MYTECH CORPORATION. 180 Old Tappan Rd., Bldg. 6, Old Tappan, NJ Tel: (201) Fax: (201)

Size: px

Start display at page:

Download "MYTECH CORPORATION. 180 Old Tappan Rd., Bldg. 6, Old Tappan, NJ Tel: (201) Fax: (201)"

Bertha Douglas
5 years ago
Views:

1 CUSTOMER : M O D E L : DESCRIPTION : LCD MODULE MYTECH CORPORATION 180 Old Tappan Rd., Bldg. 6, Old Tappan, NJ Tel: (201) Fax: (201) mysales@mytechcorp.com NOTE: 1. This specification may, wholly or partially, be subjected to change without notice. 2. Information contained herein is proprietary information of MYTECH CORPORATION. The dissemination use or duplication for any purpose other than for which the information is provided is prohibited by MYTECH CORPORATION except by express permission.

2 02 of General Specification (1) Mechanical Dimension Item Standard Value Unit Number of dots 320x240 dots Outline dimension 166.8(W)x 109.0(H)x 11.0max(T) mm View area 122.0(W)x 92.0(H) mm Active area (W)x 86.38(H) mm Dot size 0.34(W)x 0.34(H) mm Dot pitch 0.36(W)x 0.36(H) mm (2) Controller IC: SED1335 (3) Temperature Range Normal Wide Operating 0 ~ ~+70 Storage -10 ~ ~+80 (4) Polarizer FSTN / black / Negative, STN / blue / Negative : Anti-glare Polarizer

3 03 of Absolute Maximum Ratings Item Symbol Min Typ Max Unit Operating Temperature T OP Storage Temperature T ST Input Voltage V I 0 V DD V Supply Voltage For Logic V DD V Supply Voltage For LCD V DD -V EE 0 32 V 3. Electrical Characteristics Item Symbol Condition Min. Typ. Max. Unit Logic Voltage V DD -V SS V Supply Voltage For LCD V DD -V O Ta= V Ta= V Ta= V Input High Volt. V IH 0.8V DD V DD V Input Low Volt. V IL 0 0.2V DD V Output High Volt. V OH V DD -0.4 V Output Low Volt. V OL 0.4 V Supply Current I DD 110 ma IEE 3.0 ma 4. Optical Characteristics a. STN Item Symbol Condition Min. Typ. Max. Unit View Angle (V) CR deg (H) CR deg Contrast Ratio CR 3 Response Time 25 T rise ms T fall ms

4 04 of 15 b. FSTN Item Symbol Condition Min. Typ. Max. Unit View Angle (V) CR deg (H) CR deg Contrast Ratio CR 5 Response Time 25 T rise ms T fall ms Polarizer FSTN / black / Negative, STN / blue / Negative: Anti-glare Polarizer 4.1 Definitions View Angles Contrast Ratio Visual angle direction ) Z ( Y X Nonselected Condition Brightness (%) Selected Condition Brightness at selected state ( BS ) CR = Brightness at non-selected state ( Bns ) Selected state Bns Non-selected state Bs Operating voltage for LCD driving Nonselected Condition Brightness 100 % 10 % 90 % tr td Rise Time Decay Time ( fall time tf )

5 05 of 15 Response time 5. Interface Description Pin No. Symbol Level Description 1 V SS 0V Ground 2 V DD 5.0V Power supply for Logic (option +3V) 3 V O (Variable) Driving voltage for LCD 4 A0 H/L RD=L WR=H,A0=L :Data Read AO=H :Status read RD=H WR=L,A0=L :Data Write AO=H :Command write 5 WR H/L 8080 family: Write signal, 6800 family: R/W signal 6 RD H/L 8080 family: Read signal, 6800 family: Enable clock 7~14 DB0~DB7 H/L Data bus 15 CS H/L Chip select, Active L 16 RES H/L Controller reset signal, Active L 17 V EE Negative voltage output 21.3V (Optional) 18 SEL1 H:6800,L: FGND Frame Ground 20 NC No connection

