Signals & Systems. Lecture 5 Continuous-Time Fourier Transform. Alp Ertürk
|
|
- Annice Norton
- 6 years ago
- Views:
Transcription
1 Signals & Systems Lecture 5 Continuous-Time Fourier Transform Alp Ertürk alp.erturk@kocaeli.edu.tr
2 Fourier Series Representation of Continuous-Time Periodic Signals Synthesis equation: x t = a k e jkω 0t = a k e jk 2π/T 0 t Analysis equation: a k = 1 T T x(t)e jkω 0t dt = 1 T T x(t)e jk 2π/T 0 t dt
3 Limit of the Fourier Series Consider the finite-duration signal x(t) that is not periodic We cannot represent x(t) with a Fourier series However, we can use x(t) to define one period of a periodic function as long as the period is longer than the duration of x(t) An aperiodic signal can be viewed as a periodic signal with an infinite period
4 Limit of the Fourier Series Note that as the period increases, fundamental frequency decreases and the harmonically related frequencies become closer in frequency As the period becomes infinite, the frequency components form a continuum and the Fourier series sum becomes an integral
5 Limit of the Fourier Series
6 Limit of the Fourier Series Consider the finite-duration rectangular pulse given by: x t = 1 t < T 1 0 T 1 < t < T 2 = u t + T 1 u t T 1
7 Limit of the Fourier Series The Fourier coefficients of the periodic form of this square wave are: a k = 2 sin kω 0T 1 kω 0 T = 2 sin k 2π T T 1 k 2π T T An envelope can be obtained by multiplying by T and denoting ω = kω 0 : Ta k = 2 sin ωt 1 ω
8 Limit of the Fourier Series T = 4T 1 T = 8T 1 T = 16T 1
9 Consider a signal x(t) that has finite duration. That is x(t) = 0 if t > T 1 We can construct a signal x(t) for which x(t) is one period
10 a k = 1 T T x(t)e jkω 0t dt T/2 = 1 x(t)e jkω0t dt T T/2 = 1 T/2 x(t)e jkω0t dt = 1 x(t)e jkω0t dt T T/2 T X jω = Ta k = x(t)e jkω 0t dt
11 x t = a k e jkω 0t = 1 T X jkω 0 e jkω 0t Since ω 0 = 2π T = 1 2π X jkω 0 e jkω 0t ω 0
12 X jω = x(t)e jkω 0t dt x t = 1 2π X jkω 0 e jkω 0t ω 0 As T, ω 0 0, x t approaches x(t) and the right-hand side of the equation above becomes an integral Therefore,
13 Inverse Continuous-Time Fourier Transform: x(t) = 1 2π X jω e jωt dω Forward Continuous-Time Fourier Transform: X jω = x(t)e jωt dt
14 These equations were derived for an arbitrary signal with finite-duration But the equations remain valid for an extremely broad class of signals of infinite duration The set of conditions for these equations to be valid are similar to the convergence rules we covered in Fourier series
15 Dirichlet conditions: 1) x(t) must be absolutely integrable, that is: x(t) dt < 2) x(t) must have a finite number of maxima and minima within any finite interval 3) x(t) must have a finite number of discontinuities within any finite interval. Furthermore, each of these discontinuities must be finite
16 Example: Find the Fourier Transform of x t = e 7t u(t) X jω = = 0 e 7t u(t)e jωt dt e 7t e jωt dt = e 7t e jωt (7 + jω) 0 = 1 (7 + jω)
17 Example: Fourier Transform of x t = e at u t, a > 0 X jω = e at u(t)e jωt dt = 1 (a + jω), a > 0 X jω = 1 a 2 + ω 2, X jω = tan 1 ω a
18 X jω = 1 a 2 + ω 2, X jω = tan 1 ω a
19 X jω = 1 a 2 + ω 2, X jω = tan 1 ω a
20 Example: Fourier Transform of x t = e a t, a > 0 X jω = e a t e jωt dt = 0 e at e jωt dt + 0 e at e jωt dt = 1 (a jω) + 1 (a + jω) = 2a a 2 + ω 2
21
22
23 Example: Fourier Transform of x t = δ t X jω = δ t e jωt dt = 1
24 Example: Inverse Fourier Transform of X jω = 2πδ ω x(t) = 1 2π 2πδ ω e jωt dω = 1
25 Example: Fourier Transform of x t = 1, t < T 1 0, t > T 1 X jω = x(t) e jωt dt = T 1 e jωt dt T 1 = 2 sin ωt 1 ω
26
27
28 Example: Find the signal whose Fourier transform is: X jω = 1, ω < W 0, ω > W x(t) = 1 2π = 1 W 2π W X jω e jωt dω e jωt dω = sin(wt) πt
29
30
31 For a periodic signal, the Fourier transform can be directly constructed from its Fourier series representation The resulting transform consists of a train of impulses in the frequency domain The areas of the impulses proportional to the Fourier series coefficients
32 Consider a Fourier transform that is a single impulse of area 2π Then, X jω = 2πδ(ω ω 0 ) x(t) = 1 2π 2πδ(ω ω 0 )e jωt dω = e jω 0t
33 If X jω is of the form of a linear combination of impulses equally spaced in frequency, that is, Then, X jω = 2πa k δ(ω kω 0 ) k= x(t) = a k e jkω 0t k= Hence, the Fourier transform of a periodic signal with Fourier series coefficients a k can be interpreted as a train of impulses occurring at harmonically related frequencies
