SCOPE: QUAD, SPST, HIGH SPEED ANALOG SWITCH Device Type Generic Number SMD Number DG44A(x)/883B 56-04MC DG44A(x)/883B 56-04MC Case Outline(s). The case outlines shall be designated in Mil-Std-835 and as follows: Outline Letter Mil-Std-835 Case Outline Package Code MAXIM SMD K E GDIP-T6 or CDIP-T6 6 LEAD CERDIP J6 Z CQCC-N0 0-Pin Ceramic LCC L0 Absolute Maximum Ratings Voltage Referenced to V - V + to V -... 44V V - to GND... 5V Digital Inputs to V- /... (GND-0.3V) to 44V dc Digital Inputs, V S, V D /...(V - ) -V to (V + )+V or 30mA whichever occurs first Continuous Current, Any terminal... 30mA Peak Current, S or D (Pulsed at ms, 0% duty cycle max)... 40mA Lead Temperature (soldering, 0 seconds)... +300 C Storage Temperature... -65 C to +50 C Continuous Power Dissipation...... T A =+70 C 6 lead CERDIP(derate 0.0mW/ C above +70 C)..... 800mW 0 lead LCC (derate.mw/ C above +70 C)...... 77mW Junction Temperature T J.... +50 C Thermal, Junction to Case, ΘJC: Case Outline 6 lead CERDIP...... 50 C/W Case Outline 0 lead LCC...... 0 C/W Thermal, Junction to Ambient, ΘJA: Case Outline 6 lead CERDIP...... 00 C/W Case Outline 0 lead LCC...... 0 C/W Recommended Operating Conditions Ambient Operating Range (T A )...... -55 C to +5 C Positive Supply Voltage (V + )...... +5V Negative Supply Voltage (V - )...... -5V V AL (max)...... 0.8V V AH (min).......4v NOTE : Signals on S, D, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward current to maximum current ratings. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of DG44A/DG44A/883B -037 Rev. B for SMD 56-04 Page of 7
TABLE. ELECTRICAL TESTS: TEST SWITCH Analog-Signal Range Source-OFF Source-OFF Drain-OFF Drain-OFF Channel-On Channel-On INPUT Input Current/Voltage High Input Current/Voltage Low SUPPLY Positive Supply Current Symbol CONDITIONS -55 C <=T A <= +5 C V + =+5V, V - =-5V, GND=0V V AH =.4V, V AL =0.8V Unless otherwise specified Group A Subgroup Device type Min Max V ANALOG,,3-5 5 V I S(OFF) I S(OFF) I D(OFF) I D(OFF) I D(ON) + I S(ON) I D(ON) + I S(ON) I INH I S =-0mA, V D =±8.5V, V + =3.5V, V - =-3.5V, V IN =0.8V I S =-0mA, V D =±8.5V, V + =3.5V, V - =-3.5V, V IN =.4V I S =-0mA, V D =3.0V, V + =0.8V, V - =0V, V IN =0.8V I S =-0mA, V D =8.0V, V + =0.8V, V - =0V, V IN =0.8V I S =-0mA, V D =3.0V, V + =0.8V, V - =0V, V IN =.4V I S =-0mA, V D =8.0V, V + =0.8V, V - =0V, V IN =.4V V + =6.5V, V - =-6.5V, V IN =.4V V S =±5.5V V D =±5.5V V + =6.5V, V - =-6.5V, V IN =0.8V V S =±5.5V V D =±5.5V V + =6.5V, V - =-6.5V, V IN =.4V V S =±5.5V V D =±5.5V V + =6.5V, V - =-6.5V, V IN =0.8V V S =±5.5V V D =±5.5V V + =6.5V, V - =-6.5V, V IN =0.8V V S =±5.5V V D =±5.5V V + =6.5V, V - =-6.5V, V IN =.4V V S =±5.5V V D =±5.5V V IN under test =.4V other =0.8V I INL V IN under test = 0.8V other =.4V I+ V + =6.5V, V - =-6.5V, V + =3.V, V - =0V,,3,3,3,3,3,3 85 00 85 00 60 00 60 00 60 00 60 00 - -0 0 - -0 - -0 - -0 - -40 - -40 0 0 0 40 40 Units,,3 - + µa,,3 - + µa,,3 0. ma ---------------------------- Electrical Characteristics of DG44A/DG44A/883B -037 Rev. B for SMD 56-04 Page 3 of 7
TEST Negative Supply Current Ground Current TABLE. ELECTRICAL TESTS: CONDITIONS -55 C <=T A <= +5 C Symbol V + =+5V, V - =5V, GND=0V V AH =.4V, V AL =0.8V Unless otherwise specified I- V + =6.5V, V - =-6.5V, V + =3.V, V - =0V, V + =6.5V, V - =-6.5V, Group A Subgroup Device type Min - -00 - -00 Max I GND,,3-00 µa V + =3.V, V - =0V, Functional Tests FT Verify the Truth Table 7,8 DYNAMIC Turn-On Time t ON V S =±0V, R L =k, C L =35pF ns 50 35 Units µa 0, 300 400 V S =8.0V, R L =k, C L =35pF V+=+V, V-=0V 400 450 OFF V S =±0V, R L =k, C L =35pF Figure 0, 0, 600 675 0 0 50 50 ns V S =8.0V, R L =k, C L =35pF V+=+V, V-=0V,0, 00 ORDERING INFORMATION: SMD NUMBER Pkg. Code DG44AK/883B 56-04MEA 6 CDIP DG44AZ/883B 56-04MC 0 LCC DG44AK/883B 56-04MEA 6 CDIP DG44AZ/883B 56-04MC 0 LCC ---------------------------- Electrical Characteristics of DG44A/DG44A/883B -037 Rev. B for SMD 56-04 Page 4 of 7
TRUTH TABLE TERMINAL CONNECTION LOGIC DG44A SWITCH TERMINAL NUMBER DG44A DG44A DG44A DG44A 0 ON J6 0LCC J6 0LCC OFF IN NC IN NC D IN D IN 3 S D S D LOGIC DG44A 4 V- S V- S SWITCH 5 GND V- GND V- 0 OFF 6 S4 NC S4 NC ON 7 D4 GND D4 GND 8 IN4 S4 IN4 S4 IN3 D4 IN3 D4 0 D3 IN4 D3 IN4 S3 NC S3 NC NC IN3 NC IN3 3 V+ D3 V+ D3 4 S S3 S S3 5 D NC D NC 6 IN NC IN NC 7 V+ V+ 8 S S D D 0 IN IN ---------------------------- Electrical Characteristics of DG44A/DG44A/883B -037 Rev. B for SMD 56-04 Page 5 of 7
QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil- Std-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 5:. Test Condition, A, B, C, or D.. TA = +5 C minimum. 3. Interim and final electrical test requirements shall be specified in Table. Quality conformance inspection shall be in accordance with of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection:. Tests as specified in Table.. Selected subgroups in Table, of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table. b. Steady-state life test, Method 005 of Mil-Std-883:. Test condition A, B, C, D.. TA = +5 C, minimum. 3. Test duration, 000 hours, except as permitted by Method 005 of Mil-Std-883. TABLE. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Group A Test Requirements Group C and D End-Point Electrical Parameters Subgroups per, Table *,, 3,,, 3, 7, 8,,0, * PDA applies to Subgroup only. ---------------------------- Electrical Characteristics of DG44A/DG44A/883B -037 Rev. B for SMD 56-04 Page 6 of 7