Towards selective test protocols for accelerated in situ degradation of PEM electrolysis cell components
|
|
- Johnathan Grant
- 5 years ago
- Views:
Transcription
1 Towards selective test protocols for accelerated in situ degradation of PEM electrolysis cell components 1 st International Conference on Electrolysis - Copenhagen Thomas Lickert, Claudia Schwarz, Patricia Gese, Arne Fallisch, Malte Schlüter, Nicolas Höfling and Tom Smolinka Fraunhofer Institute for Solar Energy Systems ISE Copenhagen/DK,
2 AGENDA Introduction: Fraunhofer ISE and the division Hydrogen Technologies Why do we want to have accelerated stress tests (ASTs) ISE approach on AST development what are the stressors? First results from our projects Measurement equipment (test bench, test cell and materials) Voltage vs time & Vi curves (challenges on IR correction) Benefits of electrochemical impedance spectroscopy (EIS) Conclusion
3 Fraunhofer Institute for Solar Energy Systems ISE At a Glance Photovoltaics Solar Thermal Technology Fraunhofer ISE Director: Staff: ca. 1.2 Budget 216: 81 Mio. Established: 1981 Prof. H-M. Henning and A. Bett Building Energy Technology Hydrogen Technology Energy System Technology
4 Business Area Hydrogen Technologies Research topics Department Thermochemical Processes Thermochemical H 2 generation from hydrocarbons Synthesis of H 2 and CO 2 to liquid energy carriers/fuels (PtL) Catalytic evaporation of liquid hydrocarbons Department Chemical Energy Storage (Dr. Tom Smolinka) Hydrogen generation by PEM water electrolysis Energy storage in H 2 systems and redox flow batteries Power-to-Gas: Interconnection of the power and gas grid Department Fuel Cell Systems Scientific characterisation of fuel cell components Degradation research (load profile, various climates) Customer specific, self-sufficient PEM systems up to 2 kw
5 Electrolyzer hardware why do we want to have ASTs PEM-EL cells are electrochemically quite stable (required today) Degradation occurs slowly Standard materials (thick Nafion PEM) are typically used Investigation of the degredation on standard materials = cost intensive Cheaper and more efficient stacks are required in the future New materials are needed unkown degr. behavior Fast screening of these new materials how do we approch AST development?
6 Development of AST protocols Fraunhofer ISE approach Operating conditions: Stressors to be defined Current density Temperature H 2 O contamination Dynamic operation
7 Development of AST protocols Fraunhofer ISE approach Measurements 4 measurements T = 8 C using different profiles (1st measurement currently in repetition) 2x steady-state (No. 1 & 2) 2x alternating profile (No. 3 & 4) Current density [A/cm²] T = 8 C p = barg 3 A/cm² 5min 15min 5min 2.5 A/cm².3 A/cm² Test 1 Test 2 Test 3 Test A/cm² Time [min]
8 Electrolysis hardware Test bench Semi-automated test bench Process control (non automated) H 2 O circulation on both sides Temperature up to 8 C, p = barg and H 2 O circul. of.3 l/min 1 l/min Electronics (automated): Ivium multi channel potentiostat + 1 A Ivium booster (controlled by Iviumsoft) Impedance spectroscopy up i DC = 4 A/cm² (f = 1 mhz 1 khz)
9 Electrolysis hardware Test cell and materials Test cell: Polymer frame cell with Au coated flow channels (+ Au RE) Pressurized measurements up to 5 barg 23 cm² active area (1 cm² RE) Investigation of anodic and cathodic half cell potentials Cell materials: PTL: Ti powder sinter; 1 mm, 4 % porosity (Mott corp., USA) MEA: commercial; N117 based
10 Development of AST protocols Measurement results: U(t) cell i = 3 A/cm² 2.2 C1 2. C2 C3 C6 C4 C5 cell voltage [V] test bench shut down IR-corrected cell voltage Voltage decay happening in the beginning cell i = 2.5 & 3.5 A/cm² C1 C2 C6 C Block fill up water tank cell i =.3 A/cm² C4 C3 C6 C IR-corrected cell voltage cell voltage [V] C2 336 fill up water tank 2. C1 Block B6 24 measurement time [h] measurement time [h] cell voltage [V] C4 C3 IR corrected voltage 1.6 V(t) mostly nonohmic Information content limited test bench shut down fill up water tank 2.2 cell voltage [V] V(t) profile depends on current density fill up water tank C 1 C4 C3 C6 C5 C7 1.9 cell voltage IR-corrected cell voltage C measurement time [h] Block Block measurement time [h] Block
11 Development of AST protocols Measurement results: Vi curves Vi(t) changes rather small Information content limited without IRcorrection Possible MTL observed cell voltage [V] 2.4 U(i) between blocks of i = 3 A/cm² C 1 C 2 C 3 C 4 C 5 C current density [A/cm²] U(i) between blocks of i =.3 A/cm² cell voltage [V] U(i) between blocks of i = 2.5 & 3.5 A/cm² 3 C 1 C 2 C 3 C 4 C 5 C current density [A/cm²] U(i) between blocks of i =.3 & 3 A/cm² cell voltage [V] C 1 C 2 C 3 C 4 C 5 C 6 cell voltage [V] Block 7 Block current density [A/cm²] current density [A/cm²]
