EA-10/14. EA Guidelines on the Calibration of Static Torque Measuring Devices. Publication Reference PURPOSE
|
|
- Philomena Taylor
- 5 years ago
- Views:
Transcription
1 Publication Reference EA-10/14 EA Guidelines on the Calibration of Static Torque Measuring Devices PURPOSE This document has been produced by EA to improve harmonisation in determining the calibration results and uncertainties in torque measurements. It provides information on the calibration procedures for torque measuring devices and gives guidance to calibration laboratories to establish a procedure for the expression of the overall uncertainty of calibration results for torque measuring devices. June rev.00 Page 1 of 0
2 Authorship The publication has been written by EA Committee (Technical Activities), based on a draft of the Task Force «Torque Measurements» of the EA Expert Group «Mechanical Measurements». Official language The text may be translated into other languages as required. The English language version remains the definitive version. Copyright The copyright of this text is held by EA. The text may not be copied for resale. Guidance Publications This document represents a consensus of EA member opinion and preferred practice on how the relevant clauses of the accreditation standards might be applied in the context of the subject matter of this document. The approaches taken are not mandatory and are for the guidance of accreditation bodies and their client laboratories. Nevertheless, the document has been produced as a means of promoting a consistent approach to laboratory accreditation amongst EA member bodies, particularly those participating in the EA Multilateral Agreement. Further information For further information about this publication, contact your national member of EA. Please check our website for up-to-date information June rev.00 Page of 0
3 CONTENTS 1 SCOPE 4 SYMBOLS 4 3 CHARACTERISTICS OF THE TORQUE MEASURING DEVICES 6 4 CALIBRATION OF THE TORQUE MEASURING DEVICE 6 5 DETERMINATION OF THE STANDARD UNCERTAINTY OF MEASUREMENT FOR INCREASING TORQUE 11 6 CALIBRATION CERTIFICATE 14 7 LIST OF REFERENCES 15 APPENDI A 15 APPENDI B 16 APPENDI C 17 APPENDI D 18 APPENDI E 19 June rev.00 Page 3 of 0
4 1 SCOPE 1.01 This guide is generally applicable to torque measuring devices where the torque is obtained by the measurement of the elastic deformation of a body or of a measurand proportional to it. 1.0 The scope of the calibration provided, should be made clear to the customer and recorded on the certificate when calibrating torque systems, i.e. whether all or some of the following are included: clockwise and/or anti-clockwise, incremental and decremental torque The uncertainty of measurement is determined in section 5 1, this should include the parameters of the selected scope This guide applies to the static calibration of torque measuring systems using supported beams or the comparison method with reference transducer and includes an example for calculation of the uncertainty of measurement. A diagram showing an example of the calibration steps and series is given in Annex D The torque measuring device is defined as the complete instrument comprising all parts, from the torque transducer to the indicating device. SYMBOLS For the purpose of this guide, the symbols given in Table 1 shall apply. Table 1: Symbols, units and designations Symbol Designation Unit M nom nominal torque (maximum design torque of the device) N m M A minimum torque value of the measuring range N m M E maximum torque value of the measuring range N m M k applied calibration torque N m I 0 I f I indication of torque measuring device of the zero signal prior to load application in mounting position indication of torque measuring device after load removal in mounting position indication of torque measuring device at torque step with increasing torque (continued) mv/v mv/v mv/v 1 The calculation of measurement uncertainty described in this guidance publication is to be considered as preliminary. It follows EA-4/0 in principle and will after a trial period by the national accreditation bodies, in particular by participation in the EA interlaboratory comparison T, be revised and fully harmonised with EA-4/0 by the relevant EA Expert Group. June rev.00 Page 4 of 0
5 Table 1: (continued) Symbol Designation Unit I indication of torque measuring device at torque step with decreasing torque mv/v S sensitivity (mv/v)/n m indicated value at torque step with increasing torque mv/v a indicated value calculated from the interpolation equation mv/v E mean value of the torque measuring device at maximum of the measuring range mean value of the torque measuring device of increasing steps in different mounting positions mv/v mv/v b repeatability mv/v b reproducibility mv/v f a f q deviation of indication of the torque measuring device from the fitting curve deviation of indication of the torque measuring device with defined scale mv/v N m f 0 residual value at zero signal of the torque measuring device mv/v h reversibility of the torque measuring device mv/v r resolution of the indicating device N m u b uncertainty contribution of repeatability N m w b relative uncertainty contribution of repeatability % u b uncertainty contribution of reproducibility N m w b relative uncertainty contribution of reproducibility % u fa uncertainty contribution of interpolation N m w fa relative uncertainty contribution of interpolation % u r uncertainty contribution of resolution N m w r relative uncertainty contribution of resolution % u tcm uncertainty contribution of the torque calibration machine N m w tcm relative uncertainty contribution of the torque calibration machine u( ) standard uncertainty of measurement mv/v (continued) % June rev.00 Page 5 of 0
6 Table 1: (continued) Symbol Designation Unit w( ) relative standard uncertainty of measurement % u c w c combined standard uncertainty of measurement allowing for systematic errors combined relative standard uncertainty of measurement allowing for systematic errors N m U expanded uncertainty of measurement mv/v W expanded relative uncertainty of measurement % % 3 CHARACTERISTICS OF THE TORQUE MEASURING DEVICES 3.1 Description and identification of the torque measuring device The torque measuring device comprises or consists of the complete set of measuring instruments and other equipment assembled to carry out torque measurements. All components of the torque measuring device (including cables for electrical connection) shall be individually and uniquely identified (for example by the manufacturer s name, the type, four or six conductor circuit or similar, and the serial number). For the torque transducer, the maximum working torque and the measuring end of the transducer should be indicated. 3. Application of the torque The torque transducer and any associated mechanical coupling should be designed and assembled such that both clockwise and anti-clockwise torque can be applied without the significant influence of non-torsional forces, such as bending moments. 4 CALIBRATION OF THE TORQUE MEASURING DEVICE 4.1 General Indicators Where an electrical indicator is replaced with another, both indicators shall have a valid calibration certificate traceable to national standards. The replacement indicator shall have been calibrated over at least the same range of indication as the original indicator. Where the uncertainty of calibration of the replacement indicator differs from the original, the standard uncertainty of measurement should be recalculated. The output indication will be in units depending on the design (e.g. N m, mv/v, V, Hz, mm or others) or in arbitrary units (digits) June rev.00 Page 6 of 0
