Slim Sensor CSM DS_E 1 Ideal for Workpiece Position and Original Checking The to 1 kpa model can be used for workpiece position checking. The to 1MPa model is ideal for original pressure checking. Degree of protection conforms to IEC IP. Be sure to read Safety Precautions on page. Ordering Information range / output NPN open PNP open Positive pressure to 1 MPa -1C -1B Positive pressure to 1 kpa -1C -1B Negative pressure to 1 kpa -NCB -NBB Linear output 1 to V 1
Ratings and Specifications Item Model -1C -1B -1C -1B -NCB* Power supply voltage VDC ±1% with a ripple (p-p) of % max. Current consumption ma max. type Gauge pressure Permissible pressure range to 1 MPa to 1 kpa to 1 kpa setting range to 1 MPa to 1 kpa to 1 kpa Withstand pressure MPa 9 kpa Applicable fluid Noncorrosive and nonflammable gases Repeat accuracy (/ output) Accuracy (linear output) ±% FS max. Hysteresis (linear output) Differential travel (/ output). to 1.% FS max. Linearity (linear output) Response time ms max. Linear output 1 to V with an output impedance of Ω and a permissible resistive load of 1 kω min. / output current applied voltage Residual voltage Indicator Ambient temperature Ambient humidity Temperature influence Voltage influence Insulation resistance Dielectric strength Vibration resistance Shock resistance Degree of protection NPN open 8 ma max. VDC max. * These models are negative-pressure models. PNP open NPN open PNP open NPN open -NBB* PNP open NPN:. V max. (at the load current of ma) and 1 V max. (at the load current of 8 ma) PNP: 1. V max. (at the load current of ma) and V max. (at the load current of 8 ma) Operating: 1 C to C (with no icing) Storage: C to 7 C (with no icing) Operating: % to 8% (with no condensation) ±.1% FS/ C between C and ±.% FS/ C between C and C C ±.% FS/ C max. between ±.% FS/ C max. between 1 C and C or C and C 1 C and C or C and C 1 MΩ min. (at VDC) between current carry parts and case VAC for 1 min between current carry parts and case Destruction: 1 to Hz, 1.-mm double amplitude or 1 m/s whichever is smaller, for hours each in X, Y, and Z directions Destruction: 1, m/s times each in X, Y, and Z directions IEC 9 IP inlet Rc(PT)1/8 Connection method Pre-wired (standard cable length: m) Weight (packed state) Approx. 1 g port material Zinc die-cast Accessories Instruction manual
Engineering Data (Typical) Operating Fluctuation vs. Differential Travel vs. Operating Fluctuation vs. Temperature Voltage -1C -1C -1C Operating pressure fluctuation (%FS) +1 + Differential travel (%FS) 1. 1. 1..8 Operating pressure fluctuation (% FS) +1. +.. 1. ( 1) () 1 1.. 7. Temperature (ºC) Voltage (V) Linear Voltage vs. Linear Fluctuation vs. Linearity Temperature -1C -1C Linear output fluctuation (% FS) +1 + Linearity deviation (%FS) +.8 +. 1. 8 1 8 1....8 1 (MPa) Linear Fluctuation vs. Voltage -1C 1 ( 1) () Temperature (ºC).8 7 1 Linear output fluctuation (% FS) +1 + 1. 7. Voltage (V)
Gap Measurement When checking the gap between the workpiece and the nozzle as shown in the illustration, the output of the varies with the surface roughness of the workpiece or the dimensions of the nozzle. Nozzle length Nozzle diameter Workpiece Gap Air supply Examples with -1C (Typical) Influence of Surface Roughness of Workpieces Influence of Nozzle Diameter Influence of Nozzle Length 1.-S -S Conditions Nozzle dia.: mm Nozzle length: 1 mm Air pressure: 1 kpa Conditions Nozzle dia.: 1 mm Surface roughness of workpiece: 1.-S Air pressure: 1 kpa 1 dia. Conditions Nozzle dia.: 1 mm Surface roughness of workpiece: 1.-S Air pressure: 1 kpa mm dia. 1 mm -S dia. mm 1 1 1 Gap (µm) The output varies with the surface roughness of the workpiece even though the gap is constant. The rougher the surface of the workpiece is, the more noticeable the variation of output is with a small gap. The variation rate versus gap change is not large in such cases. 1 1 1 Gap (µm) The larger the nozzle diameter is, the larger the variation rate of output versus gap change is. 1 1 1 Gap (µm) The smaller the nozzle length is, the larger the variation rate of output versus gap change is.
I/O Circuit Diagrams NPN Model Timing Charts Circuit 1,,1-1C -1C Sensor main circuit Brown + V White (/) Black (linear output) -NCB 1 Blue V PNP Model Timing Charts Circuit 1,,1-1B -1B -NBB 1 Sensor main circuit Brown + V White (/) Black (linear output) Blue V
Safety Precautions WARNING This product is not designed or rated for ensuring safety of persons. Do not use it for such purposes. Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. Mounting If the diaphragm is damaged, the Sensor will not operate properly. Do not insert a screwdriver or steel wire into the interior of the pressure-sensitive parts through the pressure port. The pressure inlet has an R (PT) 1/8 taper screw and M female screw that conforms to JIS Standards. Apply sealing tape around the female taper screw so that no pressure leakage will occur. The most-suitable wrench is 17 mm in size. Make sure that the tightening torque of the M female screw is 9.8 N m or less. Dimensions Adjustment After the pressure is set with the pressure adjuster, cover the adjuster with the rubber bushing so that no dust or any other foreign material will penetrate into the interior of the. (Unit: mm).7. 1 8. * 7 dia. 1.8 dia.. 19±.1. x. 17 Rc (PT) 1/8 Two,.-dia. holes 17. 1. 1.9 adjuster 1. *.8-dia. vinyl-insulated round cable with conductors, (Conductor cross-section:. mm, Insulator diameter: 1. mm); Standard length: m In the interest of product improvement, specifications are subject to change without notice.