Loose Taped X CLASS (IEC 60384-4) - MKP Series Typical applications: interference suppression and «across-the-line» applications. Suitable for use in situations where failure of the capacitor would not lead to danger of electric shock. Insulated Insulated 0.5mm Note: series has replaced the. series and.47 series. For new design we suggest the use of the series. p 5.5 p 7.5 p = 37.5 ±0.05 0.6 or 0.8* 0.8 *See size table.. GENERAL TECHNICAL DATA Dielectric: polypropylene film. Plates: metal layer deposited by evaporation under vacuum. Winding: non-inductive type. s: tinned wire. Protection: plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94 V0. Marking: Manufacturer s logo, series, capacitance, tolerance, rated voltage, capacitor class, dielectric, climatic category, passive flammability category, manufacturing date, approvals, manufacturing plant. Climatic category: /0/56 IEC 668- Operating temperature range: - to +0 C Related documents: IEC 60384-4, EN 60384-4. electrical characteristics Rated voltage (V R ): 75Vac (/60Hz) / 560 Vdc 3Vac (/60Hz) / 630 Vdc Capacitance range: 0.0µF to 0µF Capacitance values: E6 series (IEC 663 Norm). Capacitance tolerances (measured at khz): ±0% (K); ±0% (M); tolerance ±5% (J) available upon request Dissipation factor (DF): tgδ 0-4 at +5 C ±5 C: 0 (6)* at khz * Typical value Insulation resistance: Temperature: +5 C±5 C Voltage charge time: min Voltage charge: Vdc x0 5 MΩ (5x0 5 MΩ ) * for C 0.33µF 3 s (5 s ) * for C>0.33µF * Typical value Test voltage between terminations (on all pieces): 5Vac for s + Vdc for s at +5 C±5 C 09/8 Box thickness (B) imum dimensions B max H max L max 0.0 All B +0. H +0. L +0. 5.0 <7.5 B +0. H +0. L +0.3 5.0 7.5 B +0. H +0. L +0.5.5 All B +0. H +0. L +0.3 7.5 All B +0. H +0. L +0.3 37.5 All B +0.3 H +0. L +0.3 test method and performance Damp heat, steady state: st Temperature: + C ± C Relative humidity (RH): 93% ±% 56 days nd Temperature: +60 C ± C Relative humidity (RH): 95% ±% 5 hours (d.c.)/ min Capacitance change C/C : 5% Endurance: Temperature: +0 C ± C 0 h Voltage applied:.5 x V R +0Vac 0. s/h (d.c.)/ min Capacitance change C/C : 0% Resistance to soldering heat: Solder bath temperature: +60 C ± 5 C Dipping time (with heat screen):0 s ± s Capacitance change C/C : % Winding scheme single sided metallized polypropylene film
Rated Cap. 75 Vac / 560 Vdc B H L p (V/ µs) 0. µf 4.0 9.0 3.0 0.0 0.6 5 R46 KF - - N0-0.05 µf 4.0 9.0 3.0 0.0 0.6 5 R46 KF - - N0-0.0 µf 4.0 9.0 3.0 0.0 0.6 5 R46 KF 0 - - N0-0.033 µf 5.0.0 3.0 0.0 0.6 5 R46 KF 330 - - M - 0.047 µf 5.0.0 3.0 0.0 0.6 5 R46 KF 470 - - N0-0.068 µf 6.0.0 3.0 0.0 0.6 5 R46 KF 680 - - M - 0.0 µf 6.0.0 3.0 0.0 0.6 5 R46 KF 3 - - M M 0. µf 5.0.0 8.0 5.0 0.6 4 R46 KI - - 0-0.05 µf 5.0.0 8.0 5.0 0.6 4 R46 KI - - 0-0.0 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 0 - - 0-0.033 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 330 - - 0-0.047 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 470 - - 0-0.068 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 680 - - 0-0.0 