7 4.1. Overloading test It is recommended that prior to the first calibration, the torque transducer, including its mechanical couplings, is subjected to two overload tests in the course of which the nominal torque is exceeded by 8% to 1% of the nominal torque and this value is maintained for 1 to 1,5 minutes. This should exclude unexpected failure of the torque transducer during application of the calibration load, for example by fracture, resulting in consequential damage to the calibration facility. 4. Resolution of the indicating device 4..1 Analogue scale The thickness of the graduation marks on the scale should be uniform, and the width of the pointer should be approximately equal to the width of a graduation mark: the resolution r of the indicator shall be obtained from the ratio of the width of the pointer to the centre-tocentre distance between adjacent scale marks (scale spacing) - recommended ratios are 1/, 1/5 or 1/10 : spacings not smaller than 1,5 mm are required to estimate a tenth of the scale division. 4.. Digital scale The resolution r is considered to be one increment of the least significant active digit of the numerical indicating device, provided that the indication does not fluctuate by more than one increment when the instrument is unloaded Fluctuation of readings If the reading (with the instrument unloaded) fluctuates by more than the value previously determined for the resolution, the resolution should be deemed to be equal to half the range of fluctuation Resolution The resolution r shall be converted to units of torque using the sensitivity factor S at M E, the maximum torque value of the measuring range Minimum value of the measuring range Taking into consideration the resolution r with which the indicator can be read, the minimum torque M A (minimum value of the measuring range) applied to a torque measuring device should be not less than 0,0 M E (% of the maximum torque value of the measuring range); see also table C.1. June rev.00 Page 7 of 0
8 4.3 Preparation of the calibration Indicating device The indicating device should be adjusted according to the manufacturer s instructions and in accordance with the customer s specifications. Prior to the calibration, it is recommended that the indicating device is subject to a check to ensure it functions correctly and will not invalidate the calibration. All adjustments and, where appropriate, corresponding setting values should be recorded before and after the calibration Temperature stabilisation Prior to calibrating the torque measuring device, it should be stored with the supply power applied in the calibration environment for sufficient time for its temperature to stabilise Transducer zero signal Prior to the installation of the transducer into the calibration equipment, the zero signal of the mechanically unloaded torque transducer should be measured in a specified (vertical) position and recorded Mounting of transducer Failure to apply the calibration torque at the shaft end position stated by the manufacturer, or specified by the customer, may lead to erroneous measurements. The mounting position should be identified. 4.4 Calibration procedure The calibration can be carried out for clockwise and/or anti-clockwise torque. For the purpose of this guideline, the calibration of torque transducers should be carried out as a static procedure by measuring discrete approximately equally spaced torque values (typical of calibration facilities with lever-mass systems) Preloading After installation into the calibration equipment, the torque transducer should be preloaded three times in the direction to be calibrated, applying the maximum torque value M E of the measuring range of the device, and additionally once after each change of the mounting position. The duration of the application of preload should be approximately 30 seconds. After each preload has been removed for approximately 30 seconds, the indicator reading should be recorded. NOTE: The stability of the zero signal may provide an indication of the performance of the device during its calibration. June rev.00 Page 8 of 0
9 4.4. Mounting position The torque transducer should preferably be calibrated in three different mounting positions with the transducer or its mechanical coupling part rotated each time through 10 about the measurement axis. Four relative mounting positions can be used for a square drive (see Annex D). Two incremental calibration series are required at the same mounting position, normally at the start of calibration, for determination of repeatability Range of calibration The recommended number of calibration steps should be a minimum of 5 approximately equally spaced from 0% to 100 % of M E. For the calculation of a fitting curve, a minimum of 5 steps must be taken. When calibration points below 0% of M E are required, calibration steps of 10%, 5%, % of M E should be used Loading conditions The time interval between two successive calibration steps should, if possible, be similar. Recording the measured value may take place only after the indication has stabilised. Indication drift due to creep requires that the time sequence be maintained. Calibration should be carried out at a temperature stable to ±1 C. This temperature should be in the range between 18 C and 8 C (preferably between 0 C and C) and recorded Indicated value The indicated value is defined as the difference between an indication in loaded condition and an indication in unloaded condition. The indication at the beginning of each measurement series should be zeroed, or taken into account by computation during the evaluation following the measurement. NOTE: Recording of non-zeroed values provides additional information about the zero signal behaviour. For torque measuring devices with defined scale (indication in the unit of torque), the indication should be zeroed at the beginning of each measurement series Evaluation of the torque measuring device: Calibration result (Annex E - Worked example of calibration sequence and interpolation of data) Determination of the sensitivity S The sensitivity S shall be calculated according to the following equation: S = M E E (1) June rev.00 Page 9 of 0
10 Determination of mean value The mean value for each torque step shall be calculated according to equation () as the mean value of the measurement results obtained in the increasing series in changed mounting positions: = 1 n Where: j n n ( I j I j,0 ) j= 1 index of selected series number of increasing series in different mounting positions NOTE: The values measured in the 0 position in the second series at increasing torque are not included in the calculation of Determination of repeatability b The repeatability in unchanged mounting position (b ) shall be calculated for each torque step according to the following equation: ' b = Where: 1 1 and are the values measured in unchanged position Determination of reproducibility b The reproducibility in changed mounting position b shall be calculated for each torque step according to the following equation: ( ) j= 1 b = n 1 Where: n n j number of increasing series in different mounting positions NOTE: For the 0 position, the second series at increasing torque is not included in the calculation of b Determination of residual value f 0 at zero torque The zero value shall be recorded prior to and after each measurement series. The zero value shall be read approximately 30 seconds after complete unloading. The residual value of the zero signal shall be calculated according to equation (5): f 0 = max If I 0 () (3) (4) (5) June rev.00 Page 10 of 0
