The first NDS (1944) was based on allowable stress design (ASD). Copyright American Wood Council. All rights reserved.
|
|
- Derrick Banks
- 5 years ago
- Views:
Transcription
1 History ASD and LRFD with the 2005 NDS Part 1 Member Design Presented by: John Buddy Showalter, P.E. Vice President, Technology Transfer The first NDS (1944) was based on allowable stress design (ASD). ASD through 2001 NDS Load Resistance Factor Design
2 ASD and LRFD in 2005 NDS Outline Document organization Overview of LRFD Concept Chapter-by-chapter description Changes from previous editions Examples NDS 2005 and Supplement Chapters 16 Chapters 13 Appendices 14 Appendices What s changed? NDS 2005 Chapters General Requirements for Building Design 2 Design Values for Structural Members 3 Design Provisions and Equations 4 Sawn Lumber 5 Structural Glued Laminated Timber 6 Round Timber Poles and Piles 7 Prefabricated Wood I-Joists 8 Structural Composite Lumber 9 Wood Structural Panels 10 Mechanical Connections 11 Dowel-Type Fasteners 12 Split Ring and Shear Plate Connectors 13 Timber Rivets 14 Shear Walls and Diaphragms 15 Special Loading Conditions 16 Fire Design of Wood Members
3 NDS 2005 Appendices NDS 2005 Supplement 2005 A Construction and Design Practices B Load Duration C Temperature Effects D Lateral Stability of Beams E Local Stresses in Fastener Groups Important! F Design for Creep and Critical Deflection Applications G Effective Column Length H Lateral Stability of Columns I Yield Limit Equations for Connections J Solution of Hankinson Equation K Typical Dimensions for Split Ring and Shear Plate Connectors L Typical Dimensions for Standard Hex Bolts, Hex Lag Screws, Wood Screws, Common, Box, and Sinker Nails M Manufacturing Tolerances for Rivets and Steel Side Plates for Timber Rivet Connections N Appendix for Load and Resistance Factor Design (LRFD) - Mandatory Sawn Lumber Grading Agencies 2 Species Combinations 3 Section Properties 4 Design Values - Lumber and Timber -Non-North North American Sawn Lumber - Structural Glued Laminated Timber - MSR and MEL Outline Document organization Overview of LRFD Concept Chapter-by-chapter description Changes from previous editions Examples Overview of LRFD Design process Design concepts Comparison with ASD
4 Design Process Design Process Demand Capacity Load Support Conditions Geometry Materials Performance Fire Economics Aesthetics. Demand Capacity Design Concepts Serviceability Two Limit State concerns: safety against failure or collapse Serviceability (performance in service) Unfactored loads Mean (avg) material strength values
5 LRFD - Safety Property Variability Factored loads Material strength values - modified Re elative Fre equency x = mean x = standard deviation COV x = x x Load x x x SCL I-Joist Glulam MSR Lumber Visually Graded Lumber Material Property Values Statistical Model Normal Distribution Curve for Load or Resistance Statistical Model Normal Distribution Curves for Load, S, and Resistance, R Based on actual physical measurements - data sets failure
6 Statistical Model LRFD - Probability of Failure Normal Distribution Curves for Safety Function, Z f Z =f R - f S m Z = m R -m S z m z z 2 R 2 S P f = one failure expected for x number of structures t designed d and built with a given P f : 10,000, : 1,000, : 100, : 10, : 1, : : 10 LRFD - Range on LRFD Safety Design Equation Range for Wood Strength Low Typical High P f 1 : 25 1 : 63 1 : 251 Demand Capacity n Q R i=1 n
7 Allowable Stress Design What stays the same as ASD? Same basic equation format Same adjustment factors Same behavioral equations Formatted for compatibility LRFD vs. ASD What changes from ASD? Three new notations -,, and K F Design loads (factored) for safety are bigger Design loads (unfactored) for serviceability are the same Material resistance values are bigger Load Duration factor changes to Time Effect Factor
8 LRFD vs. ASD LRFD vs. ASD ASD applied stress allowable stress Theoretical safety margin applied to material stresses LRFD factored load factored resistance Load factors to account for variations in loads Member performance factor Estimated loads Design Load Adjusted Resistance Tested material strength Estimated loads Factored Design Load Factored Design Resistance Tested member resistance Design values Design values 2005 NDS LRFD Standard NDS 2005 LRFD Specification Factored Load Combinations ASCE 7-02 F = flood H = hydrostatic
9 NDS 2005 LRFD Specification tied to ASCE 7-02 Factored Load Equations: NDS 2005 LRFD Specification Format Conversion Factor K F : F ASD R N = R ASD LRFD R N = K F R ASD RASD reference strengths NDS 2005 LRFD Specification Format Conversion Factor K F : R N = K F R ASD 2005 NDS LRFD Specification Why use LRFD for wood? ease of fdesigning i with multiple l materials that use an LRFD basis (steel or concrete) more rational treatment of loads rather than penalizing material strength for unknowns on loads realize efficiencies with: multiple transient live loads extreme event loads ASD load combinations have not been maintained in deference to LRFD load combinations
10 Outline Document organization Overview of LRFD Concept Chapter-by-chapter description Changes from previous editions Examples Chapter 1 - Terminology Basic requirements for checking strength are revised to use terminology applicable to both ASD and LRFD Example: The actual bending stress or moment shall not exceed the adjusted allowable bending design value. In equation format, this takes the standard form f b F b ' allowable (typically associated with ASD) replaced by adjusted more generally applicable to either ASD or LRFD better describe applying adjustment factors to reference design values Reference design values (F b, F t, F v, F c, F c, E, E min ) are multiplied by adjustment factors to determine adjusted design values (F b ', F t ', F v ', F c ', F c ', E', E min ') Chapter 1 Design Loads references loads in accordance with minimum load standards, such as ASCE 7 02 Chapter 2 Adjustment Factors Applicable to ALL defined wood products Adjusts from reference to site conditions C D, time-dependent C M wet service C t temperature
11 Chapter 2 Adjustment Factors Wet Service Factor, C M Wet Service Conditions 30 Wood EMC % Relative Humidity % Temp 30 deg F Temp 70 deg F Temp 130 deg F Wet Service Conditions Content Wet Service Factor, C M values found in the NDS Supplement for lumber %Stre ength at 12% Moisture Moisture Content of Wood (%) Impact Strength Modulus of Elasticity Modulus of Rupture Crushing Strength
12 Chapter 3 Behavioral Equations ASD vs LRFD adjusted stresses from reference Chapter 3 Behavioral Equations Beams C L beam stability ASD F n =F n C D x adjustment factors LRFD F n = F n K F n x adjustment factors Chapter 3 Behavioral Equations Beams F be equivalence 1.20E K ' min be FbE 2 2 Rb Rb ' E NDS NDS Chapter 3 Behavioral Equations TR14 - Designing for Lateral-Torsional Stability in Wood Members Basis B i of current NDS effective length approach Summarizes equivalent uniform moment factor approach Provides comparison E min adjusted for safety for both ASD and LRFD processes