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 3 - - M - 0.5 µf 6.0.0 8.0 5.0 0.6 4 R46 KI 3 - - M - 0.5 µf 9.0.5 8.0 5.0 0.6 4 R46 KI 3 - - L - 0. µf 7.5 3.5 8.0 5.0 0.6 4 R46 KI 30 - - M - 0. µf 9.0.5 8.0 5.0 0.6 4 R46 KI 30 - - L - 0. µf 6.0 7.5 8.0 5.0 0.6 4 R46 KI 30 - - 0-0.33 µf 8.5 4.5 8.0 5.0 0.6 4 R46 KI 3330 - - N0-0.33 µf 0.0 6.0 8.0 5.0 0.8 4 R46 KI 3330 - - M - 0.33 µf 9.0.5 8.0 5.0 0.6 4 R46 KI 3330 - - N M 0.33 µf 7.5 8.5 8.0 5.0 0.8 4 R46 KI 3330 - - 0-0.33 µf 3.0.0 8.0 5.0 0.8 4 R46 KI 3330 - - 0-0.47 µf 7.5 8.5 8.0 5.0 0.8 4 R46 KI 3470 - - 0 M 0.47 µf 0.0 6.0 8.0 5.0 0.8 4 R46 KI 3470 - - N0 M 0.47 µf.0 9.0 8.0 5.0 0.8 4 R46 KI 3470 - - M - 0.56 µf.0 9.0 8.0 5.0 0.8 4 R46 KI 3560 - - N0-0.60 µf.0 9.0 8.0 5.0 0.8 4 R46 KI 36 - - N0-0.5 µf 6.0 5.0 6.5.5 0.8 R46 KN 3 - - 0-0. µf 6.0 5.0 6.5.5 0.8 R46 KN 30 - - M - 0.33 µf 6.0 5.0 6.5.5 0.8 R46 KN 3330 - - N0-0.47 µf 7.0 6.0 6.5.5 0.8 R46 KN 3470 - - N0-0.68 µf 0.0 8.5 6.5.5 0.8 R46 KN 3680 - - M -.0 µf 0.0 8.5 6.5.5 0.8 R46 KN 4 - - N M.0 µf.0 0.0 6.5.5 0.8 R46 KN 4 - - N - 0.47 µf 9.0 7.0 3.0 7.5 0.8 R46 KR 3470 - - 0-0.68 µf 9.0 7.0 3.0 7.5 0.8 R46 KR 3680 - - M -.0 µf.0 0.0 3.0 7.5 0.8 R46 KR 4 - - M -.5 µf 3.0.0 3.0 7.5 0.8 R46 KR 4 - - M -. µf 3.0 5.0 3.0 7.5 0.8 R46 KR - - M -. µf 4.0 8.0 3.0 7.5 0.8 R46 KR - - M - 3.3 µf 8.0 33.0 3.0 7.5 0.8 R46 KR 4330 - - M - 4.7 µf 8.0 33.0 3.0 7.5 0.8 R46 KR 4470 - - M - 4.7 µf.0 37.0 3.0 7.5 0.8 R46 KR 4470 - - M -.5 µf.0.0 4.5 37.5.0 R46 KW 4 - - M -. µf.0.0 4.5 37.5.0 R46 KW - - M M. µf 3.0 4.0 4.5 37.5.0 R46 KW - - M - 3.3 µf 6.0 8.5 4.5 37.5.0 R46 KW 4330 - - M - 4.7 µf 6.0 8.5 4.5 37.5.0 R46 KW 4470 - - M M 4.7 µf 9.0 3.0 4.5 37.5.0 R46 KW 4470 - - M - 6.8 µf 0.0.0 4.5 37.5.0 R46 KW 4680 - - M - 6.8 µf 4.0 44.0 4.5 37.5.0 R46 KW 4680 - - M - 0.0 µf 30.0 45.0 4.5 37.5.0 R46 KW 5 - - M - Rated voltage (K=75Vac) Mechanical version and packaging (Table ) Tolerance: K (±0%); M (±0%) X CLASS (IEC 60384-4) - MKP Series. mark has replaced all the following European National marks: Table IEC 60384-4 UL 44 CSA - C. No. UL 83 CSA - C. No.8 GB/T 447 04 + 5 -/+ ±5 certified for Approved according to IEC 60384-4 According to IEC 665 P.70 9.05.70 9.05 File No.V443 File CQC03899 CQC03884 0.0/5.0.5 0.0/5.0.5/7.5 (Digit 0 to ) Note: Ammo-pack is the preferred packaging for taped version. For capacitor connected in serial with main line (two - phase and three - phase net) application, please read the SHORT GUIDE TO CHOOSE THE RIGHT FILM CAPACITORS at pag. 78 and contact our Technical Service for choosing the safest solution. 5 5 E Series available upon request 5 09/8