6 06 of Block Diagram From MPU FLM /RD /WR /CS A0 DB0~7 /RESET Controller SED1335 LP, /DISPOFF COM. Driver 240 LCD Panel 320 x 240 Dots 320 SRAM (32K) CP,D0~D3 SEG. Driver

7 07 of Timing Characteristics Family Interface Timing Parameter Condition Symbol Min Max Unit Remark Address Hold Time tah8 10 ns Address Setup Time taw8 0 ns A0,/CS System Cycle Time tcyc Note ns Strobe Pulse Width CL=100 pf toc 150 ns /WR,/RD Data Setup Time VDD=2.7~4.5 tds8 120 ns Data Hold Time tdh8 5 ns /RD Access Time tacc8-80 ns DB0~DB7 Output Disable Time toh ns Note: For memory control and system control commands: tcyc8=2tc+toc+tcea+75 > tacv +245 For all other commands: tcyc8=4tc+toc+30 A0,/CS /WR,/RD DB0~DB7 (Write) DB0~DB7 (Read)

8 08 of Family Interface Timing Parameter Condition Symbol Min Max Unit Remark System Cycle Time tcyc6 Note ns A0,/CS, Address Setup Time taw6 10 ns R/W Address Hold Time tah6 0 ns Data Setup Time CL=100 pf tds6 120 ns Data Hold Time VDD=2.7~4.5 tdh6 0 ns Output Disable Time toh ns DB0~DB7 Access Time tacc6-130 ns Enable Pulsewidth tew ns E Note: For memory control and system control commands: tcyc6=2tc+tew+tcea+75 > tacv +245 For all other commands: tcyc6=4tc+tew+30 E R/W A0, /CS DB0~DB7 (Write) DB0~DB7 (Read) AC Electrical Characteristics

9 09 of 15 Class Command Code /RD /WR A0 D7 D6 D5 D4 D3 D2 D1 D0 Hex Command Description Command read parameters Number of Section byters System SYSTEM Initialized Device and display Control SLEEP IN Enter Standby mode DISP D 58, Enable and disable display and SCROLL set Display start address and CSRFORM D Set cursor byte Display Control CGRAM C Set start address of character CD CD CSRDIR C Set direction of cursor to movement 4F HDOT SCR A set horizontal scroll position OVLAY B set display overlay format Drawing CSRW set cursor address Control CSRR read cursor address Memory MWRITE write to display memory Control MREAD read from display memory Note: 1. In general, the internal registers of the SED1335F are modified as each command parameter is input. However, the microprocessor does not have to set all the parameters of a command and may send a new command before all parameters have been input. The internal registers for the parameters that have been input will have been changed but the remaining parameter registers are unchanged. 2 bytes parameters( where two bytes are treated as 1 data item) are handled as following: a. CSRW, CSRR: Each byte is processed individually. The microprocessor may read or write just the low byte of the cursor address. b. SYSTEM SET, SCROLL, CGRAM ADR. : Both parameter bytes are processed together. If the command is changed after half of the parameter has been input, the single byte is ignored. 2. APL and APH are 2-byte parameters, but are treated as two 1-byte parameters. 3. Please refer to SED1335F LCD Controller Data Book for detail.

10 10 of Power Supply for LCD Module and LCD Operating Voltage a Adjustment (Optional) LCM operating on " DC 3V or 5V " input with external negative voltage. LCD Module block diagram (Optional) LCM operating on "DC 3V or 5V" input with built-in negative voltage LCM Vdd built-in N.V generator or Temp. compensation circuit Vo -21.3V Vee Vss VR DC V

