EE C245 ME C218 Introduction to MEMS Design
|
|
|
- Harvey Walker
- 5 years ago
- Views:
Transcription
1 EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA Lecture 23: Electrical l Stiffness EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 1
2 Lecture Outline Reading: Senturia, Chpt. 5, Chpt. 6 Lecture Topics: Energy Conserving Transducers Charge Control Voltage Control Parallel-Plate Capacitive Transducers Linearizing Capacitive Actuators Electrical Stiffness Electrostatic Comb-Drive 1 st Order Analysis 2 nd Order Analysis EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 2
3 Linearizing the Voltage-to-Force Transfer Function EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 3
4 Linearizing the Voltage-to-Force T.F. Apply a DC bias (or polarization) voltage V P together with the intended input (or drive) voltage v i (t), where V P >> v i (t) v(t) = V P + v i (t) EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 4
5 Differential Capacitive Transducer The net force on the suspended d center electrode is EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 5
6 Remaining Nonlinearity (Electrical l Stiffness) EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 6
7 Parallel-Plate Capacitive Nonlinearity Example: clamped-clamped laterally driven beam with balanced electrodes Nomenclature: V a or v A v a = v a cosωt Electrode Conductive Structure k m V A d 1 V a or v A = V A + v a t m x AC or Signal Component Total Value (lower case variable; v 1 DC Component lower case subscript) (upper case variable; V 1 upper case subscript) V P F d1 EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 7
8 Parallel-Plate Capacitive Nonlinearity Example: clamped-clamped laterally driven beam with balanced electrodes Expression for C/ x: Electrode Conductive Structure k m d 1 m x v 1 F d1 V 1 V P EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 8
9 Parallel-Plate Capacitive Nonlinearity Thus, the expression for force from the left side becomes: Electrode Conductive Structure k m d 1 m x v 1 F d1 V 1 V P EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 9
10 Parallel-Plate Capacitive Nonlinearity Retaining only terms at the drive frequency: F d C o 1 2 C o 1 1 = VP v cosωot VP x sin ωot ω o 2 d d 1 Drive force arising from the Proportional to input excitation voltage at displacement the frequency of this voltage 90 o phase-shifted from drive, so in phase with displacement These two together th mean that t this force acts against the spring restoring force! A negative spring constant Since it derives from V P, we call it Co1 2 ε the electrical stiffness, given by: ke = VP1 = V 2 P A EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 10 d 1 d 1
11 Electrical Stiffness, k e The electrical stiffness k e behaves like any other stiffness It affects resonance frequency: k k m k = = m m Electrode e ωo d 1 k = m k 1 m k e m 2 V = 1 1 P εa ω o ω o 3 k d m 1 Frequency is now a function of dc-bias V P v 1 V 1 V P Conductive Structure k m m F d1 x EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 11
12 Voltage-Controllable Center Frequency Gap EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 12
13 Microresonator Thermal Stability 1.7ppm/ o C Poly-Si μresonator - 17ppm/ o C Thermal stability of poly-si micromechanical resonator is 10X worse than the worst case of AT-cut quartz crystal EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 13
14 Geometric-Stress Compensation Use a temperature dependent mechanical stiffness to null frequency shifts due to Young s modulus thermal dep. [Hsu et al, IEDM 00] [W.-T. Hsu, et al., IEDM 00] Problems: stress relaxation compromised design flexibility [Hsu et al IEDM 2000] EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 14
15 Voltage-Controllable Center Frequency Gap EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 15
16 Excellent Temperature Stability Resonator Top Metal Electrode [Hsu et al MEMS 02] Top Electrode-to- Resonator Gap Elect. Stiffness: k e ~ 1/d 3 Frequency: f o ~ (k m - k e ) ppm/ o C Elect.-Stiffness Compensation 0.24ppm/ o C AT-cut Quartz Crystal at Various Cut Angles Counteracts reduction in frequency due to Young s modulus temp. dependence Uncompensated μresonator 100 [Ref: Hafner] On par with quartz! EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 16
![Design/Performance: f o =10MHz, Q=4,000 V P =8V, h e =4μm d o =1000Å, h=2μm W r =8μm, L r =40μm [Hsu et al MEMS 02]](/docs-images/85/92740763/images/17-0.jpg "Measured Δf/f vs. T for k e - Compensated μresonators 1500 1000 500 0-500 -1000-1500 0.")
![24ppm/ o C 300 320 340 360 380 Temperature [K] V P -V C Slits help to release the stress generated by lateral l thermal](/docs-images/85/92740763/images/17-1.jpg "expansion linear TC f curves 0.24ppm/ o C!")