13 Application - LRFD vs. ASD Application - LRFD vs. ASD Beam Example - UDL Simply Supported DEMAND LOADS Q L LRFD A, S, I ASD Safety w f = Q w = Q Serviceability w L = Q L w L = Q L Beam Example - UDL Simply Supported Safety Limit State 1 SHEAR demand LRFD w f L 2 v K F F v A 2 3 capacity demand Prime denotes inclusion of applicable C factors except C D ASD w L 2 F v C D A 2 3 capacity Application - LRFD vs. ASD Application - LRFD vs. ASD Beam Example - UDL Simply Supported Safety Limit State 2 Beam Example - UDL Simply Supported Serviceability Limit State FLEXURE LRFD ASD DISPLACEMENT LRFD ASD w f L 2 8 b K F F b S wl 2 F b C D S 8 L 5 w L L E I L 5 w L L E I demand capacity demand capacity capacity demand capacity demand Prime denotes inclusion of applicable C factors except C D
14 Chapter 3 Behavioral Equations Columns C P column stability Chapter 3 Behavioral Equations Columns F ce equivalence F 0.822E K E ' ' min ce ce 2 2 le le d d NDS NDS E min adjusted for safety for both ASD and LRFD processes Chapter 3 Behavioral Equations E min F ce equivalence E 1.03E( (COV ))/1. 66 min E = reference MOE 1.03 = adjustment factor to convert E to a pure bending basis (shear-free) (use 1.05 for glulam) 1.66 = factor of safety COV E = coefficient of variation in MOE (NDS Appendix F) E Chapter 3 Column Equations Column Example Axial Load only Safety Limit State LRFD ASD P P P P (Q) A F c K F c C P C M C t (Q) A F c C D C P C M C t demand capacity demand capacity
15 Chapter 3 Column Equations Chapter 3 Column Equations Column Example Column Example Dead Load = 5500 lbs Live Load = lbs Normal Time Duration L = 16 ft (each direction) L P A, S, I LOADS Safety LRFD P = Q = 1.2 D L = 1.2 (5500) (31500) = lbs ASD P = Q = D + L = = lbs Ends pinned Chapter 3 Column Equations Chapter 3 Column Equations Column Example GEOMETRY Section d = 9 in b=675in 6.75 Try 6-3/4 x 9 Glulam visually graded western species, 16F-1.3E X-X Pinned end K =10 L d = 16 ft L ed = K ed L d A = 61 in 2 K ed = 1.0 Y-Y X-X L Slenderness = max b =28 Y-Y Pinned end K eb = L b = 16 ft L eb = K eb L b eb L, d ed Column Example SERVICE CONDITIONS Adjustment Factors Try 6 3/4 x 9 Glulam visually graded western species, 16F-1.3E LRFD ASD Time-dependent (normal) λ = 0.8 C D = 1.0 Wet-service (dry) C M Temperature (normal) C t C t
16 Chapter 3 Column Equations Chapter 3 Column Equations Column Example MATERIALS F c E E min c (Glulam) φ c (compression) φ s (stability) K F compression K F stability Try 6 3/4 x 9 Glulam visually graded western species, 16F-1.3E LRFD 1,550 psi 1,500,000 psi 780,000 psi / c = / s = 1.76 ASD 1,550 psi 1,500, psi 780,000 psi 0.9 Column Example CAPACITY Crushing LRFD ASD F c * = F c K F c C M C t F c * = F c C D C M C t = (1,550)(2.40)(0.8)(0.9)(1.0 all) = (1,550)(1.0)(1.0 all) = 2,678 psi = 1,550 psi P 0 = A F c * = (61)(2,678) = 163,382 lbs P 0 = A F c * = (61)(1,550) = 94,550 lbs Chapter 3 Column Equations Chapter 3 Column Equations Column Example CAPACITY LRFD ASD Buckling E min = E min K F s C M C t E min = E min C M C t F ce = (780,000)(1.76)(0.85)(1.0) = 1,166,880 psi ' 0.822Emin (Slenderness) (0.822)( ) 2 (28) = 1,223 psi 2 F ce = 780,000 psi ' 0.822Emin (Slenderness) (0.822)(780000) 2 (28) = 818 psi 2 Column Example CAPACITY c Ratios F F ce * c LRFD F F ce * c ASD = 0.46 = 0.53
17 Chapter 3 Column Equations Column Example CAPACITY LRFD ASD Chapter 3 Column Equations Column Example Axial Load only Safety Limit State C p C p FcE 1 * Fc 2c FcE 1 * Fc 2c 2 FcE * Fc = 0.43 = 0.48 c COMPRESSION LRFD ASD P P P P 57,000 lbs 69,914 lbs 37,000 lbs 45,384 lbs P = A F c* C p = (61)(2,678)(0.43) = (61) (1,146) = 69,914 lbs P = A F c * C p = (61)(1,550)(0.48) = (61)(744) ) = 45,384 lbs Load / Capacity Ratio demand capacity demand capacity Chapter 3 Behavioral Equations Tension members (tension parallel to grain) Chapter 3 Behavioral Equations wood and tension perpendicular to grain Not recommended per NDS ASD F t = F t C D x adjustment factors LRFD F t = F t K F t x adjustment factors initiators: notches moment connections hanging loads
18 Chapter 3 Behavioral Equations Combined bi-axial bending and axial compression Chapter 3 Behavioral Equations Combined bending and axial - compression Chapter 3 Behavioral Equations Bearing perpendicular to grain F c = F c C M C t C i C b (ASD) F c = F c C M C t C i C b K f c (LRFD) C b bearing area factor Chapter 4 Lumber Design values Visually graded lumber MSR / MEL Timber Decking same as NDS 2001
19 Chapter 4 Lumber Lumber adjustment factors C F - size factor C fu - flat use C i - incisingi i C T - buckling stiffness C r - repetitive member Chapter 4 Lumber Lumber adjustment factors C F - size factor C fu -flat use Chapter 4 Lumber Lumber adjustment factors C i - incising C T - buckling stiffness Chapter 4 Lumber Lumber adjustment factors C r repetitive member
20 Chapter 4 Lumber Adjustment factors C f form factor removed Why? derived from plastic deformation in small clear specimens that may not be applicable to full-size members applicability to standard wood products was limited (not allowed in poles & piles it s built into the reference design value) Chapter 4 Lumber Example F t = F t C D C F (ASD) F t = F t C F K F t (LRFD) Unincised, axially loaded tension member in normal environment Chapter 4 Finger-Jointed Lumber Widely accepted for use by IBC and IRC Interchangeable with solid sawn lumber with certain limitations: HRA/NON-HRA Moisture Load conditions Chapter 4 Finger-Jointed Lumber HRA Heat Resistant t Adhesive Designated on grade stamp Used where fire rated assemblies are required by code Exterior walls Dwelling unit separations Commercial tenant separations
21 Chapter 4 Finger-Jointed Lumber NON-HRA Adhesive not rated for heat resistance Designated on grade stamp Chapter 4 Finger-Jointed Lumber HRA marks absent? Treat same as NON-HRA? Chapter 4 Finger-Jointed Lumber Other Stamp Designations Exterior Use allowed Structural applications are not limited Must meet HRA criteria in rated assemblies Chapter 4 Finger-Jointed Lumber Other Stamp Designations STUD USE ONLY or VERT USE ONLY Limited to use where bending or tension stresses are of short duration
22 Chapter 4 Finger-Jointed Lumber Older Stamps Old grade marks Obliterated New finger-jointed grade stamps apply Chapter 5 Glued Laminated Timber Design values added to NDS Supplement Reformatted glulam radial tension values Shear values increased 10% Chapter 5 Glulam Design values F rt radial tension Chapter 5 Glulam Adjustment factors C V volume Not cumulative with C L
23 Chapter 5 Glulam Adjustment factors C c curvature Applies to F b Curved portion of bending member Not applied to straight portion of member Chapter 5 Glulam Example F c = F c C D C P (ASD) F c = F c C P K F c (LRFD) Axially loaded compression member in normal environment Chapter 6 Poles & Piles Poles - post-frame Piles - foundations Chapter 6 Poles & Piles Design values No changes from 2001 NDS
24 Chapter 6 Poles & Piles Adjustment factors LRFD provisions Chapter 6 Poles & Piles Adjustment factors C u - untreated C cs - critical section C sp -single pile Chapter 6 Poles & Piles Example F c = F c C D C sp (ASD) F c = F c C sp K F c (LRFD) Single, axial load, treated, full lateral support, normal environment Chapter 7 I-joists Design values M, V, EI, K no changes Evaluation Reports Contain proprietary design