11 Determination of reversibility h The reversibility shall be determined according to equation (6) as the mean of the absolute values of the differences between the values indicated for the series of increasing and decreasing torque series for each torque step: h 1 = k k j= 1 I j I j (6) Where: k number of torque series NOTE: In this section a series is defined as increasing and decreasing torque Determination of the deviation of indication from the fitting curve f a The deviation from the fitting curve shall be determined for each torque step for the indication as a function of the torque using an equation of the 1 st, nd or 3 rd degree without absolute term. The equation used shall be stated in the calibration certificate. The equation shall be calculated as the least squares fit. The deviation from the fitting curve shall be calculated from the following equation (7). f = ( ) a a NOTE: An alternate method consists to calculate the fitting curve and the associated standard uncertainty (u fa ) using the orthogonal polynomial method (Forsythe's algorithm). If this approach is adopted, it should be stated in the certificate. (7) Determination of the deviation of indication f q The deviation of indication shall be determined only for such torque measuring devices where the measured value is directly indicated in the unit of torque and the indicated value is not fitted. It shall be determined from the mean value of the increasing series in changed mounting positions, equation (8): f q = ( ) M k 5 DETERMINATION OF THE STANDARD UNCERTAINTY OF MEASUREMENT FOR INCREASING TORQUE 5.01 The following statements are intended to serve as an example for the calculation of the uncertainty of measurement of a uniform calibration, described in this guide. According to the application of the measuring instrument to be calibrated, it may be useful to deviate from this example or to add further uncertainty components. In such cases, the calculation must be documented. 5.0 The calibration of the torque measuring device is carried out by comparison, using a torque calibration machine with known torque steps, or calibration equipment with a torque reference transducer. (8) June rev.00 Page 11 of 0
12 5.03 The calibration result is the output signal of the torque measuring device and is obtained from the approximate model (9): = ( S + Sb' + δsb + δs fa ) M k where: δ + δ r M k - torque generated by the torque calibration machine with an associated uncertainty u ( M = u k ) δs b' - repeatability with an associated uncertainty u ( δs ) b' = ub' M k tcm δs b - reproducibility with an associated uncertainty u( δs b ) = ub M k S S (9) δs fa - deviation resulting from the fitting curve with an associated uncertainty S u( δs fa ) = u fa M k δ r - observed influence due to instrument resolution with an associated uncertainty u δ ) = S u (two readings for one value indicated) ( r r 5.04 The standard uncertainty u ( ) expressed in units of indication and the relative standard uncertainty w ( ) are obtained by the law of propagation of uncertainty in the approximation of non-correlated variables: u( ) = 5 i= 1 u ( xi) x i (10) u( ) w( ) = 100 (10a) with ( u + u + u + u u ) u + ( ) = S tcm b' b r fa ( w + w + w + w w ) w + ( ) = tcm b' b r fa (11) (11a) 5.05 The example furnishes information on the uncertainty of measurement at the time of calibration. It does not allow for the uncertainty of components long-term stability, or the influence of angular velocity and/or the effects of mechanical couplings used in practice, for example. June rev.00 Page 1 of 0
13 Table : Uncertainty budget - increasing torque only Quantity evaluation of standard uncertainty standard uncertainty in N m relative standard uncertainty in % Repeatability in unchanged mounting position b type A b' u b ' = S b' 100 w b ' = Reproducibility in different mounting positions b type A u b = S b n b 100 w b = n Deviation resulting from fitting curve f a type B with triangular f distribution u = a fa S 6 w fa = fa a Resolution r type B with rectangular r u distribution r = 1 w r = r M k Reference torque type B u tcm wtcm NOTE: For u fa, see also note chapter Calibration of devices with undefined scale The expanded uncertainty of measurement U for each calibration step is calculated from the uncertainty of measurement, equation (10), according to equation (1). The expanded relative uncertainty of measurement W for each calibration step is calculated from the uncertainty of measurement, equation (11a), according to equation (1a). The coverage factor k= applies in both cases. U = k u( ) W = k w( ) (1) (1a) 5. Calibration of devices with a non-adjustable defined scale or where a straight line fit only, can be applied. 5.1 An exceptional case is where the indicator of the torque measuring device is nonadjustable, or has the capability only of fitting a straight line to the data. The values determined for f q or f a are treated as systematic errors whose moduli represent a nondominant part of the uncertainty. In these cases the expanded uncertainty statement at the desired coverage probability of 95% (cf. Ref. No. 3) can only be obtained by equations (16) and (16a), a procedure described in F..4.5 of the Guide to the Expression of Uncertainty in Measurement (cf. Ref. No. 4). June rev.00 Page 13 of 0
14 5. The standard uncertainty u( ) expressed in units of indication and the relative standard uncertainty w ( ) of the random variables is calculated for each calibration step: u + ( ) = S utcm + ub' + ub ur w + ( ) = wtcm + wb' + wb wr (13) (13a) The appropriate formulae for the straight line fit are: u ( ) = fa S c + fa c + w ( ) = u ( ) w ( ) f a - is the deviation from the straight line fit (14) (14a) The appropriate formulae for the defined scale are: fq uc ( ) = + u ( ) S (15) f q wc ( ) = + w ( ) (15a) 5.3 The expanded uncertainty of measurement U or the expanded relative uncertainty of measurement W for each calibration step is calculated from the combined uncertainty of measurement, using equation (16 or 16a), with coverage factor k=: U = k u c ( ) (16) W = k w c ( ) (16a) 6 CALIBRATION CERTIFICATE 6.1 Information to be included on the certificate in addition to that specified in EA-4/01 Where the calibration of a torque measuring device has satisfied the requirements of this guide, the calibration laboratory should draw up a certificate stating the following information, in addition to that shown in guide EA-4/01 (cf. Ref. No. ). a) Identify all the elements of the torque measuring device and its components, including mechanical coupling components to the calibration equipment; b) The method used, identifying whether clockwise and/or anti-clockwise torque, incremental and/or decremental, together with reference to this guide; c) The resolution of the torque measuring device; d) The temperature at which the calibration was performed; June rev.00 Page 14 of 0