34 Example: Consider a periodic square wave, one period of which is given by x t = 1 t < T 1 0 T 1 < t < T 2
35 The Fourier series coefficients for this signals are: a k = 2 sin kω 0T 1 kω 0 T = sin kω 0T 1 πk Then, X jω = k= 2π sin kω 0T 1 πk δ(ω kω 0 )
36 X jω = 2 sin kω0 T 1 k= k δ(ω kω 0 )
37 Example: x t = sin ω 0 t a 1 = 1 2j, a 1 = 1 2j a k = 0, if k 1 or 1 X jω = 2π 1 2j δ ω ω 0 1 2j δ(ω + ω 0)
38
39 Example: x t = k= δ(t kt) T/2 a k = 1 δ t e jkω0t dt = 1 T T/2 T X jω = k= 2π 1 T δ(ω kω 0) = 2π T k= δ ω 2πk T
40
41 Inverse Continuous-Time Fourier Transform: x(t) = 1 2π X jω e jωt dω (Forward) Continuous-Time Fourier Transform: X jω = x(t)e jωt dt
Fourier transform representation of CT aperiodic signals Section 4.1
Fourier transform representation of CT aperiodic signals Section 4. A large class of aperiodic CT signals can be represented by the CT Fourier transform (CTFT). The (CT) Fourier transform (or spectrum)
More informationChapter 4 The Fourier Series and Fourier Transform
Chapter 4 The Fourier Series and Fourier Transform Fourier Series Representation of Periodic Signals Let x(t) be a CT periodic signal with period T, i.e., xt ( + T) = xt ( ), t R Example: the rectangular
More informationChapter 4 The Fourier Series and Fourier Transform
Chapter 4 The Fourier Series and Fourier Transform Representation of Signals in Terms of Frequency Components Consider the CT signal defined by N xt () = Acos( ω t+ θ ), t k = 1 k k k The frequencies `present
More informationSignals & Systems. Lecture 4 Fourier Series Properties & Discrete-Time Fourier Series. Alp Ertürk
Signals & Systems Lecture 4 Fourier Series Properties & Discrete-Time Fourier Series Alp Ertürk alp.erturk@kocaeli.edu.tr Fourier Series Representation of Continuous-Time Periodic Signals Synthesis equation:
More informationSignals and Systems Spring 2004 Lecture #9
Signals and Systems Spring 2004 Lecture #9 (3/4/04). The convolution Property of the CTFT 2. Frequency Response and LTI Systems Revisited 3. Multiplication Property and Parseval s Relation 4. The DT Fourier
More informationECE 3084 QUIZ 2 SCHOOL OF ELECTRICAL AND COMPUTER ENGINEERING GEORGIA INSTITUTE OF TECHNOLOGY APRIL 2, Name:
ECE 3084 QUIZ 2 SCHOOL OF ELECTRICAL AND COMPUTER ENGINEERING GEORGIA INSTITUTE OF TECHNOLOGY APRIL 2, 205 Name:. The quiz is closed book, except for one 2-sided sheet of handwritten notes. 2. Turn off
More informationChapter 6 THE SAMPLING PROCESS 6.1 Introduction 6.2 Fourier Transform Revisited
Chapter 6 THE SAMPLING PROCESS 6.1 Introduction 6.2 Fourier Transform Revisited Copyright c 2005 Andreas Antoniou Victoria, BC, Canada Email: aantoniou@ieee.org July 14, 2018 Frame # 1 Slide # 1 A. Antoniou
More informationChap 4. Sampling of Continuous-Time Signals
Digital Signal Processing Chap 4. Sampling of Continuous-Time Signals Chang-Su Kim Digital Processing of Continuous-Time Signals Digital processing of a CT signal involves three basic steps 1. Conversion
More informationReview of Fourier Transform
Review of Fourier Transform Fourier series works for periodic signals only. What s about aperiodic signals? This is very large & important class of signals Aperiodic signal can be considered as periodic
More informationThe Continuous-time Fourier
The Continuous-time Fourier Transform Rui Wang, Assistant professor Dept. of Information and Communication Tongji University it Email: ruiwang@tongji.edu.cn Outline Representation of Aperiodic signals:
More informationChapter 5 Frequency Domain Analysis of Systems
Chapter 5 Frequency Domain Analysis of Systems CT, LTI Systems Consider the following CT LTI system: xt () ht () yt () Assumption: the impulse response h(t) is absolutely integrable, i.e., ht ( ) dt< (this
More informationFourier series for continuous and discrete time signals
8-9 Signals and Systems Fall 5 Fourier series for continuous and discrete time signals The road to Fourier : Two weeks ago you saw that if we give a complex exponential as an input to a system, the output
More informationLine Spectra and their Applications
In [ ]: cd matlab pwd Line Spectra and their Applications Scope and Background Reading This session concludes our introduction to Fourier Series. Last time (http://nbviewer.jupyter.org/github/cpjobling/eg-47-
More informationCh 4: The Continuous-Time Fourier Transform