11 11 of Backlight Information 10.1 Specification (1) LED edge/white Parameter Symbol Min Typ Max Unit Test Condition Supply Current ILED ma V=3.5V Supply Voltage V V Reverse Voltage VR 8 V Luminous Intensity IV 100 cd/m 2 ILED=160mA Life Time Hr. V 3.8V Color White (2) CCFL / white (Ta=25 ) Item Symbol Specification Min Typ Max Unit Condition Driving Voltage V FL 278 Vrms Input current I FL marms Power consumption W 1.35 W Starting Voltage V FLS 530 Vrms Luminance L 550 Cd/m 2, =0 deg, I FL =5.0mArms Chromaticity x y Luminance Uniformity (Testing 9 point) 75% %, =0 deg, I FL =5.0mArms Life time hrs Color White

12 MYTECH 10.2 Backlight driving methods a. LED B/L driven from A.K cable directly 12 of 15 LCM Blacklight b. CCFL B/L driven from A.K cable directly LCM CCFL Blacklight AC DC

13 11. Quality Assurance 13 of 15 Screen Cosmetic Criteria No. Defect Judgement Criterion Partition 1 Spots 2 Bubbles Polarize 3 Scratch 4 Allowable Density 5 Coloration in A)Clear Size: d mm active area d <d <d Acceptable Qty in Disregard 0.3<d 0 Note: Including pin holes and defective dots Minor which must be within one pixel size. B)Unclear Size: d mm Acceptable Qty in active area d 0.2 Disregard 0.2<d <d <d 0 Size: d mm active area d 0.3 Acceptable Qty in Disregard 0.3<d <d <d 0 Minor In accordance with spots cosmetic criteria. When the light reflects on the panel surface, Minor the scratches are not to be remarkable. Above defects should be separated more than 30mm each other. Not to be noticeable coloration in the viewing area of the LCD panels. Back-light type should be judged with back-light on state only. Minor Minor

14 12.Reliability Content of Reliability Test 14 of 15 Environmental Test No. Test Item Content of Test Test Condition Applicable Standard 1 High Temperature storage Endurance test applying the high storage temperature for a long time hrs 2 Low Temperature storage Endurance test applying the high storage temperature for a long time hrs 3 High Temperature Operation Endurance test applying the electric stress (Voltage & Current) and the thermal stress to the element for a long time hrs 4 Low Temperature Operation Endurance test applying the electric stress under low temperature for a long time hrs High Temperature/ 5 Humidity Storage High Temperature/ 6 Humidity Operation Temperature Cycle 7 Mechanical Test Endurance test applying the high temperature and high humidity storage for a long time. 60,90%RH 96hrs Endurance test applying the electric stress 50,90%RH (Voltage & Current) and temperature / humidity stress to the element for a long time. 96hrs Endurance test applying the low and high temperature cycle min 5min 30min 1 cycle -10 /60 10 cycles 8 Vibration test Endurance test applying the vibration during transportation and using. 10~22Hz 1.5mmp-p 22~500Hz 1.5G Total 0.5hrs 9 Shock test Constructional and mechanical endurance test applying the shock during transportation. 50G Half sign wave 11 msedc 3 times of each direction 10 Atmospheric test pressure Endurance test applying the atmospheric pressure during transportation by air. 115mbar 40hrs Others 11 Static electricity test Endurance test applying the electric stress to the terminal. VS=800V,RS=1.5k CS=100pF 1 time ***Supply voltage for logic system=5v. Supply voltage for LCD system =Operating voltage at 25

15 13. Outline Drawing 15 of 15 LCM DRAWING 11.0MAX /3 0 mm 1/ (VA) (AA) (AA) (VA) Conducl on Buttom side (pitch 1.0mm FFC)

SPECIFICATIONS FOR LCD MODULE

SPECIFICATIONS FOR LCD MODULE MODEL NO. BG320240F-87a$ series VER.01 FOR MESSRS: ON DATE OF: APPROVED BY: BOLYMIN, INC. 13F-1, 20, TA-LONG RD., TAICHUNG CITY 403, TAIWAN, R.O.C. WEB SITE:http://www.bolymin.com.tw