12 Development of AST protocols Benefits of electrochemical impedance spectroscopy (1) IR correction (example: test 4) HFR needed DC signal superimposed by AC f = 1 khz Distinction between ohmic and non-ohmic contributions Ω i η η η cell voltage [V] Block 7 Block Current density Time R current density [A/cm²]
13 Development of AST protocols Benefits of Electrochemical Impedance Spectroscopy (1) Issues with IR correction by fixed f (example: test 4) Low low i (cable behavior) HFR measurement faulty Extrapolation of HFR to low i necessary Extraction of kinetic parameters (i, tafel parameters) faulty 1 khz not necessarily = HFR intercept with Re axis 1.2 differs from test to test HFR [m *cm²] IR-corrected cell voltage [V] current density [A/cm²] (IR corrected) (IR corrected) (IR corrected) (IR corrected) (IR corrected) (IR corrected) Block 7 (IR corrected) Block 8 (IR corrected) (IR corrected) log (current density) [A/cm²] 4
14 Development of AST protocols Benefits of Electrochemical Impedance Spectroscopy (1) Issues with IR correction by fixed f (example: test 4) Low low i (cable behavior) HFR measurement faulty Extrapolation of HFR to low i necessary Extraction of kinetic parameters (i, tafel parameters) faulty 1 khz not neccessarily = HFR intercept with Re-axis differs from test to test HFR [m *cm²] current density [A/cm²]
15 Development of AST protocols Measurement results: EIS Im{Z} [m cm²] -3-2 I DC = 2 A/cm² I AC = 5 % I DC T = 8 C p = 1 bar Q =.3 l/min -1 1st peak ~ 8Hz Re{Z} [m cm²] 1st peak ~ 8Hz Im{Z} [m cm²] I DC = 2 A/cm² I AC = 5 % I DC T = 8 C p = 1 bar Q =.3 l/min Peak ~ 6Hz 2nd Peak ~ 2Hz Re{Z} [m cm²] 3 Im{Z} [m cm²] I DC = 2 A/cm² I AC = 5 % I DC 8 C; 1 bar Peak ~ 8Hz 2 Im{Z} [m ] I DC = 2 A/cm² I AC = 5 % I DC T = 8 C p = 1 bar Q =.3 l/min (2 A/cm²) After (2 A/cm²) After (2A/cm²) After (2A/cm²) After (2A/cm²) After (2A/cm²) After (2A/cm²) After Block 7 (2A/cm²) Im{Z} Re{Z} [m cm²] Re{Z} [m ]
16 Development of AST protocols Benefits of Electrochemical Impedance Spectroscopy (2) Vi curve is limited in its information content Changes in the range of mfew mv (for 34 h degr. Test) Vi-curve might show MTL here Distinction between low and high frequency processes possible with EIS Compare Vi curve and 2 A/cm² (Test 3) cell voltage [V] Im{Z} [m cm²] U(i) between blocks of i = 2.5 & 3.5 A/cm² 3 C 1 C 2 C 3 C 4 C 5 C current density [A/cm²] I DC = 2 A/cm² I AC = 5 % I DC T = 8 C p = 1 bar Q =.3 l/min Peak ~ 6Hz 2nd Peak ~ 2Hz Re{Z} [m cm²] 3
17 Development of AST protocols Benefits of Electrochemical Impedance Spectroscopy (3) Main benefits Distinction between low and fast processes (not possible from Vi curve) MTL (slow process) and kinetics (fast process) can be observed more clearly Possible to extract kinetic parameters without measurements at very low current density (equivalent circuit) By capacitive behavior exchange current density i (using an equivalent circuit) Most beneficial characterisation tool for AST development
18 Development of AST protocols conclusion Status of AST development Conditions must be harsher in terms of current density dynamics Many measurements must be conducted Current density dependency rather small (for 34 h tests) Behavior at shut down need to be investigated On/off cycles to be tested
19 Acknowledgement Projects: FCH-JU: Novel and BMBF: PowerMEE FCH-JU: Novel Novel materials and system designs for low cost, efficient and durable PEM electrolysers Novel: No BMBF (germ. Gov.): PowerMEE Lifetime and performance improvement of polymer electrolyte membrane electrolyzers with high performance membrane electrode assemblies. PowerMEE:
20 Thank you for your Attention! Fotos Fraunhofer Institute for Solar Energy Systems ISE Thomas Lickert, Claudia Schwarz, Patricia Gese, Arne Fallisch, Malte Schlüter, Nicolas Höfling and Tom Smolinka
Batteries (Electrochemical Power Sources)
Batteries (Electrochemical Power Sources) 1. Primary (single-discharge) batteries. => finite quantity of the reactants 2. Secondary or rechargeable batteries => regeneration of the original reactants by
More informationGeneral Energy PEM Membrane Tests
General Energy PEM Membrane Tests Date 11/03/2016 Author Annette Mosdale, R&D PaxiTech Client Ms. Sophia Hu General Energy Room 404, 321 Talent Building, No. 1009 East Tianyuan Road Nanjing 210000 PR China
More informationDevelopment of Bifunctional Electrodes for Closed-loop Fuel Cell Applications. Pfaffenwaldring 6, Stuttgart, Germany
Development of Bifunctional Electrodes for Closed-loop Fuel Cell Applications S. Altmann a,b, T. Kaz b, K. A. Friedrich a,b a Institute of Thermodynamics and Thermal Engineering, University Stuttgart,
More informationExperimental Characterization Methodology for the Identification of Voltage Losses of PEMFC: Applied to an Open Cathode Stack
