INSULATED GATE BIPOLAR TRANSISTOR Features Low V CE(on) Non Punch Through IGBT Technology 1µs Short Circuit Capability Square RBSOA Positive V CE(on) Temperature Coefficient Maximum Junction Temperature rated at 175 C Lead-Free, RoHS Compliant Automotive Qualified * AUTOMOTIVE GRADE G C E n-channel AUIRGS3B6K AUIRGSL3B6K V CES = 6V PD - 96334 I C = 5A, T C =1 C at T J =175 C t sc > 1µs, T J =15 C V CE(on) typ. = 1.95V Benefits Benchmark Efficiency for Motor Control Rugged Transient Performance Low EMI Excellent Current Sharing in Parallel Operation D 2 Pak AUIRGS3B6K TO-262 AUIRGSL3B6K G C E Absolute Maximum Ratings Gate Collector Emitter Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only; and functional operation of the device at these or any other condition beyond those indicated in the specifications is not implied.exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Ambient temperature (T A ) is 25 C, unless otherwise specified Parameter Max. Units V CES Collector-to-Emitter Voltage 6 V I C @ T C = 25 C Continuous Collector Current 78 I C @ T C = 1 C Continuous Collector Current 5 A I CM Pulse Collector Current (Ref.Fig.C.T.5) 12 I LM Clamped Inductive Load current c 12 V ISOL RMS Isolation Voltage, Terminal to Case, t=1 min. 25 V V GE Gate-to-Emitter Voltage ±2 P D @ T C = 25 C Maximum Power Dissipation 37 W P D @ T C = 1 C Maximum Power Dissipation 18 T J Operating Junction and -55 to +175 T STG Storage Temperature Range C Soldering Temperature, for 1 sec. 3 (.63 in. (1.6mm) from case) Thermal / Mechanical Characteristics Parameter Min. Typ. Max. Units R θjc Junction-to-Case- IGBT.41* R θcs Case-to-Sink, flat, greased surface.5 C/W R θja Junction-to-Ambient (PCB Mount, Steady State)d 4 Wt Weight 1.44 g * R θjc (end of life) =.65 C/W. This is the maximum measured value after 1 temperature cycles from -55 to 15 C and is accounted for by the physical wearout of the die attach medium. www.irf.com 1 1/14/1
AUIRGS/SL3B6K Dynamic Electrical Characteristics @ T J = 25 C (unless otherwise specified) Parameter Min. Typ. Max. Units Conditions Ref.Fig. V (BR)CES Collector-to-Emitter Breakdown Voltage 6 V V GE = V, I C = 5µA V (BR)CES / T J Temperature Coeff. of Breakdown Voltage.4 V/ C V GE = V, I C = 1mA (25 C-15 C) V CE(on) Collector-to-Emitter Voltage 1.95 2.35 I C = 3A, V GE = 15V, T J = 25 C 5,6,7 2.4 2.75 V I C = 3A, V GE = 15V, T J = 15 C 8,9,1 2.6 2.95 I C = 3A, V GE = 15V, T J = 175 C V GE(th) Gate Threshold Voltage 3.5 4.5 5.5 V V CE = V GE, I C = 25µA 8,9,1 V GE(th) / T J Threshold Voltage temp. coefficient -1 mv/ C V CE = V GE, I C = 1.mA (25 C-15 C) 11 gfe Forward Transconductance 18 S V CE = 5V, I C = 5A, PW = 8µs I CES Zero Gate Voltage Collector Current 5. 