25 Chapter 7 I-joists Adjustment factors LRFD provisions Chapter 7 I-Joists Adjustment factors C r = 1.0 revised to agree with ASTM D factor of 1.0 maintained for clarity transitioning from 2001 NDS Chapter 7 I-joists Chapter 8 Structural Composite Lumber (SCL) Example M r = M r C D (ASD) M r = M r K F b (LRFD) Full lateral l support, bending member, normal environment Design values in evaluation reports Note less variability (low COV) No changes from 2001 NDS Evaluation Reports Contain proprietary design requency Relative Fr x = mean COV x xx x = Load x SCL I-Joist Glulam MSR Lumber Visually Graded Lumber Material Property Values
26 Chapter 8 Structural Composite Lumber (SCL) Adjustment factors C V volume Not cumulative with lateral stability factor, C L Chapter 8 Structural Composite Lumber (SCL) Adjustment factors C r = 1.04 C r is different than lumber (C r lumber = 1.15) Applied to F b Chapter 8 Structural Composite Lumber (SCL) Example F b = F b C D C V (ASD) F b = F b C V K F b (LRFD) Full lateral support, bending member, normal environment Chapter 9 Wood Structural Panels (WSP) Design values obtain from an approved source F b S F t A F v t v F s F c A EI EA G v t v F c
27 Chapter 9 Wood Structural t Panels (WSP) Adjustment factors C G - grade & construction C s - panel size C M -wet service C t - temperature Chapter 9 Wood Structural t Panels (WSP) Adjustment factors C G - grade & construction Chapter 9 Wood Structural t Panels (WSP) Adjustment factors C s - panel size C M - wet service C t - temperaturet Chapter 9 Wood Structural t Panels (WSP) Example F b S = F b S C D (ASD) F b S = F b S K F b (LRFD) Non-structural t I, >24 width, loaded in bending, normal environment
28 Chapters Mechanical Connections Chapter 10 mechanical connections Chapter 11 dowel-type connectors (nails, bolts, lag/wood screws) Chapter 12 split rings and shear plates Chapter 13 timber rivets Chapter 14 Shear Walls and Diaphragms enabling language for shear wall and diaphragm design design information and values in: ANSI / AF&PA SDPWS standard Covered in Part 2 September 30 ANSI / AF&PA SDPWS WIND & SEISMIC standard references 2005 NDS Special design provisions for wind and seismic loads Values for a wide variety of panel products Future Webinar October 14 Chapter 15 Special Loading Built-up columns Revised to correct limitation on short built-up columns Each ratio shall be used to calculate a column stability factor, C P, per section and the smaller C P shall be used in determining the allowable compression design value parallel to grain, F c ', for the column. F c ' for built-up columns need not be less than F c ' for the individual laminations designed as individual solid columns per section 3.7.
29 Chapter 16 Fire Design Applies to ASD only Chapter 16 Fire (ASD) Fire resistance up to two hours Columns Beams Tension Members Combined Loading Additional special provisions for glulam Chapter 16 Fire (ASD) TR10 - Calculating the Fire Resistance of Exposed Wood Members Expands uses for large, exposed wood members Expands applicability of current methods to other EWP s (SCL) Chapter 16 Fire Superior fire performance of heavy timbers attributed to the charring effect of wood Benefits of charring an insulating char layer is formed protects the core of the section Expands use of large, exposed wood members to 2 hour fire endurance applications
30 Analog for Cross-Sectional Dimensionsi Estimating Cross-sectional Dimensions due to Charring 4-Sided Exposure (i.e. columns) b = B - 2t d = D - 2t 3-Sided Exposure (i.e. beams) b = B - 2t d = D - t 2-Sided Exposure (i.e. decking) b = B - t d = D - t where: t is the char rate of the material is the fire exposure time Model for Charring of Wood Nonlinear char model used - nominal linear char rate input. To account for rounding at corners and reduction of strength and stiffness of the heated zone, the nominal char rate values, n, are increased 20%. eff n eff = 1.2 n t where: is the effective char rate (in/hr), adjusted for exposure time, t n is the nominal linear char rate (in/hr), based on 1-hr exposure t is the exposure time (hrs) Effective Char Rates and Char Layer Thickness (for n = 1.5 inches/hour) Required Fire Effective Char Effective Char Layer Endurance Rate, eff Thickness, char (hr) (in/hr) (in) 1-Hour ½-Hour Hour
31 Design for Member Capacity Allowable Design Stress to Average Ultimate Strength Adjustment Factor where: K Dead Load + Live Load K * Allowable Design Capacity is a factor to adjust from allowable design capacity to average ultimate capacity Member Capacity Bending Moment Capacity, in-lb Tensile Capacity, lb Compression Capacity, lb Beam Buckling Capacity, lb Column Buckling Capacity, lb K Fire Design Example (ASD) Fire Design Example (ASD) Douglas fir glulam beams Span L = 18 feet Spaced at s = 6 feet Design Load q live = 100 psf q dead = 15 psf For the structural design of the beam, calculate the induced moment: Beam load: w total = s (q dead + q live ) = (6 )(15+100) Induced demand moment: M max = w total L 2 / 8 = (690)(18) 2 / 8 = 690 plf = 27,945 ft-lb Timber decking nailed to the compression edge of beams provides lateral bracing Size the beam for required bending strength for 1 hour fire duration
32 Fire Design Example (ASD) Fire Design Example (ASD) Select a 6-3/4 x 12 24F-V4 Douglas-fir glulam beam Tabulated bending stress, F b, equal to 2400 psi Calculate the design resisting moment: M = F b S s = (2371)(162) / 12= 32,009 ft-lb Calculate the beam section modulus: S s = BD 2 /6 = (6.75)(12) 2 / 6 = in 3 Calculate the adjusted allowable bending stress: Assuming: C D = 1.0, C M = 1.0, C t = 1.0, C L = 1.0, C V = 0.99 F b = F b C D C M C t (lesser of C L or C V ) = 2400(1.0)(1.0)(1.0)(0.99) = 2371 psi Structural Capacity Check: M > M max 32,009 ft-lb > 27,945 ft-lb Fire Design Example (ASD) Fire Design Example (ASD) For the fire design of the wood beam: the loading is unchanged, therefore, the maximum moment is unchanged, the fire resistance must be calculated From NDS Table , find charring depth char for 1 hour duration: Required Fire Effective Char Effective Char Layer Endurance Rate, eff Thickness, char (hr) (in/hr) (in) 1-Hour ½-Hour Hour Substitute in residual cross-section dimensions for 3-sided beam into the section modulus relation, i.e.: 3-Sided Exposure (i.e. beams) b = B - 2t d = D - t = B - 2 char = D - char Calculate charred beam section modulus exposed on 3-sides: S f = (B-2 char )(D- char ) 2 / 6 = (6.75-2(1.8))(12-1.8) 2 / 6 = 54.6 in 3