Rated Cap. 75 Vac / 560 Vdc Rated voltage (K=75Vac) Mechanical version and packaging (Table ) Tolerance: K (±0%); M (±0%) B H L p (V/ µs) 0.033 µf 4.0 9.0 3.0 0.0 0.6 5 R46 KF 330 - - P0-0.047 µf 4.0 9.0 3.0 0.0 0.6 5 R46 KF 470 - - P0-0.068 µf 5.0.0 3.0 0.0 0.6 5 R46 KF 680 - - P0-0. µf 5.0.0 3.0 0.0 0.6 5 R46 KF 3 - - P M 0. µf 6.0.0 3.0 0.0 0.6 5 R46 KF 3 - - P0-0.5 µf 6.0.0 3.0 0.0 0.6 5 R46 KF 3 - - P0 M 0.5 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 3 - - P0-0. µf 6.0.0 8.0 5.0 0.6 4 R46 KI 30 - - P0-0.33 µf 7.5 3.5 8.0 5.0 0.6 4 R46 KI 3330 - - P0-0.33 µf 9.0.5 8.0 5.0 0.6 4 R46 KI 3330 - - P 0.33 µf 6.0 7.5 8.0 5.0 0.6 4 R46 KI 3330 - - P - 0.47 µf 8.5 4.5 8.0 5.0 0.6 4 R46 KI 3470 - - P0 0.47 µf 9.0.5 8.0 5.0 0.6 4 R46 KI 3470 - - P M 0.47 µf 6.0 7.5 8.0 5.0 0.6 4 R46 KI 3470 - - P M 0.47 µf 7.5 8.5 8.0 5.0 0.8 4 R46 KI 3470 - - P3-0.68 µf 0.0 6.0 8.0 5.0 0.8 4 R46 KI 3680 - - P M 0.68 µf.0 9.0 8.0 5.0 0.8 4 R46 KI 3680 - - P0-0.8 µf.0 9.0 8.0 5.0 0.8 4 R46 KI 380 - - P0 M 0.47 µf 6.0 5.0 6.5.5 0.8 R46 KN 3470 - - P - 0.56 µf 6.0 5.0 6.5.5 0.8 R46 KN 3560 - - P M 0.56 µf 7.0 6.0 6.5.5 0.8 R46 KN 3560 - - P0-0.68 µf 7.0 6.0 6.5.5 0.8 R46 KN 3680 - - P0 -.0 µf 8.5 7.0 6.5.5 0.8 R46 KN 4 - - P M.0 µf 0.0 8.5 6.5.5 0.8 R46 KN 4 - - P0 -.5 µf 0.0 8.5 6.5.5 0.8 R46 KN 4 - - P M.5 µf.0 0.0 6.5.5 0.8 R46 KN 4 - - P0 -. µf 3.0.0 6.5.5 0.8 R46 KN - - P0 M.0 µf 9.0 7.0 3.0 7.5 0.8 R46 KR 4 - - P0 -.5 µf.0 0.0 3.0 7.5 0.8 R46 KR 4 - - P0 -. µf 3.0.0 3.0 7.5 0.8 R46 KR - - P0-3.3 µf 4.0 8.0 3.0 7.5 0.8 R46 KR 4330 - - P0-4.7 µf 4.0 8.0 3.0 7.5 0.8 R46 KR 4470 - - P M 4.7 µf 8.0 33.0 3.0 7.5 0.8 R46 KR 4470 - - P0-6.8 µf.0 37.0 3.0 7.5 0.8 R46 KR 4680 - - P0 -. µf.0.0 4.5 37.5.0 R46 KW - - P0-3.3 µf 3.0 4.0 4.5 37.5.0 R46 KW 4330 - - P0-4.7 µf 6.0 8.5 4.5 37.5.0 R46 KW 4470 - - P0-6.8 µf 9.0 3.0 4.5 37.5.0 R46 KW 4680 - - P0-0.0 µf 0.0.0 4.5 37.5.0 R46 KW 5 - - P0 - X CLASS (IEC 60384-4) - MKP Series. mark has replaced all the following European National marks: Table IEC 60384-4 UL 44 CSA - C. No. UL 83 CSA - C. No.8 GB/T 447 04 + 5 -/+ ±5 P.70 9.05.70 9.05 certified for Approved according to IEC 60384-4 According to IEC 665 0.0/5.0.5 0.0/5.0.5/7.5 File No.V443 File CQC03899 CQC03884 (Digit 0 to ) 5 5 Note: Ammo-pack is the preferred packaging for taped version. E Series available upon request For capacitor connected in serial with main line (two - phase and three - phase net) application, please read the SHORT GUIDE TO CHOOSE THE RIGHT FILM CAPACITORS at pag. 78 and contact our Technical Service for choosing the safest solution. 09/8 5
Rated Cap. 3 Vac / 630 Vdc Rated voltage (3=3Vac) Mechanical version and packaging (Table ) Tolerance: K (±0%); M (±0%) B H L p (V/ µs) 0. µf 4.0 9.0 3.0 0.0 0.6 5 R46 3F - - N0-0.05 µf 4.0 9.0 3.0 0.0 0.6 5 R46 3F - - N0-0.0 µf 4.0 9.0 3.0 0.0 0.6 5 R46 3F 0 - - N0-0.033 µf 5.0.0 3.0 0.0 0.6 5 R46 3F 330 - - M - 0.047 µf 5.0.0 3.0 0.0 0.6 5 R46 3F 470 - - N0-0.068 µf 6.0.0 3.0 0.0 0.6 5 R46 3F 680 - - M - 0.0 µf 6.0.0 3.0 0.0 0.6 5 R46 3F 3 - - M M 0. µf 5.0.0 8.0 5.0 0.6 4 R46 3I - - 0-0.05 µf 5.0.0 8.0 5.0 0.6 4 R46 3I - - 0-0.0 µf 5.0.0 8.0 5.0 0.6 4 R46 3I 0 - - 0-0.033 µf 5.0.0 8.0 5.0 0.6 4 R46 3I 330 - - 0-0.047 µf 5.0.0 8.0 5.0 0.6 4 R46 3I 470 - - 0-0.068 µf 5.0.0 8.0 5.0 0.6 4 R46 3I 680 - - 0-0.0 µf 5.0.0 8.0 5.0 0.6 4 R46 3I 3 - - M - 0.5 µf 6.0.0 8.0 5.0 0.6 4 R46 3I 3 - - M - 0.5 µf 9.0.5 8.0 5.0 0.6 4 R46 3I 3 - - L - 0. µf 7.5 3.5 8.0 5.0 0.6 4 R46 3I 30 - - M - 0. µf 9.0.5 8.0 5.0 0.6 4 