17 Design/Performance: f o =10MHz, Q=4,000 V P =8V, h e =4μm d o =1000Å, h=2μm W r =8μm, L r =40μm [Hsu et al MEMS 02] Measured Δf/f vs. T for k e - Compensated μresonators ppm/ o C Temperature [K] V P -V C Slits help to release the stress generated by lateral l thermal expansion linear TC f curves 0.24ppm/ o C!!! 16V 14V 12V 10V 9V 8V 7V 6V 4V 2V 0V CC EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 17
18 Can One Cancel k e w/ Two Electrodes? What if we don t like the dependence of frequency on V P? Can we cancel k e via a differential i input electrode configuration? F d2 F d1 k If we do a similar analysis for F d2 at Electrode 2: d 1 d 2 Subtracts from the F d1 term, as expected Co2 Fd 2 = VP v cos ωo t ω 2 2 o d + V 2 P2 2 C d o x sinω t o V Adds to the quadrature term k e s add, 1 V V 2 P no matter the electrode configuration! EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 18 v 1 Ele ectrode e 1 m x k m Electrod de 2 v 2
19 Problems With Parallel-Plate C Drive Nonlinear voltage-to-force transfer function Resonance frequency becomes dependent on parameters (e.g., bias voltage V P ) Output current will also take on nonlinear characteristics as amplitude grows (i.e., as x approaches d o ) Noise can alias due to nonlinearity Range of motion is small For larger motion, need larger gap but larger gap weakens the electrostatic force Large motion is often needed (e.g., by gyroscopes, V vibromotors, optical MEMS) v 1 F d2 F d1 Ele ectrode e 1 d 1 d 2 m x k k m Electrod de 2 v 2 V 1 V V 2 P EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 19
20 Electrostatic Comb Drive EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 20
21 Electrostatic Comb Drive Use of comb-capacitive tranducers brings many benefits Linearizes voltage-generated input forces (Ideally) eliminates dependence of frequency on dc-bias Allows a large range of motion y Stator Rotor z x Comb-Driven Folded Beam Actuator EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 21
22 Comb-Drive Force Equation (1 st Pass) Top View y x z x L f Side View EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 22
23 Lateral Comb-Drive Electrical Stiffness Top View y x z x L f Side View Again: C ( x ) = 2Nεhx C 2Nεh = d x d No ( C/ x) x-dependence no electrical stiffness: k e = 0! Frequency immune to changes in V P or gap spacing! EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 23
24 Typical Drive & Sense Configuration y z x EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 24
25 Comb-Drive Force Equation (2 nd Pass) In our 1 st pass, we neglected Fringing fields Parallel-plate l l capacitance between stator and rotor Capacitance to the substrate All of these capacitors must be included when evaluating the energy expression! Stator Rotor Ground Plane EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 25
26 Comb-Drive Force With Ground Plane Correction Finger displacement changes not only the capacitance between stator and rotor, but also between these structures and the ground plane modifies the capacitive i energy [Gary Fedder, Ph.D., UC Berkeley, 1994] EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 26
![Berkeley, 1994]](/docs-images/85/92740763/images/27-6.jpg "EE C245:")
27 Case: V r = V P = 0V C sp depends on whether or not fingers are engaged Capacitance Expressions Capacitance per unit length Region 2 Region 3 [Gary Fedder, Ph.D., UC Berkeley, 1994] EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 27
28 Comb-Drive Force With Ground Plane Correction Finger displacement changes not only the capacitance between stator and rotor, but also between these structures and the ground plane modifies the capacitive i energy [Gary Fedder, Ph.D., UC Berkeley, 1994] EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 28
29 Simulate to Get Capacitors Force Below: 2D finite element simulation 20-40% reduction of F e,x EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 29
30 Vertical Force (Levitation) W 1 dcsp 2 1 dcrp 2 1 dcrs F e, z = = Vs + Vr z 2 dz 2 dz + 2 dz d C sp, e + C Fe, z = Nx 2 dz For V r = 0V (as shown): ( V V ) 2 ( ) rs 2 1 rs EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 30 s V s r
![, UCB, 1990] See that F z is roughly proportional to z for z less than z o it s like an](/docs-images/85/92740763/images/31-1.jpg "electrical stiffness that adds to the mechanical stiffness F z γ V z 2 P ( z z ) o z o = k e ( z")
31 Simulated Levitation Force Below: simulated vertical force F z vs. z at different V P s [f/ Bill Tang Ph.D., UCB, 1990] See that F z is roughly proportional to z for z less than z o it s like an electrical stiffness that adds to the mechanical stiffness F z γ V z 2 P ( z z ) o z o = k e ( z z) o Electrical Stiffness EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 31
32 Vertical Resonance Frequency ω z /ω zo Vertical resonance frequency Vertical resonance frequency at V P = 0V k + k ω z z e = where z k V 2 e zo k z z ω = Lateral resonance frequency = γ z o Signs of electrical stiffnesses in MEMS: Comb (x-axis) k e = 0 Comb (z-axis) k e > 0 Parallel Plate k e < 0 EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 32
33 Suppressing Levitation Pattern ground plane polysilicon into differentially excited electrodes to minimize field lines terminating on top of comb Penalty: x-axis force is reduced EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 33
34 Force of Comb-Drive vs. Parallel-Plate Comb drive (x-direction) V 1 = V 2 = V S = 1V Differential Parallel-Plate (y-direction) V 1 = 0V, V 2 = 1V Parallel-plate generates a much larger force; but at the cost of linearity EE C245: Introduction to MEMS Design Lecture 23 C. Nguyen 11/20/08 34
EE C247B ME C218 Introduction to MEMS Design Spring 2016
EE C47B ME C18 Introduction to MEMS Design Spring 016 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 9470 Lecture EE C45:
EE C245 ME C218 Introduction to MEMS Design Fall 2007
EE C45 ME C8 Introduction to MEMS Design Fall 007 Prof. Clark T.C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 9470 Lecture 3: Input Modeling
EE 245: Introduction to MEMS Lecture 23m1: Capacitive Transducers CTN 11/15/11. Copyright 2011 Regents of the University of California
EE 45: Intrductin t MEMS Lecture 3m: Capacitive Transducers Vltage-Cntrllable Center requency Micrresnatr Thermal Stability.7ppm/ C Gap Ply-Si μresnatr -7ppm/ C EE C45: Intrductin t MEMS Design LecM C.