Ch 4: The Continuous-Time Fourier Transform Fourier Transform of x(t) Inverse Fourier Transform jt X ( j) x ( t ) e dt jt x ( t ) X ( j) e d 2 Ghulam Muhammad, King Saud University Continuous-time aperiodic
More informationDiscrete Time Fourier Transform
Discrete Time Fourier Transform Recall that we wrote the sampled signal x s (t) = x(kt)δ(t kt). We calculate its Fourier Transform. We do the following: Ex. Find the Continuous Time Fourier Transform of
More informationChapter 5 Frequency Domain Analysis of Systems
Chapter 5 Frequency Domain Analysis of Systems CT, LTI Systems Consider the following CT LTI system: xt () ht () yt () Assumption: the impulse response h(t) is absolutely integrable, i.e., ht ( ) dt< (this
More informationHomework 7 Solution EE235, Spring Find the Fourier transform of the following signals using tables: te t u(t) h(t) = sin(2πt)e t u(t) (2)
Homework 7 Solution EE35, Spring. Find the Fourier transform of the following signals using tables: (a) te t u(t) h(t) H(jω) te t u(t) ( + jω) (b) sin(πt)e t u(t) h(t) sin(πt)e t u(t) () h(t) ( ejπt e
More informationLECTURE 12 Sections Introduction to the Fourier series of periodic signals
Signals and Systems I Wednesday, February 11, 29 LECURE 12 Sections 3.1-3.3 Introduction to the Fourier series of periodic signals Chapter 3: Fourier Series of periodic signals 3. Introduction 3.1 Historical
More information16.362: Signals and Systems: 1.0
16.362: Signals and Systems: 1.0 Prof. K. Chandra ECE, UMASS Lowell September 1, 2016 1 Background The pre-requisites for this course are Calculus II and Differential Equations. A basic understanding of
More informationTable 1: Properties of the Continuous-Time Fourier Series. Property Periodic Signal Fourier Series Coefficients
able : Properties of the Continuous-ime Fourier Series x(t = e jkω0t = = x(te jkω0t dt = e jk(/t x(te jk(/t dt Property Periodic Signal Fourier Series Coefficients x(t y(t } Periodic with period and fundamental
More informationFourier transforms. Definition F(ω) = - should know these! f(t).e -jωt.dt. ω = 2πf. other definitions exist. f(t) = - F(ω).e jωt.
Fourier transforms This is intended to be a practical exposition, not fully mathematically rigorous ref The Fourier Transform and its Applications R. Bracewell (McGraw Hill) Definition F(ω) = - f(t).e
More informationHomework 4. May An LTI system has an input, x(t) and output y(t) related through the equation y(t) = t e (t t ) x(t 2)dt
Homework 4 May 2017 1. An LTI system has an input, x(t) and output y(t) related through the equation y(t) = t e (t t ) x(t 2)dt Determine the impulse response of the system. Rewriting as y(t) = t e (t
More informationECE 301. Division 2, Fall 2006 Instructor: Mimi Boutin Midterm Examination 3
ECE 30 Division 2, Fall 2006 Instructor: Mimi Boutin Midterm Examination 3 Instructions:. Wait for the BEGIN signal before opening this booklet. In the meantime, read the instructions below and fill out
More informationX. Chen More on Sampling
X. Chen More on Sampling 9 More on Sampling 9.1 Notations denotes the sampling time in second. Ω s = 2π/ and Ω s /2 are, respectively, the sampling frequency and Nyquist frequency in rad/sec. Ω and ω denote,
More informationCore Concepts Review. Orthogonality of Complex Sinusoids Consider two (possibly non-harmonic) complex sinusoids
Overview of Continuous-Time Fourier Transform Topics Definition Compare & contrast with Laplace transform Conditions for existence Relationship to LTI systems Examples Ideal lowpass filters Relationship
More informationThen r (t) can be expanded into a linear combination of the complex exponential signals ( e j2π(kf 0)t ) k= as. c k e j2π(kf0)t + c k e j2π(kf 0)t
.3 ourier Series Definition.37. Exponential ourier series: Let the real or complex signal r t be a periodic signal with period. Suppose the following Dirichlet conditions are satisfied: a r t is absolutely
More information4 The Continuous Time Fourier Transform
96 4 The Continuous Time ourier Transform ourier (or frequency domain) analysis turns out to be a tool of even greater usefulness Extension of ourier series representation to aperiodic signals oundation
More informationWavenumber-Frequency Space
Wavenumber-Frequency Space ECE 6279: Spatial Array Processing Spring 2011 Lecture 3 Prof. Aaron D. Lanterman School of Electrical & Computer Engineering Georgia Institute of Technology AL: 404-385-2548
More informationEE 3054: Signals, Systems, and Transforms Summer It is observed of some continuous-time LTI system that the input signal.