R46 3I 30 - - L - 0. µf 6.0 7.5 8.0 5.0 0.6 4 R46 3I 30 - - 0-0.33 µf 8.5 4.5 8.0 5.0 0.6 4 R46 3I 3330 - - N0-0.33 µf 0.0 6.0 8.0 5.0 0.8 4 R46 3I 3330 - - M - 0.33 µf 7.5 8.5 8.0 5.0 0.8 4 R46 3I 3330 - - 0-0.33 µf 3.0.0 8.0 5.0 0.8 4 R46 3I 3330 - - 0-0.47 µf 0.0 6.0 8.0 5.0 0.8 4 R46 3I 3470 - - N0 M 0.47 µf.0 9.0 8.0 5.0 0.8 4 R46 3I 3470 - - M - 0.56 µf.0 9.0 8.0 5.0 0.8 4 R46 3I 3560 - - N0-0.60 µf.0 9.0 8.0 5.0 0.8 4 R46 3I 36 - - N0-0.5 µf 6.0 5.0 6.5.5 0.8 R46 3N 3 - - 0-0. µf 6.0 5.0 6.5.5 0.8 R46 3N 30 - - M - 0.33 µf 6.0 5.0 6.5.5 0.8 R46 3N 3330 - - N0-0.47 µf 7.0 6.0 6.5.5 0.8 R46 3N 3470 - - N0-0.68 µf 0.0 8.5 6.5.5 0.8 R46 3N 3680 - - M -.0 µf 0.0 8.5 6.5.5 0.8 R46 3N 4 - - N M.0 µf.0 0.0 6.5.5 0.8 R46 3N 4 - - N - 0.47 µf 9.0 7.0 3.0 7.5 0.8 R46 3R 3470 - - 0-0.68 µf 9.0 7.0 3.0 7.5 0.8 R46 3R 3680 - - M -.0 µf.0 0.0 3.0 7.5 0.8 R46 3R 4 - - M -.5 µf 3.0.0 3.0 7.5 0.8 R46 3R 4 - - M -. µf 3.0 5.0 3.0 7.5 0.8 R46 3R - - M -. µf 4.0 8.0 3.0 7.5 0.8 R46 3R - - M - 3.3 µf 8.0 33.0 3.0 7.5 0.8 R46 3R 4330 - - M - 4.7 µf 8.0 33.0 3.0 7.5 0.8 R46 3R 4470 - - M - 4.7 µf.0 37.0 3.0 7.5 0.8 R46 3R 4470 - - M -.5 µf.0.0 4.5 37.5.0 R46 3W 4 - - M -. µf.0.0 4.5 37.5.0 R46 3W - - M M. µf 3.0 4.0 4.5 37.5.0 R46 3W - - M - 3.3 µf 6.0 8.5 4.5 37.5.0 R46 3W 4330 - - M - 4.7 µf 6.0 8.5 4.5 37.5.0 R46 3W 4470 - - M M 4.7 µf 9.0 3.0 4.5 37.5.0 R46 3W 4470 - - M - 6.8 µf 0.0.0 4.5 37.5.0 R46 3W 4680 - - M - 6.8 µf 4.0 44.0 4.5 37.5.0 R46 3W 4680 - - M - 0.0 µf 30.0 45.0 4.5 37.5.0 R46 3W 5 - - M - X CLASS (IEC 60384-4) - MKP Series mark has replaced all the following European National marks: Table IEC 60384-4 UL 44 CSA - C. No. UL 83 CSA - C. No.8 GB/T 447 04 + 5 -/+ ±5 Approved according to IEC 60384-4 According to IEC 665 P.70 9.05.70 9.05 File No.V443 FileCQC03899 CQC03884 0.0/5.0.5 0.0/5.0.5/7.5 (Digit 0 to ) Note: Ammo-pack is the preferred packaging for taped version. 5 5 E Series available upon request For capacitor connected in serial with main line (two - phase and three - phase net) application, please read the SHORT GUIDE TO CHOOSE THE RIGHT FILM CAPACITORS at pag. 78 and contact our Technical Service for choosing the safest solution. 53 09/8
Loose Taped X CLASS (IEC 60384-4) - MKP metallized POLYpropylene film CAPACITOR Typical applications: interference suppression and «acrossthe-line» applications. Suitable for use in situations where failure of the capacitor would not lead to danger of electric shock. p 5 p =.5 ±0.05 0.6 or 0.8* 0.8 *See size table.. GENERAL TECHNICAL DATA Dielectric: polypropylene film. Plates: metal layer deposited by evaporation under vacuum. Winding: non-inductive type. s: tinned wire. Protection: plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94 V0. Marking: Manufacturer s logo, series, capacitance, tolerance, rated voltage, capacitor class, dielectric, climatic category, passive flammability category, manufacturing date, approvals, manufacturing plant. Climatic category: /5/56 IEC 668- Operating temperature range: - to +5 C Related documents: IEC 60384-4; EN 60384-4 electrical characteristics Rated voltage (V R ): 75 Vac (/60Hz) / 560 Vdc Capacitance range: 0.0µF to µf test method and performance Endurance: Temperature: +5 C± C 0 h Voltage applied:.5 x V R +0Vac 0. s/h (d.c.)