EE C245 - ME C218 Introduction to MEMS Design Fall Today s Lecture
EE C45 - ME C18 Introduction to MEMS Design Fall 003 Roger Howe and Thara Srinivasan Lecture 11 Electrostatic Actuators II Today s Lecture Linear (vs. displacement) electrostatic actuation: vary overlap
EE C245 ME C218 Introduction to MEMS Design
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 22: Capacitive
EE C245 ME C218 Introduction to MEMS Design Fall 2012
EE C245 ME C218 Introduction to MEMS Design Fall 2012 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture EE C245:
EE C245 ME C218 Introduction to MEMS Design Fall 2007
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 17: Energy
EE C245 ME C218 Introduction to MEMS Design
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 19: Resonance
Capacitive Sensor Interfaces
Capacitive Sensor Interfaces Bernhard E. Boser Berkeley Sensor & Actuator Center Dept. of Electrical Engineering and Computer Sciences University of California, Berkeley Capacitive Sensor Interfaces 1996
Transducers. Today: Electrostatic Capacitive. EEL5225: Principles of MEMS Transducers (Fall 2003) Instructor: Dr. Hui-Kai Xie
EEL55: Principles of MEMS Transducers (Fall 3) Instructor: Dr. Hui-Kai Xie Last lecture Piezoresistive Pressure sensor Transducers Today: Electrostatic Capacitive Reading: Senturia, Chapter 6, pp. 15-138
EE C245 ME C218 Introduction to MEMS Design
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 20: Equivalent
EE C245 ME C218 Introduction to MEMS Design
EE C45 ME C8 Introduction to MEMS Design Fall 007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 9470 Lecture 5: Output t
EE C245 ME C218 Introduction to MEMS Design Fall 2011
EE C245 ME C218 Introduction to MEMS Design Fall 2011 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture EE C245:
EE C245 ME C218 Introduction to MEMS Design
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 ecture 15: Beam
EE C245 ME C218 Introduction to MEMS Design Fall 2007
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 15: Beam
EE C245 ME C218 Introduction to MEMS Design Fall 2010
EE C245 ME C218 Introduction to MEMS Design Fall 2010 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture EE C245:
EE C245 ME C218 Introduction to MEMS Design
EE C45 ME C18 Introduction to MEMS Design Fall 008 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 9470 Lecture 6: Output
EE C245 ME C218 Introduction to MEMS Design
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 21: Gyros
EE C245 ME C218 Introduction to MEMS Design
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 12: Mechanical
EECS C245 ME C218 Midterm Exam
University of California at Berkeley College of Engineering EECS C245 ME C218 Midterm Eam Fall 2003 Prof. Roger T. Howe October 15, 2003 Dr. Thara Srinivasan Guidelines Your name: SOLUTIONS Circle your
EE C245 ME C218 Introduction to MEMS Design
EE C45 ME C8 Introduction to MEMS Deign Fall 007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Science Univerity of California at Berkeley Berkeley, CA 9470 Lecture 5: Output t Sening
EE C245 ME C218 Introduction to MEMS Design
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 16: Energy
EE C245 / ME C218 INTRODUCTION TO MEMS DESIGN FALL 2011 C. Nguyen PROBLEM SET #7. Table 1: Gyroscope Modeling Parameters
Issued: Wednesday, Nov. 23, 2011. PROBLEM SET #7 Due (at 7 p.m.): Thursday, Dec. 8, 2011, in the EE C245 HW box in 240 Cory. 1. Gyroscopes are inertial sensors that measure rotation rate, which is an extremely
E05 Resonator Design
POLITECNICO DI MILANO MSC COURSE - MEMS AND MICROSENSORS - 2018/2019 E05 Resonator Design Giorgio Mussi 16/10/2018 In this class we will learn how an in-plane MEMS resonator handles process variabilities,
EE C247B / ME C218 INTRODUCTION TO MEMS DESIGN SPRING 2014 C. Nguyen PROBLEM SET #4
Issued: Wednesday, Mar. 5, 2014 PROBLEM SET #4 Due (at 9 a.m.): Tuesday Mar. 18, 2014, in the EE C247B HW box near 125 Cory. 1. Suppose you would like to fabricate the suspended cross beam structure below
EE C245 ME C218 Introduction to MEMS Design Fall 2007
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 13: Material
Comb Resonator Design (1)
Lecture 5: Comb Resonator Design (1) Sh School of felectrical ti lengineering i and dcomputer Science, Si Seoul National University Nano/Micro Systems & Controls Laboratory Email: dicho@snu.ac.kr URL:
Transduction Based on Changes in the Energy Stored in an Electrical Field
Lecture 6-1 Transduction Based on Changes in the Energy Stored in an Electrical Field Electric Field and Forces Suppose a charged fixed q 1 in a space, an exploring charge q is moving toward the fixed
EE C245 / ME C218 INTRODUCTION TO MEMS DESIGN FALL 2009 PROBLEM SET #7. Due (at 7 p.m.): Thursday, Dec. 10, 2009, in the EE C245 HW box in 240 Cory.