Experimental Characterization Methodology for the Identification of Voltage Losses of PEMFC: Applied to an Open Cathode Stack A. Husar *, S. Strahl, J. Riera Institut de Robòtica i Informàtica Industrial
More informationState-Space Modeling of Electrochemical Processes. Michel Prestat
State-Space Modeling of Electrochemical Processes Who uses up my battery power? Michel Prestat ETH-Zürich Institute for Nonmetallic Materials Head: Prof. L.J. Gauckler Outline Electrochemistry Electrochemical
More informationAn Introduction to Electrochemical Impedance Spectroscopy (EIS)
An Introduction to Electrochemical Impedance Spectroscopy (EIS) Dr. Robert S Rodgers, Ph.D. PO Box 7561 Princeton, NJ 08543 Delivered at June 18, 2009 Meeting of ACS Princeton Local Section Outline A Little
More informationMikaël Cugnet, Issam Baghdadi, and Marion Perrin OCTOBER 10, Excerpt from the Proceedings of the 2012 COMSOL Conference in Milan
Mikaël Cugnet, Issam Baghdadi, and Marion Perrin OCTOBER 0, 202 Comsol Conference Europe 202, Milan, CEA Italy 0 AVRIL 202 PAGE Excerpt from the Proceedings of the 202 COMSOL Conference in Milan SUMMARY
More informationProperties of novel anion selective material with DABCO functional groups for alkaline water electrolysis
Properties of novel anion selective material with DABCO functional groups for alkaline water electrolysis Jaromír Hnát, Jan Žitka, Martin Ďurovič, Martin Paidar, Karel Bouzek Department of Inorganic Technology
More informationNumerical modelling of membrane degradation in PEM water electrolyzer: Influence of the temperature and current density
Numerical modelling of membrane degradation in PEM water electrolyzer: Influence of the temperature and current density M. Chandesris, V. Médeau, N. Guillet, S. Chelghoum, D. Thoby, F. Fouda-Onana Univ.
More informationGraphene-based Electrodes for Electrochemical Energy Conversion
Graphene-based Electrodes for Electrochemical Energy Conversion September 23, 2014 AVS North California Chapter Prof. Min Hwan Lee School of Engineering Graphene for electrochemical devices Properties
More informationHalf-Cell, Steady-State Flow-Battery Experiments. Robert M. Darling and Mike L. Perry
Half-Cell, Steady-State Flow-Battery Experiments Robert M. Darling and Mike L. Perry United Technologies Research Center, East Hartford, Connecticut, 06108, USA An experimental approach designed to separately
More informationJune 16 th, Charles Monroe, Levi Thompson, Alice Sleightholme, and Aaron Shinkle University of Michigan Department of Chemical Engineering
Non Aqueous Vanadium Redox Flow Batteries June 16 th, 2010 Charles Monroe, Levi Thompson, Alice Sleightholme, and Aaron Shinkle University of Michigan Department of Chemical Engineering Christian Doetsch,
More informationModelling fuel cells in start-up and reactant starvation conditions
Modelling fuel cells in start-up and reactant starvation conditions Brian Wetton Radu Bradean Keith Promislow Jean St Pierre Mathematics Department University of British Columbia www.math.ubc.ca/ wetton
More informationELECTROCHEMICAL COMPRESSION OF PRODUCT HYDROGEN FROM PEM ELECTROLYZER STACK
ELECTROCHEMICAL COMPRESSION OF PRODUCT HYDROGEN FROM PEM ELECTROLYZER STACK N.V. Dale 1,*, C. Y. Biaku 1, M. D. Mann 1, H. Salehfar 2, A. J. Peters 2 Abstract The low volumetric energy density of hydrogen
More informationHydrogen Evolution on Ni Electrode during Synthetic Tap Water Electrolysis
Hydrogen Evolution on Ni Electrode during Synthetic Tap Water Electrolysis Y. Petrov, F. de Bruijn, J.-P. Schosger, Z. Stoynov This document appeared in Detlef Stolten, Thomas Grube (Eds.): 18th World
More informationDiagnosis of PEMFC operation using EIS
Diagnosis of PEMFC operation using EIS Electrical Research Institute Hydrogen and Fuel Cells Group Félix Loyola, Ulises Cano-Castillo ucano@iie.org.mx International Symposium on DIAGNOSTIC TOOLS FOR FUEL
More informationCapacity fade studies of Lithium Ion cells
Capacity fade studies of Lithium Ion cells by Branko N. Popov, P.Ramadass, Bala S. Haran, Ralph E. White Center for Electrochemical Engineering, Department of Chemical Engineering, University of South
More informationActivity. Modeling the Fuel Cell Reaction. Overview. Advance Preparation. Background Information
4 Activity 1-2 class sessions Modeling the uel Cell Reaction 2011 Regents of the University of California Overview n order to understand the chemistry of fuel cells, students are introduced to oxidation-reduction
More informationProf. Mario L. Ferrari
Sustainable Energy Mod.1: Fuel Cells & Distributed Generation Systems Dr. Ing. Mario L. Ferrari Thermochemical Power Group (TPG) - DiMSET University of Genoa, Italy Lesson II Lesson II: fuel cells (electrochemistry)
More informationGraphene-based Air Electrodes for Solid Oxide Electrochemical Cells
