NOTE: Opening and Closing Reports must be enabled. See CL 2C Digit Positions 1 and 3 for additional information.

Transcription

1 SYSTM 6 Installation Manual L - 8 & - 68 ommand Location : Installer ombination igit Positions () - (6): Installer ombination ombination must have 6 digits. Valid entries are - 9. ommand Location - 8 and - 68: User rming Type and ombination = User (Master) = User = User = User = User 6 = User 6 7 = User 7 8 = User 8 (Guest) = User 9 = User = User ** = User = User 6 = User 7 = User 8 = User 6 9 = User 7 = User 8 = User 9 = User = User = User igit Position (): rming Type = rm Only, No losing () Report, No Shunting = isarm Only, No Opening (O) Report, No Shunting = rm and isarm, No O/ Reports, No Shunting = rm Only, with losing Report, No Shunting = isarm Only, with Opening Report, No Shunting 6 = rm and isarm, with O/ Reports, No Shunting = User 6 = User 6 = User 6 = User 6 6 = User 7 6 = User 8 6 = User 9 66 = User 67 = User 68 = User 7 = rm Only, No losing Report, Shunting llowed 8 = isarm Only, No Opening Report, Shunting llowed 9 = rm and isarm, No O/ Reports, Shunting llowed = rm Only, with losing Report, Shunting llowed = isarm Only, with Opening Report, Shunting llowed = rm and isarm, with O/ Reports, Shunting llowed igit Positions () - (6): rming ombination (PIN) ombination may have from - digits. Valid entries are -9. NOT: Opening and losing Reports must be enabled. See L igit Positions and for additional information. 9 ** are different for each user. Refer to the SYSTM 6 Programming Worksheet at the end of this manual for other user default values. NOT: Some programming locations allow variable-length data and require an nd-of-number (ON) character. Program ("") after the last digit. ill remain-ing unused Positions with "". The ON character is not required if the last digit is in Position PROGRMMING ONVRSIONS NOT: Some keypads may have a [SHIT] key and an [NTR] key in place of the [*] and [] keys, respectively. This manual uses the [*] for the [SHIT] key and the [] for the [NTR] key. 8

2 L 9 and SYSTM 6 Installation Manual ommand Location 9: rming/ombination Options 9 igit Position (): Guest ombination Time = Guest Time isabled = day = days = days = days = days 6 = 6 days 7 = 7 days 8 = 8 days 9 = 9 days = days = days = days = days = days = days igit Position (): ombination ommand = No = Yes; requires combination for ypass, Group ypass, Instant rm, keypad activated RPS, and Test (central station and bell) igit Position (): efault Installer ombination = No; this enables the Pirate-Guard TM feature for added security = Yes; combination changes back to factory value on power loss igit Position (): aulted rming Type = Goof-Proof: zones must be normal or shunted to arm = orce rm: faulted zones will be shunted at end of xit elay = hirp lert: faulted zones will chirp bell upon transition from xit elay to ntrance elay () () () () () igit Position (): utohome nable = No; this disables the utohome rming feature = Yes; when enabled, automatically shunts all zones designated as Group Shunt if exit door is not opened during xit elay (See L - igit Position for Group Shunt nable option) ommand Location : ommunications ormats igit Position (): Receiver Receiver ormat = ast "", Hz = Slow "", Hz = Sumheck, Hz = Sumheck, Hz = SK III 6 = TM, Hz () () () () igit Position (): Receiver Message ormat = / xtended = / (-digit reporting code) = SK III 6 = Sumheck (TM) igit Position (): Receiver Receiver ormat = ast "", Hz = Slow "", Hz = Sumheck, Hz = Sumheck, Hz = SK III 6 = TM, Hz igit Position (): Receiver Message ormat = / xtended = / (-digit reporting code) = SK III 6 = Sumheck (TM) Valid combinations of Receiver ormat and Message ormat are listed below. Message ormat Receiver ormat(s) / xtended ll formats, except SK III and TM, Hz / (-digit reporting) ast "", Hz and Slow "", Hz only SK III SK III only Sumheck (TM) TM, Hz only NOT: Some keypads may have a [SHIT] key and an [NTR] key in place of the [*] and [] keys, respectively. This manual uses the [*] for the [SHIT] key and the [] for the [NTR] key. PROGRMMING ONVRSIONS 9