25 V GE = V, V CE = 6V 1 2 µa V GE = V, V CE = 6V, T J = 15 C 183 3 V GE = V, V CE = 6V, T J = 175 C I GES Gate-to-Emitter Leakage Current ±1 na V GE = ±2V, V CE = V Static or Switching Characteristics @ T J = 25 C (unless otherwise specified) Parameter Min. Typ. Max. Units Conditions Ref.Fig. Q g Total Gate Charge (turn-on) 12 153 I C = 3A 17 Q ge Gate-to-Emitter Charge (turn-on) 14 21 nc V CC = 4V CT1 Q gc Gate-to-Collector Charge (turn-on) 44 66 V GE = 15V E on Turn-On Switching Loss 35 62 I C = 3A, V CC = 4V CT4 E off Turn-Off Switching Loss 825 955 µj V GE = 15V, R G = 1Ω, L = 2µH E tot Total Switching Loss 1175 1575 T J = 25 C e t d(on) Turn-On delay time 46 6 I C = 3A, V CC = 4V t r Rise time 28 39 ns V GE = 15V, R G = 1Ω, L = 2µH CT4 t d(off) Turn-Off delay time 185 2 T J = 25 C t f Fall time 31 4 E on Turn-On Switching Loss 635 185 I C = 3A, V CC = 4V CT4 E off Turn-Off Switching Loss 115 135 µj V GE = 15V, R G = 1Ω, L = 2µH 12,14 E tot Total Switching Loss 1785 2435 T J = 15 C e WF1,WF2 t d(on) Turn-On delay time 46 6 I C = 3A, V CC = 4V 13,15 t r Rise time 28 39 ns V GE = 15V, R G = 1Ω, L = 2µH CT4 t d(off) Turn-Off delay time 25 235 T J = 15 C WF1 t f Fall time 32 42 WF2 L E Internal Emitter Inductance 7.5 nh Measured 5mm from package C ies Input Capacitance 175 V GE = V C oes Output Capacitance 16 pf V CC = 3V 16 C res Reverse Transfer Capacitance 6 f = 1.MHz RBSOA Reverse Bias Safe Operating Area FULL SQUARE T J = 15 C, I C = 12A, Vp = 6V 4 V CC =5V,V GE = +15V to V,R G =1Ω SCSOA Short Circuit Safe Operating Area 1 µs T J = 15 C, Vp = 6V, R G = 1Ω CT3 V CC =36V,V GE = +15V to V WF3 I SC (Peak) Peak Short Circuit Collector Current 2 A WF3 CT2 Notes: V CC = 8% (V CES ), V GE = 2V, L = 28µH, R G = 22Ω. This is applied to D 2 Pak, when mounted on 1" square PCB ( FR-4 or G-1 Material ). For recommended footprint and soldering techniques refer to application note #AN-994. ƒ Energy losses include "tail" and diode reverse recovery. 2 www.irf.com
AUIRGS/SL3B6K Qualification Information Automotive (per AEC-Q11) Qualification Level Moisture Sensitivity Level Machine Model Human Body Model ESD Charged Device Model RoHS Compliant Comments: This part number(s) passed Automotive qualification. IR s Industrial and Consumer qualification level is granted by extension of the higher Automotive level. D 2 PAK MSL1 TO-262 (per IPC/JEDEC J-STD-2) N/A Class M4 (4V) AEC-Q11-2 Class H2 (4V) AEC-Q11-1 Class C4 (1V) AEC-Q11-5 Yes Qualification standards can be found at International Rectifier s web site: http://www.irf.com Exceptions to AEC-Q11 requirements are noted in the qualification report. Higher MSL ratings may be available for the specific package types listed here. Please contact your International Rectifier sales representative for further information. www.irf.com 3
I C (A) I C A) I C (A) P tot (W) AUIRGS/SL3B6K 8 7 6 5 4 3 2 1 2 4 6 8 1 12 14 16 18 T C ( C) 4 35 3 25 2 15 1 5 2 4 6 8 1 12 14 16 18 T C ( C) Fig. 1 - Maximum DC Collector Current vs. Case Temperature Fig. 2 - Power Dissipation vs. Case Temperature 1 1 1 1 µs 1 1 1 µs 1 1ms DC 1.1 1 1 1 1 1 1 1 1 1 Fig. 3 - Forward SOA T C = 25 C; T J 15 C Fig. 4 - Reverse Bias SOA T J = 15 C; V GE =15V 4 www.irf.com