33 Fire Design Example (ASD) Calculate the adjusted allowable bending stress (some adjustment factors don t apply and may have been other than 1.0 before): F b = F b (lesser of C L or C V ) = 2400 (0.99) = 2371 psi Calculate strength resisting moment using charred cross-section: M =KF b S f = (2.85)(2371)(54.6) / 12 = 30,758 ft-lb Fire Capacity Check: M > M max 30,758 ft-lb > 27,945 ft-lb NDS 2005 Appendices Layout 2005 A Construction and Design Practices B Load Duration C Temperature Effects D Lateral Stability of Beams E Local Stresses in Fastener Groups Important! F Design for Creep and Critical Deflection Applications G Effective Column Length H Lateral Stability of Columns I Yield Limit Equations for Connections J Solution of Hankinson Equation K Typical Dimensions for Split Ring and Shear Plate Connectors L Typical Dimensions for Standard Hex Bolts, Hex Lag Screws, Wood Screws, Common, Box, and Sinker Nails M Manufacturing Tolerances for Rivets and Steel Side Plates for Timber Rivet Connections N Appendix for Load and Resistance Factor Design (LRFD) - Mandatory Appendix N new! Load and Resistance Factor Design source for new variables ASTM D5457 Standard Specification for Computing the Reference Resistance of Wood-Based Materials and Structural Connections for Load and Resistance Factor Design tabulates K F conversion factors to convert from ASD reference values (see NDS Supplement) to LRFD reference values 2005 NDS Supplement Updated to include latest reference values for: visually graded lumber and timber mechanically ygraded lumber glued laminated timber tabulates resistance factors tabulates time effect factors for load combinations listed in: ASCE 7-02 Minimum Design Loads for Buildings and Other Structures NDS clarified for cases involving hydrostatic loads (H) and for cases where H is not in combination with L, use =06 0.6
34 2005 NDS Supplement - E min E min addition for reference MOE for beam and column stability: visually graded lumber and timber mechanically graded lumber glued laminated timber Represents 5% lower exclusion shear-free E value so that design value adjustments are not part of the basic design equation for column and beam stability 2005 NDS Supplement - Lumber Visually graded dimension lumber (Table 4A) Four new species added: Alaska cedar (Alaska & Western states) Alaska Hemlock (Alaska & Western states) Alaska Yellow Cedar (Alaska only) Baldcypress 2005 NDS Supplement - Timber Visually graded timber (Table 4D) Two new species added: Alaska cedar (Alaska & Western states) Baldcypress 2005 NDS Supplement Non-north north American Species Non-north north American Species (Table 4F) Several new species added: Montane pine (South Africa) Norway Spruce (Romania and the Ukraine) Silver fir (Germany, NE France, and Switzerland) Southern pine (Misiones Argentina) Southern pine (Misiones Argentina free of heart center and medium grain density
35 2005 NDS Supplement - MSR and MEL Mechanically graded dimension lumber (Table 4C) New design values added: Table 4C Footnote 2 new G, F v,f c values for MSR and MEL Table 4C new E min values for MSR and MEL 2005 NDS Supplement - Glulam Structural glued laminated timber (Table 5A) New design values added: Table 5A new E min values added Table 5A 16F stress class revised F t, F c, G Table 5A values now match Table 5A-Expanded d values Species groups for split ring and shear plate connectors removed (NDS Table 12A values inappropriate) use G of the wood located on the face receiving the connector with NDS Table 12A assignment of species group. F v values increased for prismatic members (Footnote d revised) use of test-based shear values removing the 10% reduction used previously (AITC and APA). F v values increased for non-prismatic members unchanged (AITC and APA). Non-prismatic F rt (radial tension) for D.fir-L, and SP glulam increased slightly 2005 NDS Supplement - Glulam Structural glued laminated timber (Table 5B) New combinations added for Southern Pine with more information on slope of grain differences. F bx design values reformatted to include footnoted table adjustments for special tension laminations. F vy columns consolidated and values updated with Table 5A info. Changes from previous editions NDS is one volume!! = + +
36 2005 Wood Design Package ANSI/AF&PA NDS-2005 National Design Specification (NDS) for Wood Construction with Commentary and Supplement ANSI/AF&PA SDPWS-2005 Special Design Provisions for Wind and Seismic - with Commentary ASD/LRFD Manual for Engineered Wood Construction Manual for Engineered Wood Construction ti Most non-mandatory information contained in 2001 ASD Manual, Supplements, and Guidelines bound in one volume Manual Chapters correspond to NDS Chapters Structural Wood Design Solved Example Problems (Workbook) Solved Examples (Workbook) ASD solutions in addition to the 40 examples and solutions in the current LRFD Workbook updated to the 2005 NDS NDS 2005 Summary format changes to accommodate addition of LRFD: Revised terminology Expanded applicability of adjustment factor tables Re-format of radial tension design values Revised format of beam and column stability provisions (addition of E min property) Addition of NDS Appendix N Load and Resistance Factor Design other changes introduced in the 2005 Edition: Removal of form factor Revision of repetitive member factor for I-joists Revision of full-design value terminology Clarification of built-up column provisions
37 NDS 2005 Supplement Summary 2005 Wood Design Package changes in design value tables : E min values added for all materials F v values for prismatic glulam increased minor re-formatting updated to include latest reference values for: visually graded lumber and timber mechanically graded lumber glued laminated timber
2018 NDS Changes. National Design Specification for Wood Construction (STD120)
2018 NDS Changes National Design Specification for Wood Construction (STD120) John Buddy Showalter, P.E. Vice President, Technology Transfer American Wood Council 13847IP The American Wood Council is a
More informationBeam Design - FLOOR JOIST
Beam Design - FLOOR JOIST 1. Beam Data Load Type: Uniform Dist. Load Support: Simple Beam Beam Type: Sawn Lumber Species: Douglas Fir-Larch Grade: DF No.2 Size: 2 x 10 Design Span (L): 11.83 ft. Clear
More informationBeam Design - Awning
Beam Design - Awning 1. Beam Data Load Type: Uniform Dist. Load Support: Simple Beam Beam Type: Sawn Lumber Species: Douglas Fir-Larch Grade: DF No.2 Size: 4 x 12 Design Span (L): 21.50 ft. Clear Span:
More informationBeam Design - Pine Tree
- Pine Tree 1. Beam Data Load Type: Uniform Dist. Load Support: Simple Beam Beam Type: Sawn Lumber Species: Southern Pine Grade: SP DSS Size: 2 x 8 Design Span (L): 11.83 ft. Clear Span: 11.67 ft. Total
More informationDES140: Designing for Lateral-Torsional Stability in Wood Members
DES140: Designing for Lateral-Torsional Stability in Wood embers Welcome to the Lateral Torsional Stability ecourse. 1 Outline Lateral-Torsional Buckling Basic Concept Design ethod Examples In this ecourse,
More informationBeam Design - Trotin Project
Beam Design - Trotin Project 1. Beam Data Load Type: Uniform Dist. Load Support: Simple Beam Beam Type: Glulam Species: Western Species Grade: 24F-V4 1.8E DF/DF Size: 3.125 x 13.5 Design Span (L): 14.98
More informationSubstituting T-braces for continuous lateral braces on wood truss webs
Substituting T-braces for continuous lateral braces on wood truss webs By heryl Anderson, Frank Woeste, PE, and Donald Bender, PE Introduction W eb bracing in trusses is essential for several reasons.
