ROTARY SELETOR SWITHES (SMD) S-3 RoHS compliant INTERNAL STRUTURE Part name Material Flammability FEATURES Wiper over Housing Terminal pin Base element Multi metal alloy Stainless steel (SUS 34) Epoxy opper alloy, Sn-u-plated eramic UL94V- O ring Silicone rubber UL94HB Rotor Polyphenylenesulphide UL94V- Electrode Ag-Pd cermet PART NUMBER DESIGNATION S - 3 - Z E T A Series name No. of poles pole No. of contacts contacts ontact timing ZNon-shorting (without neutral detent) Shape of terminal A, GJ-hook B, HGull wing Through hole pins Form of packaging TTaping (Reel) BlankBulk in plastic bag Terminal pin ESn-u (Lead-free) Please refer to the LIST OF PART NUMBERS when placing orders.
S-3 ROTARY SELETOR SWITHES (SMD) SHEMATIS DIAGRAMS pole contacts Series Switching specifications Schematic ON W S-3-ZEA ZEB ZE ZEG ZEH W W W W OFF W W W ON W W LIST OF PART NUMBERS ircuit type Setting position Form of packaging A, G J-hook B, H Gull wing Through hole pins Pieces in package pole contacts Whitout neutral detent Top setting Side setting Taping Plastic bag Taping Plastic bag S-3-ZETA S-3-ZETB S-3-ZEA S-3-ZEB S-3-ZE S-3-ZETG S-3-ZETH S-3-ZEG S-3-ZEH 5 pcs. /reel pcs. /pack 5 pcs. /reel pcs. /pack Verify the above part numbers when placing orders. Taping version can be supplied only in reel unit.
S-3 ROTARY SELETOR SWITHES (SMD) STANDARD SPEIFIATIONS ELETRIAL HARATERISTIS ircuit type pole contacts ontact rating.5 VA Operating temperature range Storage temperature range 4 ~ 85 Maximum current Maximum voltage ma 6 V Sealing Washable by O ring Please refer to page 5, 5 ontact timing ontact resistance Non-shorting maximum Net weight Approx..5g (A, B) Approx..6g () Approx..g (G, H) Insulation resistance Dielectric strength M (D5 V) minimum A5 V, 6 s MEHANIAL HARATERISTIS ENVIRONMENTAL HARATERISTIS No. of positions Adjustment torque 5 mn m {5 gf cm} maximum Vibration Amplitude.5 mmor Acceleration 98 m/s, -5- Hz, 3 directions for 3 times each Stopper strength mn m {4 gf cm} minimum Shock 49 m/s, ms 6 directions for 3 times each Stepping angle 5 ± 5 Load life 5 cycles minimum D6 V 3 ma Solderability Sn-u (lead-free)45 ± 3, ~ 3 s Humidity (Steady state) 4, Relative humidity 9 ~ 95 %, 4 h High temperature exposure 85, 96 h Soldering heat Sn-u (Lead-free) Flow : 6 ± 3 as the temperature in a pot of molten solder, immer sion from head of terminal to backside of board, 5 ~ 6 s, two times maximum. Reflow : Peak temperature 55 (Please refer to the profile below.) Manual soldering : 35 ±, 3 ~ 4 s Low temperature exposure 4, 96 h Thermal shock 4 (.5 h) ~ 85 (.5 h), 5 cycles Reflow profile for soldering heat evaluation Shear (Adhesion) Substrate bending Pull-off strength 5 N {.5 kgf}, s Width 9 mm, bend 3 mm, 5 s, time 5 N {.5 kgf}, s { } : Reference only Temperature () 5 5 5 8 5 Peak : 5 +5 Over 3 Pre Heating Zone 9 3 s 3 s Soldering Zone Heating time Reflow : two times maximum
S-3 ROTARY SELETOR SWITHES (SMD) OUTLINE DIMENSIONS Unless otherwise specified, tolerance: ±.3 (Unit: mm) S-3-ZEA digit (Location reversed every years).6 3.5 S-3-ZEB digit (Location reversed every years) W W W W.9L.5..7 t =. 4.4 W.5 W.9L..7 t =. S-3-ZE digit (Location reversed every years) W W.5W.9L.45D 3.5 t =. W W W.3 4 No plating on the cut surface W.5 max..7 S-3-ZEG digit (Location reversed every years). 3.5 Operating face.4.6.6 4.7..7 W W 3.6.9L W W
S-3 ROTARY SELETOR SWITHES (SMD) OUTLINE DIMENSIONS Unless otherwise specified, tolerance: ±.3 (Unit: mm) S-3-ZEH digit (Location reversed every years).9l. 3.5 Operating face.4.6.6 4.7.3.7.4 W W t =. 3.6 W W REOMMENDED P..B. PAD OUTLINE DIMENSIONS S-3-ZEA, ZEG S-3-ZEB, ZEH.6.6 (Unit: mm).5.9 4.6..9. 6..8 3...9..8 3..
S-3 ROTARY SELETOR SWITHES (SMD) PAKAGING SPEIFIATIONS <Taping packaging specifications> Embossed tape dimensions Reel dimensions (Unit: mm) (onforms to JIS 86-3) (In accordance with EIAJ ET-7A) End Empty Filled Empty 4 mm min. pitches min. Direction of feed 4 mm min. Head φ ±.8 ±.5 3±. φ 8.5(Top setting type) φ 54± (Side setting type) φφ + 3 (ETA/ETB) + (ETG/ETH) 6 (ETA/ETB) 5 min. (ETG/ETH) + φ 5.4± (ETA/ETB) 7.4± (ETG/ETH) S-3-ZETA/S-3-ZETB S-3-ZETG/S-3-ZETH (Unit: mm) (onforms to JIS 86) 8..3. 8. φ.5 +. 4..5.75. Installation example (S-3EA) φ.5 +.. 4..75..4. Installation example (S-3EH) 5.5.5 5.5. Direction of feed.5 Direction of feed 5.5 max. <Bulk pack specifications>