AMC2004HR-B-Y6WFDY-SP

Size: px

Start display at page:

Download "AMC2004HR-B-Y6WFDY-SP"

Agnes Butler
5 years ago
Views:

1 45 Royal rest ourt Unit 42 Markham, ON, anada L3R 9Z4 Tel: Fax: LD MODULE SPEIFITIONS M2004HR-B-Y6WFDY-SP 20 HRTERS X 4 LINES OUTLINE DIMENSION: 65.0 X 28.4 MM VIEWING RE: 46.0 X 8.4 MM HRTER SIZE:.85 X 3.5 MM DISPLY MODE: YELLOW/GREE STN, TRNSFLETIVE BKLIGHT: YELLOW/GREEN TEMPERTURE: WIDE REVISION REORD REV. DTE PGE OMMENT NEW RELESE

2 ONTENTS. MEHNIL HRTERISTIS. MEHNIL DT.2 MEHNIL DRWINGS 2. IRUIT BLOK DIGRM 2. Electrical Block Diagram 2.2 Pins Definition 2.3 Power Supply For LM Driving 2.3 Display haracter ddress ode 3. BSOLUTE MXIMUN RTINGS 3. Electrical bsolute Maximum Ratings 3.2 Enviromental bsolute Maximum Ratings 4. ELETRIL HRTERISTIS 4. D haracteristics 4.2 haracteristics 5. BKLIGHT HRTERISTIS 5. bsolute Maximum Ratings 5.2 Operating Parameters 6. ELETRO-OPTIL HRTERISTI 7. DISPLY ONTROL INSTRUTION 7. INSTRUTION TBLE 7.2 haracter Table 8. INSPETION STNDRDS 9. PREUTIONS IN USING LM

3 . MEHNIL HRTERISTIS. MEHNIL DT ITEM STNDRD VLUE UNIT NUMBER OF HRTERS 20 HRTERS X 4 LINES HRTER FORMT 5 X 7 DOTS PLUS URSOR OUTLINE DIMENSIONS 65.0(W) X 28.4(H) X 9.0(T) mm EFFETTVE VIEWING RE 46.0(W) X 8.4(H) mm HRTER SIZE.85(W) X 3.5(H) mm HRTER PITH 2.5(W) X 4.25(H) mm DOT SIZE 0.33(W) X 0.35(H) mm DOT PITH 0.38(W) X 0.40(H) mm PPROX WEIGHT TBD g

4 .2 MEHNIL DRWINGS 6 PITH.0

5 2. IRUIT BLOK DIGRM 2. Electrical Block Diagram 2.2 Pins Definition PIN SYMBOL FUNTION Vss Power Supply(GND) 2 Vdd Power Supply(+5.0/+3.0V) 3 Vo Input Voltage to Booster 4 RS Instruction/Data Register Select 5 R/W Data Bus Line 6 E Enable Signal 7-4 DB0-DB7 Data Bus Line 5 Power Supply for LED B/L(+4.V) 6 K Power Supply for LED B/L(-) 2.3 Power Supply For LM Driving LD Vdd +5V/+3V MODULE V0 VR Vdd Vss GND V0: VOLTGE TO THE VOLTGE ONVERTER VR: 0K - 20K

6 NOTE: When working at 3.3V, please change R2 from.0k to 0 OHM 2.4 Display haracter ddress ode POSITION LINE B 0 0D 0E 0F DDRESS LINE B 2 2D 2E 2F LINE B 4 4D 4E 4F LINE B 6 6D 6E 6F *NOTE: LL OF THE NUMBERS RE IN HEX FORMT 3. BSOLUTE MXIMUN RTINGS 3. Electrical bsolute Maximum Ratings ITEM SYMBOL ONDITION MIN MX UNIT Supply Voltage (Logic) Vdd Vss V Supply voltage for LD driving Vlcd - Vdd-5 Vdd+0.3 V Input Voltage Vi - 0 Vdd V 3.2 Enviromental bsolute Maximum Ratings ITEM SYMBOL ONDITIONS MIN MX UNIT Operating Temp Topr Extended temp deg Storage Temp Ttsg version deg Humidity Endurance RH no ondensation Ta<=40 deg - 95 % Vibration Hz, X/Y/Z - 4.9m/ss - directions, hour 0.5g Shock - 0 ms X/Y/Z 29.4m/ss - direction time 3.0g each