More informationSection Downloads. Section Downloads. Handouts & Slides can be printed. Other documents cannot be printed Course binders are available for purchase
Level II: Section 04 Simplified Method (optional) Section Downloads Section Downloads Handouts & Slides can be printed Version.0 Other documents cannot be printed Course binders are available for purchase
More informationBeam Design - Shed Roof Back Wall Beam-S
Beam Design - Shed Roof Back Wall Beam-S 1. Beam Data Load Type: Uniform Dist. Load Support: Simple Beam Beam Type: Glulam Species: Western Species Grade: 24F-V4 1.8E DF/DF Size: 2.5 x 6 Design Span (L):
More informationWood Design. fv = shear stress fv-max = maximum shear stress Fallow = allowable stress Fb = tabular bending strength = allowable bending stress
Wood Design Notation: a = name for width dimension A = name for area Areq d-adj = area required at allowable stress when shear is adjusted to include self weight b = width of a rectangle = name for height
More informationStandard Specification for Computing Reference Resistance of Wood-Based Materials and Structural Connections for Load and Resistance Factor Design 1
Designation: Standard Specification for Computing Reference Resistance of Wood-Based Materials and Structural Connections for Load and Resistance Factor Design 1 This standard is issued under the fixed
More informationDESIGN EXAMPLES APPENDIX A
APPENDIX A DESIGN EXAMPLES Comparative Shrinkage of Sawn Timber and Glulam Beams / 499 Simple Beam Design / 500 Upside-Down Beam Analysis / 50 Tension-face Notch / 504 Compression-face Notch / 505 Sloped
More information2018 WFCM Changes. Wood Frame Construction Manual for One- and Two-Family Dwellings (STD350)
2018 WFCM Changes Wood Frame Construction Manual for One- and Two-Family Dwellings (STD350) John Buddy Showalter, P.E. Vice President, Technology Transfer American Wood Council Lori Koch, P.E. Manager,
More informationDIVISION: METALS SECTION: METAL FASTENINGS SECTION: STEEL DECKING REPORT HOLDER: PNEUTEK, INC.
ICC ES Report ICC ES () 7 () www.icc es.org Most Widely Accepted and Trusted ESR 1 Reissued /1 This report is subject to renewal /. DIVISION: METALS SECTION: METAL FASTENINGS SECTION: 1 STEEL ING REPORT
More informationSeismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design
Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design Elmer E. Marx, Alaska Department of Transportation and Public Facilities Michael Keever, California Department
More informationDesign of Beams (Unit - 8)
Design of Beams (Unit - 8) Contents Introduction Beam types Lateral stability of beams Factors affecting lateral stability Behaviour of simple and built - up beams in bending (Without vertical stiffeners)
More informationChapter 9: Column Analysis and Design
Chapter 9: Column Analysis and Design Introduction Columns are usually considered as vertical structural elements, but they can be positioned in any orientation (e.g. diagonal and horizontal compression
More informationSTRENGTH AND STIFFNESS REDUCTION OF LARGE NOTCHED BEAMS
STRENGTH AND STIFFNESS REDUCTION OF LARGE NOTCHED BEAMS By Joseph F. Murphy 1 ABSTRACT: Four large glulam beams with notches on the tension side were tested for strength and stiffness. Using either bending
More informationMechanics of Materials Primer
Mechanics of Materials rimer Notation: A = area (net = with holes, bearing = in contact, etc...) b = total width of material at a horizontal section d = diameter of a hole D = symbol for diameter E = modulus
More informationfive Mechanics of Materials 1 ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 lecture
ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 lecture five mechanics www.carttalk.com of materials Mechanics of Materials 1 Mechanics of Materials MECHANICS MATERIALS
More informationStructural Calculations For:
Structural Calculations For: Project: Address: Job No. Revision: Date: 1400 N. Vasco Rd. Livermore, CA 94551 D031014 Delta 1 - Plan Check May 8, 2015 Client: Ferreri & Blau MEMBER REPORT Roof, Typical
More informationKarbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi
Chapter 04 Structural Steel Design According to the AISC Manual 13 th Edition Analysis and Design of Compression Members By Dr. Jawad Talib Al-Nasrawi University of Karbala Department of Civil Engineering
More informationCHAPTER 5. T a = 0.03 (180) 0.75 = 1.47 sec 5.12 Steel moment frame. h n = = 260 ft. T a = (260) 0.80 = 2.39 sec. Question No.
CHAPTER 5 Question Brief Explanation No. 5.1 From Fig. IBC 1613.5(3) and (4) enlarged region 1 (ASCE 7 Fig. -3 and -4) S S = 1.5g, and S 1 = 0.6g. The g term is already factored in the equations, thus
More informationFHWA Bridge Design Guidance No. 1 Revision Date: July 21, Load Rating Evaluation of Gusset Plates in Truss Bridges
FHWA Bridge Design Guidance No. 1 Revision Date: July 21, 2008 Load Rating Evaluation of Gusset Plates in Truss Bridges By Firas I. Sheikh Ibrahim, PhD, PE Part B Gusset Plate Resistance in Accordance
More informationPresented by: Civil Engineering Academy
Presented by: Civil Engineering Academy Structural Design and Material Properties of Steel Presented by: Civil Engineering Academy Advantages 1. High strength per unit length resulting in smaller dead
More informationEntrance exam Master Course
- 1 - Guidelines for completion of test: On each page, fill in your name and your application code Each question has four answers while only one answer is correct. o Marked correct answer means 4 points
More informationFAILURE TIME OF LOADED WOODEN BEAMS DURING FIRE
FAILURE TIME OF LOADED WOODEN BEAMS DURING FIRE M. H. Do and G. S. Springer* Department of Mechanical Engineering and Applied Mechanics The University of Michigan Ann Arbor, Michigan 48109 (Received May
More informationMODULE C: COMPRESSION MEMBERS
MODULE C: COMPRESSION MEMBERS This module of CIE 428 covers the following subjects Column theory Column design per AISC Effective length Torsional and flexural-torsional buckling Built-up members READING:
More informationHELIODYNE SOLAR COLLECTOR RACK STRUCTURES FOR HELIODYNE, INC. Structural calculations. Gobi 410 at 45 degrees. for WCM HELIODYNE RACK
HELIODYNE RACK PROJECT: JOB NO: 2008-36 SHEET: DESIGNED BY: WCM DATE: CHECKED BY: SCOPE: KTD DATE: Racking Calculation Report 1 OF 1/22/2011 1/22/2011 17 Structural calculations for HELIODYNE SOLAR COLLECTOR
More informationMAXIMUM SUPERIMPOSED UNIFORM ASD LOADS, psf SINGLE SPAN DOUBLE SPAN TRIPLE SPAN GAGE
F-DEK ROOF (ASD) 1-1/2" high x 6" pitch x 36" wide SECTION PROPERTIES GAGE Wd 22 1.63 20 1.98 18 2.62 16 3.30 I D (DEFLECTION) 0.142 0.173 0.228 fy = 40 ksi Sp Sn 0.122 0.135 708 815 905 1211 1329 2365
More information10012 Creviston DR NW Gig Harbor, WA fax
C.R. Laurence Co., Inc. ATTN: Chris Hanstad 2503 East Vernon Los Angeles, CA 90058 27 March 2013 SUBJ: CRL SRS STANDOFF RAILING SYSTEM GLASS BALUSTRADE GUARDS The SRS Standoff Railing System is an engineered
More informationSection Downloads. Design Process. Design Principles Outline. Basic Design Principles. Design Process. Section 06: Design Principles.
