THREE HOLE SPLICE CLEVIS FOR B52 Standard finishes: ZN, GRN Wt./C 126 Lbs. (57.1 kg)
|
|
- Jemima Boyd
- 6 years ago
- Views:
Transcription
1 CLEVIS FITTINGS B169 TWO HOLE SPLICE Wt./C 84 Lbs. (38.1 kg) B168 THREE HOLE SPLICE Wt./C 126 Lbs. (57.1 kg) B167 Wt./C 178 Lbs. (80.7 kg) 3 1 /2 (88.9) B170 TWO HOLE SPLICE Wt./C 123 Lbs. (55.8 kg) 5 3 /8 (136.5) B171 THREE HOLE SPLICE Wt./C 195 Lbs. (88.4 kg) 7 B172 Wt./C 266 Lbs. (120.6 kg) 3 1 /2 (88.9) 5 3 /8 (136.5) 7 & B CLEVIS FOR B12 Wt./C 326 Lbs. (147.8 kg) 7 B172-22A CLEVIS FOR B11 OR B22A Wt./C 406 Lbs. (184.1 kg) 7 B450 U-WASHER Material: ASTM A607 Gr. 50 H HOLE SIZE 11 Gauge (3.1) 1 5 /8 (41.3) 15 /32 (11.9) Part No. Hole Size Wt./C & Size H Lbs. kg B450-1 /4 5/16 (7.9) 14 B450-3 /8 7/16 (11.1) 14 B450-1 /2 9/16 (14.3) 13 (5.8) B450-5 /8 11/16 (17.4) 13 (5.8) B450-3 /4 13/16 (20.6) 13 (5.8) 72 page 58 for general fitting and standard finish specifications.
2 FITTINGS This section offers a full selection of fittings and accessories to complete B-Line s metal framing system. are made from hot rolled, pickled and oiled plate or strip steel in accordance with ASTM A907, unless noted. Dimensions The following dimensions apply to all fittings except as noted: Hole Size 9 /16 (14.3 mm) diameter Hole Spacing 1 7 /8 (47.6 mm) on center Hole Spacing 13 /16 (20.6 mm) from end Thickness (6.3 mm) Finishes* Finish Code Finish Specification PLN Plain ASTM A907 Gr. 33 ZN Electro-Plated Zinc ASTM B633 SC3 Type III GRN Dura-Green TT-C-490B HDG Hot-Dipped Galvanized ASTM A123 SS4 Stainless Steel Type 304 ASTM A240 SS6 Stainless Steel Type 316 ASTM A240 AL Aluminum ASTM B209 *Unless otherwise noted. Load Data The load data published includes safety factor of 2.5 when used with 12 ga. (2.6) channel (safety factor = ratio of ultimate load to the design load). Use 1 /2 by 7 /8 hex head cap screws and 1 /2 (N225 or TN225) channel nuts for the rated results. Recommended Bolt Torque Bolt Size 1 / / / /2-13 Foot/Lbs Nm See chart on page 98 for setscrew torque. Width 1 5 /8 (41.3 mm) Hardware Nuts and bolts are not included with the fittings and must be ordered separately, unless noted. Metric Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters. & 58
3 MINI CHANNEL & FITTINGS B-Line s mini channels and fittings provide for an economical method of supporting light load requirements on a metal framing system. Channel Channels are cold formed on our modern rolling mills from 18 Ga. (1.2 mm) low carbon steel strips plain steel (ASTM A 611 Grade C) and pre-galvanized steel strips, (ASTM A653 SS Grade 33). A continuous slot with inturned lips provides the ability to make attachments at any point. Channel combinations are made with new state of the art, high-tech welding equipment. Lengths Standard lengths are 10 (3.05 m) and 20 (6.09 m) for B62 series, and 10 (3.05 m) for B72 series. Custom lengths are available. Mini fittings are formed from hot rolled pickled and oiled strip or sheet steel (ASTM A 607 Grade 50). The following dimensions apply to all fittings except as noted on the drawings: Hole Size 9 /32 (7.14 mm) Dia. Hole Spacing 13 /32 (10.3 mm) from end and 1 1 /16 (27.0 mm) on center. Width 13 /16 (20.6 mm) Thickness 1 /8 (3.2 mm) Finishes* Finish Code Finish Specification PLN Plain ASTM A607 Gr. 50 ZN Electro-Plated Zinc ASTM B633 SC3 Type II GRN Dura-Green TT-C-490B GALV Pre-Galvanized ASTM A653 SS Gr. 33 HDG Hot-Dipped Galvanized ASTM A123 *Unless otherwise noted. Metric Metric dimensions are shown in parentheses. Unless noted, all metric dimensions are in millimeters. Channel, & 174