/ min Capacitance change C/C : 0% Insulation resistance: % of initial limit. Approvals IEC 60384-4 UL 44 CSA - C. No. UL 83 CSA - C. No.8 certified for File No.CA08.063 Approved according to IEC 60384-4 According to IEC 665 mark has replaced all the following European National marks: Rated Cap. NEW 5 C 75 Vac / 560 Vdc B H L p (V/ µs) 0. µf 5.0.0 3.0 0.0 0.6 5 R46 K F - - H - 0.05 µf 5.0.0 3.0 0.0 0.6 5 R46 K F - - H - 0.0 µf 5.0.0 3.0 0.0 0.6 5 R46 K F 0 - - H - 0.033 µf 5.0.0 3.0 0.0 0.6 5 R46 K F 330 - - H - 0.047 µf 6.0.0 3.0 0.0 0.6 5 R46 K F 470 - - H - 0.068 µf 6.0.0 3.0 0.0 0.6 5 R46 K F 680 - - H M 0. µf 5.0.0 8.0 5.0 0.6 4 R46 K I - - H - 0.05 µf 5.0.0 8.0 5.0 0.6 4 R46 K I - - H - 0.0 µf 5.0.0 8.0 5.0 0.6 4 R46 K I 0 - - H - 0.033 µf 5.0.0 8.0 5.0 0.6 4 R46 K I 330 - - H - 0.047 µf 5.0.0 8.0 5.0 0.6 4 R46 K I 470 - - H - 0.068 µf 5.0.0 8.0 5.0 0.6 4 R46 K I 680 - - H - 0.0 µf 6.0.0 8.0 5.0 0.6 4 R46 K I 3 - - H - 0.5 µf 6.0 7.5 8.0 5.0 0.6 4 R46 K I 3 - - H - 0.5 µf 9.0.5 8.0 5.0 0.6 4 R46 K I 3 - - H3-0.5 µf 7.5 3.5 8.0 5.0 0.6 4 R46 K I 3 - - H - 0. µf 8.5 4.5 8.0 5.0 0.6 4 R46 K I 30 - - H - 0. µf 6.0 7.5 8.0 5.0 0.6 4 R46 K I 30 - - H M 0. µf 9.0.5 8.0 5.0 0.6 4 R46 K I 30 - - H3 M 0. µf 7.5 8.5 8.0 5.0 0.8 4 R46 K I 30 - - H4-0.33 µf 0.0 6.0 8.0 5.0 0.8 4 R46 K I 3330 - - H M 0.33 µf 7.5 8.5 8.0 5.0 0.8 4 R46 K I 3330 - - H M 0.33 µf 3.0.0 8.0 5.0 0.8 4 R46 K I 3330 - - H3 M 0.47 µf.0 9.0 8.0 5.0 0.8 4 R46 K I 3470 - - H M 0.5 µf 6.0 5.0 6.5.5 0.8 R46 K N 3 - - H - 0. µf 6.0 5.0 6.5.5 0.8 R46 K N 30 - - H - 0.33 µf 7.0 6.0 6.5.5 0.8 R46 K N 3330 - - H - 0.47 µf 0.0 8.5 6.5.5 0.8 R46 K N 3470 - - H - 0.68 µf.0 0.0 6.5.5 0.8 R46 K N 3680 - - H -.0 µf 3.0.0 6.5.5 0.8 R46 K N 4 - - H - Rated voltage (K=75Vac) Mechanical version and packaging (Table ) Tolerance: K (±0%); M (±0%) 3Vac available upon request E Series available upon request For capacitor connected in serial with main line (two - phase and three - phase net) application, please read the SHORT GUIDE TO CHOOSE THE RIGHT FILM CAPACITORS at pag. 78 and contact our Technical Service for choosing the safest solution. 09/8 54
Loose Taped SVERSION X CLASS (IEC 60384-4) - MKP Series Typical applications: This special R46 release is designed for applications in series with the main. ±0.05 *See size table.. GENERAL TECHNICAL DATA Dielectric: polypropylene film. p 5.5 p 7.5 p = 37.5 0.6 or 0.8* 0.8.0 Plates: metal layer deposited by evaporation under vacuum. Winding: non-inductive type. s: tinned wire. Protection: plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94 V0. Marking: Manufacturer s logo, series, capacitance, tolerance, rated voltage, capacitor class, dielectric, climatic category, passive flammability category, manufacturing date, approvals, manufacturing plant. Climatic category: /0/56 IEC 668- Operating temperature