CT30 Barcode Scanner U s e r Manual

Transcription

1 CT30 Barcode Scanner U s e r Manual

2 IMPORTANT NOTICE Safety Precaution * DO NOT disassemble the scanner, or place foreign matter into the scanner cause a short circuit or circuit damage. * DO NOT expose the scanner or battery to any flammable sources. Maintenances Precaution * Use a clean cloth to wipe dust off the body of the scanner. * If you find the scanner abnormal, write down the specific scenario and consult the maintenance person. Enviromental Paramenter Operating Temp. 0 to 50 ºC / 32 to 122 ºF Storage Temp. 0 to 50 ºC / 32 to 122 ºF Operating Humidity 20-85% (non-condensing) Storage Humidity 20-85% (non-condensing) 2

3 Contents IMPORTANT NOTICE Safety Precaution Maintenances Precaution Enviromental Paramenter...2 Contents...3 Overview o f CT30 Barcode Scanner Features of t h e Scanner...5 Appearance...5 Introduction of KeyFunction....6 Specifications Correct Aiming...7 Incorrect Aiming QUICK START E n t e r t h e Setting Mode E x i t t h e Setting Mode with S a v e E x i t t h e Setting Mode without S a v e Restore Factory Defaults Check Software V e r s i o n S a v e Custom Settings...11 Chapter 1 Features a n d Basic Setups Battery Mounting t h e battery (charging) Howt o operate CT20 Barcode Scanner AutoP o w e r Off T r a n s m i t Buffer Inventory Mode LED Indicator Beeper Beeper V o l u m e Scan Modes Manual Mode Continuous Mode AutoP o w e r OffMode Auto-induction Mode Symbologies Supported USBW i r e d DataTransmission...25 Chapter 2 Howt o Connect with BT Select Output Interface BT S P P Mode BT HIDMode

4 4

5 Overview of CT30 Barcode Scanner CT30 Bluetooth wireless barcode scanner,which is developed by our company, is a c o s t effective,small size,light weight, fits ergonomically,easy to carry,1d bar code scanner. CT30 bar code scan parts using the1d bar code scanning solutions of r e d light bar code scanning patent technology of CILICO, U s i n g 630nm r e d light indicates a CCD imaging technology a n d intelligent image recognition system, integrating high-performance processor a n d decoded board, with ability tor e a d fast decoding a n d high precision, high resistance to environmental interference. I t caneasily r e a d thebar code on thepaper, merchandise,etc...the barcode scanning distance ismuch improved thansimilar products, it scanning very fast, reading bar code highly exactly. CT30 Bluetooth barcode scanner has internal long distance wireless Bluetooth,and it can compatible with laptops, desktops or other real-time data transmission Bluetooth devices. The power source of it is a pair of replaceable A A batteries, When y o u ' r e outside of B T, the 256K memory can storetens of thousands of scanned information toensure thatyour data is security Features o f the Scanner *Smallsize, portable. *Supports three scan modes, including Continuous Mode, Manual Mode, Auto-off Mode *Supports most popular barcode symbologies *User feedback v i a L E D indicator a n d beeper *Thevoice volume of scan barcode successfully could change via setting barcode *Built-in KB F l a s h memory can store u p t o thousand scan barcodes. *Provides 2 KB memory for reserve buffer while Bluetooth connection interrupt, can store u p t o scan barcodes. * Supports BT SPP. * Supports BT HID. * Programmable parameters include data output format, editing format, symbologies, etc. 5

6 Appearance Introduction of Key Function 6

7 Note:P r e s s P o w e r button t u r n on/off T u r n off t h e scanner,press t h e mutifunction with P o w e r button t o clear t h e lastest pair information of record i n t h e CT30. P r e s s t h e multifunction t o sendt h e recorded bar code. Aftert u r n off t h e scanner,press t h e scan button with P o w e r button t o clear t h e recording bar code andt u r n ont h e scanner. Specifications Radio range 10m visual range Bluetooth Bluetooth class 2. 0 virsion+edr Sensor 2500 pixels Communication mode SPP,HID Light source Redlight LED 630± 20nm Decode capacity Codabar, Code 11, Code 93, MSI,Code128, UCC/EAN-128, Code 39, EAN-8, EAN-13,UPC-A,ISBN,Industrial 25,Industrial 25 Standard 25,2 / 5 Matrix Resolution 5 m il Scan distance 6~30cm Scan speed 200times/second indication Beeper,indicator Print contrast ratio 30% Cylinder Horizontal scan Diameter35mm Operating Temp. 0 to 5 0 º C / 3 2 to 122 ºF Storage Temp. 0 to 5 0 º C / 3 2 to 122 ºF Operating Humidity 20-85% (non-condensing) Storage Humidity 20-85% (non-condensing) Correct A i m i n g 7