3 SYSTM 6 Installation Manual L and ommand Location : ommunications igit Position (): elay efore ial Time = secs = secs = secs = secs = secs = secs 6 = 6 secs 7 = 7 secs 8 = 8 secs 9 = 9 secs = secs = secs = secs = secs = secs = secs 8 igit Position (): ial Type = TM - Touch Tone (/sec) = TM (/sec) = Pulse (/sec) igit Position (): nable Keypad ctivated RPS = No = Yes; allows remote programming to start from on-site keypad command igit Position (): RPS nable = No = Yes; allows remote programming to start from off-premise location igit Position (): Phone Ring Type = Single ring; uniformly timed rings with long pauses between rings = ouble ring; rings twice quickly followed by a long pause then rings twice again igit Position (6): ialing ttempts = try = tries = tries = tries = tries 6 = 6 tries 7 = 7 tries 8 = 8 tries 9 = 9 tries = tries = tries = tries = tries = tries = tries ommand Location : ccount Number ccount Number is used in conjunction with Receiver Number igit Positions () - (6): ccount Number Valid entries are -. The ccount Number is right justified. The last digit must be in Position (6). The SYSTM 6 will read the account number using: igit Positions () - (6) with -digit accounts igit Positions () - (6) with -digit accounts igit Positions () - (6) with 6-digit accounts ill all unused igit Positions with 's. PROGRMMING ONVRSIONS NOT: Some keypads may have a [SHIT] key and an [NTR] key in place of the [*] and [] keys, respectively. This manual uses the [*] for the [SHIT] key and the [] for the [NTR] key.

4 L - SYSTM 6 Installation Manual ommand Locations - : Receiver Phone Number Order in which the numbers will be dialed ommand Location ommand Location ommand Location ommand Location : Receiver Phone Number (digits - 6) igit Positions () - (6): - 9 = dialing digits = dial tone detect = * (TM dialing only, not used in pulse dialing) = (TM dialing only, not used in pulse dialing) = end of number = second delay igit () is dialed first. You must place a (ON) after the last digit to be dialed. ill in remaining positions with "". The zeroes will not be dialed. ommand Location : Receiver Phone Number (digits 7 - ) ommand Location : Receiver Phone Number (digits - 8) ommand Location : ccount Number ccount Number is used in conjunction with Receiver Number igit Positions () - (6): ccount Number Valid entries are -. The ccount Number is right justified. The last digit must be in Position (6). The SYSTM 6 will read the account number using: igit Positions () - (6) with -digit accounts igit Positions () - (6) with -digit accounts igit Positions () - (6) with 6-digit accounts ill all unused igit Positions with 's. NOT: Some keypads may have a [SHIT] key and an [NTR] key in place of the [*] and [] keys, respectively. This manual uses the [*] for the [SHIT] key and the [] for the [NTR] key. PROGRMMING ONVRSIONS

5 SYSTM 6 Installation Manual L - 6 ommand Locations - : Receiver Phone Number Order in which the numbers will be dialed ommand Location ommand Location ommand Location ommand Location : Receiver Phone Number (digits - 6) igit Positions () - (6): - 9 = dialing digits = dial tone detect = * (TM dialing only, not used in pulse dialing) = (TM dialing only, not used in pulse dialing) = end of number = second delay igit () is dialed first. You must place a (ON) after the last digit to be dialed. ill in remaining positions with "". The zeroes will not be dialed. ommand Location : Receiver Phone Number (digits 7 - ) ommand Location : Receiver Phone Number (digits - 8) ommand Locations - 6: RPS Phone Number ommand Location : RPS Phone Number (digits - 6) ommand Locations - 6 store the RPS Phone Number used by the the OMMNR II Remote Programming Software. or additional information on programming these Locations, refer to Receiver above. ommand Location : RPS Phone Number (digits 7 - ) ommand Location 6: RPS Phone Number (digits - 8) NOT: In order to utilize the Remote Programming feature, L, igit Positions () and () must also be programmed with YS. 6