Issued: Thursday, Nov. 24, 2009 PROBLEM SET #7 Due (at 7 p.m.): Thursday, Dec. 10, 2009, in the EE C245 HW box in 240 Cory. 1. Gyroscopes are inertial sensors that measure rotation rate, which is an extremely
EE C247B / ME C218 INTRODUCTION TO MEMS DESIGN SPRING 2014 PROBLEM SET #1
Issued: Thursday, Jan. 30, 2014 PROBLEM SET #1 Due (at 9 a.m.): Wednesday Feb. 12, 2014, in the EE C247B HW box near 125 Cory. This homework assignment is intended to give you some early practice playing
Midterm 2 PROBLEM POINTS MAX
Midterm 2 PROBLEM POINTS MAX 1 30 2 24 3 15 4 45 5 36 1 Personally, I liked the University; they gave us money and facilities, we didn't have to produce anything. You've never been out of college. You
EE C245 - ME C218 Introduction to MEMS Design Fall Today s Lecture
EE C45 - ME C8 Introduction to MEMS Design Fall 3 Roger Howe and Thara Srinivasan Lecture 9 Energy Methods II Today s Lecture Mechanical structures under driven harmonic motion develop analytical techniques
INF5490 RF MEMS. LN03: Modeling, design and analysis. Spring 2008, Oddvar Søråsen Department of Informatics, UoO
INF5490 RF MEMS LN03: Modeling, design and analysis Spring 2008, Oddvar Søråsen Department of Informatics, UoO 1 Today s lecture MEMS functional operation Transducer principles Sensor principles Methods
CHAPTER 5 FIXED GUIDED BEAM ANALYSIS
77 CHAPTER 5 FIXED GUIDED BEAM ANALYSIS 5.1 INTRODUCTION Fixed guided clamped and cantilever beams have been designed and analyzed using ANSYS and their performance were calculated. Maximum deflection
Optimizing the Performance of MEMS Electrostatic Comb Drive Actuator with Different Flexure Springs
Optimizing the Performance of MEMS Electrostatic Comb Drive Actuator with Different Flexure Springs Shefali Gupta 1, Tanu Pahwa 1, Rakesh Narwal 1, B.Prasad 1, Dinesh Kumar 1 1 Electronic Science Department,
1. Narrative Overview Questions
Homework 4 Due Nov. 16, 010 Required Reading: Text and Lecture Slides on Downloadable from Course WEB site: http://courses.washington.edu/overney/nme498.html 1. Narrative Overview Questions Question 1
Lecture 23: Negative Resistance Osc, Differential Osc, and VCOs
EECS 142 Lecture 23: Negative Resistance Osc, Differential Osc, and VCOs Prof. Ali M. Niknejad University of California, Berkeley Copyright c 2005 by Ali M. Niknejad A. M. Niknejad University of California,
CHAPTER 4 DESIGN AND ANALYSIS OF CANTILEVER BEAM ELECTROSTATIC ACTUATORS
61 CHAPTER 4 DESIGN AND ANALYSIS OF CANTILEVER BEAM ELECTROSTATIC ACTUATORS 4.1 INTRODUCTION The analysis of cantilever beams of small dimensions taking into the effect of fringing fields is studied and
E08 Gyroscope Drive Design
POLITECNICO DI MILANO MSC COURSE - MEMS AND MICROSENSORS - 207/208 E08 Gyroscope Drive Design Paolo Minotti 26/0/207 PROBLEM We have to design the electronic circuit needed to sustain the oscillation of
An Accurate Model for Pull-in Voltage of Circular Diaphragm Capacitive Micromachined Ultrasonic Transducers (CMUT)
An Accurate Model for Pull-in Voltage of Circular Diaphragm Capacitive Micromachined Ultrasonic Transducers (CMUT) Mosaddequr Rahman, Sazzadur Chowdhury Department of Electrical and Computer Engineering
Modeling and simulation of multiport RF switch
Journal of Physics: Conference Series Modeling and simulation of multiport RF switch To cite this article: J Vijay et al 006 J. Phys.: Conf. Ser. 4 715 View the article online for updates and enhancements.