8 Incorrect Aiming QUICK START The setting o f t h e CT30 Barcode Scanner can b e changed b y reading t h e setup barcodes contained i n t h i s manual. This section describes t h e procedure o f setting t h e CT30 Barcode Scanner b y reading t h e setup barcodes a n d provides some example for demonstration. Steps Action Feedback if Successful 1 Turn on CT30 Barcode Scanner... It will response with a long beep(high t o n e ), i t ' s L E D shows red a n d w i t h I n t m t twinkle. N o t e : How t h e CT30 Barcode Scanner establishes a connection w i t h computer o r other compatible device, please refer to Chapter 2. 2 Enter the Setting Mode... TheCT30 Barcode Scanner will response three beeps (tone descending from high t o l o w ), and i t s LED indicator will flashing purple. E n t e r S e t u p 3 Reada Setup barcode The CT30 Barcode Scanner will response three beeps (tone ascending from l o w t o high), a n d i t s LED indicator will flashing purple. For Example: Enable Codabar 4 Exit the Setting Mode... The CT30 Barcode Scanner will response three beeps (tone descending from high t o l o w ), and i t s L E D indicator 8

9 will not flashing purple and power off. E x i t with S a v e N o t e : When a n y setup error occurs, t h e CT30 Barcode Scanner will respond w i t h a l o n g beep (low tone), a n d i t s L E D indicator w i l l flashing purple. Steps of Setup: Enter Setup Details (eg: Enable/Disable a Barcode) Exit Setup Enter the Setting Mode F o r t h e scanner t o enter t h e setting mode, y o u must have i t read t h e "Enter Setup" barcode, w h i c h will b e located a t t h e bottom o f almost every page o f t h i s manual. TheCT30 Barcode Scanner will respond with three beeps (tone descending from high to l o w ), a n d i t s L E D indicator becomes purple a n d g o o f f quickly after reading t h e barcode. Enter Setup F o r setting scanner parameters, see "Reada Setup Barcode" below. Exit the Setting Mode with Save F o r t h e scanner t o e x i t t h e setting mode, y o u must h a v e i t read t h e "Exitw i t h Save" barcode, w h i c h will b e located a t t h e bottom o f almost every page o f t h i s manual. Just like reading the "Enter Setup" barcode, the scanner will respond with three beeps (tone ascending f r o m l o w t o high) after reading t h e barcode. 9

10 Exit with Save Exit the Setting Mode without Save I f y o u want t o e x i t t h e setting mode without saving a n y changes, y o u must h a v e t h e scanner read t h e "Exitwithout Save" barcode. Just like reading the "Enter Setup" barcode, the scanner will respond with three beeps (tone ascending f r o m l o w t o high) after reading t h e barcode. Exit without Save Restore Factory Defaults "RestoreFactory Defaults" is a special barcode. The CT30 Barcode Scanner will respond w i t h a short beep (high tone) after reading t h i s barcode. At t h i s t i m e, t h e scanner system could restore factory defaults, a n d n o need t o read "Exitw i t h Save" barcode again. The Scanner defaults enable HID, PIN defaults RestoreFactory Defaults N o t e : Most of setting mode have restore factory defaults selection. The factory default value for each setting i s indicated b y a n asterisk "*". Y o u could u s e t h i s barcode a t t h e following status: 1 The scanner can n o t w o r k. F o r example, i t can not read barcodes. 2 Y o u forget t h e settings y o u d i d t o t h e scanner before, a n d y o u don't want t o b e affected b y t h e settings when y o u u s e t h e scanner. 3 After u s i n g a function w h i c h i s n o t b e u s e d usually i n t h e scanner. 10

11 Check Software V e r s i o n I f y o u want t o know t h e software version o f CT30, should read t h e Enter Setup a n d Output Software V e r s i o n barcode: Enter Setup Output S o f t w a r e V e r s i o n Checking t h e software version i s done a t t h e enter setup mode, so after output t h e software version, need to read Exit without Save barcode. Exit without Save Save Custom Settings 1. You may change factory defaults, and customize some functions suitable for your own applications when you use CT30, you must read the Enter Setup Function barcode you want t o customize Save CustomSettings Exit w i t h Save barcodes. Enter Setup Save CustomSettings RestoreCustomsSettings 1 1