6 L 7 - & - 7, - 6 & 9 - SYSTM 6 Installation Manual ommand Locations 7 - & - 7: Loop Reporting 7 = Loop 8 = Loop 9 = Loop = Loop = Loop = Loop 6 = Loop 7 = Loop 8 = Loop 9 = Loop = Loop ** = Loop = Loop = Loop 6 = Loop 7 = Loop 6 igit Positions () & (): larm Reporting ode Program to disable vent Reporting for a loop. 7 ** are different for each loop. Refer to the SYSTM 6 Programming Worksheet at the end of this manual. igit Positions () & (): Restore Reporting ode Program to disable vent Reporting for a loop. igit Positions () & (6): Shunt Reporting ode Program to disable vent Reporting for a loop. ommand Locations - 6, & 9 - : Loop = Loop = Loop = Loop = Loop = Loop = Loop 6 = Loop 7 6 = Loop 8 9 = Loop 9 = Loop ** = Loop = Loop = Loop = Loop = Loop = Loop 6 igit Position (): larm Receiver Select = Receiver with Receiver as back-up = Receiver only = Receiver and Receiver (ual Reporting) ** are different for each loop. Refer to the SYSTM 6 Programming Worksheet at the end of this manual. igit Position (): Loop Response Time = milliseconds = milliseconds = milliseconds = 7 milliseconds igit Position (): Loop Restore Type = No Restoral Report sent = Restoral sent when loop normal = Restoral sent when loop normal and bell silences = Restoral sent when loop normal and system disarmed igit Position (): Loop rming Type = Interior: delayed during / delays = Instant = elay = Long elay: delay two times as long = ay/instant: buzzer on day fault 6 = ay/elay: buzzer on day fault 7 = ay/instant with bell 8 = ay/elay with bell 9 = Hours: always armed igit Position (): Loop ell Type = Pulsing = Steady = hirp = Silent with no L = Silent with L igit Position (6): Loop ircuit Type = Normally Open ircuit = Normally losed ircuit = nd Of Line (OL) = Supervised, bell latched = Supervised, bell not latched NOT: Loop programmed as type or will report any open as a Trouble condition, regardless of panel armed status. PROGRMMING ONVRSIONS NOT: Some keypads may have a [SHIT] key and an [NTR] key in place of the [*] and [] keys, respectively. This manual uses the [*] for the [SHIT] key and the [] for the [NTR] key.

7 SYSTM 6 Installation Manual L 7-9 ommand Location 7: Soft Zone (mergency) This Zone is identified by the "" key on the lpha II and L keypads. 7 () () () () igit Positions () and (): mergency Report ode Program to disable alarm reporting for mergency zone. igit Position (): mergency Zone Receiver Select = Receiver with Receiver as back-up = Receiver only = Receiver and Receiver (ual Reporting) igit Position (): Loop ell Type = Pulsing = Steady = hirp = Silent NOT: ommand Location igit Position () must be programmed to YS to enable Soft Zones. ommand Location 8: Soft Zone (ire) This Zone is identified by the "" key on the lpha II and L keypads. 8 () () () () igit Positions () and (): ire Report ode igit Position (): ire Receiver Select igit Position (): Loop ell Type Refer to L 7 for information about programming this zone. ommand Location 9: Soft Zone (Police) This Zone is identified by the "P" key on the lpha II and L keypads. 9 () () () () igit Positions () and (): Police Report ode igit Position (): Police Zone Receiver Select igit Position (): Loop ell Type Refer to L 7 for information about programming this zone. PROGRMMING ONVRSIONS NOT: Some keypads may have a [SHIT] key and an [NTR] key in place of the [*] and [] keys, respectively. This manual uses the [*] for the [SHIT] key and the [] for the [NTR] key.

8 L and SYSTM 6 Installation Manual ommand Location : vent Reporting igit Position (): Shunt Receiver Select See also L 7 - & - 7 igit Positions () and (6). = Receiver with Receiver as back-up = Receiver only igit Position (): Restore Receiver Select See also L 7 - & - 7 igit Positions () and (). = Receiver with Receiver as back-up = Receiver only = Receiver and Receiver (ual Reporting) = Receiver and Receiver (ual Reporting) igit Position (): Unit Status Report ode Valid entries are -. The panel will add a fixed extension digit when reporting. ixed codes are listed below. Program a at this position to disable Unit Status Reporting. igit Position (): Unit Status Receiver Select = Receiver with Receiver as back-up = Receiver only = Receiver and Receiver (ual Reporting) igit Position (): ancel Report ode Valid entries are -. The panel will add the User I as the second digit when reporting. Program a at this position to disable ancel Reports. igit Position (6): ancel Report Receiver Select = Receiver with Receiver as back-up = Receiver only = Receiver and Receiver (ual Reporting) UNIT STTUS IX XTNSION OS = Low battery = fail = ell fuse fail = ailed to communicate 6 = attery restore 7 = restore 8 = ell fuse restore = Watchdog reset = ompleted programming ommand Location : Test Report 6 () () () () igit Positions () and (): Test Report ode Valid entries are -. Program to disable Test Reports. igit Positions (): Test Report Receiver Select = Receiver with Receiver as back-up = Receiver only igit Positions (): Test Report Interval = hour = hours = hours = hours = hours 6 = 7 days 7 = days 8 = days 9 = days = Receiver and Receiver (ual Reporting) = hour if armed = hours if armed = hours if armed = hours if armed = hours if armed NOT: L must be programmed to correctly set time of test.

