We strive to ensure that our products are of the highest quality and free of manufacturing defects or missing parts. However, if you have any problems with your new product, D O NOT RETURN IT TO THE STORE, please contact us toll free @: FAX: 1-866-873-3531 gameroom@escaladesports.com Or write to: Escalade Sports Customer Service Department P.O. Box 889 Evansville,IN 47706 P l e a s e h a v e y o u r dat e code w h e n i n q u i r i n g a b o u t p a r t s. W h e n c o n t a c t i n g E s c a l a d e S p o r t s p l e a s e p r o v i d e y o u r m o d e l n u m b e r, date code (if a p p l i c a b l e ), a n d p a r t n u m b e r i f r e q u e s t i n g a r e p l a c e m e n t p a r t. T h e s e n u m b e r s a r e l o c a t e d o n t h e p r o d u c t, p a c k a g i n g, a n d i n t h i s o w n e r s m a n u a l. HT600 Y o u r M o d e l N u m b e r Dat e Code: 2 - HT600 - - MW Purchase Date: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 2014 E s c a l a d e S p o r t s 1 F o r C u s t o m e r S e r v i c e C a l l 1-888-996-2729
IMPORTANT! READ EACH STEP IN THIS MANUAL BEFORE YOU BEGIN THE ASSEMBLY. TWO ADULTS ARE REQUIRED TO ASSEMBLE THIS HT600 PHAZER 7.5 FT AIR HOCKEY TABLE Tools Required: T1 - Allen Wrench (Included) and T2 - Wrench (Included) Phillips Screwdriver Furniture Polish and Cloth Assembly Tips Make sure you understand the following tips before you begin to assemble your hockey table. 1. Start all bolts by hand before tightening. 2. Some drawings or images in this manual may not look exactly like your product. Please read and understand the text before starting each assembly step. READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO ADULTS ARE NEEDED TO PUT THIS HOCKEY TABLE TOGETHER.. 2
H1 = 24 pcs H2 = 24 pcs H3 = 16 pcs 1/4 x 28 mm 1/4 x 16 mm 4 mm x 50 mm Allen Head Bolt Flat Washer Phillips Round Head Screw H4 = 12 pcs 5/16 x 38 mm Allen Head Bolt H5 = 36 pcs 5/16 x 19mm Flat Washer H6 = 12 pcs 5/16 Lock Washer H7 = 12 pcs 5/16 Hex Nut H8 = 2 pcs 3/16 x 25 mm Allen Head Bolt H9 = 96 pcs 4 mm x 18 mm Phillips Round Head Screw = 54 pcs 4 mm x 12 mm Phillips Round Head Screw H11 = 24 pcs 4 mm x 44 mm Phillips Flat Head Screw H12 = 12 pcs 5/16 x 44 mm Allen Head Bolt H13 = 4 pcs 4 mm x 15 mm Phillips Round Head Screw T1 = 1 pc Allen Wrench T2 = 1 pc 12mm Wrench A1 = 4 pcs Striker A2 = 4 pcs Puck A3 = 4 pcs Felt Pad NOTE: A3 Felt Pads may already be attached to A1 Strikers.! WARNING: CHOKING HAZARD Small parts. Not for children under 3 yrs.. 3
P1 = 1 pc P2 = 4 pcs P3 = 4 pcs Air Hockey Cabinet Left Leg Panel Right Leg Panel P4 = 4 pcs Front Leg Panel P5 = 4 pcs Back Leg Panel P6 = 4 pcs Leg Bottom Board P7 = 2 pcs End Leg Panel P8 = 2 pcs End Apron NOTE: P7 End Leg Panels are packed under the table cabinet. P9 = 1 pc Side Apron P10 = 1 pc Side Apron with ON/OFF slot P11 = 12 pcs U - Plastic Bracket P12 = 12 pcs L - Plastic Bracket P13 = 4 pcs Corner Post P14 = 8 pcs Leg Panel Connecting Plate P15 = 4 pcs Leg Leveler P16 = 2 pcs Puck Catcher Hole Trim! WARNING: CHOKING HAZARD Small parts. Not for children under 3 yrs.. 4