12 Exit with Save 2. If you want to restore to custom settings after resetting the barcode scanner, just need to read Enter Setup Restore Custom Settings Exit with Save barcodes as above. 12

13 Chapter 1 Features a n d Basic Setups This chapter will introduce t h e features a n d usage o f t h e CT30 barcode scanner. Contents 1.1Battery Mounting t h e battery(charging) Howt o operate CT30 Barcode Scanner AutoP o w e r Off T r a n s m i t Buffer LED Indicator Beeper Beeper V o l u m e Scan Modes Manual Mode Continuous Mode AutoP o w e r OffMode Auto-induction Mode Symbologies Supported USBW i r e d DataTransmission

14 1.1Battery The scanner is powered by two AA batteries or AAA alkaline batteries. The batteries can support the scanner work continuous for 60 hours, or read barcodes (read an EAN-13 barcode per 5s ) Mounting t h e battery (charging) 1) Hold t h e scanner face d o w n i n o n e hand. 2 )Press the back case and push like picture. 3 ) p u t i n t h e batteries. 4 )close t h e b a c k case H o w t o operate CT30 Barcode Scanner T u r n on t h e scanner Press t h e Power key for about 2 seconds. The scanner will respond w i t h a l o n g beep (high tone), a n d i t s L E D indicator i s flashing. T u r n off t h e scanner Press t h e Power key for about 3 seconds. The scanner w i l l respond w i t h t w o short beeps (high tone) a n d t h e L E D indicator i s t u r n off. 14

15

16 1.2Transmit Buffer Duringt h e Bluetooth connection, t h e CT30 Scanner u s e s a 2 K B memory a s a d a t a buffer, a n d sends t h e collected data t o t h e h o s t computer o n e b y one v i a t h e Bluetooth. Upon reading a barcode successfully, t h e scanner responds w i t h one short beep a n d i t s L E D indicator becomes green and goes o f f quickly. However, t h e h o s t computer may n o t receive the data immediately if getting out of range. With the 2KB transmit buffer, the scanner can ignore t h e transmission status a n d keep o n reading barcodes u n t i l t h e buffer i s full. When t h e buffer i s full, t h e scanner will respond w i t h a l o n g beep (low tone), t h i s reminds t h e u s e r t h a t t h e space o f buffer i s not enough a n d can not read barcode a n y Once t h e Buffer i s full, t h e u s e r should return t o t h e range o f BT connection quickly, t h e data i n t h e buffer can b e sent b a c k t o t h e h o s t computer a n d release t h e space of buffer. N o t e : The 2KB t r a n s m i t buffer o n t h e scanner can h o l d a s many a s barcodes bases o n EAN13. Y o u can choose t o clear t h e data i n t h e buffer e v e r y t i m e when y o u t u r n o n t h e scanner. Enable ClearDatai n Buffer When Turn On the Scanner *Disable Clear Data in Buffer When Turn On the Scanner N o t e : Y o u can clear t h e d a t a i n t h e buffer v i a enable barcode, y o u can a l s o clear t h e d a t a i n t h e buffer v i a p r e s s t h e Power key l o n g t i m e. After t h e Bluetooth connect successfully, t h e barcodes i n t h e buffer will upload t o appointed position automatically. You also can setup upload the barcodes in the buffer or n o t v i a read t h e following barcodes. By default, i t i s enabled. I f y o u d o n t want t o upload t h e barcodes automatically, y o u can setup a s disabled, when t h e Bluetooth connect, t h e barcodes w o n t upload. Y o u can double click Power key t o start upload t h e barcodes. (*)Enable Auto Uploading Disable Auto Uploading E n t e r S e t u p E x i t with S a v e E x i t without S a v e 16