EE 34: Signals, Systems, and Transforms Summer 7 Test No notes, closed book. Show your work. Simplify your answers. 3. It is observed of some continuous-time LTI system that the input signal = 3 u(t) produces
More informationFourier Representations of Signals & LTI Systems
3. Introduction. A signal can be represented as a weighted superposition of complex sinusoids. x(t) or x[n] 2. LTI system: LTI System Output = A weighted superposition of the system response to each complex
More informationSeries FOURIER SERIES. Graham S McDonald. A self-contained Tutorial Module for learning the technique of Fourier series analysis
Series FOURIER SERIES Graham S McDonald A self-contained Tutorial Module for learning the technique of Fourier series analysis Table of contents Begin Tutorial c 24 g.s.mcdonald@salford.ac.uk 1. Theory
More informationTable 1: Properties of the Continuous-Time Fourier Series. Property Periodic Signal Fourier Series Coefficients
able : Properties of the Continuous-ime Fourier Series x(t = a k e jkω0t = a k = x(te jkω0t dt = a k e jk(/t x(te jk(/t dt Property Periodic Signal Fourier Series Coefficients x(t y(t } Periodic with period
More informationEA2.3 - Electronics 2 1
In the previous lecture, I talked about the idea of complex frequency s, where s = σ + jω. Using such concept of complex frequency allows us to analyse signals and systems with better generality. In this
More informationSignal and systems. Linear Systems. Luigi Palopoli. Signal and systems p. 1/5
Signal and systems p. 1/5 Signal and systems Linear Systems Luigi Palopoli palopoli@dit.unitn.it Wrap-Up Signal and systems p. 2/5 Signal and systems p. 3/5 Fourier Series We have see that is a signal
More informationEE Homework 13 - Solutions
EE3054 - Homework 3 - Solutions. (a) The Laplace transform of e t u(t) is s+. The pole of the Laplace transform is at which lies in the left half plane. Hence, the Fourier transform is simply the Laplace
More informationSIGNALS AND SYSTEMS: PAPER 3C1 HANDOUT 6. Dr Anil Kokaram Electronic and Electrical Engineering Dept.
SIGNALS AND SYSTEMS: PAPER 3C HANDOUT 6. Dr Anil Kokaram Electronic and Electrical Engineering Dept. anil.kokaram@tcd.ie www.mee.tcd.ie/ sigmedia FOURIER ANALYSIS Have seen how the behaviour of systems
More information06EC44-Signals and System Chapter Fourier Representation for four Signal Classes
Chapter 5.1 Fourier Representation for four Signal Classes 5.1.1Mathematical Development of Fourier Transform If the period is stretched without limit, the periodic signal no longer remains periodic but
More informationEC Signals and Systems
UNIT I CLASSIFICATION OF SIGNALS AND SYSTEMS Continuous time signals (CT signals), discrete time signals (DT signals) Step, Ramp, Pulse, Impulse, Exponential 1. Define Unit Impulse Signal [M/J 1], [M/J
More informationDiscrete-time Fourier transform (DTFT) representation of DT aperiodic signals Section The (DT) Fourier transform (or spectrum) of x[n] is
Discrete-time Fourier transform (DTFT) representation of DT aperiodic signals Section 5. 3 The (DT) Fourier transform (or spectrum) of x[n] is X ( e jω) = n= x[n]e jωn x[n] can be reconstructed from its
More informationFourier series: Additional notes
Fourier series: Additional notes Linking Fourier series representations for signals Rectangular waveform Require FS expansion of signal y(t) below: 1 y(t) 1 4 4 8 12 t (seconds) Period T = 8, so ω = 2π/T
More information6.003 Homework #10 Solutions
6.3 Homework # Solutions Problems. DT Fourier Series Determine the Fourier Series coefficients for each of the following DT signals, which are periodic in N = 8. x [n] / n x [n] n x 3 [n] n x 4 [n] / n
More informationHomework 6 EE235, Spring 2011
Homework 6 EE235, Spring 211 1. Fourier Series. Determine w and the non-zero Fourier series coefficients for the following functions: (a 2 cos(3πt + sin(1πt + π 3 w π e j3πt + e j3πt + 1 j2 [ej(1πt+ π
More information6.003: Signals and Systems. CT Fourier Transform