15 e) A statement on the expanded uncertainty of measurement and the equation of the fitting curve where applicable; f) Where required, a statement regarding the conformity of the calibration results to a particular classification at the criteria used, for example, see Table C Re-calibration after damage The torque measuring device shall be recalibrated when it has been subjected to an overload higher than that applied in the overloading test (cf. 4.1.), after repair or after inexpert handling, which may have an effect on the uncertainty of measurement. 7 LIST OF REFERENCES APPENDI A Dated references; modifications or revisions to these publications made at a later date are part of this guide only if they have been incorporated. 1 International Vocabulary of Basic and General Terms in Metrology, second edition, 1993, International Organisation for Standardisation (Geneva, Switzerland). EA-4/01: Requirements Concerning Certificates Issued by Accredited Calibration Laboratories, edition 1, November EA-4/0: Expression of the Uncertainty of Measurement in Calibration, edition 1, April Guide to the Expression of Uncertainty in Measurement, first edition, 1993, corrected and reprinted 1995, International Organisation for Standardisation (Geneva, Switzerland). Recommendation for use of calibrated torque measuring devices The calibration is valid only for applications in which the torque measuring device is used in accordance with the conditions in 4.1 to 4.3. Precautions should be taken to prevent the device from being subjected to torque greater than the nominal torque; from being loaded with extraneous forces due to unsuitable coupling components. The calibration, and hence the classification of a torque measuring device whose indication was evaluated as allowing no interpolation, shall be exclusively valid for the discrete values selected. If such an instrument is used at intermediate values, it should be borne in mind that the uncertainty of measurement may be greater than that corresponding to its classification and that the assignment to the class will be invalid. If a torque measuring device is used at a temperature deviating from the calibration temperature as defined in sections 4.3. and 4.4.5, the resulting additional uncertainty of measurement shall be calculated from the data provided by the manufacturer. June rev.00 Page 15 of 0
16 APPENDI B Example of dimensions of torque transducers including couplings for their adaptation to torque calibration facilities In view of the great variety of designs of torque measuring devices and of the types of torsionally rigid couplings recommended for them, the table below offers the calibration laboratories the possibility of substantially reducing the large number of adapters. The proposal allows a design with cylindrical shaft ends, with hubs and as a shaft/hub combination (in each case without feather key and keyway) with shaft frictional clamped couples. Table B.1 Nominal torque M nom Shaft diameter D s Shaft length L s Hub diameter d h Hub length L h N m mm mm mm mm 0 15 h H7 5 >0 to h H7 30 >100 to h H7 40 >500 to h H7 60 >000 to h H7 85 >5000 to h H7 100 If the design with a hub is selected, depending on the material used, the minimum wall thickness shall be according to the table B. below (D h - outside hub diameter) Table B. Material Steel Grey cast iron Aluminium D h /d h 1,5,0,5 June rev.00 Page 16 of 0
17 APPENDI C Classification of the torque measuring device C.1 Principle of classification The range for which the torque measuring device is classified shall be determined by considering each calibration torque one after the other, starting with the maximum torque and decreasing from this to the minimum torque. The classification range ceases at the last torque for which the classification requirements in C. are satisfied. C. Classification criteria C..1 C.. C..3 For the classification, the minimum value of the measuring range M A shall be 0 % of M E, alternatively 40 % of M E for the classes 0,05 and 0,1. For the instruments classified for interpolation, the following criteria shall be taken into consideration: relative repeatability in unchanged mounting position, relative reproducibility in different mounting positions, relative deviation of indication or of fitting curve, relative residual value at zero torque, relative reversibility when increasing and decreasing torque is applied, resolution of the indicating device by at the minimum value of the measuring range M A. Table C.1 states the values of these different parameters for the torque measuring device class and the respective expanded relatively uncertainty required for calibration torque. Table C.1 Classification criteria for torque measuring devices Maximum permissible error of the torque measuring device in % Calibration torque M k class relative repeatability b' relative reproducibility b Relative residual value at zero torque f 0 E relative reversibility h relative dev. of indication or of fitting curve f q, f a min. value of torque M A expanded rel. uncertainty of measurement in % W tcm = k w tcm 0,05 0,05 0,050 0,015 0,063 ±0, r 0,010 0,1 0,05 0,10 0,05 0,15 ±0, r 0,00 0, 0,10 0,0 0,050 0,50 ±0, r 0,040 0,5 0,5 0,50 0,15 0,63 ±0,5 400 r 0,10 1 0,5 1,0 0,5 1,5 ±0,5 00 r 0,0 1,0,0 0,50,50 ±1,0 100 r 0,40 5,5 5 1,5 6,5 ±,5 40 r 1,0 June rev.00 Page 17 of 0
18 APPENDI D Examples of calibration sequences The following sketch shows examples for the calibration of torque measuring devices. June rev.00 Page 18 of 0
19 APPENDI E Worked example of calibration sequence and interpolation of data. E.1 Calibration results for clockwise calibration of 50 N m torque transducer with amplifier in mv/v (see example in annex D, fig. D.1) M E unit temperature in C output in last significant digit in mv/v W tcm in % 50 N m 1,8 mv/v 0, ,00 Indication / in unchanged position steps in % steps in N m 1. preload 0. preload 0 3. preload 0 0 serie 1 0 /1 down 0 serie 0 0-0, , , , , , , , , , , , , , , , ,9014 0, , , , , , , , ,135 1, ,5034 1,505 1,5064 1,509 1,509 1,50304 Indication / in changed position steps in % steps in N m preload down preload down 0 0-0, , , , , , ,0464 0, , , , , , , , , , , , ,9197 0,93 0, , , , , , , , , , ,1304 1, , ,5019 1,5044 1,5044 1, , ,50616 June rev.00 Page 19 of 0
20 E. Determination of mean value and uncertainty expanded relative expanded uncertainty U M k uncertainty W in %, k = in mv/v, k = in N m in mv/v (3 rd degree fitting curve) (3 rd degree fitting curve) 0 0, , ,03 0, ,1804 0,01 0, , ,008 0, , ,004 0, , ,003 0, , ,00 0, ,891 0,00 0, , ,00 0,00003 E.3 Determination of the sensitivity S = M E E S = 0, (mv/v)/n m E.4 Determination of repeatability b, reproducibility b, residual value f 0 at zero torque, reversibility h, deviation of indication from the fitting curve f a, resolution r M k b' b f 0 E h f a (3 rd degree) N m % % % % % % ,0018-0,0130 0,0098-0,0738-0,0077 0, ,0065 0,0059-0,0489-0,006 0, ,0043 0,0041-0,0413-0,0003 0, ,000 0,0014-0,0330 0,0006 0, ,0016 0,0009-0,003 0,0003 0, ,0004 0,0004-0,019 0,0000 0, ,0003 0,000-0,006-0,0001 0, ,0004 0,0003-0,0000 0,0000 0,00013 E.5 Determination of the 3rd degree fitting curve a = 3, M +, M - 1, M 3 M a = 3,5795-7, , E.6 Classification of the torque measuring device: class 0,05 in the range 4 N m to 50 N m class 0,1 in the range N m to 50 N m r M k June rev.00 Page 0 of 0
Guidelines on the Calibration of Static Torque Measuring Devices
European Association of National Metrology Institutes Guidelines on the Calibration of Static Torque Measuring Devices EURAMET/cg-14/v.01 Previously EA-10/14 July 2007 Calibration Guide EURAMET/cg-14/v.01
EA-10/13. EA Guidelines on the Calibration of Temperature Block Calibrators. Publication Reference PURPOSE
Publication Reference EA-10/13 EA Guidelines on the Calibration of Temperature Block Calibrators PURPOSE This document been produced by EA to improve the harmonisation in the calibration of temperature
EA Guidelines on the Calibration of Temperature Indicators and Simulators by Electrical Simulation and Measurement
Publication Reference EA-10/11 EA Guidelines on the Calibration of Temperature Indicators and Simulators by Electrical PURPOSE This document has been produced by EA as a means of giving advice for calibrating
PRELIMINARY DRAFT INDIAN STANDARD METHOD FOR CALIBRATION AND CLASSIFICATION OF TORQUE MEASURING DEVICES INCLUDING TORQUE WRENCH TESTER
For BIS Use Only Doc: PGD 34(1203)P PRELIMINARY DRAFT INDIAN STANDARD METHOD FOR CALIBRATION AND CLASSIFICATION OF TORQUE MEASURING DEVICES INCLUDING TORQUE WRENCH TESTER Not to be reproduced without the
Uncertainty of Calibration. Results in Force Measurements
Publication Reference EAL-G Uncertainty of Calibration Results in Force Measurements PURPOSE This document has been produced to improve the harmonization in determination of uncertainties in force measurements.