Graphene-based Air Electrodes for Solid Oxide Electrochemical Cells April 18, 2014 Prof. Min Hwan Lee School of Engineering Graphene for electrochemical devices Properties Applications Electron conducting
More informationANALYTICAL INVESTIGATION AND IMPROVEMENT OF PERFORMANCE OF A PROTON EXCHANGE MEMBRANE (PEM) FUEL CELL IN MOBILE APPLICATIONS
Int. J. of Applied Mechanics and Engineering, 015, vol.0, No., pp.319-38 DOI: 10.1515/ijame-015-001 ANALYTICAL INVESTIGATION AND IMPROVEMENT OF PERFORMANCE OF A PROTON EXCHANGE MEMBRANE (PEM) FUEL CELL
More informationCatalyst Development Needs
Catalyst Development Needs (presented at the NSF Workshop in Washington DC, Nov. 14-15, 2001) Hubert Gasteiger 1) Mark Mathias 2) Susan Yan 3) Cathode Catalysts cathode related MEA performance losses cathode
More informationNUMERICAL ANALYSIS ON 36cm 2 PEM FUEL CELL FOR PERFORMANCE ENHANCEMENT
NUMERICAL ANALYSIS ON 36cm 2 PEM FUEL CELL FOR PERFORMANCE ENHANCEMENT Lakshminarayanan V 1, Karthikeyan P 2, D. S. Kiran Kumar 1 and SMK Dhilip Kumar 1 1 Department of Mechanical Engineering, KGiSL Institute
More informationStudy of current distribution and oxygen diffusion in the fuel cell cathode catalyst layer through electrochemical impedance spectroscopy
Loughborough University Institutional Repository Study of current distribution and oxygen diffusion in the fuel cell cathode catalyst layer through electrochemical impedance spectroscopy This item was
More informationDirect Energy Conversion: Fuel Cells
Direct Energy Conversion: Fuel Cells References and Sources: Direct Energy Conversion by Stanley W. Angrist, Allyn and Beacon, 1982. Fuel Cell Systems, Explained by James Larminie and Andrew Dicks, Wiley,
More informationCharacterisation of a proton exchange membrane electrolyser using electrochemical impedance spectroscopy
Characterisation of a proton exchange membrane electrolyser using electrochemical impedance spectroscopy A dissertation presented to The School of Electrical, Electronic and Computer Engineering North-West
More informationModeling, simulation and characterization of atomic force microscopy measurements for ionic transport and impedance in PEM fuel cells
Modeling, simulation and characterization of atomic force microscopy measurements for ionic transport and impedance in PEM fuel cells Peter M. Pinsky David M. Barnett Yongxing Shen Department of Mechanical
More informationUnraveling Fuel Cell Electrical Measurements
A G R E A T E R M E A S U R E O F C O N F I D E N C E Unraveling Fuel Cell Electrical Measurements James Niemann, Keithley Instruments, Inc. ducting, catalyzed anode and cathode electrodes. See Figure
More informationi i ne. (1) i The potential difference, which is always defined to be the potential of the electrode minus the potential of the electrolyte, is ln( a
We re going to calculate the open circuit voltage of two types of electrochemical system: polymer electrolyte membrane (PEM) fuel cells and lead-acid batteries. To do this, we re going to make use of two
More informationV.A.11 Development of Ultra-Low Platinum Alloy Cathode Catalysts for Polymer Electrolyte Membrane Fuel Cells
V.A.11 Development of Ultra-Low Platinum Alloy Cathode Catalysts for Polymer Electrolyte Membrane Fuel Cells Branko N. Popov University of South Carolina (USC) 301 Main Street Columbia, SC 29208 Phone:
More informationFacile and Gram-scale Synthesis of Metal-free Catalysts: Toward Realistic Applications for Fuel Cells
Supplementary Information Facile and Gram-scale Synthesis of Metal-free Catalysts: Toward Realistic Applications for Fuel Cells Ok-Hee Kim 1, Yong-Hun Cho 2, Dong Young Chung 3,4, Minjeong Kim 3,4, Ji
More informationPolymer graphite composite anodes for Li-ion batteries
Polymer graphite composite anodes for Li-ion batteries Basker Veeraraghavan, Bala Haran, Ralph White and Branko Popov University of South Carolina, Columbia, SC 29208 Plamen Atanassov University of New
More informationALUMINUM ELECTROLYTIC CAPACITORS Capacitor Life
1 of 8 5/12/2008 10:23 PM Home About Us Products Contact Us Info Other Links Aluminum Part # Search ALUMINUM ELECTROLYTIC CAPACITORS Capacitor Life Table of Contents Capacitor Life The life of aluminum
More informationElectrochemical Impedance Spectroscopy (EIS)
CHEM465/865, 24-3, Lecture 26-28, 19 th Nov., 24 Please, note the following error in the notes lecture19+2 (Hydrodynamic electrodes and Microelectrodes: on page two, 3 rd line, the correct expression for
More informationFUEL CELLS in energy technology (4)
Fuel Cells 1 FUEL CELLS in energy technology (4) Werner Schindler Department of Physics Nonequilibrium Chemical Physics TU Munich summer term 213 Fuel Cells 2 Nernst equation and its application to fuel
More informationDISCLAIMER. Portions of this document may be illegible in electronic image products. Images are produced from the best available original document.