7 4. ELETRIL HRTERISTIS 4. D haracteristics Electrical haracteristics at Ta=-30 to 85 deg, Vdd =2.7V to 5.5V ITEM SYMBOL ONDITION MIN TYP MX UNIT Supply Voltage (logic) Vdd-Vss V Supply Voltage (LD) Input signal Voltage (for E, DB0-7,R/W,RS) Supply urrent (logic) Supply urrent (LD) V0 Vdd = 5.0V V Vdd=3.0V V V-ih H level 0.7Vdd - Vdd V V-il L level V Icc m Io m 4.2 haracteristics TIMING SPEIFITIONS at Ta = -30 to 80 deg, Vdd = 2.7 to 4.5V, For Write mode ITEM SYMBOL MIN MX UNIT E cycle time tc ns E rise time tr - 25 ns E fall time tf - 25 ns E-pulse width (H, L) tw ns R/W and RS set-up time tsul 60 - ns R/W and RS hold time th 20 - ns Data set-up time tsu ns Data hold time th2 0 - ns

8 For Read mode ITEM SYBOL MIN MX UNIT E cycle time tc ns E rise time tr - 25 ns E fall time tf - 25 ns E-pulse width (H, L) tw ns R/W and RS set-up time tsu 60 - ns R/W and RS hold time th 20 - ns Data output delay td ns Data hold time tdh 5 - ns WRITE MODE TIMING DIGRM RS tsu th th R/W E tr tw tsu2 th tf th2 DB0-DB7 Valid Data tc RED MODE TIMING DIGRM RS tsu th th R/W E tr td tw th tf tdh DB0-DB7 Valid Data tc

9 5. BKLIGHT HRTERISTIS 5. bsolute Maximum Ratings ITEM SYMBOL ONDITION MIN MX UNIT Forward urrent Ifm m Reverse Voltage Vr V Power Dissipation Pd mw 5.2 Operating Parameters ITEM SYMBOL ONDITION MIN TYP. MX UNIT Forward Voltage Vf* If=20m V Peak Wavelength If=20m nm *Vf is the voltage between Pin5 and Pin6. There is NO current limiting resistors on the module PB. 6. ELETRO-OPTIL HRTERISTIS ITEM SYMBO ONDI L TION MIN. TYP. MX. UNIT REF. ontrast R Note Rise Time tr ms Note2 Fall Time tf ms note 2 Viewing ngle Frame Frequency Ø, Ø Ff Note(): ontrast ratio is defined under the following condition: R= brightness of selected condition brightness of non-selected condition (a). Temperature (b). Frame Frequency Hz 70 DEG Note 3 -- Hz note 2

10 (c). Viewing angle =0, Ø=0 (d). Operating Voltage---5.0V Note(2): definition of response time: +Vop /f F 0 -Vop -brightness 90% 0% tr tf ondition: (a). Temperature (b). Frame Frequency Hz (c). Viewing angle =0, Ø=0 (d). Operating Voltage---5.0V Note(3): definition of view angle: TOP-BOTTOM DIRETION TOP RIGHT-LEFT DIRETION 2 2 BOTTOM LEFT RIGHT