Calibration of Temperature Block Calibrators
European Association of National Metrology Institutes Calibration of Temperature Block Calibrators EURAMET cg-13 Version 2.0 (03/2011) Previously EA-10/13 Calibration Guide EURAMET cg-13 Version 2.0 (03/2011)
EA 4/02. Expression of the Uncertainty of Measurement in Calibration. Publication Reference
EAEA Publication Reference EA 4/0 Expression of the Uncertainty of Measurement in Calibration PURPOSE The purpose of this document is to harmonise evaluation of uncertainty of measurement within EA, to
OA03 UNCERTAINTY OF MEASUREMENT IN CHEMICAL TESTING IN ACCORDANCE WITH THE STANDARD SIST EN ISO/IEC Table of contents
UNCERTAINTY OF MEASUREMENT IN CHEMICAL TESTING IN ACCORDANCE WITH THE STANDARD SIST EN ISO/IEC 17025 Table of contents 1 GENERAL... 2 2 THE STANDARD SIST EN ISO/IEC 17025... 2 3 SA'S POLICY IN IMPLEMENTING
EDITION 1 OCTOBER 1997 EA-10/09 PAGE 1 OF
European cooperation for Accreditation of Laboratories Publication Reference EAL-G32 Measurement and Generation of Small AC Voltages with Inductive Voltage Dividers PURPOSE This document has been produced
ISO 376 Calibration Uncertainty C. Ferrero
ISO 376 Calibration Uncertainty C. Ferrero For instruments classified for interpolation, the calibration uncertainty is the uncertainty associated with using the interpolation equation to calculate a single
MEASUREMENT UNCERTAINTY OF ROTATING TORQUE TRANSDUCERS WHEN USED IN PARTIAL LOAD RANGES
XVIII IMEKO WORLD CONGRESS Metrology for a Sustainable Development September, 17, 006, Rio de Janeiro, Brazil MEASUREMENT UNCERTAINTY OF ROTATING TORQUE TRANSDUCERS WHEN USED IN PARTIAL LOAD RANGES Georg
Version 4.0 (09/2017) Version 3.0 (02/2015) Version 2.0 (03/2011) Version 1.0 (07/2007) EURAMET e.v. Bundesallee 100 D Braunschweig Germany
Guidelines on the Calibration of Temperature Block Calibrators Authorship and Imprint This document was developed by the EURAMET e.v., Technical Committee for Thermometry. Authors: Yves Hermier (LNE-INM,
EA-10/17. EA Guidelines on the Calibration of Electromechanical Manometers. Publication Reference
EA-10/17 EA Guidance on the Calibration of Electromechanical Manometers Publication Reference EA-10/17 EA Guidelines on the Calibration of Electromechanical Manometers PURPOSE This document has been developed
Morehouse. Edward Lane, Morehouse Instrument Company 1742 Sixth Ave York, PA PH: web: sales:
Morehouse 1 Morehouse Edward Lane, Morehouse Instrument Company 1742 Sixth Ave York, PA 17403 PH: 717-843-0081 web: www.mhforce.com sales: edlane@mhforce.com 2 This presentation will cover the calibration
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 8426 Second edition 2008-02-01 Hydraulic fluid power Positive displacement pumps and motors Determination of derived capacity Transmissions hydrauliques Pompes et moteurs volumétriques
ISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 7500-1 Third edition 2004-08-15 Metallic materials Verification of static uniaxial testing machines Part 1: Tension/compression testing machines Verification and calibration
Introduction to the evaluation of uncertainty
Manual of Codes of Practice for the Determination of Uncertainties in Mechanical Tests on Metallic Materials SECTION 1 Introduction to the evaluation of uncertainty F A Kandil National Physical Laboratory
Metallic materials Brinell hardness test. Part 3: Calibration of reference blocks
INTERNATIONAL STANDARD ISO 6506-3 Third edition 2014-10-01 Metallic materials Brinell hardness test Part 3: Calibration of reference blocks Matériaux métalliques Essai de dureté Brinell Partie 3: Étalonnage
An Introduction to the Differences Between the Two Most Recognized Force Standards
An Introduction to the Differences Between the Two Most Recognized Force Standards Morehouse Instrument Company Introduction Morehouse has been performing both ASTM E74 and ISO 376 calibrations for more
Project PAJ2 Dynamic Performance of Adhesively Bonded Joints. Report No. 3 August Proposed Draft for the Revision of ISO
NPL Report CMMT(A)81 Project PAJ2 Dynamic Performance of Adhesively Bonded Joints Report No. 3 August 1997 Proposed Draft for the Revision of ISO 11003-2 Adhesives - Determination of Shear Behaviour of
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO Second edition
INTERNATIONAL STANDARD ISO 17123-4 Second edition 2012-06-01 Optics and optical instruments Field procedures for testing geodetic and surveying instruments Part 4: Electro-optical distance meters (EDM
Technical Protocol of the CIPM Key Comparison CCAUV.V-K5
Technical Protocol of the CIPM Key Comparison CCAUV.V-K5 2017-03-06 revised 2018-02-13 (changed schedule) Task and Purpose of the Comparison According to the rules set up by the CIPM MRA the consultative
Calibration Traceability Guidelines
Calibration Traceability Guidelines Check the website of accrediting bodies for the accredited laboratories individual scope of accreditation www.a2la.org ts.nist.gov/standards/accreditation/index.cfm
SVENSK STANDARD SS-EN ISO
SVENSK STANDARD SS-EN ISO 376:2005 Fastställd 2005-02-04 Utgåva 2 Metalliska material Kalibrering av kraftmätdon avsedda för kontroll av maskiner för enaxlig provning (ISO 376:2004) Metallic materials
Metallic materials Brinell hardness test. Part 2: Verification and calibration of testing machines
INTERNATIONAL STANDARD ISO 6506-2 Third edition 2014-10-01 Metallic materials Brinell hardness test Part 2: Verification and calibration of testing machines Matériaux métalliques Essai de dureté Brinell
T e c h n i c a l L e x i c o n
T e c h n i c a l L e x i c o n T e r m s f r o m F o r c e a n d t o r q u e m e a s u r e m e n t t e c h n o l o g y a n d G T M d a t a s h e e t s Technisches Lexikon (eng.) 16/10/14 Introduction
INTERNATIONAL STANDARD
IEC 61788-6 INTERNATIONAL STANDARD Edition 2.0 2008-01 Superconductivity Part 6: Mechanical properties measurement Room temperature tensile test of Cu/Nb-Ti composite superconductors IEC 61788-6:2008(E)
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60287-1-3 First edition 2002-05 Electric cables Calculation of the current rating Part 1-3: Current rating equations (100 % load factor) Current sharing between parallel single-core
Guidelines on the Calibration of Automatic Instruments for Weighing Road Vehicles in Motion and Measuring Axle Loads AWICal WIM Guide May 2018
Guidelines on the Calibration of Automatic Instruments for Weighing Road Vehicles in Motion and Measuring Axle Loads AWICal WIM Guide May 2018 Guidelines on the Calibration of Automatic Instruments for
ISO INTERNATIONAL STANDARD. Metallic materials Vickers hardness test Part 3: Calibration of reference blocks
INTERNATIONAL STANDARD ISO 6507-3 Third edition 2005-12-15 Metallic materials Vickers hardness test Part 3: Calibration of reference blocks Matériaux métalliques Essai de dureté Vickers Partie 3: Étalonnage
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO Second edition
INTERNATIONAL STANDARD ISO 6974-1 Second edition 2012-05-15 Natural gas Determination of composition and associated uncertainty by gas chromatography Part 1: General guidelines and calculation of composition
OIML D 28 DOCUMENT. Edition 2004 (E) ORGANISATION INTERNATIONALE INTERNATIONAL ORGANIZATION. Conventional value of the result of weighing in air
INTERNATIONAL DOCUMENT OIML D 28 Edition 2004 (E) Conventional value of the result of weighing in air Valeur conventionnelle du résultat des pesées dans l'air OIML D 28 Edition 2004 (E) ORGANISATION INTERNATIONALE
The Determination of Uncertainties in Bend Tests on Metallic Materials