HOME P17 = 1 pc P18 = 2 pcs P19 = 1 pc Scorer Console Lower Puck Catcher A/C Adapter with Sensor Wires P20 = 1 pc ON/OFF Switch P21 = 1 pc Metal Bracket P22 = 2 pcs Upper Puck Catcher P23 = 1 pc Junction Box P24 = 2 pcs Lighting LED Rail CONTROL LED DC 5V 350mA LED VISITOR (Factory Installed) (Factory Installed)! WARNING: CHOKING HAZARD Small parts. Not for children under 3 yrs.. 5
PARTS REQUIRED: 48 pcs - H9 Phillips Round Head Screw 1 pc - P10 Side Apron with 2 pcs - P8 End Apron ON/OFF Slot 1 pc - P9 Side Apron 12 pcs - P11 U-Plastic Bracket Note: Some parts are packed on under side of Hockey Table Main Cabinet, please carefully remove these parts before starting this assembly. STEP 1: Leave P1 Air Hockey Table Cabinet face down in carton to assemble. Install four pieces P11 U-Plastic Bracket onto two pieces P8 End Apron, one piece P9 Side Apron and one piece P10 Side Apron with ON/OFF Slot using U-Guides with four pieces H9 Screws as shown in FIGURE 1 and DETAIL A. IMPORTANT NOTE: TIGHTEN, BUT DO NOT STRIP OUT H9 SCREWS. U-Guide P9 P8 H9 FIGURE 1 P11 P10 P8 DETAIL A U-Guide P11 H9 P11 6
PARTS REQUIRED: 12 pcs - H4 Allen Head Bolt 1 pc - P1 Air Hockey Table Cabinet 24 pcs - H5 Flat Washer 1 pc - T1 Allen Wrench 12 pcs - H6 Lock Washer 1 pc - T2 12mm Wrench 12 pcs - H7 Hex Nut STEP 2: Leave P1 Air Hockey Table Cabinet face down in carton to assemble. Install P8 End Aprons and P9 / P10 Side Aprons from assembly STEP 1 using H4 Allen Head Bolts, H5 Flat Washers, H6 Lock Nuts and H7 Hex Nuts as shown in FIGURE 2 and DETAIL B. IMPORTANT NOTE: DO NOT TIGHTEN H4 BOLTS ON THIS STEP. IMPORTANT NOTE: P10 SIDE APRON WITH ON/OFF SLOT MUST CLOSE TO P23 JUNCTION BOX AS SHOWN IN FIGURE 2. DETAIL B H5 H6 H7 H4 H5 P1 Air Hockey Table Cabinet Support Brace P8 P10 H5 H6 H7 IMPORTANT NOTE: P10 Side Apron with ON/OFF Slot must close to P23 Junction Box as shown. H4 H5 P23 P9 P8 FIGURE 2 7
STEP 3: Slide P13 Corner Posts to each end of Side Apron and End Apron as shown in FIGURE 3. IMPORTANT NOTE: SLIDE P13 CORNER POSTS WITH ARROW POINTING DOWN. TIGHTEN ALL H4 BOLTS ON THIS TIME. PARTS REQUIRED: 4 pcs - P13 Corner Post P13 NOTE: Install P13 Corner Posts with arrow pointing down. FIGURE 3 8
PARTS REQUIRED: 48 pcs - H9 Phillips Round Head Screw 12 pcs - P12 L-Plastic Bracket STEP 4: With the help of another adult, Install P12 L-Plastic Brackets onto P1 Air Hockey Table Cabinet, P8 End Aprons and P9 / P10 Side Aprons using H9 Phillips Round Head Screws as shown in FIGURE 4 and DETAIL C. IMPORTANT NOTE: TIGHTEN, BUT DO NOT STRIP OUT H9 SCREWS. DETAIL C H9 1 2 P12 NOTE: Angle surface on this side. H9 P12 P8 End Aprons, P9 / P10 Side Aprons P1 Air Hockey Table Cabinet H9 Aprons P12 P1 Air Hockey Table Cabinet Underneath of Playfield. H9 P12 H9 FIGURE 4 9