I CE (A) I CE (A) I CE (A) AUIRGS/SL3B6K 6 5 4 V GE = 18V V GE = 15V V GE = 12V V GE = 1V V GE = 8.V 6 5 4 V GE = 18V V GE = 15V V GE = 12V V GE = 1V V GE = 8.V 3 3 2 2 1 1 1 2 3 4 5 1 2 3 4 5 Fig. 5 - Typ. IGBT Output Characteristics T J = -4 C; tp = 8µs Fig. 6 - Typ. IGBT Output Characteristics T J = 25 C; tp = 8µs 6 5 4 3 V GE = 18V V GE = 15V V GE = 12V V GE = 1V V GE = 8.V 2 1 1 2 3 4 5 Fig. 7 - Typ. IGBT Output Characteristics T J = 15 C; tp = 8µs www.irf.com 5
I CE (A) AUIRGS/SL3B6K 2 2 18 18 16 16 14 14 12 1 8 I CE = 15A I CE = 3A I CE = 6A 12 1 8 I CE = 15A I CE = 3A I CE = 6A 6 6 4 4 2 2 5 1 15 2 5 1 15 2 V GE (V) V GE (V) Fig. 8 - Typical V CE vs. V GE T J = -4 C Fig. 9 - Typical V CE vs. V GE T J = 25 C 2 25 18 16 2 T J = 25 C T J = 15 C 14 12 1 8 I CE = 15A I CE = 3A I CE = 6A 15 1 6 4 5 T J = 15 C 2 T J = 25 C 5 1 15 2 5 1 15 2 V GE (V) V GE (V) Fig. 1 - Typical V CE vs. V GE T J = 15 C Fig. 11 - Typ. Transfer Characteristics V CE = 5V; tp = 1µs 6 www.irf.com
Energy (µj) Swiching Time (ns) Swiching Time (ns) AUIRGS/SL3B6K 3 1 25 Energy (µj) 2 td OFF E OFF 15 1 1 E ON td ON 5 t F t R 2 4 6 8 I C (A) 1 2 4 6 8 I C (A) Fig. 12 - Typ. Energy Loss vs. I C T J = 15 C; L=2µH; V CE = 4V, R G = 1Ω; V GE = 15V Fig. 13 - Typ. Switching Time vs. I C T J = 15 C; L=2µH; V CE = 4V R G = 1Ω; V GE = 15V 3 1 25 2 E OFF 1 td OFF 15 E ON 1 1 td ON t F 5 t R 25 5 75 1 125 1 25 5 75 1 125 R G (Ω) R G (Ω) Fig. 14 - Typ. Energy Loss vs. R G T J = 15 C; L=2µH; V CE = 4V I CE = 3A; V GE = 15V Fig. 15 - Typ. Switching Time vs. R G T J = 15 C; L=2µH; V CE = 4V I CE = 3A; V GE = 15V www.irf.com 7
Capacitance (pf) V GE (V) AUIRGS/SL3B6K 1 16 1 Cies 14 12 1 2V 4V 8 1 Coes 6 4 Cres 2 1 2 4 6 8 1 25 5 75 1 125 Q G, Total Gate Charge (nc) Fig. 16- Typ. Capacitance vs. V CE V GE = V; f = 1MHz Fig. 17 - Typical Gate Charge vs. V GE I CE = 3A; L = 6µH 1 1 Thermal Response ( Z thjc ).1.1.1.1 D =.5.2.1.5.2.1 SINGLE PULSE ( THERMAL RESPONSE ) R 1 R 2 R 1 R 2 τ J τ J τ 1 τ τ 2 1 τ 2 Ci= τi/ri Ci i/ri 1E-6 1E-5.1.1.1.1 1 t 1, Rectangular Pulse Duration (sec) τ C τ Ri ( C/W) τi (sec).2.428.29.1331 Notes: 1. Duty Factor D = t1/t2 2. Peak Tj = P dm x Zthjc + Tc Fig 18. Maximum Transient Thermal Impedance, Junction-to-Case (IGBT) 8 www.irf.com
AUIRGS/SL3B6K L 1K DUT L VCC 8 V + - Rg DUT 48V Fig.C.T.1 - Gate Charge Circuit (turn-off) Fig.C.T.2 - RBSOA Circuit Driver diode clamp / DUT L DC DUT 36V - 5V Rg DUT / DRIVER VCC Fig.C.T.3 - S.C.SOA Circuit Fig.C.T.4 - Switching Loss Circuit R = VCC ICM Rg DUT VCC Fig.C.T.5 - Resistive Load Circuit www.irf.com 9
AUIRGS/SL3B6K 7 35 7 7 6 3 6 6 9% I CE 5 tf 25 5 TEST CURRENT 5 4 2 4 4 VCE (V) 3 2 1 5% V CE 5% I CE 15 1 5 ICE (A) VCE (V) 3 2 1 tr 9% test current 1% test current 5% V CE 3 2 1 ICE (A) Eoff Loss -1-5 -.2..2.4.6.8 Time(µs) Eon Loss -1-1 15.9 16. 16.1 16.2 16.3 Time (µs) Fig. WF1- Typ. Turn-off Loss Waveform @ T J = 15 C using Fig. CT.4 Fig. WF2- Typ. Turn-on Loss Waveform @ T J = 15 C using Fig. CT.4 6 3 5 25 4 I CE 2 VCE (V) 3 2 V CE 15 1 ICE (A) 1 5-5.. 5. 1. 15. time (µs) Fig. WF3- Typ. S.C Waveform @ T C = 15 C using Fig. CT.3 1 www.irf.com