; i i : L4 0 t DSCLAMER Portions of this document may be illegible in electronic image products. mages are produced from the best available original document. EVALUATON OF THE HUMDFCATON REQTJREMENTS OF
More informationSupporting Information for: Polyaniline-Modified Pt Catalyst for Improved Electrochemical Reduction of CO 2
Supporting Information for: Polyaniline-Modified Pt Catalyst for Improved Electrochemical Reduction of CO 2 David N. Abram, a Kendra P. Kuhl b, Etosha R. Cave c, Thomas F. Jaramillo a adepartment of Chemical
More informationElectrochemical Cells Homework Unit 11 - Topic 4
Electrochemical Cell Vocabulary Electrochemical Cells Homework Unit 11 - Topic 4 Electrode Anode Voltaic Cell Oxidation Electrolytic Cell Cathode Salt Bridge Reduction Half Reaction Refer to Table J: For
More informationElectrolytes for Fuel Cells
Electrolytes for Fuel Cells Tom Zawodzinski Materials Science and Technology Division Los Alamos National Laboratory Air-Breather Fuel Cell Stack Systems Laptop Demo DCH/Enable Prototype Small Battery
More informationFernando O. Raineri. Office Hours: MWF 9:30-10:30 AM Room 519 Tue. 3:00-5:00 CLC (lobby).
Fernando O. Raineri Office Hours: MWF 9:30-10:30 AM Room 519 Tue. 3:00-5:00 CLC (lobby). P1) What is the reduction potential of the hydrogen electrode g bar H O aq Pt(s) H,1 2 3 when the aqueous solution
More informationModeling of Liquid Water Distribution at Cathode Gas Flow Channels in Proton Exchange Membrane Fuel Cell - PEMFC
Modeling of Liquid Water Distribution at Cathode Gas Flow Channels in Proton Exchange Membrane Fuel Cell - PEMFC Sandro Skoda 1*, Eric Robalinho 2, André L. R. Paulino 1, Edgar F. Cunha 1, Marcelo Linardi
More informationDemystifying Transmission Lines: What are They? Why are They Useful?
Demystifying Transmission Lines: What are They? Why are They Useful? Purpose of This Note This application note discusses theory and practice of transmission lines. It outlines the necessity of transmission
More informationBasic overall reaction for hydrogen powering
Fuel Cell Basics Basic overall reaction for hydrogen powering 2H 2 + O 2 2H 2 O Hydrogen produces electrons, protons, heat and water PEMFC Anode reaction: H 2 2H + + 2e Cathode reaction: (½)O 2 + 2H +
More informationIntroduction Fuel Cells Repetition
Introduction Fuel Cells Repetition Fuel cell applications PEMFC PowerCell AB, (S1-S3) PEMFC,1-100 kw Toyota Mirai a Fuel Cell Car A look inside The hydrogen tank 1. Inside Layer of polymer closest to the
More informationJoint Sino-German Project GZ 205 (101/5) New composite DMFC anode with PEDOT as mixed conductor and catalyst support. Report
Joint Sino-German Project GZ 25 (11/5) New composite DMFC anode with PEDOT as mixed conductor and catalyst support Report 15. 4. 24 14. 4. 26 K. Jüttner, R. Dittmeyer, L. Li, J.-F. Drillet DECHEMA e.v.,
More informationHydrogen production by electrolysis. Ann Cornell, Department of Chemical Engineering, KTH
Hydrogen production by electrolysis Ann Cornell, Department of Chemical Engineering, KTH amco@kth.se Sources for hydrogen International Energy Agency. Technology Roadmap Hydrogen and Fuel Cells, 2015
More informationMASTER OF APPLIED SCIENCE
Algorithm Development for Electrochemical Impedance Spectroscopy Diagnostics in PEM Fuel Cells By Ruth Anne Latham BSME, Lake Superior State University, 2001 A Thesis Submitted in Partial Fulfillment of
More informationDETERMINING THE OPERATING CONDITIONS OF ALL-VANADIUM REDOX FLOW BATTERY
Proceedings of the Asian Conference on Thermal Sciences 2017, 1st ACTS March 26-30, 2017, Jeju Island, Korea ACTS-P00650 DETERMINING THE OPERATING CONDITIONS OF ALL-VANADIUM REDOX FLOW BATTERY Jungmyoung
More informationWir schaffen Wissen heute für morgen
Wir schaffen Wissen heute für morgen Paul Scherrer Institut L. Gubler, A. Albert, Y. Buchmüller, O. Nibel, L. Bonorand Radiation Grafting: Tailored Ion-conducting Membranes for Electrochemical Applications
More informationStaircase Potentio Electrochemical Impedance Spectroscopy and automatic successive ZFit analysis
Application note #18 Staircase Potentio Electrochemical Impedance Spectroscopy and automatic successive ZFit analysis I- Introduction It is sometimes useful to automate measurements. With EC-Lab and EC-Lab
More informationIntroduction to EIS (Electrochemical Impedance Spectroscopy) with EC- Lab /EC-Lab Express
Introduction to EIS (Electrochemical Impedance Spectroscopy) with EC- Lab /EC-Lab Express N. Murer, J.-P. Diard 1 /23 OBJECTIVES Understand what is performed during an impedance measurement. Understand
More informationFuel Cell Activities in MME Waterloo
Fuel Cell Activities in MME Waterloo Xianguo Li and Roydon Fraser Fuel Cells and Green Energy Research Group Department of Mechanical & Mechatronics Engineering University of Waterloo, Waterloo, Ontario,
More informationSupporting Information. Electrocatalytic polysulfide-traps for controlling redox shuttle process of Li-S battery
Supporting Information Electrocatalytic polysulfide-traps for controlling redox shuttle process of Li-S battery Hesham Al Salem, Ganguli Babu, Chitturi V. Rao and Leela Mohana Reddy Arava * Department
More informationElectrocatalysis: Experimental Techniques and Case Studies
Electrocatalysis: Experimental Techniques and Case Studies 1) Introduction (what is electrochemistry?) Electric double layer Electrode potential 2) How to measure electrochemical reactions? Cyclic voltammetry
More informationLecture 4. Conductance sensors. ChemFET. Electrochemical Impedance Spectroscopy. py Practical consideration for electrochemical biosensors.