11 7. DISPLY ONTROL INSTRUTION 7. INSTRUTION TBLE Functio R R R D D D D D D D D Description Execu n E S W B B B B B B B B Time* (Max) lear X Write 20H to DDRM and set DRM address to.53ms Display 00H from Return Home X X Return the cursor to the home position. DD RM.53mS contents remain unchanged. Set DD RM address to 00H Entry X I S Set cursor moving direction and enable the 39 S S mode set / D shift of the display. /D=: increment; /D=0: decrement; S=: whole display shift when data is written. S=0: display shift disable Display ON/OFF control Extended function set ursor or Display shift Scroll enable Function Set Set G RM add D B Set display (D),cursor() and blinking of 39 S S cursor(b) ON/OFF. D=:display ON; D=0: display OFF. =:ursor ON; =0:cursot OFF. B=:Blink ON; B=0, Blink OFF F B N ssign font width, black/white inverting of 39 S W WWcursor, and 4-line display mode control bit. FW=:6-dot font width; FW=0: 5-dot font width;bw=: black/white inverting of cursor enable; BW=0: black/white inverting of cursor disable; NW=: 4-line display mode; NW=0: -line or 2-line display mode S R X X Move the cursor and shift the display without 39 S / / changing DDRM contents. S/=: Display Shift; L S/=0:ursor move. R/L=:shift to right; R/L=0:shift to left H H H H Determine the line for horizontal smooth scroll. S S S S HS=/0: st line dot scroll enable/disable HS2=/0: 2nd line dot scroll enable/disable HS3=/0: 3rd line dot scroll enable/disable HS4=/0: 4th line dot scroll enable/disable D N R X X Set interface data length (DL), number of display L E lines (N) and extention register RE=0. DL=: 8 0 bits; DL=0: 4 bits. N=: 2 lines; N=0: lines D L N R E 3 2 B E L P 0 Set DL,N,RE( ) and GRM/SEGRM blink enable(be) BE=/0: blink enable/disable; LP=: low power mode; LP=0: normal operation mode Set G RM address. G RM data is sent and received after this setting. 39 S 39 S

12 Set SEGRM address Set DD RM ddress Set scroll quantity Read BF & ddr Write Data to RM Read Data from RM x x x S Q 5 4 S Q 4 3 S Q S Q 2 S Q 0 0 S Q 0 Set SEGRM address in address counter 39 S Set DD RM address. DD RM data is sent and 39 S received after this setting. Set the quantity of horizontal dot scroll 39 S x 0 B F Read BUSY FLG (BF) and the contents of the 0 S address counter. BF=: internal operation; BF=0: can accept instruction. x 0 WRITE DT Write data into DD RM or G RM. 43 S x 0 RED DT Read data from DD RM or G RM. 43 S

13 7.2 haracter Table (for )

14 8. INSPETION STNDRDS 8. Inspection onditions The LD shall be inspected under 40W white fluorescent light. The distance between the eyes and the samples shall be more than 30cm. ll directions for inspecting the sample should be within 45 degree against perpendicular line. 8.2 Definition of pplicable Zone Zone: ctive Display rea B Zone: rea from Bezel Frame to Zone Zone: Rest rea of Bezel Zone + B Zone=Effective Viewing rea 8.3 Standards NO PRMETER RITERI Black and White Spots, Foreign Substances Round Shape Zone cceptable Number DIMENSION(MM) B D 0. * * *

15 2 ir Bubbles (Between glass and polarizer) 0.<D * 0.2<D * 0.3<D 0 0 * D=(long+short)/2 * Disregard Line Shape Zone cceptable Number X(mm) Y(mm) B W * * * 2.0 L 0.03 W 3 3 *.0 L 0.04 W 2 *.0 L 0.05 W 0 2 * <W Not acceptable X: Length Y: Width * Disregard Total defects shall not exceed 5. Dimension(mm) Zone cceptable Number B D 0. * * * 0.<D * 0.2<D * 0.3<D 0 0 * *: Disregard Total defects shall not exceed 3. () Dot Shape(with dent) 3 The Shape of Dot s per the sketch of left hand. (2) Dot Shape(with Projection) Should not connect to next dot. (3) Pin Hole