Experimental Validation of Damping Model for a MEMS Bistable Electrostatic Energy Harvester
Journal of Physics: Conference Series 557 (24) 24 doi:.88/742-6596/557//24 Experimental Validation of Damping Model for a MEMS Bistable Electrostatic Energy Harvester C H Nguyen, D S Nguyen 2 and E Halvorsen
MEAM 550 Modeling and Design of MEMS Spring Solution to homework #4
Solution to homework #4 Problem 1 We know from the previous homework that the spring constant of the suspension is 14.66 N/m. Let us now compute the electrostatic force. l g b p * 1 1 ε wl Co-energy =
Abstract. 1 Introduction
In R. A. Adey et al., eds., Simulation and Design of Microsystems and Microstructures (Proceedings of the 1st International Conference on Simulation and Design of Microsystems and Microstructures), Computational
Experimental analysis of spring hardening and softening nonlinearities in. microelectromechanical oscillators. Sarah Johnson
Experimental analysis of spring hardening and softening nonlinearities in microelectromechanical oscillators. Sarah Johnson Department of Physics, University of Florida Mentored by Dr. Yoonseok Lee Abstract
Transduction Based on Changes in the Energy Stored in an Electrical Field
Lecture 6- Transduction Based on Changes in the Energy Stored in an Electrical Field Actuator Examples Microgrippers Normal force driving In-plane force driving» Comb-drive device F = εav d 1 ε oε F rwv
Transduction Based on Changes in the Energy Stored in an Electrical Field. Lecture 6-5. Department of Mechanical Engineering
Transduction Based on Changes in the Energy Stored in an Electrical Field Lecture 6-5 Transducers with cylindrical Geometry For a cylinder of radius r centered inside a shell with with an inner radius
EE C245 - ME C218. Fall 2003
EE C45 - E C8 Introduction to ES Design Fall Roger Howe and Thara Srinivasan ecture 9 Energy ethods II Today s ecture echanical structures under driven harmonic motion develop analytical techniques for
Research Article The Effects of Structure Defects on the Performance of a Micro Comb Resonator
Mathematical Problems in Engineering Volume 2010, Article ID 726843, 12 pages doi:10.1155/2010/726843 Research Article The Effects of Structure Defects on the Performance of a Micro Comb Resonator D. Guo
Design and Analysis of dual Axis MEMS Capacitive Accelerometer
International Journal of Electronics Engineering Research. ISSN 0975-6450 Volume 9, Number 5 (2017) pp. 779-790 Research India Publications http://www.ripublication.com Design and Analysis of dual Axis
Four Degrees-of-Freedom Micromachined Gyroscope
Microsystems Laboratory Technical Report Four Degrees-of-Freedom Micromachined Gyroscope Cenk Acar 23 October 2001 Technical Report No: MSL-01003 cfl2001 Cenk Acar Contents Contents List of Figures Abstract
Design and Simulation of Comb Drive Capacitive Accelerometer by Using MEMS Intellisuite Design Tool
Design and Simulation of Comb Drive Capacitive Accelerometer by Using MEMS Intellisuite Design Tool Gireesh K C 1, Harisha M 2, Karthick Raj M 3, Karthikkumar M 4, Thenmoli M 5 UG Students, Department
EE C245 - ME C218 Introduction to MEMS Design Fall Today s Lecture
EE C45 ME C18 Introduction to MEMS Desin all 3 Roer Howe and Thara Srinivasan Lecture 1 Electrostatic Actuators I Today s Lecture Enery in electromechanical systems define carefully Parallelplate electrostatic
ENERGY HARVESTING TRANSDUCERS - ELECTROSTATIC (ICT-ENERGY SUMMER SCHOOL 2016)
ENERGY HARVESTING TRANSDUCERS - ELECTROSTATIC (ICT-ENERGY SUMMER SCHOOL 2016) Shad Roundy, PhD Department of Mechanical Engineering University of Utah shad.roundy@utah.edu Three Types of Electromechanical
EE C245 - ME C218. Fall 2003
EE C45 - ME C8 Introduction to MEMS Dein all 003 Roer Howe and Thara Srinivaan Lecture Electrotatic Actuator II EE C45 ME C8 all 003 Lecture Today Lecture Linear (v. diplacement) electrotatic actuation:
Last Name _Di Tredici_ Given Name _Venere_ ID Number
Last Name _Di Tredici_ Given Name _Venere_ ID Number 0180713 Question n. 1 Discuss noise in MEMS accelerometers, indicating the different physical sources and which design parameters you can act on (with
International Journal of ChemTech Research CODEN (USA): IJCRGG ISSN: Vol.7, No.2, pp ,
International Journal of ChemTech Research CODEN (USA): IJCRGG ISSN: 0974-4290 Vol.7, No.2, pp 678-684, 2014-2015 ICONN 2015 [4 th -6 th Feb 2015] International Conference on Nanoscience and Nanotechnology-2015
Sensors & Transducers 2016 by IFSA Publishing, S. L.