9 SYSTM 6 Installation Manual L and ommand Location : Opening and losing Report igit Position (): Opening Report ode Valid entries are -. The User I is transmitted after the opening code. Program to disable Opening Reports. () () () () igit Position (): Opening Report Receiver Select = Receiver with Receiver as back-up = Receiver only igit Position (): losing Report ode Valid entries are -. The User I is transmitted after the opening code. Program to disable losing Reports. igit Position (): losing Report Receiver Select = Receiver and Receiver (ual Reporting) = Receiver with Receiver as back-up = Receiver only = Receiver and Receiver (ual Reporting) ommand Location : uress Report and elays 6 igit Position (): uress Report ode Valid entries are -. The User I will be reported as the second digit when reporting. Program to disable uress Reports. () () () () () igit Position (): uress Receiver Select = Receiver with Receiver as back-up = Receiver only = Receiver and Receiver (ual Reporting) igit Position (): ntry elay Time = secs = secs = secs = secs = secs 6 = 6 secs 7 = 7 secs 8 = 8 secs 9 = 9 secs = secs igit Position (): xit elay Time = secs = secs = secs = secs = secs 6 = 6 secs 7 = 7 secs 8 = 8 secs 9 = 9 secs = secs = secs = secs = secs = secs = secs = secs = secs = secs = secs = secs NOT: To program delay times greater than secs, see L - 6 & 9 - igit Position () NOT: To program delay times greater than secs, see L - 6 & 9 - igit Position () igit Position (): udible Time = min = min = min = min = min NOT: Some keypads may have a [SHIT] key and an [NTR] key in place of the [*] and [] keys, respectively. This manual uses the [*] for the [SHIT] key and the [] for the [NTR] key. PROGRMMING ONVRSIONS 6

10 L and SYSTM 6 Installation Manual ommand Location : udible/visual igit Position (): ntry Pre-alarm nable = No = Yes: sounds keypad buzzers during entry delay igit Position (): xit Pre-alarm nable = No = Yes: sounds keypad buzzers during exit delay igit Position (): ell Reverse Operation = No = Yes: supplies bell voltage in non-alarm state; ell requires external power supply () () () () () igit Position (): Ring ack = No = Yes: utomatic ell test after arming (and xit elay has expired) for local or non-supervised accounts; follows closing report for supervised accounts; sounds bells for seconds. igit Position (): isable Loop Ls = No = Yes: turns off keypad zone Ls after minutes ommand Location : Unit igit Position (): Local System Only = No = Yes: disables all communications except RPS () () () () () igit Position (): nable aily ynamic attery Test = No = Yes: performs a -minute battery test (under load conditions) once every hours igit Position (): nable our Minute Power-Up elay = No = Yes: all alarms suppressed for minutes on power-up igit Position (): nable Soft Zone Operation = No = Yes: allow use of mergency (), ire (), and Police (P) keys (See also L 7-9) igit Position (): Power Line requency = Hz = 6 Hz PROGRMMING ONVRSIONS NOT: Some keypads may have a [SHIT] key and an [NTR] key in place of the [*] and [] keys, respectively. This manual uses the [*] for the [SHIT] key and the [] for the [NTR] key. 7