16 4 Polarizer Scratches 5 Polarizer Dirts (X+Y)/2<0.2mm (less than 0.mm is not counted Total defects shall not exceed 5. Not to be conspicuous defects. If the stains are removed easily from LD surface,the module is not defective. 6 olor Variation Not to be conspicuous defects. 9. PREUTIONS IN USING LM. LIQUID RYSTL DISPLY (LD) LD is made up of glass, organic sealant, organic fluid, and polymer based polarizers. The following precautions should be taken when handing, (). Keep the temperature within range of use and storage. Excessive temperature and humidity could cause polarization degradation, polarizer peel off or bubble. (2). Do not contact the exposed polarizers with anything harder than an HB pencil lead. To clean dust off the display surface. Wipe gently with cotton. hamois or other soft material soaked in petroleum benzin. (3). Wipe off saliva or water drops immediately. ontact with water over a long period of time may cause polarizer deformation or color fading, while an active LD with water condensation on its surface will cause corrosion of ITO electrodes. (4). Glass can be easily chipped or cracked from rough handing. especially at corners and edges. (5). Do not drive LD with D voltage. 2. Liquid rystal Display Modules 2. Mechanical onsiderations LM are assembled and adjusted with a high degree of precision. void excessive shocks and do not make any alterations or modifications. The following should be noted. (). Do not tamper in any way with the tabs on the tabs on the metal frame. (2). Do not modify the PB by drilling extra holes, changing its outline, moving its components or modifying its pattern. (3). Do not touch the elastomer connector, especially insert an backlight panel (for example, EL). (4). When mounting a LM make sure that the PB is not under any tress such as bending or twisting. Elastomer contacts are very delicate and missing pixels could result from slight dislocation of any of the elements. (5). void pressing on the metal bezel, otherwise the elastomer connector could be deformed and lose contact, resulting in missing pixels Static Electricity LM contains MOS LSI s and the same precaution for such devices should apply, namely (). The operator should be grounded whenever he/she comes into contact with the

17 module. Never touch any of the conductive parts such as the LSI pads, the copper leads on the PB and the interface terminals with any parts of the human body. (2). The modules should be kept in antistatic bags or other containers resistant to static for storage. (3). Only properly grounded soldering irons should be used. (4). If an electric screwdriver is used, it should be well grounded and shielded from commutator sparks. (5). The normal static prevention measures should be observed for work clothes and working benches; for the latter conductive ( rubber) mat is recommended. (6). Since dry air is inductive to statics, a relative humidity of 50-60% is recommended Soldering (). Solder only to the I/O terminals. (2). Use only soldering irons with proper grounding and no leakage. (3). Soldering temperature: (4). Soldering time: 3 to 4 sec. (5). Use eutectic solder with resin flux fill. (6). If flux is used, the LD surface should be covered to avoid flux spatters. Flux residue should be removed after wards Operation (). The viewing angle can be adjusted by varying the LD driving voltage V0. (2). Driving voltage should be kept within specified range; excess voltage shortens display life. (3). Response time increases with decrease in temperature. (4). Display may turn black or dark blue at temperatures above its operational range; this is (however not pressing on the viewing area) may cause the segments to appear fractured. (5). Mechanical disturbance during operation (such as pressing on the viewing area) nay cause the segments to appear fractured Storage If any fluid leaks out of a damaged glass cell, wash off any human part that comes into contact with soap and water. Never swallow the fluid. The toxicity is extremely low but caution should be exercised at all the time Limited Warranty Unless otherwise agreed between Orient Display and customer, Orient Display will replace or repair any of its LD and L, which is found to be defective electrically and visually when inspected in accordance with Orient Display acceptance standards, for a period on one year from data of shipment. onfirmation of such date shall be based on freight documents. The warranty liability of Orient Display is limited to repair and/or replacement on the terms set forth above. Orient Display will not responsible for any subsequent or consequential events.

AMC2404AR-B-B6WTDW-SP

145 Royal Crest Court Unit 42 Markham, ON, Canada L3R 9Z4 Tel: 905-477-1166 Fax: 905-477-1782 http://www.orientdisplay.com LCD MODULE SPECIFICATIONS AMC2404AR-B-B6WTDW-SP 24 CHARACTERS X 4 LINES OUTLINE