Manual of Codes of Practice for the Determination of Uncertainties in Mechanical Tests on Metallic Materials Code of Practice No. 09 The Determination of Uncertainties in end Tests on Metallic Materials
Part 5: Total stations
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 17123-5 Third edition 2018-02 Optics and optical instruments Field procedures for testing geodetic and surveying instruments Part 5: Total stations
SVENSK STANDARD SS-EN ISO 376. Metalliska material Kalibrering av kraftmätdon avsedda för kontroll av maskiner för enaxlig provning (ISO 376:1999)
SVENSK STANDARD SS-EN ISO 376 Fastställd 2002-02-01 Utgåva 1 Metalliska material Kalibrering av kraftmätdon avsedda för kontroll av maskiner för enaxlig provning (ISO 376:1999) Metallic materials Calibration
POWER QUALITY MEASUREMENT PROCEDURE. Version 4 October Power-Quality-Oct-2009-Version-4.doc Page 1 / 12
POWER QUALITY MEASUREMENT PROCEDURE Version 4 October 2009 Power-Quality-Oct-2009-Version-4.doc Page 1 / 12 MEASNET 2009 Copyright all rights reserved This publication may not be reproduced or utilized
Comparison of measurement uncertainty budgets for calibration of sound calibrators: Euromet project 576
NPL REPORT CMAM 73 Comparison of measurement uncertainty budgets for calibration of sound calibrators: Euromet project 576 Peter Hanes October 2001 The National Physical Laboratory is operated on behalf
OIML R 50-3 RECOMMENDATION. Edition 2014 (E) ORGANISATION INTERNATIONALE INTERNATIONAL ORGANIZATION
INTERNATIONAL RECOMMENDATION OIML R 50-3 Edition 2014 (E) Continuous totalizing automatic weighing instruments (belt weighers). Part 3: Test report format Instruments de pesage totalisateurs continus à
Document No: TR 12 Issue No: 1
ESTIMATION OF THE UNCERTAINTY OF MEASUREMENT BY CALIBRATION LABORATORIES AND SPECIFICATION OF CALIBRATION AND MEASUREMENT CAPABILITY ON SCHEDULES OF ACCREDITATION Prepared by: SADCAS Technical Manage Approved
OIML R 51-2 RECOMMENDATION. Edition 2006 (E) ORGANISATION INTERNATIONALE INTERNATIONAL ORGANIZATION. Automatic catchweighing instruments
INTERNATIONAL RECOMMENDATION OIML R 51-2 Edition 2006 (E) Automatic catchweighing instruments Part 2: Test report format Instruments de pesage trieurs-étiqueteurs à fonctionnement automatique Partie 2:
APPENDIX G EVALUATION OF MEASUREMENT UNCERTAINTY
APPENDIX G EVALUATION OF MEASUREMENT UNCERTAINTY Table of Contents 1. SCOPE... 2 2. REFERENCES... 2 3. TERMS AND DEFINITIONS... 2 4. BACKGROUND... 4 5. EVALUATION OF MEASUREMENT UNCERTAINTY POLICY... 5
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 61788-6 First edition 2000-12 Superconductivity Part 6: Mechanical properties measurement Room temperature tensile test of Cu/Nb-Ti composite superconductors Supraconductivité
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60076-10 First edition 2001-05 Power transformers Part 10: Determination of sound levels Transformateurs de puissance Partie 10: Détermination des niveaux de bruit IEC 2001 Copyright
This document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 18437-1 First edition 2012-08-15 Mechanical vibration and shock Characterization of the dynamic mechanical properties of visco-elastic materials Part 1: Principles and guidelines
R SANAS Page 1 of 7
ESTIMATION OF THE UNCERTAINTY OF MEASUREMENT BY CALIBRATION LABORATORIES AND SPECIFICATION OF CALIBRATION AND MEASUREMENT CAPABILITY ON SCHEDULES OF ACCREDITATION Approved By: Chief Executive Officer:
Mechanical vibration Rotor balancing. Part 2: Vocabulary. Vibrations mécaniques Équilibrage des rotors Partie 2: Vocabulaire. First edition
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 21940-2 First edition 2017-05 Mechanical vibration Rotor balancing Part 2: Vocabulary Vibrations mécaniques Équilibrage des rotors Partie 2: Vocabulaire
Determination of particle size distribution Single particle light interaction methods. Part 4:
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 21501-4 Second edition 2018-05 Determination of particle size distribution Single particle light interaction methods Part 4: Light scattering airborne
SAMM POLICY 5 (SP5) POLICY ON MEASUREMENT UNCERTAINTY REQUIREMENTS FOR SAMM TESTING LABORATORIES Issue 2, 28 February 2007 (Amd. 1, 11 August 2014)
SKIM AKREDITASI MAKMAL MALAYSIA (SAMM) LABORATORY ACCREDITATION SCHEME OF MALAYSIA SAMM POLICY 5 (SP5) POLICY ON MEASUREMENT UNCERTAINTY REQUIREMENTS FOR SAMM TESTING LABORATORIES Issue 2, 28 February
APPENDIX G ESTIMATION OF UNCERTAINTY OF MEASUREMENT
APPENDIX G ESTIMATION OF UNCERTAINTY OF MEASUREMENT Table of Contents 1. SCOPE... 2 2. REFERENCES... 2 3. TERMS AND DEFINITIONS... 2 4. BACKGROUND... 4 5. ESTIMATION OF UNCERTAINTY OF MEASUREMENT POLICY...
UNCERTAINTY ANALYSIS FOR LABORATORY ACCREDITATION. Peter B. Crisp. Fluke Precision Measurement Ltd, 52 Hurricane Way, Norwich, UK
UNCERTAINTY ANALYSIS FOR LABORATORY ACCREDITATION Peter B. Crisp Fluke Precision Measurement Ltd, 5 Hurricane Way, Norwich, UK Introduction NAMAS Accredited laboratories are required to follow recommended
ISO INTERNATIONAL STANDARD. Metallic materials Brinell hardness test Part 2: Verification and calibration of testing machines
INTERNATIONAL STANDARD ISO 6506-2 Second edition 2005-12-15 Metallic materials Brinell hardness test Part 2: Verification and calibration of testing machines Matériaux métalliques Essai de dureté Brinell
Withdrawn at December 31, Guideline DKD-R 5-7. Calibration of Climatic Chambers DEUTSCHER KALIBRIERDIENST
DEUTSCHER KALIBRIERDIENST Guideline DKD-R 5-7 Calibration of Climatic Chambers Edition 07/2004 English translation 02/2009 Page 1 of 31 Published by the Accreditation Body of the Deutscher Kalibrierdienst
UNCERTAINTY SCOPE OF THE FORCE CALIBRATION MACHINES. A. Sawla Physikalisch-Technische Bundesanstalt Bundesallee 100, D Braunschweig, Germany
Measurement - Supports Science - Improves Technology - Protects Environment... and Provides Employment - No and in the Future Vienna, AUSTRIA, 000, September 5-8 UNCERTAINTY SCOPE OF THE FORCE CALIBRATION
INVESTIGATION OF TRANSFER STANDARDS IN THE HIGHEST RANGE UP TO 50 MN WITHIN EMRP PROJECT SIB 63 Falk Tegtmeier 1, Michael Wagner 2, Rolf Kumme 3
XXI IMEKO World Congress Measurement in Research and Industry August 30 September 4, 2015, Prague, Czech Republic INVESTIGATION OF TRANSFER STANDARDS IN THE HIGHEST RANGE UP TO 50 MN WITHIN EMRP PROJECT
ISO INTERNATIONAL STANDARD. Mechanical vibration and shock Coupling forces at the man-machine interface for hand-transmitted vibration
INTERNATIONAL STANDARD ISO 15230 First edition 2007-07-01 Mechanical vibration and shock Coupling forces at the man-machine interface for hand-transmitted vibration Vibrations et chocs mécaniques Forces
JAB NOTE4. ESTIMATION OF MEASUREMENT UNCERTAINTY (Electrical Testing / High Power Testing) Japan Accreditation Board (JAB)
JAB NOTE4 ESTIMATION OF MEASUREMENT UNCERTAINTY (Electrical Testing / High Power Testing) nd edition: January 5 01 1 st edition: March 5 00 Japan Accreditation Board (JAB) Initial edition: 00-0-5 1/ nd
A61-02 CALA Guidance on Traceability Revision 1.2 October 15, 2012
Revision 1.2 October 15, 2012 PAGE II TABLE OF CONTENTS TABLE OF CONTENTS... 1 GUIDANCE...2 1.0 Introduction... 2 2.0 Uncertainty and Traceability... 2 3.0 Need for Traceability... 3 3.1 What does traceability
ISO 3741 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 3741 Fourth edition 2010-10-01 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Precision methods for reverberation
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60758 Edition 5.0 2016-05 Synthetic quartz crystal Specifications and guidelines for use INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 31.140 ISBN 978-2-8322-3395-5 Warning!