range: - to +0 C Related documents: IEC 60384-4, EN 60384-4. electrical characteristics Rated voltage (V R ): 75Vac (/60Hz) / 560 Vdc Capacitance range: 0.0µF to 0µF Capacitance values: E6 series (IEC 663 Norm). Capacitance tolerances (measured at khz): ±0% (K); ±0% (M). tolerance ±5% (J) available upon request Dissipation factor (DF): tgδ 0-4 at +5 C ±5 C: 5 (8)* at khz * Typical value Insulation resistance: Temperature: +5 C±5 C Voltage charge time: min Voltage charge: Vdc x0 5 MΩ (5x0 5 MΩ ) * for C 0.33µF 3 s (5 s ) * for C>0.33µF * Typical value Test voltage between terminations (on all pieces): 5Vac for s + Vdc for s at +5 C±5 C Box thickness (B) imum dimensions B max H max L max 0.0 All B +0. H +0. L +0. 5.0 <7.5 B +0. H +0. L +0.3 5.0 7.5 B +0. H +0. L +0.5.5 All B +0. H +0. L +0.3 7.5 All B +0. H +0. L +0.3 37.5 All B +0.3 H +0. L +0.3 test method and performance Damp heat, steady state: st Temperature: + C ± C Relative humidity (RH): 93% ±% 56 days nd Temperature: +60 C ± C Relative humidity (RH): 95% ±% 5 hours 3rd Temperature: + C ± C Relative humidity (RH): 93% ±% 5 hours Voltage value: 30 Vac, Hz Dielectric strength: no dielectric breakdown or (d.c.)/ min Capacitance change C/C : 5% Endurance: Temperature: +0 C ± C 0 h Voltage applied:.5 x V R +0Vac 0. s/h (d.c.)/ min Capacitance change C/C : 0% Resistance to soldering heat: Solder bath temperature: +60 C ± 5 C Dipping time (with heat screen):0 s ± s Capacitance change C/C : % 55 09/8
SVERSION X CLASS (IEC60384-4) - MKP Series Rated Cap. (*) 75 Vac / 560 Vdc B H L p (V/ µs) 0. µf 5.0.0 8.0 5.0 0.6 4 R46 KI - - S0-0.05 µf 5.0.0 8.0 5.0 0.6 4 R46 KI - - S0-0.0 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 0 - - S0-0.033 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 330 - - S0-0.047 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 470 - - S - 0.068 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 680 - - S0-0.0 µf 5.0.0 8.0 5.0 0.6 4 R46 KI 3 - - S M 0.0 µf 6.0.0 8.0 5.0 0.6 4 R46 KI 3 - - S0-0.5 µf 6.0.0 8.0 5.0 0.6 4 R46 KI 3 - - S M 0.5 µf 7.5 3.5 8.0 5.0 0.6 4 R46 KI 3 - - S0-0.5 µf 9.0.5 8.0 5.0 0.6 4 R46 KI 3 - - S3-0. µf 7.5 3.5 8.0 5.0 0.6 4 R46 KI 30 - - S M 0. µf 8.5 4.5 8.0 5.0 0.6 4 R46 KI 30 - - S0-0. µf 6.0 7.5 8.0 5.0 0.6 4 R46 KI 30 - - S - 0. µf 9.0.5 8.0 5.0 0.6 4 R46 KI 30 - - S3-0.33 µf 3.0.0 8.0 5.0 0.8 4 R46 KI 3330 - - S - 0.33 µf 8.5 4.5 8.0 5.0 0.8 4 R46 KI 3330 - - S3 M 0.33 µf 0.0 6.0 8.0 5.0 0.8 4 R46 KI 3330 - - S0-0.33 µf 7.5 8.5 8.0 5.0 0.8 4 R46 KI 3330 - - S - 0.47 µf.0 9.0 8.0 5.0 0.8 4 R46 KI 3470 - - S0-0.47 µf 0.0 6.0 8.0 5.0 0.8 4 R46 KI 3470 - - S M 0.56 µf.0 9.0 8.0 5.0 0.8 4 R46 KI 3560 - - S0-0.68 µf.0 9.0 8.0 5.0 0.8 4 R46 KI 3680 - - S0 M 0. µf 6.0 5.0 6.5.5 0.8 R46 KN 30 - - S0-0.33 µf 6.0 5.0 6.5.5 0.8 R46 KN 3330 - - S M 0.33 µf 7.0 6.0 6.5.5 0.8 R46 KN 3330 - - S0-0.47 µf 7.0 6.0 6.5.5 0.8 R46 KN 3470 - - S M 0.47 µf 8.5 7.0 6.5.5 0.8 R46 KN 3470 - - S0-0.68 µf 0.0 8.5 6.5.5 0.8 R46 KN 3680 - - S0 -.0 µf 0.0 8.5 6.5.5 0.8 R46 KN 4 - - S M.0 µf.0 0.0 6.5.5 0.8 R46 KN 4 - - S -. µf 3.0.0 6.5.5 0.8 R46 KN - - S0-0.47 µf 9.0 7.0 3.0 7.5 0.8 R46 KR 3470 - - S0-0.68 µf 9.0 7.0 3.0 7.5 0.8 R46 KR 3680 - - S -.0 µf.0 0.0 3.0 7.5 0.8 R46 KR 4 - - S -.5 µf 3.0.0 3.0 7.5 0.8 R46 KR 4 - - S -. µf 3.0 5.0 3.0 7.5 0.8 R46 KR - - S - 3.3 µf 8.0 33.0 3.0 7.5 0.8 R46 KR 4330 - - S - 4.7 µf 8.0 33.0 3.0 7.5 0.8 R46 KR 4470 - - S -.5 µf.0.0 4.5 37.5.0 R46 KW 4 - - S -. µf.0.0 4.5 37.5.0 R46 KW - - S M. µf 3.0 4.0 4.5 37.5.0 R46 KW - - S - 3.3 µf 6.0 8.5 4.5 37.5.0 R46 KW 4330 - - S - 4.7 µf 6.0 8.5 4.5 37.5.0 R46 KW 4470 - - S M 4.7 µf 9.0 3.0 4.5 37.5.0 R46 KW 4470 - - S - 6.8 µf 0.0.0 4.5 37.5.0 R46 KW 4680 - - S - 0.0 µf 30.0 45.0 4.5 37.5.0 R46 KW 5 - - S - Rated voltage (K=75Vac) Mechanical version and packaging (Table ) Tolerance: K (±0%); M (±0%) Table IEC 60384-4 UL 44 CSA - C. No. UL 83 CSA - C. No.8 GB/T 447 04 + 5 -/+ ±5 certified for Approved according to IEC 60384-4 According to IEC 665 mark has replaced all the following European National marks: P.70 9.05.70 9.05 File No.V443 File CQC03899 CQC03884 0.0/5.0.5 0.0/5.0.5/7.5 (Digit 0 to ) Note: Ammo-pack is the preferred packaging for taped version. 5 5 3Vac Available upon request E Series available upon request 09/8 56
Loose Taped Insulated Insulated 0.5mm +R Capacitors with discharge resistor X CLASS (IEC 60384-4) - MKP Series Typical applications: interference suppression and «across-the-line» applications. Suitable for use in situations where failure of the capacitor would not lead to danger of electric shock. Box thickness (B) imum dimensions B max H max L max.5 All B +0. H +0. L +0.3 7.5 All B +0. H +0. L +0.3 37.5 All B +0.3 H +0. L +0.3 ±0.05. P=.5 to 7.5 p = 37.5 0.8 GENERAL TECHNICAL DATA Dielectric: polypropylene film. Plates: metal layer deposited by evaporation under vacuum. Winding: non-inductive type. s: tinned wire. Protection: plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94 V0. Marking: Manufacturer s logo, series, capacitance, tolerance, rated voltage, capacitor class, dielectric, climatic category, passive flammability category, manufacturing date, approvals, manufacturing plant. Climatic category: /0/56 IEC 668- Operating temperature range: - to +0 C Related documents: IEC 60384-4, EN 60384-4. electrical characteristics Rated voltage (V R ): 75Vac (/60Hz) / 560 Vdc 3Vac (/60Hz) / 630 Vdc Capacitance range: 0.µF to 0µF Capacitance values: E6 series (IEC 663 Norm). Capacitance tolerances (measured at khz): ±0% (K); ±0% (M). Dissipation factor (DF): tgδ 0-4 at +5 C ±5 C: 0 (6)* at khz * Typical value Insulation resistance: Temperature: +5 C±5 C Voltage charge time: min Voltage charge: Vdc x0 5 MΩ (5x0 5 MΩ ) * for C 0.33µF 3 s (5 s ) * for C>0.33µF * Typical value Test voltage between terminations (on all pieces): test method and performance Damp heat, steady state: st Temperature: + C ± C Relative humidity (RH): 93% ±% 56 days (d.c.)/ min Capacitance change C/C : 5% Endurance: Temperature: +0 C ± C 0 h Voltage applied:.5 x V R +0Vac 0. s/h (d.c.)/ min Capacitance change C/C : 0% Resistance to soldering heat: Solder bath temperature: +60 C ± 5 C Dipping time (with heat screen):0 s ± s Capacitance change C/C : % IEC 60384-4 UL 83 (30Vac-05 C) CSA - C. No.8 (30Vac-05 C) certified for Approved according to IEC 60384-4 According to IEC 665. File No.V443 57 09/8