PARTS REQUIRED: 18 pcs - Phillips Round Head Screw 2 pcs - P16 Puck Catcher Hole Trim 4 pcs - H13 Phillips Round Head Screw 2 pcs - P18 Lower Puck Catcher with Sensor Wires 2 pcs - P22 Upper Puck Catcher STEP 5: Secure P13 Corner Posts using Screws as shown in FIGURE 5. 1 Install P16 Puck Catcher Hole Trims using pre-drilled holes with H13 Screws as shown in FIGURE 5. 2 Install P22 Upper Puck Catchers using pre-drilled holes with Screws as shown in FIGURE 5. 3 Install P18 Lower Puck Catchers with Sensor Wires using pre-drilled holes with Screws as shown in FIGURE 5. IMPORTANT NOTE: TIGHTEN, BUT DO NOT STRIP OUT AND H13 SCREWS. Next, feed the sensor plugs from P18 through underneath support beams and connect to P23 Junction Box (factory installed) as shown in DETAIL D. P13 P18 P18 Sensor Wire CONTROL HOME LED DC 5V 350mA VISITOR LED P18 Sensor Wire 3 DETAIL D 2 P22 P23 FIGURE 5 1 H13 P16 10
PARTS REQUIRED: 24 pcs - H1 Allen Head Bolt 4 pcs - P2 Left Leg Panel 4 pcs - P5 Back Leg Panel 24 pcs - H2 Flat Washer 4 pcs - P3 Right Leg Panel 1 pc - T1 Allen Wrench 24 pcs - H11 Phillips Flat 4 pcs - P4 Front Leg Panel Head Screw STEP 6: Install one piece P2 Left Leg Panel and one piece P3 Right Leg Panel onto one piece P4 Front Leg Panel using H1 Allen Head Bolts and H2 Flat Washers as shown in FIGURE 6A. Arrow Pointing on this side H2 H1 H1 Arrow Pointing on this side H2 Arrow Pointing on this side Next, Install one piece P5 Back Leg Panel using H11 Screws as shown in FIGURE 6B. TIGHTEN, BUT DO NOT STRIP OUT H11 SCREWS. P2 P4 P3 Repeat procedure for the other legs. IMPORTANT NOTE: INSTALL P2 LEFT, P3 RIGHT, P4 FRONT AND P5 BACK LEG PANELS WITH SAME ARROW POINTING DIRECTION AS SHOWN. P4 P2 P3 H11 H11 Arrow Pointing on this side FIGURE 6A H11 H11 P5 H11 H11 FIGURE 6B 11
PARTS REQUIRED: 16 pcs - H3 Phillips Round Head Screw 4 pcs - P6 Leg Bottom Board 4 pcs - P15 Leg Leveler STEP 7: Install P6 Leg Bottom Boards onto each assembled Leg using H3 Phillips Round Head Screws as shown in FIGURE 7. IMPORTANT NOTE: TIGHTEN, BUT DO NOT STRIP OUT H3 SCREWS. Thread P15 Leg Levelers onto P6 Leg Bottom Boards as shown in FIGURE 7. P15 H3 P6 FIGURE 7 12
PARTS REQUIRED: 12 pcs - H5 Flat Washer 2 pcs - P7 End Leg Panel 32 pcs - Phillips Round Head Screw 8 pcs - P14 Leg Panel Connecting Plate 12 pcs - H12 Allen Head Bolt 1 pc - T1 Allen Wrench STEP 8: Install each Leg onto P1 Air Hockey Table Cabinet using three H12 Allen Head Bolts with three H5 Flat Washers as shown in FIGURE 8. DO NOT TIGHTEN H12 BOLTS ON THIS TIME. Repeat procedure for the other Legs. With the help of another adult, First install P14 Leg Panel Connecting Plates to P7 End Leg Panels using pre-drilled holes with Screws as shown in FIGURE 8 and DETAIL E. Next, install P14 Leg Panel Connecting Plates to the DETAIL E Legs using Screws as shown. IMPORTANT NOTE: TIGHTEN, BUT DO NOT P7 FRONT STRIP OUT SCREWS. P14 P14 P6 Make sure edge of P7 flush with edge of P6. P15 P15 P7 P15 P14 P7 FRONT P15 (Install First) (Install Second) H12 H5 P1 FIGURE 8 13