4 & REFERENCE DATA METRIC CONVERSION CHART To Convert From To Multiply By To Convert From To Multiply By Angle Length degree radian (rad) x 10-2 foot (ft) meter (m) x 10-1 radian (rad) degree x inch (in) meter (m) x 10-2 mil meter (m) x 10-5 Area inch (in) micrometer (mm) x foot 2 square meter (m 2 ) x 10-2 meter (m) foot (ft) inch 2 square meter (m 2 ) x 10-4 meter (m) inch (in) x circular mil square meter (m 2 ) x meter (m) mil x sq. centimeter (cm 2 ) square inch (in 2 ) x 10-1 micrometer (mm) inch (in) x 10-5 square meter (m 2 ) foot x square meter (m 2 ) inch x Volume square meter (m 2 ) circular mil x foot 3 cubic meter (m 3 ) x 10-2 inch 3 cubic meter (m 3 ) x 10-5 Temperature cubic centimeter (cm 2 ) cubic inch (in 3 ) x 10-2 degree Fahrenheit degree Celsius t C =(t F -32)/1.8 cubic meter (m 3 ) foot x degree Celsius degree Fahrenheit t F =1.8t C +32 cubic meter (m 3 ) inch x gallon (U.S. liquid) cubic meter (m 3 ) x 10-3 Force pounds-force (lbf) newtons (N) x 10 Section Properties section modulus S (in 3 ) S (m 3 ) x 10-5 moment of inertia I (in 4 ) I (m 4 ) x 10-7 modulus of elasticity E (psi) E (Pa) x section modulus S (m 3 ) S (in 3 ) x moment of inertia I (m 4 ) I (in 4 ) x modulus of elasticity E (Pa) E (psi) x 10-4 To Convert From To Multiply By Bending Moment or Torque lbf ft newton meter (N m) lbf in newton meter (N m) x 10-1 N m lbf ft x 10-1 N m lbf in Mass ounce (avoirdupois) kilogram (kg) x 10-2 pound (avoirdupois) kilogram (kg) x 10-1 ton (short, 2000 lb) kilogram (kg) x ton (long, 2240 lb) kilogram (kg) x kilogram (kg) ounce (avoirdupois) x kilogram (kg) pound (avoirdupois) kilogram (kg) ton (short, 2000 lb) x 10-3 kilogram (kg) ton (long, 2240 lb) x 10-4 Mass Per Unit Length lb/ft kilogram per meter (kg/m) lb/in kilogram per meter (kg/m) x kg/m lb/ft x 10-1 kg/m lb/in x 10-1 Mass Per Unit Volume lb/ft 3 kilogram per cubic meter (kg/m 3 ) x lb/in 3 kilogram per cubic meter (kg/m 3 ) x kg/m 3 lb/ft x 10-2 kg/m 3 lb/in x 10-5 lbs/ft 3 lbs/in x 10-4 Mass Per Unit Area lb/ft 2 kilogram per square meter (kg/m 2 ) kg/m 2 pound per square foot (lb/ft 2 ) x 10-1 Pressure or Stress lbf/in 2 (psi) pascal (Pa) x kip/in 2 (ksi) pascal (Pa) x lbf/in 2 (psi) megapascals (MPa) x 10-3 pascal (Pa) pound-force per square inch (psi) x 10-4 pascal (Pa) kip per square inch (ksi) x 10-7 megapascals (MPa) lbf/in 2 (psi) x Defl. S.F. Ft. Pre-galv. K Factor o.c. PVC In. psi wt./c Abbreviations = Deflection = Safety Factor = Feet = Pre-galvanized Steel = Deflection Divided by load in Lbs./Ft. = On Center = Poly Vinyl Chloride = Inch = Pounds per Square Inch = Weight pre 100 pieces Metric Symbols m = meter cm = centimeter mm = millimeter µm = micrometer kg = kilogram N = newton kn = kilonewton Pa = pascal MPa = megapascal 202