17 1.2.1 Inventory Mode I f y o u want t o keep t h e barcodes i n t h e buffer o f CT30 for multiple uploading, y o u can choose inventory mode. I n inventory mode, CT30 w i l l count t h e number o f t h e barcodes automatically, and control t h e t i m e, position e t c. for uploading. Also, y o u can clear t h e barcodes i n t h e buffer after uploading. Following i s t h e setup method: 1 ) Read Enter Inventory Mode barcode t o enter i n t o t h e inventory mode Enter Inventory Mode 2 ) If you want to recover to normal mode, read the Enter Normal Mode barcode Enter Normal Mode 3 ) Read t h e Clear t h e barcodes i n t h e buffer barcode t o clear t h e barcodes (only suitable for inventory mode) Cleart h e barcodes i n t h e buffer 4 ) Read Data Uploading barcode t o upload t h e barcodes i n t h e buffer (only suitable for inventory mode) DataUploading 5 ) Read Upload Counting barcode to count the number of the barcodes (only suitable for inventory mode) Upload Counting Note:Inventory function can be used under any scan mode mentioned in

18 1.3 LED Indicator The L E D indicators o n CT30 can h e l p t h e u s e r know about t h e current operation status. Colorof LED Indicator Green L E D o n a n d o f f quickly Green L E D o n Every 5 s Purple, Flashing(On/Off ratio 1 :1 ) Blue, Flashing (On/Off ratio 1 :1 ) Blue, Flashing (On/Off ratio 20ms:3s) Red,Flashing (On/Off ratio 1 : 1 ) Meaning Good Read, w i t h o n e short beep (high tone) Indicates t h e CT30 Scanner i n M e m o r y M o d e Indicates the CT30 Scanner in Setting mode Indicates the BT is waiting for connection, the CT30 stores t h e address o f BT w h i c h connects w i t h t h e l a s t t i m e. Indicates t h e CT30 Scanner i s o u t o f range o r can not establish connection w i t h BT, w i t h t w o short beeps(high-low tone) Indicates t h e CT30 Scanner establish a BT connection successfully, w i t h t w o short beeps (low-high tone). Indicates t h e CT30 Scanner reconnect w i t h BT, w i t h two shortbeeps (low-high tone). Indicates the CT30 Scanner has no address of BT w h i c h connects w i t h before. The default BT connect interface i s HID, t h e PIN code i s

19 1.4Beeper The beeper built i n CT30 can h e l p t h e u s e r know about t h e current operation status. Beeping One long beep, high tone One short beep, h i g h t o n e One long beep, low tone Two short beeps, high tone T w o short beeps, low-high t o n e T w o short beeps, high-low t o n e Three short beeps, t o n e descending from high to low Three short beeps, t o n e ascending from l o w t o high Meaning Power o n. I f t h e scanner h a s n o BT address w h i c h could connect with, flashing red. If the scanner has BT address which could connect with, flashing blue. Readbarcode, w i t h green L E D o n a n d o f f quickly Configuration error, with purple flashing; Or transmit buffer full, with green LED on and off quickly Power off. BT connection established, with blue LED flashing (On/Off ratio 20ms:3s). BT connection o u t o f range o r suspended, w i t h b l u e L E D flashing (On/Off ratio 1 : 1 ). Enter o r Exit Setting mode, w i t h purple L E D flashing. Configuration correct, with purple LED flashing; 19

20

21 1.5Scan Modes Three kinds o f scan modes a r e supported b y t h e CT30 Barcode Scanner: Manual Mode By default, t h e scan mode i s set t o Manual Mode. I f t h e u s e r keeps p r e s s t h e Scan Key, t h e CT30 Scanner will e m i t a red light line. This indicates t h e scanner could scan, t h e scanning will not stop until the scanner under the following situation. * Reada barcode successfully; * Release t h e Scan Key. Manual Mode Enter Setup Exit with Save Exit without Save 21

22

23

24 Delay Between Re-Read The delay time between re-read of above scan modes could be set by the following barcode. 400ms 800ms 1s (*)2s 3s 5s 10s 15s For Example: 1. Read the "Enter Setup" barcode; 2. Read the "Auto Power off Mode" barcode; 3. Read the "1s" of the time interval between each scanning barcode; 4. Read the "Exit with Save" barcode. Then enter the Auto Power Off Mode. Enter Setup Exit with Save 24 Exit without Save

25 1.6Symbologies Supported M o s t o f t h e popular barcode symbologies a r e supported b y t h e CT30 Scanner, a s listed below. Refer t o Chapter 4 for details o f e a c h symbology. Symbologies Supported: Enable/Disable Pre-Set Codabar Disable Code1 1 Disable Code9 3 Disable M S I Disable Code1 2 8 Enable UCC/EAN-128 Enable Code3 9 Enable EAN/UPC EAN-8 Disable EAN-13 Enable UPC-A Enable UPC-E Enable ISBN Disable Code2 o f 5 Industrial 2 5 Disable Interleaved 25 Disable Standard 25 Disable 2 / 5 Matrix Disable 25

