuming a good azimuthal coverage of f c observations around the source average k values of.31 and.21 can be used for P- and S- waves, respectively (Madariaga 1976). These average k values were computed assuming a rupture speed of.9 c. Source radii computed using the Brune model will be larger than those computed using the Madariaga model due to a larger k value. Studies in Polish mines showed that source dimensions estimated using the Madariaga model are in good agreement with independent observations (see Gibowicz et al. 199 and references therein). We, therefore, decided to use the Madariaga model to estimate source radii. We will use a k value of.21 as corner frequencies were estimated from S-wave spectra and only for earthquakes with a good azimuthal distribution of stations (see below). We use a spectral fitting method to compute corner frequency f c, the signal moment (the frequencyindependent far-field amplitude), and a pathdependent t* value (Edwards et al. 21). The approach involves a combined grid-search for f c and Powell s minimization for the signal moment and t*. Details on the method can be found in Edwards et al. (28, 21). The grid search over f c is performed at 1% intervals, starting at the equivalent f c value for a.1 MPa approximate stress drop increasing to the equivalent f c for a 1 MPa approximate stress drop. The wide search range prevents any bias in the final results. A common f c is assumed for each earthquake across all recordings. Given a good azimuthal coverage of observations, this will provide a stable average consistent with our approach to use a constant k value to relate f c to source radii. The inherent coupling of f c

15 J Seismol (213) 17: and t* requires a priori knowledge on the attenuation structure to derive meaningful f c and stress drop values (e.g., Allmann and Shearer 27; Edwards et al. 28). We compute an average Q factor by plotting t* values over hypocentral distance. For constants β and Q, this will yield a straight line with the slope inversely proportional to Q (Anderson and Hough 1984). We use t* values as estimated by the spectral fitting using only highest quality data (i.e., a signal-tonoise ratio >3.5) without any constrains on Q. This yields an average Q of 815. Using data from the Swiss Digital Seismic Network and the same approach, an average Q of 1,216 has been estimated (Edwards et al. 211). Our lower Q, which implies higher attenuation, seems reasonable considering that a Q of 1,216 represents an average for entire Switzerland and is mainly influenced by ray paths that sample the entire upper crust. Due to short source receiver distances in our dataset, rays travel only through the shallow upper crust, which can be expected to have a higher attenuation than the entire upper crust. Using an average Q of 815, we reran the spectral fitting method to compute f c values, which were then used to compute source radii. Data processing and quality control are crucial in the determination of source parameters using spectral fitting methods. This is especially important for small magnitude earthquakes, where the low-frequency spectral amplitudes are dominated by the background noise. Data processing follows, in general, the approach of Edwards et al. (21) with a few adaptations due to the short source receiver distances in our dataset. First of all, only data from stations located at the surface where used. Given the short source receiver distance of a few hundred meters, recordings at stations MFSFA and MFSFB were likely still influenced by the near field. All available waveforms are windowed to select parts of the data that are characterized by noise and signal. The signal window starts.25 s before the S-pick and continues for 2 s. It is consequently adjusted to include 5 75% of the cumulative squared velocity of the record (Raoof et al. 1999). The minimum signal window is restricted to 2 s. If not available, S-picks are estimated from available manually derived P-picks using a constant Vp/Vs ratio of Rescaling of the window length ensures that the position of the window is relatively insensitive to the quality of the P- and S-picks. The noise window starts at the beginning of the trace and continues over a duration equal to 75% of the travel time of the P- wave. This ensures that the noise window is as long as possible to correctly characterize the long-period noise and that the noise window is not contaminated by the P- wave arrival. Both signal and noise windows are zero padded to create equal length windows and to obtain the 2n samples needed for the fast Fourier transform (FFT). Before applying the FFT, both windows are demeaned and tapered using multitaper algorithms (Park et al. 1987). All data are then deconvolved with the instrument response to obtain true ground velocities. The results of these steps are two-sided Fourier ground velocity spectra for noise and signal of each trace. An example of adjusted signal and noise windows and corresponding velocity spectra are shown in Fig. 15. To select only the highest quality data, the noise spectrum is automatically shifted to intersect with the signal spectrum at both the lowest and highest frequencies of each spectrum (Edwards et al. 21). Only traces where the ratio between signal and noise spectra (SNR) is greater than a pre-defined threshold over a minimum frequency bandwidth of 3 11 Hz are selected. We selected an SNR of 1.5 based on visual inspection of the spectra fit of the source model and on the analysis of signal moment amplitudes. Data with SNR <1.5 did not provide stable spectra fits (Fig. 15). Moreover, signal moment amplitudes changed considerably for SNR <1.5, whereas amplitudes remained stable for SNR >1.5. In principle, all three components of a seismometer can be used independently in the spectral fitting. On the other hand, we observed significantly lower S-wave signal moment amplitudes for the vertical components. We attributed this to steep incidence angles due to the short source receiver distances in our data set, which focuses most of the S-wave energy on the horizontal components. We, therefore, used only the average of both horizontal components in the spectral fitting. Averaging of the horizontal components is done by calculating the geometrical mean of the frequency spectra of the east and north component. We did not rotate the components into the Raycoordinate system defined by the L, Q, T components due to inherently large uncertainties in estimating incident angles. We expect that uncertainties introduced by this rotation will outweigh the benefits of computing source spectra with a more appropriate coordinate system. In total, we could compute corner frequencies, and hence source dimensions, for 53 earthquakes out of 112 earthquakes recorded by the AlpTransit Network.