5 INTRODUCTION B-Line Systems, Inc. is a leading manufacturer and fabricator of steel and aluminum products which are used in support of equipment for industrial, commercial, utility, and OEM installations. B-Line is proud of the exacting standards of research, design, engineering, and manufacturing that go into each and every product that comprise our metal framing product line. Our customers have access to the most complete support systems offered in the industry, including metal framing, cable tray, pipe hangers, slotted angle, and fasteners. Many of B-Line s products are listed by the Underwriter s Laboratories, Inc., and approved by the Factory Mutual Laboratories. All B-Line products are manufactured to meet or exceed MFMA and other industry standards set for their design and manufacture. B-Line products are produced in eight modern plants consisting of over 1,000,000 square feet. These facilities are located in Highland, Illinois; Troy, Illinois; Norcross, Georgia; Reno, Nevada; Sherman, Texas; Modesto, California; Portland, Oregon; and Aurora, Colorado. Regional sales and distribution centers are located throughout the United States stocking standard B-Line products for quick service and delivery. This catalog is designed to be helpful to engineers and contractors in the application and selection of strut products for construction and maintenance. If a unique application requires a special product not included in this catalog. B-Line engineering personnel are ready to furnish design consultation and realistic cost estimates. In addition, sales representatives with engineering know-how are located throughout the United States and abroad for your convenience. Cooper B-Line 509 West Monroe Street P.O. Box 326 Highland, Illinois Phone: B-Line Systems, Inc.
READ ONLY. Adopting Agency BSC SFM. Adopt Entire Chapter X X X X X X X X X Adopt Entire Chapter as amended (amended sections listed below)
CALIFORNIA MECHANICAL CODE MATRIX ADOPTION TABLE APPENDIX D UNIT CONVERSION TABLES (Matrix Adoption Tables are non-regulatory, intended only as an aid to the user. See Chapter 1 for state agency authority
More informationBOLT SIZE Rec.Torque Ft/Lbs. Max Torque Ft/Lbs
BOLT SIZE Rec.Torque Ft/Lbs Max Torque Ft/Lbs "-0 5 "- "- "- 5 "- "-0 () 7 (9) (5) 5 (0) 9 () 5 () 50 () 70 (95) 00 () 5 (70) 5 (70) 5 () Material Add Suffix to P/N P09 THRU P PIPE CLAMPS FOR RIGID STEEL
More informationAPPENDIX B ABBREVIATIONS, SYMBOLS AND CONVERSION FACTORS Abbreviations
APPENDIX B ABBREVIATIONS, SYMBOLS AND CONVERSION FACTORS Abbreviations A ampere AASHTO American Association of State Highway & Transportation Officials ABS (%) Percent of Absorbed Moisture Abs. Vol. Absolute
More informationSECTION 23 - METRIC DESIGN INFORMATION. Table of Contents
SECTION 23 - METRIC DESIGN INFORMATION Table of Contents Metric System Conversions and Abbreviations... 23-3 EXTREN Availability List... 23-4 EXTREN vs. Traditional Materials... 23-6 SECTION 23 METRIC
More informationAPPENDIX H CONVERSION FACTORS
APPENDIX H CONVERSION FACTORS A ampere American Association of State AASHTO Highway & Transportation Officials ABS (%) Percent of Absorbed Moisture Abs. Vol. Absolute Volume ACI American Concrete Institute
More information5. What is the moment of inertia about the x - x axis of the rectangular beam shown?