Section Downloads Section 06: Design Principles 1 Download & Print TTT I Sec 06 Slides TTT I Sec 06 Handout Section 05 Truss Materials Design Values PS 20 Section 01 TPI 1-2007 Selection 6.4.2 Repetitive
More informationTension Members. ENCE 455 Design of Steel Structures. II. Tension Members. Introduction. Introduction (cont.)
ENCE 455 Design of Steel Structures II. Tension Members C. C. Fu, Ph.D., P.E. Civil and Environmental Engineering Department University of Maryland Tension Members Following subjects are covered: Introduction
More informationPLATE GIRDERS II. Load. Web plate Welds A Longitudinal elevation. Fig. 1 A typical Plate Girder
16 PLATE GIRDERS II 1.0 INTRODUCTION This chapter describes the current practice for the design of plate girders adopting meaningful simplifications of the equations derived in the chapter on Plate Girders
More informationGeneral Comparison between AISC LRFD and ASD
General Comparison between AISC LRFD and ASD 1 General Comparison between AISC LRFD and ASD 2 AISC ASD and LRFD AISC ASD = American Institute of Steel Construction = Allowable Stress Design AISC Ninth
More informationAllowable Design Stresses (psi)
8 0 0. 2 2 1. 2 3 2 6 w w w. a n t h o n y f o r e s t. c o m 2 Allowable Design Stresses (psi) Power Beam Section Properties and Allowable Capacities 7.0 9.0 9.2 10.9 11.6 13.6 15.6 17.5 11.1 14.1 14.5
More informationPart 1 is to be completed without notes, beam tables or a calculator. DO NOT turn Part 2 over until you have completed and turned in Part 1.
NAME CM 3505 Fall 06 Test 2 Part 1 is to be completed without notes, beam tables or a calculator. Part 2 is to be completed after turning in Part 1. DO NOT turn Part 2 over until you have completed and
More informationAPPENDIX D SUMMARY OF EXISTING SIMPLIFIED METHODS
APPENDIX D SUMMARY OF EXISTING SIMPLIFIED METHODS D-1 An extensive literature search revealed many methods for the calculation of live load distribution factors. This appendix will discuss, in detail,
More informationChapter Objectives. Design a beam to resist both bendingand shear loads
Chapter Objectives Design a beam to resist both bendingand shear loads A Bridge Deck under Bending Action Castellated Beams Post-tensioned Concrete Beam Lateral Distortion of a Beam Due to Lateral Load
More informationtwo structural analysis (statics & mechanics) APPLIED ACHITECTURAL STRUCTURES: DR. ANNE NICHOLS SPRING 2017 lecture STRUCTURAL ANALYSIS AND SYSTEMS
APPLIED ACHITECTURAL STRUCTURES: STRUCTURAL ANALYSIS AND SYSTEMS DR. ANNE NICHOLS SPRING 2017 lecture two structural analysis (statics & mechanics) Analysis 1 Structural Requirements strength serviceability
More informationKarbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi
Chapter 05 Structural Steel Design According to the AISC Manual 13 th Edition Analysis and Design of Beams By Dr. Jawad Talib Al-Nasrawi University of Karbala Department of Civil Engineering 71 Introduction
More informationTension zone applications, i.e., cable trays and strut, pipe supports, fire sprinklers Seismic and wind loading
General Information Mechanical Anchors General Information Power-Stud + SD1 Wedge Expansion Anchor Product Description The Power-Stud+ SD1 anchor is a fully threaded, torque-controlled, wedge expansion
More informationthirteen wood construction: column design ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 lecture
ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2017 leture thirteen wood onstrution: olumn design Wood Columns 1 Compression Members (revisited) designed for strength & stresses
More information*Refer to IBC Section , applicable when fall protection is required. Glass stresses are designed for a safety factor of of 4.0 (IBC ).
Architectural Railing Division C.R.Laurence Co., Inc. 2503 E Vernon Ave. Los Angeles, CA 90058 (T) 800.421.6144 (F) 800.587.7501 www.crlaurence.com 12 JAN 2011 SUBJ: TAPER-LOC SYSTEM DRY-GLAZE LAMINATED
More informationChapter 4 Seismic Design Requirements for Building Structures
Chapter 4 Seismic Design Requirements for Building Structures where: F a = 1.0 for rock sites which may be assumed if there is 10 feet of soil between the rock surface and the bottom of spread footings
More informationStructural Steelwork Eurocodes Development of A Trans-national Approach
Structural Steelwork Eurocodes Development of A Trans-national Approach Course: Eurocode Module 7 : Worked Examples Lecture 0 : Simple braced frame Contents: 1. Simple Braced Frame 1.1 Characteristic Loads
More informationExample 1 - Single Headed Anchor in Tension Away from Edges BORRADOR. Calculations and Discussion
Example 1 - Single Headed Anchor in Tension Away from Edges Check the capacity of a single anchor, 1 in. diameter, F1554 Grade 36 headed bolt with heavy-hex head installed in the top of a foundation without
More informationFailure modeling of sawn lumber with a fastener hole
ELSEVIER Finite Elements in Analysis and Design 36 (2000) 83-98 FINITE ELEMENTS IN ANALYSIS AND DESIGN www.elsevier.com/locate/finel Failure modeling of sawn lumber with a fastener hole Judsen M. Williams
More informationAccordingly, the nominal section strength [resistance] for initiation of yielding is calculated by using Equation C-C3.1.