26 Chapter 2 H o w toconnect with BT 1 Make CT30 full charged, press Power key. If the scanner never connected with the computer before, it will responds with a beep, and flashing red. 2 Have t h e scanner read t h e "Enter Setup" barcode t o enter t h e setting mode. 3 Have t h e scanner read t h e associated barcode t o activate t h e BT connection interface. 4 Have the scanner read the barcodes for related settings. 5 Have t h e scanner read t h e barcode t o e x i t t h e setting mode. 6 The CT30 Scanner will stay active for 1 minute waiting for a connection request from the host(spp) or trying to connect to the host(hid). Contents 2.1.Select Output Interface BT S P P Mode BT HIDMode Setting upa BT connection Connect t o P C v i a BT Connect t o P D A v i a BT

27 2.1. Select Output Interface Either SPP o r HID can b e chosen depending o n t h e need BTSPPMode I f y o u select t h e output interface o f BT SPP, p o r t t o o l t o collect t h e scanned data. y o u may run HyperTerminal.exe o r serial Enable S P P You can setup SPP data batch upload or single upload according to your requirements. SPP Data Batch Upload SPP Data Single Upload BTH I D Mode By default, BT HID i s activated o n t h e CT30 Scanner, a n d t h e keyboard t y p e i s set t o PCAT (US). (*)Enable HID Enter Setup Exit with Save Exit without Save 27

28 2.2Setting up a BT connection Specify t h e PIN Code, i f y o u choose "TheDefault Value 1 ", t h e passkey for setting u p a BT connection i s 10010; I f y o u choose "TheDefault Value 2 ", t h e passkey for setting u p a BT connection i s F o r security concerns, t h e user can a l s o specify a unique PIN code. 1 Readthe "Enter PIN Code" barcode; 2 Readt h e setting barcodes o f parameters' value i n APPENDIX ONE, i f t h e scanner read t h e setting barcodes i n order, i t means t h e PIN code i s (* )Default V a l u e 1 Default V a l u e 2 E n t e r P I N Code Random P I N Code Refer to APPENDIX I. N o t e : Before the CT30 Scanner connects with the other devices, the user should pre-set the scanner. F o r example: The CT30 Scanner i s t r y i n g t o connect w i t h a h o s t computer, t h e setting operation is according to the following steps: 1. Readt h e "Enter Setup" barcode; 2. Readt h e "Enable SPP" barcode; 3. Readt h e "Default Value 1 " ( P I N code i s 10010); 4. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 28

29 2.3 29

30 The computer will search Bluetooth devices automatically. A few seconds later, y o u will find CT30 i n t h e available devices list, click Next Select Enter t h e device s pairing code, and click N e x t. Input t h e pairing code 10010, a n d click Next 30

31 Y o u can find a prompting a t t h e l o w e r right corner o f your computer desktop, a s following. After around 5 seconds, y o u will hear a beep from CT30, and t h e indicator from red t o blue. T h e n connect successfully. 31

32 Y o u can open a editable textbox (Notepad, w o r d etc.), a n d read t h e barcodes. ( Note: After pairing successfully, open Bluetooth Chat, then you can read the barcodes i n SPP mode.) Now, y o u click Show Bluetooth Devices, y o u can find t h e CT30 i n Devices a n d Printers. 32

33 I f y o u want t o change PIN code o r switch output interface, y o u must remove t h e paired CT30 o n t h e computer first. 33

34 Note: CT30 default mode i s HID Mode, i f y o u want t o u s e SPP mode, just read following barcodes before pairing, other operations is same as HID mode. 34

35 2.4Connect t o PDAv i a BT PDA i s t r y i n g t o connect t o t h e CT30 Scanner (BT SPP). 1. Press t h e Power key a n d t u r n o n t h e CT30 Scanner w i t h correct BT settings, such a s setting u p SPP a s BT t r a n s m i t interface, a n d BT PIN code specified, e t c. 2. F i n d t h e BT i c o n o n PDA, a n d double-click. 3. Click[ A d d NewDevice]. 35