1 of 5 Continuing Education Course #274 What Every Engineer Should Know About Structures Part D - Bending Strength Of Materials NOTE: The following question was revised on 15 August 2018 1. The moment
More informationAPPENDIX D UNIT CONVERSION TABLES. Sl SYMBOLS AND PREFIXES
UNIT CONVERSION TABLES Sl SYMBOLS AND PREFIXES BASE UNITS Quantity Unit Symbol Length Meter m Mass Kilogram kg Time Second s Electric current Ampere A Thermodynamic temperature Kelvin K Amount of substance
More informationMOTOR WIRING DATA From National Electrical Code 3 PHASE SQUIRREL CAGE INDUCTION MOTORS 230 Volt 460 Volt Min. # Max. Rating
MOTOR WIRING DATA From National Electrical Code PHASE SQUIRREL CAGE INDUCTION MOTORS 20 Volt 0 Volt Min. # Max. Rating Min. Size Size of Full Size Wire Conduit Branch Circuit Load Wire AWG (inches) Fuses
More information[5] Stress and Strain
[5] Stress and Strain Page 1 of 34 [5] Stress and Strain [5.1] Internal Stress of Solids [5.2] Design of Simple Connections (will not be covered in class) [5.3] Deformation and Strain [5.4] Hooke s Law
More informationDIVISION: METALS SECTION: METAL FASTENINGS SECTION: STEEL DECKING REPORT HOLDER: PNEUTEK, INC.
ICC ES Report ICC ES () 7 () www.icc es.org Most Widely Accepted and Trusted ESR 1 Reissued /1 This report is subject to renewal /. DIVISION: METALS SECTION: METAL FASTENINGS SECTION: 1 STEEL ING REPORT
More informationINTERNATIONAL SYSTEM OF UNITS
GAP.18.2 A Publication of Global Asset Protection Services LLC INTERNATIONAL SYSTEM OF UNITS INTRODUCTION The U.S. is one of the last countries still officially using the English measurement system. Most
More informationHilti North America Installation Technical Manual Technical Data MI System Version
MIC-SA-MAH 174671 Hilti North America Installation Technical Manual Technical Data MI System Version 1. 08.017 Terms of common cooperation / Legal disclaimer The product technical data published in these
More informationHilti North America Installation Technical Manual Technical Data MI System Version
MIC-S10-AH-L 179517-1 Hilti North America Installation Technical Manual Technical Data MI System Version 1. 08.017 Terms of common cooperation / Legal disclaimer The product technical data published in
More informationMIL-HDBK-5H 1 December 1998
components are calculated. In some cases, the methods presented are empirical and subject to further refinements. Any further expansion of information on element behavior in MIL-HDBK-5 will emphasize those
More informationEXTERIOR FRAMING EXTERIOR FRAMING
1 EXTERIOR FRAMING BUILDSTRONG www.buildstrong.com 2 TABLE OF CONTENTS Product Identification...........................5 General Product Information....................... 4-5 Compliance Guaranteed...............................
More informationNAME: Given Formulae: Law of Cosines: Law of Sines:
NME: Given Formulae: Law of Cosines: EXM 3 PST PROBLEMS (LESSONS 21 TO 28) 100 points Thursday, November 16, 2017, 7pm to 9:30, Room 200 You are allowed to use a calculator and drawing equipment, only.
More information5 G R A TINGS ENGINEERING DESIGN MANUAL. MBG Metal Bar Grating METAL BAR GRATING MANUAL MBG METAL BAR GRATING NAAMM
METAL BAR NAAMM GRATNG MANUAL MBG 534-12 5 G R A TNG NAAMM MBG 534-12 November 4, 2012 METAL BAR GRATNG ENGNEERNG DEGN MANUAL NAAMM MBG 534-12 November 4, 2012 5 G R A TNG MBG Metal Bar Grating A Division
More informationTransmitters for basic requirements SITRANS P MPS (submersible sensor) Transmitter for hydrostatic level
Overview Function s are for measuring the liquid levels in wells, tanks, channels and dams. Sensor Diaphragm p U const. U +2 (brown) I EM I - (blue) 0, U B s are submersible sensors for hydrostatic level
More information8 Deflectionmax. = 5WL 3 384EI
8 max. = 5WL 3 384EI 1 salesinfo@mechanicalsupport.co.nz PO Box 204336 Highbrook Auckland www.mechanicalsupport.co.nz 2 Engineering Data - s and Columns Structural Data 1. Properties properties have been
More informationDIVISION: METALS SECTION: STEEL DECKING SECTION: STEEL ROOF DECKING REPORT HOLDER: NEW MILLENNIUM BUILDING SYSTEMS, LLC
0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2657 Reissued 05/2017 This report is subject to renewal 03/2018. DIVISION: 05 00 00 METALS SECTION:
More informationApplied Fluid Mechanics
Applied Fluid Mechanics 1. The Nature of Fluid and the Study of Fluid Mechanics 2. Viscosity of Fluid 3. Pressure Measurement 4. Forces Due to Static Fluid 5. Buoyancy and Stability 6. Flow of Fluid and
More informationALUMINUM STRUCTURAL PLATE HEADWALLS AASHTO LRFD BASIS OF DESIGN