6.003: Signals and Systems CT Fourier Transform April 8, 200 CT Fourier Transform Representing signals by their frequency content. X(jω)= x(t)e jωt dt ( analysis equation) x(t)= X(jω)e jωt dω ( synthesis
More informationECE 301 Division 1, Fall 2008 Instructor: Mimi Boutin Final Examination Instructions:
ECE 30 Division, all 2008 Instructor: Mimi Boutin inal Examination Instructions:. Wait for the BEGIN signal before opening this booklet. In the meantime, read the instructions below and fill out the requested
More informationSignals and Systems I Have Known and Loved. (Lecture notes for CSE 3451) Andrew W. Eckford
Signals and Systems I Have Known and Loved (Lecture notes for CSE 3451) Andrew W. Eckford Department of Electrical Engineering and Computer Science York University, Toronto, Ontario, Canada Version: December
More information4.3 Analysis of Non-periodic Con6nuous-Time Signals. We view this non-periodic signal as a periodic signal with period as infinite large.
We view this non-periodic signal as a periodic signal with period as infinite large. For periodic signal: c k = 1 T 0 T 0 /2 T 0 /2 x(t)e jkω 0t dt For non-periodic signal: we make T 0 -> c k T 0 = T 0
More informationLecture 7 ELE 301: Signals and Systems
Lecture 7 ELE 30: Signals and Systems Prof. Paul Cuff Princeton University Fall 20-2 Cuff (Lecture 7) ELE 30: Signals and Systems Fall 20-2 / 22 Introduction to Fourier Transforms Fourier transform as
More informationECE 301. Division 3, Fall 2007 Instructor: Mimi Boutin Midterm Examination 3
ECE 30 Division 3, all 2007 Instructor: Mimi Boutin Midterm Examination 3 Instructions:. Wait for the BEGIN signal before opening this booklet. In the meantime, read the instructions below and fill out
More informationMEDE2500 Tutorial Nov-7
(updated 2016-Nov-4,7:40pm) MEDE2500 (2016-2017) Tutorial 3 MEDE2500 Tutorial 3 2016-Nov-7 Content 1. The Dirac Delta Function, singularity functions, even and odd functions 2. The sampling process and
More information6.003: Signals and Systems. CT Fourier Transform
6.003: Signals and Systems CT Fourier Transform April 8, 200 CT Fourier Transform Representing signals by their frequency content. X(jω)= x(t)e jωt dt ( analysis equation) x(t)= 2π X(jω)e jωt dω ( synthesis
More informationSpectral Analysis of Random Processes
Spectral Analysis of Random Processes Spectral Analysis of Random Processes Generally, all properties of a random process should be defined by averaging over the ensemble of realizations. Generally, all
More informationSinc Functions. Continuous-Time Rectangular Pulse
Sinc Functions The Cooper Union Department of Electrical Engineering ECE114 Digital Signal Processing Lecture Notes: Sinc Functions and Sampling Theory October 7, 2011 A rectangular pulse in time/frequency
More informationFourier series. XE31EO2 - Pavel Máša. Electrical Circuits 2 Lecture1. XE31EO2 - Pavel Máša - Fourier Series
Fourier series Electrical Circuits Lecture - Fourier Series Filtr RLC defibrillator MOTIVATION WHAT WE CAN'T EXPLAIN YET Source voltage rectangular waveform Resistor voltage sinusoidal waveform - Fourier
More informationGeorge Mason University Signals and Systems I Spring 2016
George Mason University Signals and Systems I Spring 206 Problem Set #6 Assigned: March, 206 Due Date: March 5, 206 Reading: This problem set is on Fourier series representations of periodic signals. The
More informationLecture 28 Continuous-Time Fourier Transform 2
Lecture 28 Continuous-Time Fourier Transform 2 Fundamentals of Digital Signal Processing Spring, 2012 Wei-Ta Chu 2012/6/14 1 Limit of the Fourier Series Rewrite (11.9) and (11.10) as As, the fundamental
More informationECE 301 Fall 2011 Division 1 Homework 10 Solutions. { 1, for 0.5 t 0.5 x(t) = 0, for 0.5 < t 1
ECE 3 Fall Division Homework Solutions Problem. Reconstruction of a continuous-time signal from its samples. Let x be a periodic continuous-time signal with period, such that {, for.5 t.5 x(t) =, for.5
More informationHomework: 4.50 & 4.51 of the attachment Tutorial Problems: 7.41, 7.44, 7.47, Signals & Systems Sampling P1