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60758 Third edition 2004-12 Synthetic quartz crystal Specifications and guide to the use IEC 2004 Copyright - all rights reserved No part of this publication may be reproduced
T20WN. Data Sheet. Torque transducers. Special features. Installation example with bellows couplings. B en
T20WN Torque transducers Data Sheet Special features - Nominal (rated) torques 0.1 N m, 0.2 N m, 0. N m, 1 N m, 2 N m, N m, 10 N m, 20 N m, 0 N m, 100 N m, 200 N m - Accuracy class: 0.2 - Contactless transmission
UNCERTAINTY IN TORQUE CALIBRATION USING VERTICAL TORQUE AXIS ARRANGEMENT AND SYMMETRICAL TWO FORCE MEASUREMENT
UNCERTAINTY IN TORQUE CALIBRATION USING VERTICAL TORQUE AXIS ARRANGEMENT AND SYMMETRICAL TWO FORCE MEASUREMENT Dieter Kenzler 1, Jörg Oblasser 2, Andreas Subaric-Leitis 2 and Christian Ullner 2 1 ) SCHATZ
ISO 844 INTERNATIONAL STANDARD. Rigid cellular plastics Determination of compression properties
INTERNATIONAL STANDARD ISO 844 Fifth edition 2007-04-15 Rigid cellular plastics Determination of compression properties Plastiques alvéolaires rigides Détermination des caractéristiques de compression
Metallic materials Knoop hardness test. Part 1: Test method. Matériaux métalliques Essai de dureté Knoop Partie 1: Méthode d'essai
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 4545-1 Second edition 2017-12 Metallic materials Knoop hardness test Part 1: Test method Matériaux métalliques Essai de dureté Knoop Partie 1:
Specific Accreditation Guidance. Infrastructure and Asset Integrity. Measurement Uncertainty in Geotechnical Testing
Specific Accreditation Guidance Infrastructure and Asset Integrity Measurement Uncertainty in Geotechnical Testing January 2018 Copyright National Association of Testing Authorities, Australia 2018 This
OIML R 141 RECOMMENDATION. Edition 2008 (E) ORGANISATION INTERNATIONALE INTERNATIONAL ORGANIZATION
INTERNATIONAL RECOMMENDATION OIML R 141 Edition 2008 (E) Procedure for calibration and verification of the main characteristics of thermographic instruments Procédure pour l'étalonnage et la vérification
Part 2: Methods for special reverberation test rooms
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 3743-2 Second edition 2018-02 Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small,
Guidelines on the Calibration of Non-Automatic Weighing Instruments
European Association of National Metrology Institutes Guidelines on the Calibration of Non-Automatic Weighing Instruments EURAMET/cg-18/v.01 Previously EA-10/18 July 007 Calibration Guide EURAMET/cg-18/v.01
MEASUREMENT UNCERTAINTY PREPARED FOR ENAO ASSESSOR CALIBRATION COURSE OCTOBER/NOVEMBER Prepared by MJ Mc Nerney for ENAO Assessor Calibration
MEASUREMENT PREPARED FOR ENAO ASSESSOR CALIBRATION COURSE UNCERTAINTY OCTOBER/NOVEMBER 2012 Prepared by for ENAO Assessor Calibration B SCOPE Introduction House Rules Overview 17025 & 15189 MU Approaches
GUIDELINE FOR HAND HELD SHEAR VANE TEST
GUIDELINE FOR HAND HELD SHEAR VANE TEST NZ GEOTECHNICAL SOCIETY INC August 2001 CONTENTS Page 1.0 Introduction 2 2.0 Background 2 3.0 Recommended Practice 3 4.0 Undrained Shear Strength 3 5.0 Particular
Revision of CMM performance specifications
Educational Articles: Article nr. 3 Revision of CMM performance specifications Premise The working group (WG) Specifications is one of several working groups of ia.cmm, the International Association of
European Association of National Metrology Institutes
European Association of National Metrology Institutes EURAMET GUIDELINES ON TEMPERATURE: Extrapolation of SPRT calibrations below the triple point of argon, 83.8058 K, and traceability in baths of liquid
IS INTERNATIONAL STANDARD. Natural gas - Guidelines to traceability in analysis
INTERNATIONAL STANDARD IS0 14111 First edition 1997-03-15 Natural gas - Guidelines to traceability in analysis Gaz na turel - Lignes directrices pour la tracabilit6 en analyse Reference number IS0 14111
ISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10848-3 First edition 2006-04-01 Acoustics Laboratory measurement of the flanking transmission of airborne and impact sound between adjoining rooms Part 3: Application to light
ISO/TS TECHNICAL SPECIFICATION. Water quality Guidance on analytical quality control for chemical and physicochemical water analysis
TECHNICAL SPECIFICATION ISO/TS 13530 First edition 2009-03-15 Water quality Guidance on analytical quality control for chemical and physicochemical water analysis Qualité de l'eau Lignes directrices pour
Modelling of a dynamic torque calibration device and determination of model parameters
ACTA IMEKO June 2014, Volume 3, Number 2, 14 18 www.imeko.org Modelling of a dynamic torque calibration device and determination of model parameters Leonard Klaus, Thomas Bruns, Michael Kobusch Physikalisch-Technische
ISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 16063-15 First edition 2006-08-01 Methods for the calibration of vibration and shock transducers Part 15: Primary angular vibration calibration by laser interferometry Méthodes
Disclosure to Promote the Right To Information
इ टरन ट म नक Disclosure to Promote the Right To Information Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information
After publication, this Indian Standard will supersede the following Indian Standards:
For Comments Only Doc: PGD 26(1110)W Draft Indian Standard SPECIFICATION FOR NON-AUTOMATIC WEIGHING INSTRUMENTS PART 1 TERMINOLOGY AND DEFINITIONS ICS No. 01.040.17; 17.100 Not to be reproduced without
ISO INTERNATIONAL STANDARD. Rolling bearings Linear motion rolling bearings Part 2: Static load ratings
INTERNATIONAL STANDARD ISO 14728-2 First edition 2004-06-01 Rolling bearings Linear motion rolling bearings Part 2: Static load ratings Roulements Roulements à mouvement linéaire Partie 2: Charges statiques