Lecture 4 Conductance sensors. ChemFET. Electrochemical Impedance Spectroscopy. py Practical consideration for electrochemical biosensors. Conductivity I V = I R=, L - conductance L= κa/, l Λ= κ /[ C]
More informationIntroductory Lecture: Principle and Applications of Fuel Cells (Methanol/Air as Example)
3 rd LAMNET Workshop Brazil -4 December 00 3 rd LAMNET Workshop Brazil 00 Introductory Lecture: Principle and Applications of Fuel Cells (Methanol/Air as Example) Prof. Dr. Wolf Vielstich University of
More informationGrant agreement No SOCTESQA
Solid Oxide Cell and Stack Testing, Safety and Quality Assurance Collaborative Project - FCH JU GRANT AGREEMENT N 621245 THEME [SP1-JTI-FCH.2013.5.4] Start date: 01.05.2014 Duration: 36 months Project
More informationVariable capacitor energy harvesting based on polymer dielectric and composite electrode
2.8.215 Variable capacitor energy harvesting based on polymer dielectric and composite electrode Robert Hahn 1*, Yuja Yang 1, Uwe Maaß 1, Leopold Georgi 2, Jörg Bauer 1, and K.- D. Lang 2 1 Fraunhofer
More informationElectrochemical methods : Fundamentals and Applications
Electrochemical methods : Fundamentals and Applications Lecture Note 7 May 19, 2014 Kwang Kim Yonsei University kbkim@yonsei.ac.kr 39 8 7 34 53 Y O N Se I 88.91 16.00 14.01 78.96 126.9 Electrochemical
More information(name) Electrochemical Energy Systems, Spring 2014, M. Z. Bazant. Final Exam
10.626 Electrochemical Energy Systems, Spring 2014, M. Z. Bazant Final Exam Instructions. This is a three-hour closed book exam. You are allowed to have five doublesided pages of personal notes during
More informationMODELLING A 500W POLYMER ELECTROLYTE MEMBRANE FUEL CELL
University of Technology, Sydney Faculty of Engineering MODELLING A 500W POLYMER ELECTROLYTE MEMBRANE FUEL CELL by Andrew Richard Balkin Student Number: 97087439 Major: Electrical Engineering Supervisor:
More informationAnalysis of the Catalyst Layer of Polymer Electrolyte Fuel Cells
33 Research Report Analysis of the Catalyst Layer of Polymer Electrolyte Fuel Cells Takahisa Suzuki Hajime Murata Tatsuya Hatanaka Yu Morimoto Comprehensive techniques for diagnosing the catalyst layer
More informationLithium-ion Batteries Based on Vertically-Aligned Carbon Nanotubes and Ionic Liquid
Electronic Supplementary Information Lithium-ion Batteries Based on Vertically-Aligned Carbon Nanotubes and Ionic Liquid Electrolytes Wen Lu, * Adam Goering, Liangti Qu, and Liming Dai * 1. Synthesis of
More informationproduce water. Figure 1. Basic Diagram of a PEMFC. [1]
Effects of Graphene Oxide on Proton Exchange Membrane Fuel Cells Henry Ho, Jesse Matsuda, Mailun Yang, Likun Wang, Miriam Rafailovich Materials Science and Chemical Engineering Department, Stony Brook,
More informationPerformance Analysis of a Two phase Non-isothermal PEM Fuel Cell
Performance Analysis of a Two phase Non-isothermal PEM Fuel Cell A. H. Sadoughi 1 and A. Asnaghi 2 and M. J. Kermani 3 1, 2 Ms Student of Mechanical Engineering, Sharif University of Technology Tehran,
More informationWork Package 1 Batteries
Work Package 1 Batteries FUTURE/VESI Seminar 14 th Jan 2015, London Dr Gregory Offer*, Dr Edmund Noon, Billy Wu, Sam Cooper, Vladimir Yufit, Farid Tariq, Marie-Therese Srbik, Monica Marinescu, Ricardo
More informationand constant current operations in capacitive deionization
Energy consumption analysis of constant voltage and constant current operations in capacitive deionization Supporting information Yatian Qu, a,b Patrick G. Campbell, b Lei Gu, c Jennifer M. Knipe, b Ella
More informationEstimation of approximate activation energy loss and mass transfer coefficient from a polarization curve of a polymer electrolyte fuel cell
Korean J. Chem. Eng., 29(9), 1158-1162 (2012) DOI: 10.1007/s11814-012-0006-3 INVITED REVIEW PAPER Estimation of approximate activation energy loss and mass transfer coefficient from a polarization curve
More informationBasic overall reaction for hydrogen powering
Fuel Cell Basics Basic overall reaction for hydrogen powering 2H 2 + O 2 2H 2 O Hydrogen produces electrons, protons, heat and water PEMFC Anode reaction: H 2 2H + + 2e Cathode reaction: (½)O 2 + 2H +
