Product Specification 2013-10-21 FPC Connector 0.5mm Pitch SMT Type Bottom Contact H:2.0 Update List: Item Update Description Rev. Issued Date Revisor 1 New Edit A 2013/10/21 DLITY Prepared By DLITY Rechecked By DLITY Approved By Mark Document No.:BY-RD089 Product Name: FPC CONN. Page 1 of 6
1. SCOPE This Specification covers the FPC0520 Series Connector. 2. ORDERING INFORMATION PART NO.: FPC 05 20 - xx Rx - Tx x 1 2 3 4 5 6 7 1 Series name FPC 2 Pitch between 0.5 mm Pitch 3 Series Number 20 4 Number of terminals 04~61 5 Assembly style Right Angle/Lower Contact Type SMT Type 6 Packaging TA :Tape Reel Tu:Tube 7 Plating 0=Tin over Nickel G=Gold flash over Nickel 3. CONNECTOR DIMENSIONS See attached drawings. 4. MATERIAL Housing : Actuator Hight-Temp plastic Color : Nature Flammability Rating (UL94V-0) Hight-Temp plastic Color : Black Flammability Rating (UL94V-0) Copper alloy Copper alloy Terminal : Peg: Terminal Plating See Ordering Information Peg Plating: Tin over Nickel 5. ACCOMMODATED P.C.B. LAYOUT See attached drawings. Document No.:BY- RD088 Product Name: FPC CONN. Page 2 of 6
6. RATING ITEM STANDARD Operating Voltage (Max.) 50V AC Current Rating (Max.) 0.5A Operating Temperature -25 C ~ +85 C (Including terminal temperature rise) 7. PERFORMANCE Test Item Procedure Requirement 1 Examination of Product 2 Contact Resistance 3 Dielectric withstanding Voltage 4 Insulation Resistance Visual inspection. Electrical Requirement Subject mated contacts assembled in housing to 20mV Max open circuit at 100mA Max. Refer to Fig.1 [ 250 ]VAC for 1minute Test between adjacent circuits of unmated connector. Impressed voltage 500 VDC. Test between adjacent circuits of unmated connector. Mechanical Requirement Meets requirements of product drawing. No physical damage. [40]mOhmMax [No creeping discharge or flashover shall occur. Current leakage: 0.5 ma MAX [ 100 ] M Ohm Min.(Initial) 5 Contact / Peg Retention Force 6 FPC/FFC Retention Force 7 Durability 8 Vibration 9 Mechanical Shock Apply axial pull out force at the rate of [25±3]mm/minontheterminal assembled in the housing. Operation Speed:[ 25±3 ] mm/min Measure the force required to unmate connector. Operation Speed:[ 10 ] cycle-max./min Durability Cycles:10 Cycles Subject mated connectors to 10-55-10 Hz traversed in 1minutes at 1.52mm amplitude 2 Hours each of 3 mutually perpendicular planes. 100mA Max. Applied. Accelerate Velocity:490m/s 2 (50G) Waveform:Half-sine shock plus Duration:11msec No. of Drops:3 drops each to normal and reversed directions of X, Y and Z axes, totally 18 drops, passing DC 100mA max. Current during the test. 0.100 kgf Min./Pin. 0.045 kgf/pin Min. Contact Resistance: [60]mOhmMax Discontinuity: 1μsec Max. Discontinuity: 1μsec Max. Document No.:BY- RD088 Product Name: FPC CONN. Page 3 of 6
Test Item Requirement Procedure Environmental Requirements 10 Temperature Rising 11 Solder ability 12 Resistance to Reflow Soldering Heat 13 Cold Resistance 14 Thermal Cycling 15 Humidity 16 Salt Spray Contact series-wired, apply test current of loaded rating current to the circuit, and measure the temperature rising by probing on soldered areas of contacts, after the temperature becomes stabilized deduct ambient temperature from the measured value. Steam Aging Preconditioning: Intended for no-tin lead and no-tin lead -alloy finished for 93+3/-5 8hrs. Solder pot temperature: 245 ±5, 4~5sec Pre Heat:150~180, 60~90sec. Heat:230 Min., 40sec Min. Peak Temp.:260+0/-5, 10sec.or less Duration:2 cycles See: 8. INFRARED REFLOW CONDITION Put the sample in low temperature box to 0.7~1.0 degrees to -25±3 measured after 96 hrs at room temperature for 2 hrs to check(based upon JISC0020) 35 Max. Under loaded rating current The inspected area of each lead must have 95% solder coverage minimum. No physical damage shall occur. (Lead-Free) See Product Qualification and Test Sequence Grop11 Contact Resistance: 60m Ohm Max Mated Connector -55+/-3 (30 min.), +85+/-2 (30 See Product Qualification and min) Test Sequence Perform this a cycle, repeat 5 cycles Grop4 Mated Connector 38~42, 90~95% RH, 96hours Subject mated connectors to 35+/-2 and 5+/-1% salt condition for 48hours. After test, rinse the sample with water and recondition the room temperature for 1 hour. EIA-364-26B, Condition B Figure 1(End) See Product Qualification and Test Sequence Grop4 No detrimental corrosion allowed in contact area and base metal exposed. See Product Qualification and Test Sequence Grop7 NOTE:Shall meet visual requirements, show no physical damage, and meet requirement of additional tests as specified in the test sequence in Figures 2 Document No.:BY- RD088 Product Name: FPC CONN. Page 4 of 6
7.1. Product Qualification and Requalification test Test Group Test or Examination 1 2 3 4 5 6 7 8 9 Test Sequence(a) Examination of Product 1,4 1,7 1,4 1,4 1,3 Contact Resistance 2,5 1,4 2,10 2,5 2,5 Insulation Resistance 3,9 Dielectric withstanding Voltage 4,8 Temperature Rising 1 Durability 3 Vibration 2 Mechanical Shock 3 Thermal Shock 5 Humidity 6 Temperature Cycling 3 Temperature Life 3 Salt Spray 1 Solder ability 1 FPC/FFC Retention Force 2 Resistance to Soldering Heat Sample Size 2 4 4 4 4 4 2 4 4 Figure 2 NOTE:(a)Numbers indicate sequence in which tests are performed. (b)discontinuities shall not take place in this test group, during tests. Document No.:BY- RD088 Product Name: FPC CONN. Page 5 of 6
8. INFRARED REFLOW CONDITION 260 C MAX.(Peak Temp.)5~10Sec. C 230 C MIN. / 30~50Sec. 230 200 150 100 50 0 Start 60 Sec. 60~90 Sec. 30 Sec. Time(sec.) NOTE: Please check the re-flow soldering condition by your own devices beforehand. Because the condition changes by the soldering devices, p.c. boards, and so on. 9. TAPE AND REEL PACKAGE SPECIFICATION 9-1.Tape and Reel Dimensions:See attached drawings. 9-2.Specification Document No.:BY- RD088 Product Name: FPC CONN. Page 6 of 6