PARTS REQUIRED: 4 pcs - Phillips Round Head Screw 1 pc - P19 A/C Adaptor 1 pc - P20 ON/OFF Switch 1 pc - P21 Metal Bracket STEP 9: Install P20 ON/OFF Switch onto inside of P10 Side Apron with ON/OFF Slot using pre-drilled holes with Screws as shown in FIGURE 9. Install P20 ON/OFF Switch Socket using P21 Metal Bracket with Screws as shown in FIGURE 9. IMPORTANT NOTE: TIGHTEN, BUT DO NOT STRIP OUT SCREWS. Connect P19 A/C Adaptor to P20 ON/OFF Switch Socket and P23 Junction Box (factory installed) as shown in FIGURE 9. Connect C1 Blower Motor plug to P20 ON/OFF Switch Socket as shown in FIGURE 9. FIGURE 9 P10 Side Apron with ON/OFF Slot (non laminated side) P20 ON/OFF Switch P23 Junction Box P19 A/C Adapter CONTROL HOME LED DC 5V 350mA VISITOR LED C1 Blower Motor P21 Metal Bracket 14
THIS STEP REQUIRES FOUR OR MORE ADULTS. VERY CAREFULLY TURN THE TABLE OVER AND SET IT ON ITS LEGS. BE CAREFUL, THE TABLE IS HEAVY. PARTS REQUIRED: 2 pcs - H8 Allen Head Bolt 1 pc - P17 Scorer Console 1 pc - T1 Allen Wrench STEP 10: With the help of another adult, carefully lift and rotate table into upright position. First, feed the P17 Scorer Console plug through hole on one side of the long top apron as shown in FIGURE 10 - DETAIL F. Next, connect the P17 Scorer Console plug to P23 Junction Box as shown in FIGURE 10 - DETAIL G. Next, secure the P17 Scorer Console onto long top apron using two H8 Allen Head Bolts as shown in FIGURE 10 - DETAIL H. Use T1 Allen Wrench to tighten H8 Bolts. P17 Long Top Apron Plug H8 P23 (underneath of table) LED HOME LED CONTROL VISITOR DC 5V 350mA P17 Long Top Apron DETAIL F: P17 plug through hole on table long top apron. DETAIL G: Connect plug to P23 Junction Box. DETAIL H: Secure the P17 Scorer Console using two H8 Allen Head Bolt. FIGURE 10 15
Congratulations! You have now assembled your Hockey Table. Please note the Care and Use instructions below to ensure many years of trouble free use of your Hockey Table. CARE AND USE OF YOUR HOCKEY TABLE 1. Use only a suitable 120v AC household outlet, and insure the cord is not a trip hazard. 2. For long life and best play from your air hockey table, apply spray furniture polish to a clean cloth and wipe down the playfield with air motor running to make the pucks slide faster before first play and frequently thereafter. 3. This product is intended for I NDOOR use only. 4. DO NOT operate the motor if the cord is damaged in any way. 5. DO NOT sit, climb or lean on the table. 6. DO NOT drag the table when moving it. This will damage the legs. 7. DO NOT set drinks on the table. 8. It is suggested that this table be placed close to wall thus allowing the air motor cord to NOT be a trip hazard. Always turn air motor off when table is not in use. HOCKEY GAME RULES: 1. This game is designed to be played with two (2) players, one at each end, or with four (4) players, two at each end of the game table. 2. Flip a coin to determine who will begin play, or a face-off can be held at the center of the table. 