C3 Flexural Members C3.1 Bending The nominal flexural strength [moment resistance], Mn, shall be the smallest of the values calculated for the limit states of yielding, lateral-torsional buckling and distortional
More informationSteel Post Load Analysis
Steel Post Load Analysis Scope The steel posts in 73019022, 73019024, and 73019025, are considered to be traditional building products. According to the 2015 International Building Code, this type of product
More informationStatic Bending Moment Capacity of T-Type Gusset-Plate Joints in Oriented Strandboard
ORAL PRESENTATION Static Bending Moment Capacity of T-Type Gusset-Plate Joints in Oriented Strandboard Samet Demirel 1, and Jilei Zhang 2 1 Res. Asst. Dr., Karadeniz Technical University, Trabzon Turkey;
More informationCR LAURENCE Z-SERIES GLASS CLAMPS (12/14/2012) Page 1 of Dec. 2012
CR LAURENCE Z-SERIES GLASS CLAMPS (12/14/2012) Page 1 of 19 Architectural Railing Division C.R.Laurence Co., Inc. 2503 E Vernon Ave. Los Angeles, CA 90058 (T) 800.421.6144 (F) 800.587.7501 www.crlaurence.com
More information2010 NASCC / Structures Congress Orlando, Florida May 13, 2010
2010 NASCC / Structures Congress Orlando, Florida May 13, 2010 Load Transfer in Composite Construction (Chapter I of the 2010 AISC Specification) William P. Jacobs, V Stanley D. Lindsey & Associates Atlanta,
More informationFinite Element Modelling with Plastic Hinges
01/02/2016 Marco Donà Finite Element Modelling with Plastic Hinges 1 Plastic hinge approach A plastic hinge represents a concentrated post-yield behaviour in one or more degrees of freedom. Hinges only
More informationFundamentals of Structural Design Part of Steel Structures
Fundamentals of Structural Design Part of Steel Structures Civil Engineering for Bachelors 133FSTD Teacher: Zdeněk Sokol Office number: B619 1 Syllabus of lectures 1. Introduction, history of steel structures,
More information9.5 Compression Members
9.5 Compression Members This section covers the following topics. Introduction Analysis Development of Interaction Diagram Effect of Prestressing Force 9.5.1 Introduction Prestressing is meaningful when
More informationIntroduction to Structural Member Properties
Introduction to Structural Member Properties Structural Member Properties Moment of Inertia (I): a mathematical property of a cross-section (measured in inches 4 or in 4 ) that gives important information
More informationNAME: Given Formulae: Law of Cosines: Law of Sines:
NME: Given Formulae: Law of Cosines: EXM 3 PST PROBLEMS (LESSONS 21 TO 28) 100 points Thursday, November 16, 2017, 7pm to 9:30, Room 200 You are allowed to use a calculator and drawing equipment, only.
More informationWorld Shelters. U-Dome 200. Dome Shelter. Engineering Report: Dome Structure ER October South G St., Suite 3 Arcata, CA USA
Page 1 of 30 ER-87496 World Shelters 550 South G St., Suite 3 Arcata, CA 95521 USA Telephone: +1-707-822-6600 Email: info @ worldshelters.org U-Dome 200 Dome Shelter Engineering Report: Dome Structure
More informationA METHOD OF LOAD INCREMENTS FOR THE DETERMINATION OF SECOND-ORDER LIMIT LOAD AND COLLAPSE SAFETY OF REINFORCED CONCRETE FRAMED STRUCTURES
A METHOD OF LOAD INCREMENTS FOR THE DETERMINATION OF SECOND-ORDER LIMIT LOAD AND COLLAPSE SAFETY OF REINFORCED CONCRETE FRAMED STRUCTURES Konuralp Girgin (Ph.D. Thesis, Institute of Science and Technology,
More information1 Exterior Wall Members & Accessories
JamStud Introduction Table of Contents JamStud Introduc on...1 JamStud Assembly Comparisons...2 JamStud Design Considera ons...3- JamStud Sec on Proper es...5- JamStud Non Load Bearing Design Example...7-
More informationWhere and are the factored end moments of the column and >.
11 LIMITATION OF THE SLENDERNESS RATIO----( ) 1-Nonsway (braced) frames: The ACI Code, Section 6.2.5 recommends the following limitations between short and long columns in braced (nonsway) frames: 1. The
More information(Round up to the nearest inch.)
Assignment 10 Problem 5.46 LRFD First, select the lightest weight W14 column. Use the recommended design value for K for the pinned-fixed support condition specified (ref. Commentary, Appendix 7, AISC
More informationSIMPLIFIED METHOD FOR PREDICTING DEFORMATIONS OF RC FRAMES DURING FIRE EXPOSURE
SIMPLIFIED METHOD FOR PREDICTING DEFORMATIONS OF RC FRAMES DURING FIRE EXPOSURE M.A. Youssef a, S.F. El-Fitiany a a Western University, Faculty of Engineering, London, Ontario, Canada Abstract Structural
More informationWhat Every Engineer Should Know About Structures
What Every Engineer Should Know About Structures Part C - Axial Strength of Materials by Professor Patrick L. Glon, P.E. This is a continuation of a series of courses in the area of study of physics called
More informationFailure in Flexure. Introduction to Steel Design, Tensile Steel Members Modes of Failure & Effective Areas
Introduction to Steel Design, Tensile Steel Members Modes of Failure & Effective Areas MORGAN STATE UNIVERSITY SCHOOL OF ARCHITECTURE AND PLANNING LECTURE VIII Dr. Jason E. Charalambides Failure in Flexure!
More informationSabah Shawkat Cabinet of Structural Engineering Walls carrying vertical loads should be designed as columns. Basically walls are designed in
Sabah Shawkat Cabinet of Structural Engineering 17 3.6 Shear walls Walls carrying vertical loads should be designed as columns. Basically walls are designed in the same manner as columns, but there are
More informationHuntly Christie 1/26/2018 Christie Lites 100 Carson Street Toronto, ON M8W3R9
Huntly Christie 1/26/2018 Christie Lites 100 Carson Street Toronto, ON M8W3R9 Structural Analysis for 20.5x20.5 Plated Box Truss Tables CRE Project # 16.614.01 Table of Contents for Analysis Package General
More informationThermal and mechanical modeling of thermal breaks in structural steel point transmittances
Thermal and mechanical modeling of thermal breaks in structural steel point transmittances Presented to the American Society of Mechanical Engineers Presented by: Scott Hamel P.E., Ph.D. Co-Author: Sava
More informationTHEORETICAL DESIGN OF A NAILED OR BOLTED JOINT UNDER LATERAL LOAD 1. Summary
THEORETICAL DESIGN OF A NAILED OR BOLTED JOINT UNDER LATERAL LOAD 1 BY EDWARD W. KUENZI, 2 Engineer Forest Products Laboratory,3 Forest Service U. S. Department of Agriculture Summary This report presents
More informationENCE 455 Design of Steel Structures. III. Compression Members
ENCE 455 Design of Steel Structures III. Compression Members C. C. Fu, Ph.D., P.E. Civil and Environmental Engineering Department University of Maryland Compression Members Following subjects are covered:
More information1 Exterior Wall Members & Accessories
JamStud Introduction Table of Contents JamStud Introduc on...1 JamStud Assembly Comparisons...2 JamStud Design Considera ons...3- JamStud Sec on Proper es...5- JamStud Non Load Bearing Design Example...7-
More informationε t increases from the compressioncontrolled Figure 9.15: Adjusted interaction diagram
CHAPTER NINE COLUMNS 4 b. The modified axial strength in compression is reduced to account for accidental eccentricity. The magnitude of axial force evaluated in step (a) is multiplied by 0.80 in case
More informationSERVICEABILITY LIMIT STATE DESIGN
CHAPTER 11 SERVICEABILITY LIMIT STATE DESIGN Article 49. Cracking Limit State 49.1 General considerations In the case of verifications relating to Cracking Limit State, the effects of actions comprise
More information[5] Stress and Strain
[5] Stress and Strain Page 1 of 34 [5] Stress and Strain [5.1] Internal Stress of Solids [5.2] Design of Simple Connections (will not be covered in class) [5.3] Deformation and Strain [5.4] Hooke s Law
More informationInfluence of residual stresses in the structural behavior of. tubular columns and arches. Nuno Rocha Cima Gomes
October 2014 Influence of residual stresses in the structural behavior of Abstract tubular columns and arches Nuno Rocha Cima Gomes Instituto Superior Técnico, Universidade de Lisboa, Portugal Contact:
More informationSection Downloads. Section Downloads. Handouts & Slides can be printed. Course binders are available for purchase. Download & Print. Version 2.