More informationDMFC Models and Applications - A Literature Survey, Part I
Proceedings of the 2014 International Conference on Industrial Engineering and Operations Management Bali, Indonesia, January 7 9, 2014 DMFC Models and Applications - A Literature Survey, Part I S. Patrabansh,
More informationTransient carbon monoxide poisoning of a polymer electrolyte fuel cell operating on diluted hydrogen feed
Electrochimica Acta 49 (2004) 2333 2341 Transient carbon monoxide poisoning of a polymer electrolyte fuel cell operating on diluted hydrogen feed Krishan Kumar Bhatia, Chao-Yang Wang Electrochemical Engine
More informationPGM-free OER Catalysts for Proton Exchange Membrane Electrolyzer
PGM-free OER Catalysts for Proton Exchange Membrane Electrolyzer Di-Jia Liu, Argonne National Laboratory November 14, 2017 HydroGEN Kick-Off Meeting, National Renewable Energy Laboratory HydroGEN Kick-Off
More informationELECTROCHEMICAL CELLS NAME ROW PD
4-26-12 NAME ROW PD (1) Which statement describes the redox reaction that occurs when an object is electroplated? The diagram below shows the electrolysis of fused KCl. A) It is spontaneous and requires
More informationFrano Barbir Pictorial Resume. energy partners
Frano Barbir Pictorial Resume energy partners Diagnostic(s) noun the art or practice of diagnosis Diagnosis noun Investigation or analysis of the cause or nature of a condition, situation or problem Diagnostics
More informationCare of Computer-Controlled Potentiostats
Care of Computer-Controlled Potentiostats What is a Potentiostat? Potentiostat An electronic instrument that measures and controls the voltage difference between a Working Electrode and a Reference Electrode.
More informationAllen J. Bard, Netzahualcóyotl Arroyo-Currás (Netz Arroyo), Jinho Chang, Brent Bennett. Department of Chemistry and Center for Electrochemistry
REDOX Allen J. Bard, Netzahualcóyotl Arroyo-Currás (Netz Arroyo), Jinho Chang, Brent Bennett Department of Chemistry and Center for Electrochemistry The University of Texas at Austin 1 What is a redox
More informationUNIVERSITY OF TORONTO. FINAL EXAM, APRIL 28, hours. EXAMINER D.W. Kirk,
Page 1 of 11 PRINT FIRST NAME LAST NAME STUDENT NUMBER UNIVERSITY OF TORONTO FINAL EXAM, APRIL 28, 2017 2.5 hours CHE 469F - FUEL CELLS and ELECTROCHEMICAL SYSTEMS Do all questions. The marks add up to
More informationPhotovoltaic Characterizations: Polarization and Mott Schottky plot
Application note #4 Photovoltaic Characterizations: Polarization and Mott Schottky plot I- Introduction With the greenhouse effect and the increase of the price of the energy, new ways to produce energy
More informationElectrolysis System CHLORINSITU V (PLUS)
Output of 100 3.500 g/h of ultra-pure active chlorine (hypochlorous acid) Electrolysis systems of the type CHLORINSITU V generate ultrapure active chlorine using the unique vacuum method with the membrane
More informationUnderstanding Impedance of Li-Ion Batteries with Battery Design Studio
Understanding Impedance of Li-Ion Batteries with Battery Design Studio Robert Spotnitz Battery Consultant Thursday July 6, 2017 16:40-17:10 Understanding Impedance Li-Ion Batteries with Battery Design
More informationVI. EIS STUDIES LEAD NANOPOWDER
VI. EIS STUDIES LEAD NANOPOWDER 74 26. EIS Studies of Pb nanospheres Impedance (valid for both DC and AC), a complex resistance occurs when current flows through a circuit (composed of various resistors,
More informationAppendix A Electric Vehicle PEM Fuel Cell Stack Parameters
Appendix A Electric Vehicle PEM Fuel Cell Stack Parameters A.1 Return Manifold Polynomial Fitting Table A.1 Return manifold polynomial fitting Parameter Value Return manifold parameter p 0 0.001248 kg/s
More informationCorrelating Hydrogen Evolution Reaction Activity in Alkaline Electrolyte to Hydrogen Binding Energy on Monometallic Surfaces
Supplemental Materials for Correlating Hydrogen Evolution Reaction Activity in Alkaline Electrolyte to Hydrogen Binding Energy on Monometallic Surfaces Wenchao Sheng, a MyatNoeZin Myint, a Jingguang G.