Homework: 4.50 & 4.51 of the attachment Tutorial Problems: 7.41, 7.44, 7.47, 7.49 Signals & Systems Sampling P1 Undersampling & Aliasing Undersampling: insufficient sampling frequency ω s < 2ω M Perfect
More informationLecture 13: Discrete Time Fourier Transform (DTFT)
Lecture 13: Discrete Time Fourier Transform (DTFT) ECE 401: Signal and Image Analysis University of Illinois 3/9/2017 1 Sampled Systems Review 2 DTFT and Convolution 3 Inverse DTFT 4 Ideal Lowpass Filter
More informationHomework 5 EE235, Summer 2013 Solution
Homework 5 EE235, Summer 23 Solution. Fourier Series. Determine w and the non-zero Fourier series coefficients for the following functions: (a f(t 2 cos(3πt + sin(πt + π 3 w π f(t e j3πt + e j3πt + j2
More informationHomework 3 Solutions
EECS Signals & Systems University of California, Berkeley: Fall 7 Ramchandran September, 7 Homework 3 Solutions (Send your grades to ee.gsi@gmail.com. Check the course website for details) Review Problem
More informationEE 224 Signals and Systems I Review 1/10
EE 224 Signals and Systems I Review 1/10 Class Contents Signals and Systems Continuous-Time and Discrete-Time Time-Domain and Frequency Domain (all these dimensions are tightly coupled) SIGNALS SYSTEMS
More informationDiscrete Time Fourier Transform (DTFT)
Discrete Time Fourier Transform (DTFT) 1 Discrete Time Fourier Transform (DTFT) The DTFT is the Fourier transform of choice for analyzing infinite-length signals and systems Useful for conceptual, pencil-and-paper
More information-Digital Signal Processing- FIR Filter Design. Lecture May-16
-Digital Signal Processing- FIR Filter Design Lecture-17 24-May-16 FIR Filter Design! FIR filters can also be designed from a frequency response specification.! The equivalent sampled impulse response
More informationDiscrete-time Signals and Systems in
Discrete-time Signals and Systems in the Frequency Domain Chapter 3, Sections 3.1-39 3.9 Chapter 4, Sections 4.8-4.9 Dr. Iyad Jafar Outline Introduction The Continuous-Time FourierTransform (CTFT) The
More information27. The Fourier Transform in optics, II
27. The Fourier Transform in optics, II Parseval s Theorem The Shift theorem Convolutions and the Convolution Theorem Autocorrelations and the Autocorrelation Theorem The Shah Function in optics The Fourier
More informationIntroduction to Fourier Transforms. Lecture 7 ELE 301: Signals and Systems. Fourier Series. Rect Example
Introduction to Fourier ransforms Lecture 7 ELE 3: Signals and Systems Fourier transform as a limit of the Fourier series Inverse Fourier transform: he Fourier integral theorem Prof. Paul Cuff Princeton
More informationVer 3808 E1.10 Fourier Series and Transforms (2014) E1.10 Fourier Series and Transforms. Problem Sheet 1 (Lecture 1)
Ver 88 E. Fourier Series and Transforms 4 Key: [A] easy... [E]hard Questions from RBH textbook: 4., 4.8. E. Fourier Series and Transforms Problem Sheet Lecture. [B] Using the geometric progression formula,
More informationFilter Analysis and Design
Filter Analysis and Design Butterworth Filters Butterworth filters have a transfer function whose squared magnitude has the form H a ( jω ) 2 = 1 ( ) 2n. 1+ ω / ω c * M. J. Roberts - All Rights Reserved
More informationNAME: 11 December 2013 Digital Signal Processing I Final Exam Fall Cover Sheet
NAME: December Digital Signal Processing I Final Exam Fall Cover Sheet Test Duration: minutes. Open Book but Closed Notes. Three 8.5 x crib sheets allowed Calculators NOT allowed. This test contains four
More information2.161 Signal Processing: Continuous and Discrete
MI OpenCourseWare http://ocw.mit.edu.6 Signal Processing: Continuous and Discrete Fall 8 For information about citing these materials or our erms of Use, visit: http://ocw.mit.edu/terms. MASSACHUSES INSIUE
More informationFourier Analysis Overview (0B)
CTFS: Continuous Time Fourier Series CTFT: Continuous Time Fourier Transform DTFS: Fourier Series DTFT: Fourier Transform DFT: Discrete Fourier Transform Copyright (c) 2009-2016 Young W. Lim. Permission
More informationECE 301 Division 1 Final Exam Solutions, 12/12/2011, 3:20-5:20pm in PHYS 114.