Level II: Section 03 Design Principles Section Downloads 2 Section Downloads Handouts & Slides can be printed Version 2.0 Course binders are available for purchase Not required Download & Print TTT II
More informationEvaluation of Flexural Stiffness for RC Beams During Fire Events
3 rd International Structural Specialty Conference 3 ième conférence internationale spécialisée sur le génie des structures Edmonton, Alberta June 6-9, 202 / 6 au 9 juin 202 Evaluation of Flexural Stiffness
More informationtwenty steel construction: columns & tension members ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS FALL 2013 lecture
ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS Cor-Ten Steel Sculpture By Richard Serra Museum of Modern Art Fort Worth, TX (AISC - Steel Structures of the Everyday) FALL 2013 lecture
More informationCompression Members. ENCE 455 Design of Steel Structures. III. Compression Members. Introduction. Compression Members (cont.)
ENCE 455 Design of Steel Structures III. Compression Members C. C. Fu, Ph.D., P.E. Civil and Environmental Engineering Department University of Maryland Compression Members Following subjects are covered:
More informationDNV DESIGN. POU_Rect - Design Report Page 1 of 11
DNV DESIGN Page 1 of 11 Details Code Details Code DNV 2.7-1 2006 with AISC 360-10 ASD Description This is the 2006 edition of the DNV Standard for Certification No 2.7-1, which defines minimum technical
More informationQUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS
QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State Hooke s law. 3. Define modular ratio,
More informationPUNCHING SHEAR CALCULATIONS 1 ACI 318; ADAPT-PT
Structural Concrete Software System TN191_PT7_punching_shear_aci_4 011505 PUNCHING SHEAR CALCULATIONS 1 ACI 318; ADAPT-PT 1. OVERVIEW Punching shear calculation applies to column-supported slabs, classified
More informationChapter 8: Bending and Shear Stresses in Beams
Chapter 8: Bending and Shear Stresses in Beams Introduction One of the earliest studies concerned with the strength and deflection of beams was conducted by Galileo Galilei. Galileo was the first to discuss
More informationDIVISION: METALS SECTION: STEEL DECKING SECTION: STEEL ROOF DECKING REPORT HOLDER: NEW MILLENNIUM BUILDING SYSTEMS, LLC
0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2657 Reissued 05/2017 This report is subject to renewal 03/2018. DIVISION: 05 00 00 METALS SECTION:
More informationQUESTION BANK DEPARTMENT: CIVIL SEMESTER: III SUBJECT CODE: CE2201 SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A
DEPARTMENT: CIVIL SUBJECT CODE: CE2201 QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State
More informationChapter. Materials. 1.1 Notations Used in This Chapter
Chapter 1 Materials 1.1 Notations Used in This Chapter A Area of concrete cross-section C s Constant depending on the type of curing C t Creep coefficient (C t = ε sp /ε i ) C u Ultimate creep coefficient
More information2018 North Carolina Residential Code Prescriptive Tables for Selection of Support Elements for Beams, Girders, and Headers: Example Problems
2018 North Carolina Residential Code Prescriptive Tables for Selection of Support Elements for Beams, Girders, and Structural Building Components Association (SBCA) August 10, 2018 SBCA is an APPROVED
More informationDesign of Reinforced Concrete Structures (II)
Design of Reinforced Concrete Structures (II) Discussion Eng. Mohammed R. Kuheil Review The thickness of one-way ribbed slabs After finding the value of total load (Dead and live loads), the elements are
More informationCAPACITY DESIGN FOR TALL BUILDINGS WITH MIXED SYSTEM
13 th World Conference on Earthquake Engineering Vancouver, B.C., Canada August 1-6, 24 Paper No. 2367 CAPACITY DESIGN FOR TALL BUILDINGS WITH MIXED SYSTEM M.UMA MAHESHWARI 1 and A.R.SANTHAKUMAR 2 SUMMARY
More informationAPPENDIX D COMPARISON OF CURVED STEEL I-GIRDER BRIDGE DESIGN SPECIFICATIONS
APPENIX COMPARISON O CURVE STEEL I-GIRER BRIGE ESIGN SPECIICATIONS (This page is intentionally left blank.) TABLE O CONTENTS LIST O IGURES... -iv LIST O TABLES... -vi 1 OBJECTIVE... -1 METHOOLOGY... -1
More informationSheathing Braced Design of Wall Studs July 2011 Update. for
Civil Engineering at JOHNS HOPKINS UNIVERSITY Sheathing Braced Design of Wall Studs July 2011 Update www.ce.jhu.edu/bschafer/sheathedwalls for AISI Committee on Framing Standards Design Methods Subcommittee
More informationServiceability Deflection calculation
Chp-6:Lecture Goals Serviceability Deflection calculation Deflection example Structural Design Profession is concerned with: Limit States Philosophy: Strength Limit State (safety-fracture, fatigue, overturning
More informationBeam Design and Deflections
Beam Design and Deflections tation: a = name for width dimension A = name for area Areq d-adj = area required at allowable stress when shear is adjusted to include self weight Aweb = area of the web of
More informationSlenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A )
Slenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A23.3-94) Slender Concrete Column Design in Sway Frame Buildings Evaluate slenderness effect for columns in a
More informationSUMMARY FOR COMPRESSION MEMBERS. Determine the factored design loads (AISC/LRFD Specification A4).
SUMMARY FOR COMPRESSION MEMBERS Columns with Pinned Supports Step 1: Step : Determine the factored design loads (AISC/LRFD Specification A4). From the column tables, determine the effective length KL using
More informationFlexure: Behavior and Nominal Strength of Beam Sections
4 5000 4000 (increased d ) (increased f (increased A s or f y ) c or b) Flexure: Behavior and Nominal Strength of Beam Sections Moment (kip-in.) 3000 2000 1000 0 0 (basic) (A s 0.5A s ) 0.0005 0.001 0.0015
More informationSupplement: Statically Indeterminate Trusses and Frames
: Statically Indeterminate Trusses and Frames Approximate Analysis - In this supplement, we consider an approximate method of solving statically indeterminate trusses and frames subjected to lateral loads
More informationCase Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed.
ARCH 631 Note Set 11 S017abn Case Study in Reinforced Concrete adapted from Simplified Design of Concrete Structures, James Ambrose, 7 th ed. Building description The building is a three-story office building
More informationDowel-bearing properties of glued laminated timber with a drift pin
Dowel-bearing properties of glued laminated timber with a drift pin Masaki, Harada 1, Tomoyuki, Hayashi 2, Masahiko, Karube 3, Kohei, Komatsu 4 ABSTRACT To investigate the accuracy of present design formulas
More information