3. Play begins when the puck is placed on the playing surface. Players must hit the puck with the strikers and attempt to shoot into the opponent s goal. 4. One point is awarded when a puck is shot into the opponent s goal. 5. Winning the game: the winning score is accomplished by being the first player to reach a predetermined score or by being the player to score the most points within a given period of time. ELECTRONIC SCORER OPERATION: POWER ON/OFF = Switch Power ON/OFF button to start or turn off the scoring unit. START = Press START button to START the game. Press START button during game will PAUSE or RESUME the game. TIME = Press TIME button to select time options 15, 10, 5 minutes or No Time Limit. SOUND ON/OFF = Switch Sound ON/OFF button to turn on or turn off the sound. NOTE: If no score has been made for 15 minutes, the scoreboard will automatically SLEEP MODE. You can turn it on again by pressing the START button. However we suggest turning the power off when the game will not be used for an extended period of time. 16
ELECTRICAL CONNECTIONS & SPARE PARTS DRAWINGS P17 - Scoring Console P20 - ON/OFF Switch To Wall Outlet P23 - Junction Box P19 - A/C Adapter DC 5V 350mA VISITOR LED CONTROL HOME LED P18 - Lower Puck Catcher with Sensor Wires P18 - Lower Puck Catcher with Sensor Wires P24 - Lighting LED Rail PRODUCT PARTS LIST Part# Description Qty Part# Description Qty HT600MWH1 1/4 x 28 mm Allen Head Bolt 24 HT600MWH2 1/4 x 16 mm Flat Washer 24 HT600MWH3 4 mm x 50 mm Phillips Round Head Screw 16 HT600MWH4 5/16 x 38 mm Allen Head Bolt 12 HT600MWH5 5/16 x 19 mm Flat Washer 36 HT600MWH6 5/16 Lock Washer 12 HT600MWH7 5/16 Hex Nut 12 HT600MWH8 3/16 x 25mm Allen Head Bolt 2 HT600MWH9 4 mm x 18 mm Phillips Round Head Screw 96 HT600MW 4 mm x 12 mm Phillips Round Head Screw 54 HT600MWH11 4 mm x 44 mm Phillips Flat Head Screw 24 HT600MWH12 5/16 x 44 mm Allen Head Bolt 12 HT600MWH13 4 mm x 15 mm Phillips Round Head Screw 4 HT600MWT1 Allen Wrench 1 HT600MWT2 Wrench 1 HT600MWA1 Striker 4 HT600MWA2 Puck 2 HT600MWA3 Felt Pad 4 HT600MWK1 Hardware Kit 1 HT600MWM1 Owner s Manual 1 HT600MWC1 Blower Motor 1 HT600MWP1 Air Hockey Cabinet (no motor) 1 HT600MWP2 Left Leg Panel 4 HT600MWP3 Right Leg Panel 4 HT600MWP4 Front Leg Panel 4 HT600MWP5 Back Leg Panel 4 HT600MWP6 Leg Bottom Board 4 HT600MWP7 End Leg Panel 2 HT600MWP8 End Apron 2 HT600MWP9 Side Apron 1 HT600MWP10 Side Apron with ON/OFF Slot 1 HT600MWP11 U-Plastic Bracket 12 HT600MWP12 L-Plastic Bracket 12 HT600MWP13 Corner Post 4 HT600MWP14 Leg Panel Connecting Plate 8 HT600MWP15 Leg Leveler 4 HT600MWP16 Puck Catcher Hole Trim 2 HT600MWP17 Scorer Console 1 HT600MWP18 MODEL: HT600 Lower Puck Catcher with Sensor Wires 2 HT600MWP19 A/C Adapter 1 HT600MWP20 ON/OFF Switch 1 HT600MWP21 Metal Bracket 1 HT600MWP22 Upper Puck Catcher 2 HT600MWP23 Junction Box 1 HT600MWP24 Lighting LED Rail 2 17