Sensors & Transducers, Vol. 96, Issue, January 206, pp. 52-56 Sensors & Transducers 206 by IFSA Publishing, S. L. http://www.sensorsportal.com Collapse Mode Characteristics of Parallel Plate Ultrasonic
The Pull-In of Symmetrically and Asymmetrically Driven Microstructures and the Use in DC Voltage References
IEEE Instrumentation and Measurement Technology Conference Anchorage, AK, USA, 1-3 May 00 The Pull-In of Symmetrically and Asymmetrically Driven Microstructures and the Use in DC Voltage References L.A.
Lecture 15 OUTLINE. MOSFET structure & operation (qualitative) Review of electrostatics The (N)MOS capacitor
Lecture 15 OUTLINE MOSFET structure & operation (qualitative) Review of electrostatics The (N)MOS capacitor Electrostatics Charge vs. voltage characteristic Reading: Chapter 6.1 6.2.1 EE15 Spring 28 Lecture
ACTA TECHNICA NAPOCENSIS
599 TECHNICAL UNIVERSITY OF CLUJ-NAPOCA ACTA TECHNICA NAPOCENSIS Series: Applied Mathematics and Mechanics Vol. 55, Issue III, SIZE EFFECT ON THE DYNAMICAL BEHAVIOUR OF ELECTROSTATICALLY ACTUATED MEMS
Last Name _Piatoles_ Given Name Americo ID Number
Last Name _Piatoles_ Given Name Americo ID Number 20170908 Question n. 1 The "C-V curve" method can be used to test a MEMS in the electromechanical characterization phase. Describe how this procedure is
EE C245 ME C218 Introduction to MEMS Design Fall 2007
EE C245 ME C218 Introduction to MEMS Design Fall 2007 Prof. Clark T.-C. Nguyen Dept. of Electrical Engineering & Computer Sciences University of California at Berkeley Berkeley, CA 94720 Lecture 12: Mechanics
A parametric amplification measurement scheme for MEMS in highly damped media. Cadee Hall. Department of Physics, University of Florida
A parametric amplification measurement scheme for MEMS in highly damped media Cadee Hall Department of Physics, University of Florida Lee Research Group 1 ABSTRACT Micro-electro-mechanical systems (MEMS)
JOURNAL OF MICROELECTROMECHANICAL SYSTEMS, VOL. 13, NO. 5, OCTOBER Sudipto K. De and N. R. Aluru, Member, IEEE, Associate Member, ASME
JOURNAL OF MICROELECTROMECHANICAL SYSTEMS, VOL. 13, NO. 5, OCTOBER 2004 737 Full-Lagrangian Schemes for Dynamic Analysis of Electrostatic MEMS Sudipto K. De N. R. Aluru, Member, IEEE, Associate Member,
ELECTROSTATICALLY-DRIVEN RESONATOR ON SOI WITH IMPROVED TEMPERATURE STABILITY
ELECTROSTATICALLY-DRIVEN RESONATOR ON SOI WITH IMPROVED TEMPERATURE STABILITY A. Giridhar, F. Verjus, F. Marty, A. Bosseboeuf, Tarik Bourouina To cite this version: A. Giridhar, F. Verjus, F. Marty, A.
ECE421: Electronics for Instrumentation MEP382: Design of Applied Measurement Systems Lecture #2: Transduction Mechanisms
ECE421: Electronics for Instrumentation MEP382: Design of Applied Measurement Systems Lecture #2: Transduction Mechanisms Mostafa Soliman, Ph.D. April 28 th 2014 Slides are borrowed from Dr. Moahmed Elshiekh
DESIGN AND ANALYSIS OF ROTATION RATE SENSOR. Modeling of vibratory MEMs Gyroscope
DESIGN AND ANALYSIS OF ROTATION RATE SENSOR Modeling of vibratory MEMs Gyroscope 1 Priya.P.Shreshtha & 2 Sushas S.Mohite 1 Mechanical Department, Rajaram Bapu institute of Technology Islampur, Dist. Sangli,
Design of Electrostatic Actuators for MOEMS Applications
Design of Electrostatic Actuators for MOEMS Applications Dooyoung Hah 1,, Hiroshi Toshiyoshi 1,3, and Ming C. Wu 1 1 Department of Electrical Engineering, University of California, Los Angeles Box 951594,
Institute for Electron Microscopy and Nanoanalysis Graz Centre for Electron Microscopy
Institute for Electron Microscopy and Nanoanalysis Graz Centre for Electron Microscopy Micromechanics Ass.Prof. Priv.-Doz. DI Dr. Harald Plank a,b a Institute of Electron Microscopy and Nanoanalysis, Graz
A Comparison of Pull-in Voltage Calculation Methods for MEMS-Based Electrostatic Actuator Design
A Comparison of Pull-in Voltage Calculation Methods for MEMS-Based Electrostatic Actuator Design Abstract Sazzadur Chowdhury, M. Ahmadi, W. C. Miller Department of Electrical and Computer Engineering University
Design and characterization of in-plane MEMS yaw rate sensor