ECE 301 Division 1 Final Exam Solutions, 12/12/2011, 3:20-5:20pm in PHYS 114. The exam for both sections of ECE 301 is conducted in the same room, but the problems are completely different. Your ID will
More information2A1H Time-Frequency Analysis II Bugs/queries to HT 2011 For hints and answers visit dwm/courses/2tf
Time-Frequency Analysis II (HT 20) 2AH 2AH Time-Frequency Analysis II Bugs/queries to david.murray@eng.ox.ac.uk HT 20 For hints and answers visit www.robots.ox.ac.uk/ dwm/courses/2tf David Murray. A periodic
More informationCH.4 Continuous-Time Fourier Series
CH.4 Continuous-Time Fourier Series First step to Fourier analysis. My mathematical model is killing me! The difference between mathematicians and engineers is mathematicians develop mathematical tools
More informationCircuit Analysis Using Fourier and Laplace Transforms
EE2015: Electrical Circuits and Networks Nagendra Krishnapura https://wwweeiitmacin/ nagendra/ Department of Electrical Engineering Indian Institute of Technology, Madras Chennai, 600036, India July-November
More information( ) ( ) numerically using the DFT. The DTFT is defined. [ ]e. [ ] = x n. [ ]e j 2π Fn and the DFT is defined by X k. [ ]e j 2π kn/n with N = 5.
( /13) in the Ω form. ind the DTT of 8rect 3 n 2 8rect ( 3( n 2) /13) 40drcl(,5)e j 4π Let = Ω / 2π. Then 8rect 3 n 2 40 drcl( Ω / 2π,5)e j 2Ω ( /13) ind the DTT of 8rect 3( n 2) /13 by X = x n numerically
More informationReview of Discrete-Time System
Review of Discrete-Time System Electrical & Computer Engineering University of Maryland, College Park Acknowledgment: ENEE630 slides were based on class notes developed by Profs. K.J. Ray Liu and Min Wu.
More informationECE 301 Fall 2010 Division 2 Homework 10 Solutions. { 1, if 2n t < 2n + 1, for any integer n, x(t) = 0, if 2n 1 t < 2n, for any integer n.
ECE 3 Fall Division Homework Solutions Problem. Reconstruction of a continuous-time signal from its samples. Consider the following periodic signal, depicted below: {, if n t < n +, for any integer n,
More informationa k cos kω 0 t + b k sin kω 0 t (1) k=1
MOAC worksheet Fourier series, Fourier transform, & Sampling Working through the following exercises you will glean a quick overview/review of a few essential ideas that you will need in the moac course.
More informationDSP-I DSP-I DSP-I DSP-I
NOTES FOR 8-79 LECTURES 3 and 4 Introduction to Discrete-Time Fourier Transforms (DTFTs Distributed: September 8, 2005 Notes: This handout contains in brief outline form the lecture notes used for 8-79
More informationReview of Analog Signal Analysis
Review of Analog Signal Analysis Chapter Intended Learning Outcomes: (i) Review of Fourier series which is used to analyze continuous-time periodic signals (ii) Review of Fourier transform which is used
More informationSolutions to Problems in Chapter 4
Solutions to Problems in Chapter 4 Problems with Solutions Problem 4. Fourier Series of the Output Voltage of an Ideal Full-Wave Diode Bridge Rectifier he nonlinear circuit in Figure 4. is a full-wave
More informationECE 301 Division 1, Fall 2006 Instructor: Mimi Boutin Final Examination
ECE 30 Division, all 2006 Instructor: Mimi Boutin inal Examination Instructions:. Wait for the BEGIN signal before opening this booklet. In the meantime, read the instructions below and fill out the requested
More informationChapter 5. Fourier Analysis for Discrete-Time Signals and Systems Chapter
Chapter 5. Fourier Analysis for Discrete-Time Signals and Systems Chapter Objec@ves 1. Learn techniques for represen3ng discrete-)me periodic signals using orthogonal sets of periodic basis func3ons. 2.
More informationELEN 4810 Midterm Exam
ELEN 4810 Midterm Exam Wednesday, October 26, 2016, 10:10-11:25 AM. One sheet of handwritten notes is allowed. No electronics of any kind are allowed. Please record your answers in the exam booklet. Raise
More informationSIGNALS AND SYSTEMS: PAPER 3C1 HANDOUT 6a. Dr David Corrigan 1. Electronic and Electrical Engineering Dept.