36 4. Choose "CT30",click [Next]. 5. Enter t h e PIN Code. When setting u p a BT connection, i f y o u choose "TheDefault Value 1 ", input 10010; If you choose "The Default Value 2 ", input 40510; if you specified a unique PIN code o n your o w n, input i t. Click [Next]. 6. Click [Finish]. Click[New Transmit Port] in [COM port]. 36

37 7. Choose port number for added device. [COM0] is chosen here. Click [OK]. 37

38 8. Enter serial port application, choose the port number you justset, click [open]. The CT30 Scanner respond w i t h t w o short beeps, a n d t h e indicator i s flashing b l u e (On/Off ratio 20ms:3s), indicating t h e connection between PDA and CT30 i s established successfully. 38

39 2.4.1 One-click Android Connection 1. T u r n o n CT30, read t h e following barcodes continuously E n t e r S e t u p One-click android connection E x i t with S a v e 2. Bluetooth Pairing T u r n o n Bluetooth i n your android device, search CT30 i n available devices, a n d click I t w i l l popup Bluetooth pairing request dialog, input t h e PIN code

40 ClickOK, y o u will hear a beep f r o m CT30, t h a t means pairing successfully, y o u can find paired CT30 on the android device. 40

41 Open a textbox, for example short message, t h e CT30 can read barcodes i n t o t h e textbox. 41

42 2.4.2 One-click iosconnection 1. T u r n o n CT30, a n d read t h e following barcodes continuously E n t e r S e t u p One-click i O S Connection E x i t with S a v e 2.Bluetooth Pairing T u r n o n Bluetooth i n your i o s device, search CT30 i n available devices, a n d click 42

43 I t w i l l popup Bluetooth pairing request dialog, a n d show t h e PIN code F i n d above mentioned numbers i n following barcodes, read t h e m continuously, a n d then read Exit without Save barcode E x i t without S a v e Y o u will hear a beep from CT30 i f connect successfully, a n d i t will show i n t h e paired devices on ios device. 43

44 3. Active or Hide the Input Method During the scanning, you may use the soft keypad if you want to add remark information, you just need double click Power key quickly, it will active the soft keypad. If you double click Power key quickly again, the soft keypad will hide. It is shown as following: 44

45 2.4.3 Connect via BTInput Method 1. Turn on Bluetooth barcode scanner CT30 or CT30 for setup 1 ) Read Enter Setup barcode 2 ) Read Bluetooth Input Method barcode Bluetooth Input Method 3 ) Read Exit w i t h Save barcode 2. Setup CILICO Bluetooth barcode input method Step 1 : T a p Select Input Method 45

46 Select Cilico Bluetooth Input method (support Chinese, English and Japanese) 46

47 Step 2 :Bluetooth Pairing T u r n o n Bluetooth Click Search for devices, and will find CT30/CT30 in available devices 47

48 Clickfor pairing, a n d input t h e PIN code i n following window, t h e n click OK. Y o u w i l l find CT30/ CT30 i n Paired Devices i f pairing successfully. 48

49 Step 3 :Tap Select Bluetooth device ClickCT30/ CT30 i n Bluetooth Paired Device L i s t, i t will connect automatically 49

50 You will hear a beep if connect successfully Step 4:Tap Switch Input Method Select Cilico Bluetooth Input method (support Chinese, English and Japanese), the user can choose according to their requirement 50

51 Step 5:Tap Finish 51

52 Step 6:Open a editable textbox, then can read the barcodes Switch to Chinese input method 52

53 Switch to English input method Switch to Japanese input method 53

54 EDOC ISM31.36.noisimsnarTmuskcehCE-CPU E-CPUelbasiD/elbanE E-CPU noisimsnarTmuskcehCA-CPU tuptuoa-cpu a-cpu1.316.noisimsnartmuskcehc nbsiotrevnoc naeelbasid/elbane nae noisimsnartmuskcehc naeotrevnoc naeelbasid/elbane nae edoc edoc edocicsaluf/dradnats noitacifirevmuskcehc noisimsnartpots/trats edocelbasid/elbane edoc dradnats-52edoc xirtam 52EDOC DEVAELRETNI 52 CODE 3.3 INDUSTRIAL CODE 3.2 CODABAR Chapter 3 SYMBOLOGY SETTINGS In this chapter, a brief on the symbology setting is provided for your reference. Contents 54