Sādhanā Vol. 34, Part 4, August 2009, pp. 633 642. Printed in India Design and characterization of in-plane MEMS yaw rate sensor K P VENKATESH, NISHAD PATIL, ASHOK KUMAR PANDEY and RUDRA PRATAP CranesSci
Dept. of Electrical & Computer Engineering, Dept. of Mechanical Engineering University of Bridgeport, Bridgeport, CT /08/2015
Design and Analysis of Three DOF Piezoelectric Vibration Energy Harvester Ravi Teja Purra Reddy, Xingguo Xiong, Junling Hu Dept. of Electrical & Computer Engineering, Dept. of Mechanical Engineering University
Final EE290G Intro to MEMS 12/16/98
Final EE290G Intro to MEMS 12/16/98 Name SID 1. (20 points) Using poly1 in the MCNC/MUMPS process: Fx Fy L b L a x y cxx = c yx c xy c yy Fx F y (1) (a) Calculate c xy, the constant relating the force
EE 5344 Introduction to MEMS CHAPTER 6 Mechanical Sensors. 1. Position Displacement x, θ 2. Velocity, speed Kinematic
I. Mechanical Measurands: 1. Classification of main types: EE 5344 Introduction MEMS CHAPTER 6 Mechanical Sensors 1. Position Displacement x, θ. Velocity, speed Kinematic dx dθ v =, = ω 3. Acceleration
19. Capacitive Accelerometers : A Case Study. 19. Capacitive Accelerometers : A Case Study. Introduction. Introduction (ctnd.)
19 Capacitive Accelerometers : A Case Study 19 Capacitive Accelerometers : A Case Study Fundamentals of Quasi-Static Accelerometers Position Measurement with Capacitance Capacitive Accelerometer Case Study
Development and Characterization of High Frequency Bulk Mode Resonators
Excerpt from the Proceedings of the COMSOL Conference 008 Hannover Development and Characterization of High Frequency Bulk Mode Resonators Hossein Pakdast 1*, Zachary James Davis 1 1 DTU Nanotech, Technical
A Vertical Electrostatic Actuator with Extended Digital Range via Tailored Topology
A Vertical Electrostatic Actuator with Extended Digital Range via Tailored Topology Yanhang Zhang and Martin L. Dunn Department of Mechanical Engineering University of Colorado at Boulder Boulder, CO 80309
874. The squeeze film effect on micro-electromechanical resonators
874. The squeeze film effect on micro-electromechanical resonators Shih-Chieh Sun 1, Chi-Wei Chung, Chao-Ming Hsu 3, Jao-Hwa Kuang 4 1,, 4 Department of Mechanical and Electromechanical Engineering National
MEMS Tuning-Fork Gyroscope Mid-Term Report Amanda Bristow Travis Barton Stephen Nary
MEMS Tuning-Fork Gyroscope Mid-Term Report Amanda Bristow Travis Barton Stephen Nary Abstract MEMS based gyroscopes have gained in popularity for use as rotation rate sensors in commercial products like
b. The displacement of the mass due to a constant acceleration a is x=
EE147/247A Final, Fall 2013 Page 1 /35 2 /55 NO CALCULATORS, CELL PHONES, or other electronics allowed. Show your work, and put final answers in the boxes provided. Use proper units in all answers. 1.
PIEZOELECTRIC TECHNOLOGY PRIMER
PIEZOELECTRIC TECHNOLOGY PRIMER James R. Phillips Sr. Member of Technical Staff CTS Wireless Components 4800 Alameda Blvd. N.E. Albuquerque, New Mexico 87113 Piezoelectricity The piezoelectric effect is
Today s Presentation
Today s Presentation MEMS Comb Drive Actuator to Vary Tension & Compression of a Resonating Nano-Doubly Clamped Beam for High-Resolution & High Sensitivity Mass Detection Adam Hurst 1 John Regis 1 Chou
Lecture 15 OUTLINE. MOSFET structure & operation (qualitative) Review of electrostatics The (N)MOS capacitor
Lecture 15 OUTLINE MOSFET structure & operation (qualitative) Review of electrostatics The (N)MOS capacitor Electrostatics t ti Charge vs. voltage characteristic Reading: Chapter 6.1 6.2.1 EE105 Fall 2007
EE C245 ME C218 Introduction to MEMS Design Fall 2012
TN 1/2/12 EE 245 ME 218 Introduction to MEMS Design Fall 212 Prof. lark T.-. Nguyen Dept. of Electrical Engineering & omputer Sciences University of alifornia at Berkeley Berkeley, A 9472 Lecture EE 245:
EE C247B ME C218 Introduction to MEMS Design Spring 2015
EE 247B/ME 218: Introduction to MEMS Design TN 2/24/15 EE 247B ME 218 Introduction to MEMS Design Spring 215 Prof. lark T.-. Nguyen Dept. of Electrical Engineering & omputer Sciences University of alifornia