< Final report > Report on the APMP.M.F-S1 supplementary comparison for 2 MN Force
< Final report > Report on the APMP.M.F-S1 supplementary comparison for 2 MN Force Kazunaga Ueda*, Toshiyuki Hayashi*, Hiroshi Maejima*, Rolf Kumme**, Dirk Röske**, Mark Seidel** * National Metrology of
METHODS TO CONFIRM THE MEASUREMENT CAPABILITY OF THE FORCE STANDARD MACHINES AFTER REINSTALLATION
IMEKO 22 nd TC3, 12 th TC5 and 3 rd TC22 International Conferences 3 to 5 February, 2014, Cape Town, Republic of South Africa METHODS TO CONFIRM THE MEASUREMENT CAPABILITY OF THE FORCE STANDARD MACHINES
A guide to expression of uncertainty of measurements QA4EO-QAEO-GEN-DQK-006
A guide to expression of uncertainty of measurements QA4EO-QAEO-GEN-DQK-006 A guide to expression of uncertainty of measurements Author: E-mail: Nigel Fox Nigel.Fox@npl.co.uk Editor: E-mail: Marie-Claire
Technical Protocol of the Bilateral Comparison in Primary Angular Vibration Calibration CCAUV.V-S1
Technical Protocol of the Bilateral Comparison in Primary Angular Vibration Calibration CCAUV.V-S1 Updated at 12-December-2012 Task and Purpose of the Comparison According to the rules set up by the CIPM
ISO INTERNATIONAL STANDARD. Surface chemical analysis X-ray photoelectron spectroscopy Repeatability and constancy of intensity scale
INTERNATIONAL STANDARD ISO 24237 First edition 2005-06-01 Surface chemical analysis X-ray photoelectron spectroscopy Repeatability and constancy of intensity scale Analyse chimique des surfaces Spectroscopie
OIML R RECOMMENDATION. Edition 2006 (E) ORGANISATION INTERNATIONALE INTERNATIONAL ORGANIZATION. Instruments for measuring the areas of leathers
INTERNATIONAL RECOMMENDATION OIML R 136-2 Edition 2006 (E) Instruments for measuring the areas of leathers Part 2: Test Report Format Instruments pour la mesure de la surface des cuirs Partie 2 : Format
THE NEW 1.1 MN m TORQUE STANDARD MACHINE OF THE PTB BRAUNSCHWEIG/GERMANY
THE NEW 1.1 MN m TORQUE STANDARD MACHINE OF THE PTB BRAUNSCHWEIG/GERMANY D. Peschel 1, D. Mauersberger 1, D. Schwind 2, U. Kolwinski 2 1 Solid mechanics department, PTB, Germany 2 Gassmann Theiss Messtechnik
Glossary Innovative Measurement Solutions
Glossary GLOSSARY OF TERMS FOR TRANSDUCERS, LOAD CELLS AND WEIGH MODULES This purpose of this document is to provide a comprehensive, alphabetical list of terms and definitions commonly employed in the
ISO INTERNATIONAL STANDARD. Metallic materials Knoop hardness test Part 1: Test method
INTERNATIONAL STANDARD ISO 4545-1 First edition 2005-11-15 Metallic materials Knoop hardness test Part 1: Test method Matériaux métalliques Essai de dureté Knoop Partie 1: Méthode d'essai Reference number
ISO Radiological protection Sealed radioactive sources General requirements and classification
INTERNATIONAL STANDARD ISO 2919 Third edition 2012-02-15 Radiological protection Sealed radioactive sources General requirements and classification Radioprotection Sources radioactives scellées Exigences
Investigation of Piezoelectric Force Measuring Devices in Force Calibration and Force. Standard Machines
Proceedings of the 17 th International Conference on Force, Mass, Torque and Pressure Measurements, Investigation of Piezoelectric Force Measuring Devices in Force Calibration and Force Standard Machines
Final Report on the Torque Key Comparison CCM.T-K2 Measurand Torque: 0 kn m, 10 kn m, 20 kn m Dirk Röske 1), Koji Ogushi 2)
Final Report on the Torque Key Comparison CCM.T-K Measurand Torque: kn m, 1 kn m, kn m Dirk Röske 1), Koji Ogushi ) 1) ) Dirk RÖSKE Physikalisch-Technische Bundesanstalt Department 1. Solid Mechanics orking
SOUTH AFRICAN NATIONAL STANDARD. Modulus of elasticity and modulus of rupture in static bending of fibreboards Amdt 1
ISBN 978-0-66-956-7 Any reference to SABS SM 1015 is deemed to be a reference to this standard (Government Notice No. 17 of 8 November 00) SOUTH AFRICAN NATIONAL STANDARD Modulus of elasticity and modulus
M3003 EDITION 2 JANUARY 2007
M3003 EDITION 2 JANUARY 2007 The Expression of Uncertainty and Confidence in Measurement JH 2007 CONTENTS SECTION PAGE 1 Introduction 2 2 Overview 4 3 More detail 10 4 Type A evaluation of standard uncertainty
VK2 volume flow controller Overview
New option with sound attenuator Maintenance-free VK2 volume flow controller that operates without an auxiliary power supply, for ventilation and air conditioning systems. Adjustable on site. Outstanding
MOY/SCMI/36 SPECIFICATION OF ACCURACY FOR A PRECISION CLINOMETER
Centre for Basic, Thermal and Length Metrology National Physical Laboratory MOY/SCMI/36 SPECIFICATION OF ACCURACY FOR A PRECISION CLINOMETER A Watts Precision Clinometer fitted with a circular glass scale
ANNEXE 8. Technical protocols for the interlaboratory comparisons
ANNEXE 8 Technical protocols for the interlaboratory comparisons TECHNICAL PROTOCOL FOR BILATERAL COMPARISON (Magnitude of the complex charge sensitivity of accelerometers) EURAMET.AUV.V-S1 1. INTRODUCTION
ISO INTERNATIONAL STANDARD. Rolling bearings Thermal speed rating Calculation and coefficients
INTERNATIONAL STANDARD ISO 1512 First edition 200-12-01 Rolling bearings Thermal speed rating Calculation and coefficients Roulements Vitesse de référence thermique Calculs et facteurs de correction Reference
ISO INTERNATIONAL STANDARD. Acoustics Acoustic insulation for pipes, valves and flanges
INTERNATIONAL STANDARD ISO 15665 First edition 2003-08-15 Acoustics Acoustic insulation for pipes, valves and flanges Acoustique Isolation acoustique des tuyaux, clapets et brides Reference number ISO
INTERNATIONAL OIML R 61-2 RECOMMENDATION
INTERNATIONAL OIML R 61-2 RECOMMENDATION Edition 2004 (E) Automatic gravimetric filling instruments Part 2: Test report format Doseuses pondérales à fonctionnement automatique Partie 2: Format du rapport