55 3.1CODABAR Decide whether o r n o t t o enable Codabar. The CT30 Scanner defaults disable Codabar. Enable Codabar (*)Disable Codabar N o t e : Read the "Disable Codabar" barcode will make the scanner can not read the Codabar barcode. Thus, i f t h e scanner can not read t h e Codabar barcode, please t r y i n g t o read "Enable Codabar" to reset. For example: Enable Codabar. 1. Readt h e "Enter Setup" barcode; 2. Readt h e "Enable Codabar" barcode; 3. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 55

56 3.2CODE 25 INDUSTRIAL25 Decide whether o r not t o enable Industrial 2 5. The CT30 Scanner defaults disable Industrial 2 5. Enable Industrial25 (* )Disable Industrial25 N o t e : Read the "Disable Industrial 25 " barcode will make the scanner can not read the Industrial 2 5 barcode. Thus, i f t h e scanner can n o t read t h e Industrial 2 5 barcode, please t r y i n g t o read "Enable Industrial 2 5 " t o reset. For example: Enable Industrial Readt h e "Enter Setup" barcode. 2. Readthe "Enable Industrial 25 " barcode. 3. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 56

57 3.3CODE 25 INTERLEAVED 25 Decide whether o r n o t t o enable Interleaved 2 5. The CT30 Scanner defaults disable Interleaved 25. Enable Interleaved 25 (*)Disable Interleaved 25 N o t e : Read the "Disable Interleaved 25 " barcode will make the scanner can not read the Interleaved 2 5 barcode. Thus, i f t h e scanner can n o t read t h e Interleaved 2 5 barcode, please trying to read "Enable Interleaved 25 " to reset. For example: Enable Interleaved Readthe "Enter Setup" barcode; 2. Readt h e "Enable Interleaved 2 5 " barcode; 3. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 57

58 3.4CODE 25 MATRIX 25 Decide whether or not to enable Matrix 25. The CT30 Scanner defaults disable Matrix 25 Enable Matrix 25 (*)Disable M a t r i x 25 N o t e : Read t h e "DisableM a t r i x 2 5 " barcode will make t h e scanner can n o t read t h e M a t r i x 2 5 barcode. Thus, i f t h e scanner can not read t h e M a t r i x 2 5 barcode, please t r y i n g t o read "Enable M a t r i x 25" t o reset. For example: Enable Matrix Readt h e "Enter Setup" barcode; 2. Readt h e "Enable M a t r i x 2 5 " barcode; 3. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 58

59 3.5CODE 25-STANDARD 25 Decide whether o r n o t t o enable Standard 2 5. The CT30 Scanner defaults disable Standard 2 5. Enable Standard 25 (* )Disable Standard 25 N o t e : Readt h e "DisableStandard 2 5 " barcode w i l l make t h e scanner can n o t read t h e Standard 2 5 barcode. Thus, i f t h e scanner can n o t read t h e Standard 2 5 barcode, please t r y i n g t o read "Enable Standard 2 5 " t o reset. For Example: Enable Standard Readt h e "Enter Setup" barcode; 2. Readt h e "Enable Standard 2 5 " barcode; 3. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 59

60 3.6CODE Enable/Disable Code 39 Decide whether or not to enable Code 39, The CT30 Scanner defaults disable Code 39. (*)Enable Code 39 Disable Code START/STOP Transmission Decide whether or not to include the start/stop characters in the data being transmitted. *Transmit Code 39 Start/Stop Characters *Do Not Transmit Code 39 Start/Stop Characters For example: DoNotTransmit Code39 Start/Stop Characters. 1. Readt h e "Enter Setup" barcode; 2. Readt h e "Enable Code3 9 " barcode; (If Code3 9 i s disabled, i t i s need t o set); 3. Readt h e "DoNotTransmit Code3 9 Start/Stop Characters" barcode; 4. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 60

61

62 3.6.4 STANDARD/FULL ASCII CODE 39 Decide whether o r n o t t o support Code3 9 F u l l ASCII t h a t includes a l l t h e alphanumeric and special character. The CT30 Scanner defaults full ASCII Code 39. It could disable full ASCII Code3 9 v i a set. Disable Code39 F u l l ASCII * Enable Code39 F u l l ASCII Enter Setup Exit with Save Exit without Save 62

63 3.7CODE 93 Decide whether or not to enable Code 93. The CT30 Scanner defaults disable Code 93. Enable Code93 (*)Disable Code93 N o t e : Readt h e "DisableCode9 3 " barcode will make t h e scanner can n o t read t h e Code 9 3 barcode. Thus, i f t h e scanner can n o t read t h e Code9 3 barcode, please t r y i n g t o read "Enable Code 93 " to reset. For Example: Enable Code Readt h e "Enter Setup" barcode; 2. Readt h e "Enable Code9 3 " barcode; 3. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 63