ALUMINUM STRUCTURAL PLATE EADWALLS AASTO LRFD BASIS OF DESIGN LANE ENTERPRISES, INC. www.lane-enterprises.com Required Backfill and Load Cases: ALUMINUM STRUCTURAL PLATE EADWALLS BASIS OF DESIGN Backfill
More informationMECHANICS OF MATERIALS. Prepared by Engr. John Paul Timola
MECHANICS OF MATERIALS Prepared by Engr. John Paul Timola Mechanics of materials branch of mechanics that studies the internal effects of stress and strain in a solid body. stress is associated with the
More informationS E C T I O N 1 2 P R O D U C T S E L E C T I O N G U I D E - H E L I C A L S C R E W P I L E F O U N D A T I O N S
1. P R O D U C T S E L E C T I O N G U I D E - H E L I C A L S C R E W P I L E F O U N D A T I O N S Helical foundation pile includes a lead and extension(s). The lead section is made of a central steel
More informationConversion Factors COMMONLY USED CONVERSION FACTORS. Multiply By To Obtain
Conversion Factors COMMONLY USED CONVERSION FACTORS Multiply By To Obtain Acres................. 43,560 Square feet Acres................. 1.56 x 10-3 Square miles Acre-Feet............. 43,560 Cubic feet
More informationPressure Measurement. Transmitters for basic requirements SITRANS P MPS (submersible sensor) Transmitter for hydrostatic level 2/27
Overview Siemens AG 011 Function s are for measuring the liquid levels in wells, tanks, channels and dams. Diaphragm p Sensor U const. U + (brown) I EM I -1 (blue) 0, U B s are submersible sensors for
More informationPARTS MANUAL 2 INCH CHIPPER/SHREDDER. SC cc SUBARU
www.bearcatproducts.com 2 INCH CHIPPER/SHREDDER SC2170 170cc SUBARU PARTS MANUAL PN: 1641-00 Rev. 0011 Companion to 1509-00 Range: D01688 - Current Before You Begin DEAR ECHO BEAR CAT CUSTOMER Thank you
More informationSTYLE GUIDELINES AND SPECIFICATIONS
STYLE GUIDELINES AND SPECIFICATIONS GENERAL FILE REQUIREMENTS Important: ASME requires print-ready ( press-quality ) PDF files, with fonts embedded/saved. The authors will also be required to provide the
More informationSTEEL FRAMING AND ACCESSORIES CATALOG
STEEL FRAMING AND ACCESSORIES CATALOG ICC ES ESR-3016 2009 & 20 IBC, IRC www.cemcosteel.com Certified Steel Stud Association TABLE OF CONTENTS Section Pages Introduction to CEMCO... 3 Product Identification...4-5
More informationPlease review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam.
Group Number: Please review the following statement: I certify that I have not given unauthorized aid nor have I received aid in the completion of this exam. Signature: INSTRUCTIONS Begin each problem
More informationTension zone applications, i.e., cable trays and strut, pipe supports, fire sprinklers Seismic and wind loading
General Information Mechanical Anchors General Information Power-Stud + SD1 Wedge Expansion Anchor Product Description The Power-Stud+ SD1 anchor is a fully threaded, torque-controlled, wedge expansion
More informationSolution: The strain in the bar is: ANS: E =6.37 GPa Poison s ration for the material is:
Problem 10.4 A prismatic bar with length L 6m and a circular cross section with diameter D 0.0 m is subjected to 0-kN compressive forces at its ends. The length and diameter of the deformed bar are measured
More informationNon Newtonian Fluid Dynamics
PDHonline Course M417 (3 PDH) Non Newtonian Fluid Dynamics Instructor: Paul G. Conley, PE 2012 PDH Online PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658 Phone & Fax: 703-988-0088 www.pdhonline.org
More informationPressure Measurement Single-range transmitters for general applications
Siemens AG 07 Overview Function SITRANS LH00 Transmitter for hydrostatic level U const. p U I EM Sensor Connection for auxiliary power supply Vent pipe with humidity filter Protective conductor connection/
More information= 50 ksi. The maximum beam deflection Δ max is not = R B. = 30 kips. Notes for Strength of Materials, ET 200
Notes for Strength of Materials, ET 00 Steel Six Easy Steps Steel beam design is about selecting the lightest steel beam that will support the load without exceeding the bending strength or shear strength
More informationVIRTUAL PERFORMANCE SOLUTION EXPLICIT SOLVER REFERENCE MANUAL 2009 ESI Group (released: Mar-09)
VIRTUAL PERFORMANCE SOLUTION 2009 11 EXPLICIT SOLVER REFERENCE MANUAL UNITS Consistent The programs of the PAM-CSM family are dynamic programs and require the model (geometry, loading, material data, velocities,
More informationSTEEL. General Information
General Information General Information TYPICAL STRESS-STRAIN CURVE Below is a typical stress-strain curve. Each material has its own unique stress-strain curve. Tensile Properties Tensile properties indicate
More informationTEMPERATURE SENSOR. Model TH-T. Roctest Limited, All rights reserved.