TO-262 Package Outline Dimensions are shown in millimeters (inches) AUIRGS/SL3B6K TO-262 Part Marking Information Part Number IR Logo AUGSL3B6K YWWA XX or XX Date Code Y= Year WW= Work Week A= Automotive, Lead Free Lot Code Note: For the most current drawing please refer to IR website at http://www.irf.com/package/ www.irf.com 11
AUIRGS/SL3B6K D 2 Pak (TO-263AB) Package Outline Dimensions are shown in millimeters (inches) D 2 Pak (TO-263AB) Part Marking Information Part Number IR Logo AUGS3B6K YWWA XX or XX Date Code Y= Year WW= Work Week A= Automotive, Lead Free Lot Code Note: For the most current drawing please refer to IR website at http://www.irf.com/package/ 12 www.irf.com
D 2 Pak (TO-263AB) Tape & Reel Information Dimensions are shown in millimeters (inches) AUIRGS/SL3B6K TRR 1.6 (.63) 1.5 (.59) 4.1 (.161) 3.9 (.153) 1.6 (.63) 1.5 (.59).368 (.145).342 (.135) FEED DIRECTION TRL 1.85 (.73) 1.65 (.65) 1.9 (.429) 1.7 (.421) 11.6 (.457) 11.4 (.449) 16.1 (.634) 15.9 (.626) 1.75 (.69) 1.25 (.49) 15.42 (.69) 15.22 (.61) 24.3 (.957) 23.9 (.941) 4.72 (.136) 4.52 (.178) FEED DIRECTION 13.5 (.532) 12.8 (.54) 27.4 (1.79) 23.9 (.941) 4 33. (14.173) MAX. 6. (2.362) MIN. NOTES : 1. COMFORMS TO EIA-418. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION MEASURED @ HUB. 4. INCLUDES FLANGE DISTORTION @ OUTER EDGE. 26.4 (1.39) 24.4 (.961) 3 3.4 (1.197) MAX. 4 www.irf.com 13
AUIRGS/SL3B6K Ordering Information Base part number Package Type Standard Pack Complete Part Number Form Quantity AUIRGSL3B6K TO-262 Tube 5 AUIRGSL3B6K AUIRGS3B6K D2Pak Tube 5 AUIRGS3B6K Tape and Reel Left 8 AUIRGS3B6KTRL Tape and Reel Right 8 AUIRGS3B6KTRR 14 www.irf.com
AUIRGS/SL3B6K IMPORTANT NOTICE Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. Part numbers designated with the AU prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. All products are sold subject to IR s terms and conditions of sale supplied at the time of order acknowledgment. IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR s standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using IR components. To minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is not responsible or liable for any such statements. IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product. IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR products are specifically designated by IR as military-grade or enhanced plastic. Only products designated by IR as military-grade meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has not designated as military-grade is solely at the Buyer s risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation AU. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be responsible for any failure to meet such requirements For technical support, please contact IR s Technical Assistance Center http://www.irf.com/technical-info/ WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 9245 Tel: (31) 252-715 www.irf.com 15