64 3.8Code 128 Decide whether or not to enable Code 128. The CT30 Scanner defaults enable Code 128. (*)Enable Code128 Disable Code128 N o t e : Read t h e "DisableCode 128" barcode will make t h e scanner can n o t read t h e Code1 2 8 barcode. Thus, i f t h e scanner can not read t h e Code128 barcode, please t r y i n g t o read "Enable Code128" t o reset. For Example: Disable Code Readt h e "Enter Setup" barcode; 2. Readt h e "DisableCode128" barcode; 3. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 64

65 3.9EAN Enable/Disable EAN-8 Decide whether or not to enable EAN-8. The CT30 Scanner defaults enable EAN-8. (*)Enable EAN-8 Disable EAN Convert t o EAN-13 There i s t w o w a y s for EAN-8 t o change, convert t o EAN-13, o r a d d "0"ahead o f EAN-8, a n d t h e EAN-8 I D i s n o t change. Decide whether o r n o t t o convert t o EAN-13, i f EAN-8 convert t o EAN-13, i t will b e read a s same a s EAN-13. I f a d d a "0"ahead o f EAN-8, a n d t h e EAN-8 I D i s n o t change, t h e output I D i s still EAN-8 I D. Convert t o EAN-13 Add "0"ahead a n d I D i s n o t change (* )Donot Convert Enter Setup Exit with Save Exit without Save 65

66

67 3.10 EAN Enable/Disable EAN-13 Decide whether or not to read EAN-13. The CT30 Scanner defaults enable EAN-13. (*)Enable EAN-13 Disable EAN Convert t o ISBN Decide whether o r n o t t o convert t h e EAN-13 t o I S B N. Convert EAN-13 to ISBN * DoNotConvert EAN-13 t o I S B N Enter Setup Exit with Save Exit without Save 67

68

69

70 3.12 UPC-E Enable/Disable UPC-E Decide whether o r n o t t o enable UPC-E. The CT30 Scanner defaults enable UPC-E. (*)Enable UPC-E Disable UPC-E UPC-E Checksum Transmission Decide whether o r n o t t o include t h e checksum character i n t h e d a t a being transmitted. *Transmit UPC-E Checksum DoNotTransmit UPC-E Checksum For example: DoNotTransmit UPC-E Checksum 1. Readt h e "Enter Setup" barcode; 2. Readt h e "Enable UPC-E" barcode; 3. Readt h e "DoNotTransmit UPC-E Checksum" barcode; 4. Readt h e "Exitw i t h Save" barcode. Enter Setup Enter with Save Enter without Save 70

71 3.13 MSI Decide whether or not to enable MSI. The CT30 Scanner defaults disable MSI. Enable M S I (* )Disable M S I N o t e : Read t h e "DisableM S I " barcode will make t h e scanner can n o t read t h e M S I barcode. Thus, i f t h e scanner can n o t read t h e M S I barcode, please t r y i n g t o read "Enable MSI " to reset. For example: Enable MSI. 1. Readt h e "Enter Setup" barcode; 2. Readt h e "Enable M S I " barcode; 3. Readthe "Exitwith Save" barcode. Enter Setup Exit with Save Exit without Save 71

72 3.14 CODE 1 1 Decide whether or not to enable Code 11. The CT30 Scanner defaults disable Code 11. Enable Code11 (* )Disable Code11 N o t e : Readt h e "Disable Code1 1 " barcode will make t h e scanner can not read t h e Code 1 1 barcode. Thus, i f t h e scanner can n o t read t h e Code1 1 barcode, please t r y i n g t o read "Enable Code 11 " to reset. For example: Enable Code Readt h e "Enter Setup" barcode; 2. Readt h e "Enable Code1 1 " barcode; 3. Readt h e "Exitw i t h Save" barcode. Enter Setup Exit with Save Exit without Save 72

73 4.1 Settings APPENDIX I Barcode of Code Suffix 4.2 ID...67 CODE Chapter 4 DEFINING OUTPUT FORMAT Before data transmission to the host or device, you can pre-process the data and decide the format of the data transfer. Contents _Toc

74 4.1 74

75 4.2 75

76 APPENDIX I The setting barcodes of parameters' value