EE C247B / ME C218 INTRODUCTION TO MEMS DESIGN SPRING 2016 C. NGUYEN PROBLEM SET #4
Issued: Wednesday, March 4, 2016 PROBLEM SET #4 Due: Monday, March 14, 2016, 8:00 a.m. in the EE C247B homework box near 125 Cory. 1. This problem considers bending of a simple cantilever and several methods
Introduction to Microeletromechanical Systems (MEMS) Lecture 9 Topics. MEMS Overview
Introduction to Microeletromechanical Systems (MEMS) Lecture 9 Topics MicroOptoElectroMechanical Systems (MOEMS) Grating Light Valves Corner Cube Reflector (CCR) MEMS Light Modulator Optical Switch Micromirrors
sensors ISSN by MDPI
Sensors 7, 7, 76-796 Review sensors ISSN 144-8 7 by MDPI www.mdpi.org/sensors Stability, Nonlinearity and Reliability of Electrostatically Actuated MEMS Devices Wen-Ming Zhang 1, *, Guang Meng 1 and Di
EE C247B ME C218 Introduction to MEMS Design Spring 2017
247B/M 28: Introduction to MMS Design Lecture 0m2: Mechanics of Materials CTN 2/6/7 Outline C247B M C28 Introduction to MMS Design Spring 207 Prof. Clark T.- Reading: Senturia, Chpt. 8 Lecture Topics:
ME 237: Mechanics of Microsystems : Lecture. Modeling Squeeze Film Effects in MEMS
ME 237: Mechanics of Microsystems : Lecture Squeeze Film Effects in MEMS Anish Roychowdhury Adviser : Prof Rudra Pratap Department of Mechanical Engineering and Centre for Nano Science and Engineering
COURSE OUTLINE. Introduction Signals and Noise Filtering Sensors: Piezoelectric Force Sensors. Sensors, Signals and Noise 1
Sensors, Signals and Noise 1 COURSE OUTLINE Introduction Signals and Noise Filtering Sensors: Piezoelectric Force Sensors Piezoelectric Force Sensors 2 Piezoelectric Effect and Materials Piezoelectric
Temperature stabilization of CMOS capacitive accelerometers
INSTITUTE OFPHYSICS PUBLISHING JOURNAL OFMICROMECHANICS ANDMICROENGINEERING J. Micromech. Microeng. 14 (2004) 559 566 PII: S0960-1317(04)71039-6 Temperature stabilization of CMOS capacitive accelerometers
Contactless Excitation of MEMS Resonant Sensors by Electromagnetic Driving
Presented at the COMSOL Conference 2009 Milan University of Brescia Department of Electronics for Automation Contactless Excitation of MEMS Resonant Sensors by Electromagnetic Driving Marco Baù, VF V.
arxiv: v1 [physics.app-ph] 26 Sep 2017
![arxiv: v1 [physics.app-ph] 26 Sep 2017](/thumbs/78/76951448.jpg "arxiv: v1 [physics.app-ph] 26 Sep 2017")
ON THE LATERAL INSTABILITY ANALYSIS OF MEMS COMB-DRIVE ELECTROSTATIC TRANSDUCERS Binh Duc Truong Cuong Phu Le and Einar Halvorsen. arxiv:79.877v [physics.app-ph] 6 Sep 7 Keywords: Lateral instability MEMS
INF5490 RF MEMS. LN06: RF MEMS switches, II. Spring 2012, Oddvar Søråsen Department of Informatics, UoO
INF5490 RF MEMS LN06: RF MEMS switches, II Spring 2012, Oddvar Søråsen Department of Informatics, UoO 1 Today s lecture Design of RF MEMS switches Electromechanical design, II RF design Examples of implementations
Research Article A Pull-in Based Test Mechanism for Device Diagnostic and Process Characterization
Hindawi Publishing Corporation VLSI Design Volume 8, Article ID 8, 7 pages doi:./8/8 Research Article A Pull-in Based Test Mechanism for Device Diagnostic and Process Characterization L. A. Rocha, L. Mol,
Lecture 20. Measuring Pressure and Temperature (Chapter 9) Measuring Pressure Measuring Temperature MECH 373. Instrumentation and Measurements
MECH 373 Instrumentation and Measurements Lecture 20 Measuring Pressure and Temperature (Chapter 9) Measuring Pressure Measuring Temperature 1 Measuring Acceleration and Vibration Accelerometers using
SENSORS and TRANSDUCERS
SENSORS and TRANSDUCERS Tadeusz Stepinski, Signaler och system The Mechanical Energy Domain Physics Surface acoustic waves Silicon microresonators Variable resistance sensors Piezoelectric sensors Capacitive
Proceedings of IMECE' ASME International Mechanical Engineering Congress and Exposition November 5-11, 2005, Orlando, Florida
DRAFT Proceedings of IMECE'5 5 ASME International Mechanical Engineering Congress and Exposition November 5-, 5, Orlando, Florida IMECE5-87 RESPONSE OF MEMS DEVICES UNDER SHOCK LOADS Mohammad I. Younis