11 SYSTM 6 Installation Manual L - & 8 ommand Locations - : Loop = Loop = Loop = Loop = Loop = Loop = Loop 6 6 = Loop 7 7 = Loop 8 8 = Loop 9 9 = Loop = Loop = Loop = Loop = Loop = Loop = Loop 6 () () () () igit Position (): nable oor hime = No = Yes: keypads beep seconds when faulted (disarmed condition) igit Position (): llow Shunting of This Loop = No: makes it a priority zone (not shuntable) = Yes: authorized users can bypass or force arm Refer to L - 8 & - 8 igit Position () for rming Types (uthorization Levels) igit Position (): llow Group Shunting for This Loop = No = Yes: include as part of group when performing Home rming or Instant/Home rming feature (See L 9 igit Position () and pages & ) igit Position (): elay efore ial = No = Yes: this loop will delay dialing on alarm for time programmed in () ommand Location 8: Trouble Reports igit Position (): Trouble Report ode This is a one-digit reporting code. Program to disable Trouble Report. 8 () () () () igit Position (): Trouble Report Receiver Select = Receiver with Receiver as back-up = Receiver only igit Position (): Trouble Restoral Report ode This is a one-digit reporting code. Program to disable Trouble Restoral Report. igit Position (): Trouble Restoral Report Receiver Select = Receiver with Receiver as back-up = Receiver only = Receiver and Receiver (ual Reporting) = Receiver and Receiver (ual Reporting) PROGRMMING ONVRSIONS NOT: Some keypads may have a [SHIT] key and an [NTR] key in place of the [*] and [] keys, respectively. This manual uses the [*] for the [SHIT] key and the [] for the [NTR] key. 8

12 L, and SYSTM 6 Installation Manual ommand Location : Test Report ountdown Timer This command will set the time when the first Test Report is transmitted to the central station. The panel will use this transmission time each time it's powered up or the PU is reset (unless ommand Location is reprogrammed). Previously stored data is not displayed during programming. () igit Position (): Set Test Report ountdown Timer = / hour = / hour = hour = hours = hours = hours 6 = 6 hours 7 = 8 hours 8 = hours 9 = hours = hours = 6 hours = 8 hours = hours = hours NOT: Refer to L for setting the time interval between Reports. = hours xample: The time is hours (: pm). You want the first Test Report to transmit at hours (: am). : pm + hours = : am. Program the value "8" in Memory Location. ommand Location : Set Real-Time lock (Year, Month, ay) This command will set the day, month, and year in the panel, and will not take effect until ommand is programmed. Previously stored data is not displayed during programming. () () () () () (6) igit Position (): Year - 's igit Position (): Year - 's igit Position (): Month - 's igit Position (): Month - 's igit Position (): ay - 's igit Position (6): ay - 's xample: If the date were pril, 99, would be programmed YR MONTH Y 9 ommand Location : Set Real-Time lock (Hour, Minute, Second) This command will set the hour, minute, and second in the panel. The time is set in (military time). Previously stored data is not displayed during programming. igit Position (): Hour - 's igit Position (): Hour - 's igit Position (): Minutes - 's igit Position (): Minutes - 's igit Position (): Seconds - 's igit Position (6): Seconds - 's xample: If the time were 8 and one-half minutes past in the afternoon, would be programmed HOUR MINUT SON 8 9

13 6 Programming Worksheet lient: SYSTM 6 Phone Number: ddress: Installer: ate: Location: VOLTS volts (term and ): UX POWR VOLTS (term and 6): TTRY VOLTS Under load - off: URRNT Keypads (term 6 and 8): UX POWR (term and 6): TOTL ( m allowed): + = ONTROL LOTION: RKR N LOTION: KYPS ddress 6 7 Location Installer ombination 9 User - Master User User User User 6 User 6 7 User 7 8 User 8 -Guest User 9 User User User User 6 User 7 User 8 User 6

14 9 User 7 User 8 User 9 User User User User 6 User 6 User 6 User 6 6 User 7 6 User 8 6 User User 6 7 User 6 8 User 9 rm/ombination Option ommunications ormats 8 ommunications ccount Phone (st 6 digits) (Middle 6 digits) (Last 6 digits) ccount Phone (st 6 digits) (Middle 6 digits) (Last 6 digits) RPS Phone (st 6 digits) (Middle 6 digits) (Last 6 digits) 6

15 7 Loop 8 Loop 9 Loop Loop Loop 6 6 Loop Loop Loop Loop 9 Loop Loop Loop Loop Loop 6 Loop 7 6 Loop 6 escription Volts Ohms Loop Loop Loop Loop Loop Loop 6 Loop Loop 8 9 Loop 9 Loop Loop

16 escription Volts Ohms Loop Loop Loop Loop Loop 6 7 mergency ire Zone 8 Zone 9 Police Zone vent Reports 6 Test Report Opening/losing Reports 6 uress/ elays udible/visual Unit 8 Trouble Reports Loop Loop Loop Loop Loop Loop 6 6 Loop 7 7 Loop 8 8 Loop 9 9 Loop Loop Loop Loop Loop Loop Loop 6 opyright 996 &K SYSTMS, Inc. ll Rights Reserved