90 D A Y L I M I T E D W A R R A N T Y T h i s c u s t o m e r w a r r a n t y e x t e n d s t o t h e o r i g i n a l o w n e r, o n t h e p u r c h a s e o f a n y ESCALADE S P O R T S P r o d u c t ( h e r e i n a f t e r r e f e r r e d a s t h e " P r o d u c t "). W A R R A N T Y D U R A T I O N : T h i s P r o d u c t i s w a r r a n t e d t o t h e o r i g i n a l o w n e r, f o r a p e r i o d o f 90 d a y s f r o m t h e o r i g i n a l p u r c h a s e. W A R R A N T Y C O V E R A G E : E S C A L A D E S P O R T S w a r r a n t s t o t h e o r i g i n a l o w n e r, t h i s p r o d u c t t o b e f r e e f r o m d e f e c t s i n m a t e r i a l a n d w o r k m a n s h i p w h e n u s e d f o r t h e i n t e n d e d p u r p o s e u n d e r n o r m a l u s e a n d c o n d i t i o n s. T H I S W A R R A N T Y I S V O I D I F T H E P R O D U C T H A S B E E N D A M A G E D B Y A C C I D E N T, U N R E A S O N A B L E U S E, N E G L I G E N C E, I M P R O P E R S E R V I C E, F A I L U R E T O F O L L O W I N S T R U C T I O N S P R O V I D E D W I T H T H E P R O D U C T O R O T H E R C A U S E S N O T A R I S I N G O U T O F D E F E C T S I N M A T E R I A L A N D W O R K M A N S H I P. W A R R A N T Y R E P L A C E M E N T : D u r i n g t h e a b o v e 90 d a y w a r r a n t y p e r i o d, E S C A L A D E S P O R T S s h a l l p r o v i d e r e p l a c e m e n t c o m p o n e n t s o r r e p l a c e w i t h a c o m p a r a b l e p r o d u c t a t o u r c h o o s i n g. I f p r o d u c t i s d e f e c t i v e u n d e r n o r m a l u s e a n d p r o p e r c a r e, p l e a s e c o n t a c t o u r C u s t o m e r S e r v i c e D e p t. 1-888-996-2729 / C u s t o m e r S e r v i c e D e p t. O r W r i t e u s a t : E s c a l a d e S p o r t s, I n c. - P. O. B o x 889, E v a n s A t t n : C u s t o m e r S e r v i c e D e p t. O r E - m a i l u s a t : gameroom @ e s c a l a d e s p o r t s. c o m v i l l e, I N 47706 Other than shipping requirements, no charge will be made for such replacement of in-warranty products. W A R R A N T Y D I S C L A I M E R S : A N Y I M P L I E D W A R R A N T I E S A R I S I N G O U T O F T H I S S A L E, I N C L U D I N G B U T N O T L I M I T E D T O T H E I M P L I E D W A R R A N T I E S O F M E R C H A N T A B I L I T Y A N D F I T N E S S F O R A P A R T I C U L A R P U R P O S E, A R E L I M I T E D I N D U R A T I O N T O T H E A B O V E 90 D A Y P E R I O D. E S C A L A D E S P O R T S S H A L L N O T B E L I A B L E F O R L O S S O F U S E O F T H E P R O D U C T O R O T H E R C O N S E Q U E N T I A L O R I N C I D E N T A L C O S T S, E X P E N S E S O R D A M A G E S I N C U R R E D B Y T H E C O N S U M E R O F A N Y O T H E R U S E. S o m e s t a t e s d o n o t a l l o w t h e e x c l u s i o n o r l i m i t a t i o n o f i m p l i e d w a r r a n t i e s o r c o n s e q u e n t i a l o r i n c i d e n t a l d a m a g e s, s o t h e a b o v e l i m i t a t i o n s o r e x c l u s i o n s m a y n o t a p p l y t o y o u. L E G A L R E M E D I E S : T h i s w a r r a n t y g i v e s y o u s p e c i f i c l e g a l r i g h t s a n d y o u m a y a l s o h a v e o t h e r r i g h t s w h i c h m a y v a r y f r o m s t a t e t o s t a t e. 18