SIGNALS AND SYSTEMS: PAPER 3C HANDOUT 6a. Dr David Corrigan. Electronic and Electrical Engineering Dept. corrigad@tcd.ie www.mee.tcd.ie/ corrigad FOURIER SERIES Have seen how the behaviour of systems can
More informationLecture 27 Frequency Response 2
Lecture 27 Frequency Response 2 Fundamentals of Digital Signal Processing Spring, 2012 Wei-Ta Chu 2012/6/12 1 Application of Ideal Filters Suppose we can generate a square wave with a fundamental period
More information1.1 SPECIAL FUNCTIONS USED IN SIGNAL PROCESSING. δ(t) = for t = 0, = 0 for t 0. δ(t)dt = 1. (1.1)
SIGNAL THEORY AND ANALYSIS A signal, in general, refers to an electrical waveform whose amplitude varies with time. Signals can be fully described in either the time or frequency domain. This chapter discusses
More informationFROM ANALOGUE TO DIGITAL
SIGNALS AND SYSTEMS: PAPER 3C1 HANDOUT 7. Dr David Corrigan 1. Electronic and Electrical Engineering Dept. corrigad@tcd.ie www.mee.tcd.ie/ corrigad FROM ANALOGUE TO DIGITAL To digitize signals it is necessary
More informationSignals, Systems, and Society. By: Carlos E. Davila
Signals, Systems, and Society By: Carlos E. Davila Signals, Systems, and Society By: Carlos E. Davila Online: < http://cnx.org/content/col965/.5/ > C O N N E X I O N S Rice University, Houston, Texas
More informationThe Johns Hopkins University Department of Electrical and Computer Engineering Introduction to Linear Systems Fall 2002.
The Johns Hopkins University Department of Electrical and Computer Engineering 505.460 Introduction to Linear Systems Fall 2002 Final exam Name: You are allowed to use: 1. Table 3.1 (page 206) & Table
More informationENSC327 Communications Systems 2: Fourier Representations. School of Engineering Science Simon Fraser University
ENSC37 Communications Systems : Fourier Representations School o Engineering Science Simon Fraser University Outline Chap..5: Signal Classiications Fourier Transorm Dirac Delta Function Unit Impulse Fourier
More informationFourier Series and Fourier Transforms
Fourier Series and Fourier Transforms EECS2 (6.082), MIT Fall 2006 Lectures 2 and 3 Fourier Series From your differential equations course, 18.03, you know Fourier s expression representing a T -periodic
More information7. Find the Fourier transform of f (t)=2 cos(2π t)[u (t) u(t 1)]. 8. (a) Show that a periodic signal with exponential Fourier series f (t)= δ (ω nω 0
Fourier Transform Problems 1. Find the Fourier transform of the following signals: a) f 1 (t )=e 3 t sin(10 t)u (t) b) f 1 (t )=e 4 t cos(10 t)u (t) 2. Find the Fourier transform of the following signals:
More informationso mathematically we can say that x d [n] is a discrete-time signal. The output of the DT system is also discrete, denoted by y d [n].
ELEC 36 LECURE NOES WEEK 9: Chapters 7&9 Chapter 7 (cont d) Discrete-ime Processing of Continuous-ime Signals It is often advantageous to convert a continuous-time signal into a discrete-time signal so
More informationContinuous-time Signals. (AKA analog signals)
Continuous-time Signals (AKA analog signals) I. Analog* Signals review Goals: - Common test signals used in system analysis - Signal operations and properties: scaling, shifting, periodicity, energy and
More informationCommunication Theory Summary of Important Definitions and Results
Signal and system theory Convolution of signals x(t) h(t) = y(t): Fourier Transform: Communication Theory Summary of Important Definitions and Results X(ω) = X(ω) = y(t) = X(ω) = j x(t) e jωt dt, 0 Properties
More informationFigure 3.1 Effect on frequency spectrum of increasing period T 0. Consider the amplitude spectrum of a periodic waveform as shown in Figure 3.2.
3. Fourier ransorm From Fourier Series to Fourier ransorm [, 2] In communication systems, we oten deal with non-periodic signals. An extension o the time-requency relationship to a non-periodic signal
More information3.2 Complex Sinusoids and Frequency Response of LTI Systems
3. Introduction. A signal can be represented as a weighted superposition of complex sinusoids. x(t) or x[n]. LTI system: LTI System Output = A weighted superposition of the system response to each complex
More informationDiscrete Fourier Transform
Discrete Fourier Transform Valentina Hubeika, Jan Černocký DCGM FIT BUT Brno, {ihubeika,cernocky}@fit.vutbr.cz Diskrete Fourier transform (DFT) We have just one problem with DFS that needs to be solved.
More information