+R Capacitors with discharge resistor X CLASS (IEC 60384-4) - MKP Series Rated Cap. (*) Rated Cap. (*) 75 Vac / 560 Vdc B H L p 3 Vac / 630 Vdc B H L p (V/ µs) (V/ µs) 0. µf 7.0 6.0 6.5.5 0.8 R46KN 30 - - 0 - x 0.33 µf 8.5 7.0 6.5.5 0.8 R46KN 3330 - - 0 - x 0.47 µf 0.0 8.5 6.5.5 0.8 R46KN 3470 - - 0 - x 0.68 µf.0 0.0 6.5.5 0.8 R46KN 3680 - - 0 - x 0.47 µf.0 0.0 3.0 7.5 0.8 R46KR 3470 - - 0 - x 0.68 µf.0 0.0 3.0 7.5 0.8 R46KR 3680 - - M - x.0 µf 3.0.0 3.0 7.5 0.8 R46KR 4 - - M - x.5 µf 3.0.0 3.0 7.5 0.8 R46KR 4 - - M - x. µf 4.0 8.0 3.0 7.5 0.8 R46KR - - M - x 3.3 µf 8.0 33.0 3.0 7.5 0.8 R46KR 4330 - - M - x 4.7 µf.0 37.0 3.0 7.5 0.8 R46KR 4470 - - M - x.5 µf.0.0 4.5 37.5.0 R46KW 4 - - M - x. µf 3.0 4.0 4.5 37.5.0 R46KW - - M - x 3.3 µf 6.0 8.5 4.5 37.5.0 R46KW 4330 - - M - x 4.7 µf 9.0 3.0 4.5 37.5.0 R46KW 4470 - - M - x 6.8 µf 0.0.0 4.5 37.5.0 R46KW 4680 - - M - x 0.0 µf 4.0 44.0 4.5 37.5.0 R46KW 5 - - M - x Rated voltage (K=75Vac) Mechanical version and packaging (Table ) Tolerance: K (±0%); M (±0%) Value of discharge resistor (Table ) 0. µf 7.0 6.0 6.5.5 0.8 R463N 30 - - 0 - x 0.33 µf 8.5 7.0 6.5.5 0.8 R463N 3330 - - 0 - x 0.47 µf 0.0 8.5 6.5.5 0.8 R463N 3470 - - 0 - x 0.68 µf.0 0.0 6.5.5 0.8 R463N 3680 - - 0 - x 0.47 µf.0 0.0 3.0 7.5 0.8 R463R 3470 - - 0 - x 0.68 µf.0 0.0 3.0 7.5 0.8 R463R 3680 - - M - x.0 µf 3.0.0 3.0 7.5 0.8 R463R 4 - - M - x.5 µf 3.0.0 3.0 7.5 0.8 R463R 4 - - M - x. µf 4.0 8.0 3.0 7.5 0.8 R463R - - M - x 3.3 µf 8.0 33.0 3.0 7.5 0.8 R463R 4330 - - M - x 4.7 µf.0 37.0 3.0 7.5 0.8 R463R 4470 - - M - x.5 µf.0.0 4.5 37.5.0 R463W 4 - - M - x. µf 3.0 4.0 4.5 37.5.0 R463W - - M - x 3.3 µf 6.0 8.5 4.5 37.5.0 R463W 4330 - - M - x 4.7 µf 9.0 3.0 4.5 37.5.0 R463W 4470 - - M - x 6.8 µf 0.0.0 4.5 37.5.0 R463W 4680 - - M - x 0.0 µf 4.0 44.0 4.5 37.5.0 R463W 5 - - M - x Rated voltage (3=3Vac) Mechanical version and packaging (Table ) Tolerance: K (±0%); M (±0%) Value of discharge resistor (Table ) Table P Product system (Digit 0 to ) 9.05.5/7.5 04 + 5 -/+ ±5 The part number, comprising 5 digits, is formed as follows: 3 4 5 6 7 8 9 0 3 4 5 R 4 6 - - Digit to 3 Series. Digit 4 a.c. rated voltage: K = 75Vac; 3 = 3Vac Digit 5 : N =.5; R = 7.5; W = 37.5 mm Digit 6 to 9 Digits 7-8 - 9 indicate the first three digits of Capacitance value and the 6th digit indicates the number of zeros that must be added to obtain the Rated Capacitance in pf. Digit 0 to Mechanical version and/or packaging (table ) Digit Identifies the dimensions and electrical characteristics. Digit 3 Internal use Digit 4 Capacitance tolerance: K=±0%; M=±0% Digit 5 Value of the discharge resistor (tolerance±0%) according to the following table*: Table R (x) 470 kω E 680 kω F MΩ G. MΩ L.5 MΩ N. MΩ P 3.3 MΩ Q 4.7 MΩ S 6.8 MΩ T 0 MΩ V 5 5 *Other resistors are avaible upon request. 09/8 58