Page of 8 M Pak 0 Plug, PK0 series PK0-XXXPX-X-DA M Pak 0 Socket, PK0 series PK0-XXXSX-X-DA Product Specification Revised 08-0-
Page of 8 Table of Contents Title Page............................................................................. Contents..............................................................................0 Scope..................................................................................0 M Customer Documents..............................................................0 Performance Testing..................................................................0 Performance and Characteristics Overview........................................ 5.0 Electrical.................................................................... 6.0 Mechanical.................................................................... 7.0 Physical....................................................................... 5 8.0 Environmental.................................................................... 5 9.0 Qualification Test Groups and Sequences........................................ 7 Important Notice.................................................................... 8 Warranty Information................................................................. 8 Steven A. Neu: Approved 08-0- Jim W. Wessman: Approved 08-0-
Page of 8.0 Scope This document summarizes test methods, test conditions, and product performance requirements for M Pak 0 Socket PK0 Series mated to M Pak 0 Plug PK0 Series. In the event of performance data conflicts between this specification and any documents listed below, this specification supersedes those documents. Materials and finishes listed in the documents below apply and are included in this specification for reference only..0 M Customer Documents 78-500-077-6 Technical data sheet for Pak 0 Plug PK0 Series 78-500-078- Techical data sheet for Pak 0 Socket PK0 Series.0 Performance Testing Unless otherwise specified, all tests shall be performed on PK0-XXXSX-X-DA sockets mated to PK0-XXXPX-X-DA plugs at ambient environmental conditions per EIA-6. Unless otherwise specified, all values and limits are typical of those obtained by qualification testing of the subject product. All specifications are subject to revision and change without notice from M..0 Performance and Characteristics Overview. Ratings Dielectric Withstanding Voltage: 5 VACrms at sea level for minute Current (AC or DC): 0.5 A Temperature: -55 C to +85 C Insulation resistance: > x0 9 Ω at 500 VDC. Materials Socket: Material: Glass filled LCP Flammability: UL 9V-0 Color: White Contact Material: Copper Alloy Plug: Material: Glass Filled LCP Flammability: UL 9V-0 Color: White Contact Material: Copper Alloy. Finishes Plating: Underplating: 0μ"[.0 μm]nickel Wiping Area: μ" [ 0.05 μm ] min. Gold Solder Tails: Gold Flash Retaining Clips: Gold Flash over 0μ"[.0 μm] Nickel
Page of 8. Regulatory Compliance See Regulatory Information Appendix (RIA) in the RoHS compliance section of www.mconnector.com for compliance information. See customer drawings for regulatory specifics on each connector. 5.0 Electrical Description or Parameter Dielectric Withstanding Voltage (DWV) Current Rating: All Contacts in Series Low Level Contact Resistance (LLCR) Specification No dielectric breakdown or arcing. Temperature Rise: < 0⁰C Results: 0.5 A =5⁰C Temp. Rise Max R: <50 mω Apply 5 VAC RMS Voltage for minute betweeen adjacent contacts. Ambient: ⁰C Wire Measurement Current: ma DC Test Method Results Insulation Resistance (IR) 000 MΩ min. Apply 500V DC for minute between two adjacent contacts. 6.0 Mechanical Description or Parameter Specification Test Method Test Standard or Method Physical Shock No electrical discontinuity > µ sec Acceleration: 50G Shock Mode: half sine wave Duration: ms x in each X,Y,Z opposite direction 00mA DC applied to all contacts in series
Page 5 of 8 Vibration Peel-Off Test No electrical discontinuity > µ sec No damage to connector. No cracking or peeling at the leads. Frequency: 0-55 Hz Amplitude:.5 mm Sweep time: min hours in each X,Y,Z opposite direction 00 ma applied to all contacts in series Reflow Soldering Conditions: Temperature: < 50⁰C Duration: min. Thickness of cream solder: 0.5 mm Insertion Force Withdrawal Force (Contact Retention) Durability (00 times) Durability (500 times) Insertion Force: < 7.8 kg (00 pins) Withdrawal Force: <.0 kg (00 pins) LLCR: 50 mω Max LLCR: 50 mω Max Post Reflow Requirements: Force to peel-off leads at 0 mm/min must be > 50g/pin Measure with mating connectors Measure with mating connectors 00 cycles at 00-600 cycles per hour 500 cycles at 000 cycles per hour 7.0 Physical Description or Parameter Specification Test Method Result Visual Conforms to the design drawings Visual Inspection 8.0 Environmental Description or Parameter Specification Requirement or Conditions Test Standard or Method Temperature Life (Thermal Aging) LLCR: 50 mω Max No Damage or Deformation Temperature: +85⁰C Duration: 500 hours No serious corrosion Temperature: +5⁰C Salt Spray LLCR: 50mΩ Max Duration: 96 hours Concentration: 5%. -55⁰C for 0 min Thermal Shock. +5⁰C for 5 min Repeat -, 5 ( 5 cycles, -55⁰C to +85⁰C ). +85⁰C for 0 min. +5⁰C for 5 min cycles Humidity: 90-95% RH Humidity DWV: No breakdown or arcing Temperature: 0⁰C IR: 000 MΩ Min Duration: 96 hrs
Page 6 of 8 No serious corrosion. Temperature: 0⁰C H S Exposure LLLCR: 50 mω Max Concentration: ppm RH: 80% Duration: 96 hours No serious corrosion. Temperature: 0⁰C SO Exposure LLLCR: 50 mω Max Concentration: 0 ppm RH: 80% Duration: 96 hours No damage. Conditions: LLLCR: 50 mω Max hrs. () 5⁰C to 65⁰C.5 () 65⁰C.0 () 65⁰C to 5⁰C.5 () 5⁰C to 65⁰C.5 (5) 65⁰C.0 Moisture (6) 65⁰C to 5⁰C.5 (7a) 5⁰C 8.0 (7b) -0⁰C.0 Humidity 90-98% Humidity 80-98% 0 cycles of steps 7 Reflow Conditions: Resistance to Soldering Heat 50⁰C 00⁰C Peak min.
Page 7 of 8 9.0 Qualification Test Groups and Sequences 9. Sequenced Tests Test or Examination A B Test Group C D E F G Visual Insulation Resistance Dielectric Withstanding Volatge Low Level Contact Resistance Total Insertion Force Total Withdrawal Force Thermal Shock Vibration Shock Humidity Durability (00) Salt Spray S0 Exposure HS Exposure Temperature Life Moisture 5 6 7 8 9 5 6 7 5, 5 9. Independent Tests Durability (500) Dielectric Withstanding Voltage Current Rating Insulation Resistance 5 Mating Force / Contact 6 Unmating Force / Contact 7 Resistance to Soldering Heat 8 Peel-off
Page 8 of 8 M is a trademark of M Company. Important Notice All statements, technical information, and recommendations related to M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of M. Warranty; Limited Remedy; Limited Liability This product will be free from defects in material and manufacture for a period of one () year from the time of purchase. M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at M s option, to replace or repair the M product or refund the purchase price of the M product. Except where prohibited by law, M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this M product, regardless of the legal theory asserted. M 0. All rights reserved.