More informationPOLITECNICO DI MILANO
POLITECNICO DI MILANO Facoltà di Ingegneria Industriale POLITECNICO DI MILANO Department Corso di Laurea of Energy in Doctoral Ingegneria Program in Energy and Nuclear Science and Technology DMFC MODELING:
More informationPEMFC on line diagnosis via acoustic emission measurements. B. Legros, P.-X. Thivel*, Y Bultel, R.P. Nogueira
PEMFC on line diagnosis via acoustic emission measurements B. Legros, P.-X. Thivel*, Y Bultel, R.P. Nogueira Laboratory of electrochemistry and physico-chemistry of materials and interfaces (LEPMI) Science
More informationAdvanced Analytical Chemistry Lecture 12. Chem 4631
Advanced Analytical Chemistry Lecture 12 Chem 4631 What is a fuel cell? An electro-chemical energy conversion device A factory that takes fuel as input and produces electricity as output. O 2 (g) H 2 (g)
More informationHighly Durable MEA for PEMFC Under High Temperature and Low Humidity Conditions. Eiji Endoh a. Yokohama, JAPAN
10.1149/1.2356118, copyright The Electrochemical Society Highly Durable MEA for PEMFC Under High Temperature and Low Humidity Conditions Eiji Endoh a a Research Center, Asahi Glass Co., Ltd. 1150 Hazawacho,
More informationFigure 1. Contact mode AFM (A) and the corresponding scanning Kelvin probe image (B) of Pt-TiN surface.
Synopsis Synopsis of the thesis entitled Titanium Nitride-ased Electrode Materials for Oxidation of Small Molecules: pplications in Electrochemical Energy Systems submitted by Muhammed Musthafa O. T under
More informationSupplemental Information. Carbon Monoxide Gas Diffusion Electrolysis. that Produces Concentrated C 2 Products. with High Single-Pass Conversion
JOUL, Volume 3 Supplemental Information Carbon Monoxide Gas Diffusion Electrolysis that Produces Concentrated C 2 Products with High Single-Pass Conversion Donald S. Ripatti, Thomas R. Veltman, and Matthew
More informationVOLTAGE SINGULARITY CLASSIFICATION FOR FUEL CELL DIAGNOSIS
FRENCH INSTITUTE OF SCIENCE AND TECHNOLOGY FOR TRANSPORT, DEVELOPMENT AND NETWORKS VOLTAGE SINGULARITY CLASSIFICATION FOR FUEL CELL DIAGNOSIS Djedjiga BENOUIOUA IFSTTAR / COSYS / LTN FC LAB Belfort, FRANCE
More informationModeling as a tool for understanding the MEA. Henrik Ekström Utö Summer School, June 22 nd 2010
Modeling as a tool for understanding the MEA Henrik Ekström Utö Summer School, June 22 nd 2010 COMSOL Multiphysics and Electrochemistry Modeling The software is based on the finite element method A number
More informatione - Galvanic Cell 1. Voltage Sources 1.1 Polymer Electrolyte Membrane (PEM) Fuel Cell
Galvanic cells convert different forms of energy (chemical fuel, sunlight, mechanical pressure, etc.) into electrical energy and heat. In this lecture, we are interested in some examples of galvanic cells.
More informationPolyoxometalate Coupled Graphene Oxide-Nafion Composite. Membrane for Fuel Cell Operating at Low Relative Humidity
Electronic Supplementary Material (ESI) for Journal of Materials Chemistry A. This journal is The Royal Society of Chemistry 2015 Electronic Supplementary Information (ESI) Polyoxometalate Coupled Graphene
More informationThe Mechanism of Electropolishing of Nb in Hydrofluoric-Sulfuric Acid (HF+H 2 SO 4 ) Electrolyte
The Mechanism of Electropolishing of Nb in Hydrofluoric-Sulfuric Acid (HF+H 2 SO 4 ) Electrolyte Hui Tian *+, Charles E. Reece +, Michael J. Kelley *+ Applied Science Department, College of William and
More informationperformance analysis of polymer electrolyte fuel cell stacks using electrochemical impedance spectroscopy
Loughborough University Institutional Repository An electrical circuit for performance analysis of polymer electrolyte fuel cell stacks using electrochemical impedance spectroscopy This item was submitted
More informationUgur Pasaogullari, Chao-Yang Wang Electrochemical Engine Center The Pennsylvania State University University Park, PA, 16802
Computational Fluid Dynamics Modeling of Proton Exchange Membrane Fuel Cells using Fluent Ugur Pasaogullari, Chao-Yang Wang Electrochemical Engine Center The Pennsylvania State University University Park,
More informationHigh-resolution on-chip supercapacitors with ultra-high scan rate ability
Electronic Supplementary Material (ESI) for Journal of Materials Chemistry A. This journal is The Royal Society of Chemistry 214 Supporting Information High-resolution on-chip supercapacitors with ultra-high
More informationProton Conductive Membrane Compressor-Driven Pulse Tube Cryocooler
Proton Conductive Membrane Compressor-Driven Pulse Tube Cryocooler James R. Muller 1, Lonnie G. Johnson 1, Carl S. Kirkconnell 2 and Robert Hon 2 1 Johnson Research and Development Atlanta, Georgia, USA
More informationSIMULATION-BASED development methods are increasingly
742 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 41, NO. 3, MAY/JUNE 2005 Impedance-Based Simulation Models of Supercapacitors and Li-Ion Batteries for Power Electronic Applications Stephan Buller,
More information