INSTRUCTION MANUAL TEMPERATURE SENSOR Model TH-T Roctest Limited, 2005. All rights reserved. This product should be installed and operated only by qualified personnel. Its misuse is potentially dangerous.
More informationThe Metric System and Measurement
The Metric System and Measurement Introduction The metric system is the world standard for measurement. Not only is it used by scientists throughout the world, but most nations have adopted it as their
More informationG-FIRE FLANGE ADAPTERS
G-FIRE FLANGE ADAPTERS 21 G-FIRE FLANGE ADAPTERS Pictorial Table of Contents MATERIAL SPECIFICATIONS Issue 03, 04, 07 Cert No. 570, 669, 673 For detailed Listing and Approval information see pages 101-10
More informationDetermine the resultant internal loadings acting on the cross section at C of the beam shown in Fig. 1 4a.
E X M P L E 1.1 Determine the resultant internal loadings acting on the cross section at of the beam shown in Fig. 1 a. 70 N/m m 6 m Fig. 1 Support Reactions. This problem can be solved in the most direct
More informationProduct description. Compact Modules. Characteristic features. Further highlights
4 Compact Modules Product description Characteristic features Five fine-tuned sizes based on a compact precision aluminum profile with two integrated pre-tensioned ball rail systems Identical external
More informationSolid Mechanics Homework Answers
Name: Date: Solid Mechanics Homework nswers Please show all of your work, including which equations you are using, and circle your final answer. Be sure to include the units in your answers. 1. The yield
More informationCONNECTION DESIGN. Connections must be designed at the strength limit state
CONNECTION DESIGN Connections must be designed at the strength limit state Average of the factored force effect at the connection and the force effect in the member at the same point At least 75% of the
More informationBack to Basics: Realizing Cabling Determines Design. F. Patrick Mahoney, CSI CDT, RCDD Direct Supply - Aptura
Back to Basics: Realizing Cabling Determines Design F. Patrick Mahoney, CSI CDT, RCDD Direct Supply - Aptura Back to Basics: Realizing Cabling Determines Design Cabling distribution design implementation
More informationScientific Units of Measurement & Conversion
Scientific Units of Measurement & Conversion Principle or Rationale: Scientific measurements are made and reported using the metric system and conversion between different units is an integral part of
More informationHigh Tech High Top Hat Technicians. An Introduction to Solid Mechanics. Is that supposed to bend there?
High Tech High Top Hat Technicians An Introduction to Solid Mechanics Or Is that supposed to bend there? Why don't we fall through the floor? The power of any Spring is in the same proportion with the
More informationP U M P S. The quality standard for hydraulic efficiency and suction lift. PERIPHERAL PUMPS TEP/ TSP - SERIES 50Hz
P U M P S THE BENCHMARK FOR PERFORMANCE The quality standard for hydraulic efficiency and suction lift. PERIPHERAL PUMPS TEP/ TSP - SERIES 5Hz I N D E X TEP / TSP SERIES - PERIPHERAL PUMPS Page No. General
More informationChemistry Section Review 2.2
Chemistry Section Review 2.2 Multiple Choice Identify the choice that best completes the statement or answers the question. 1. Standards of measurement are chosen because they a. can be related to everyday
More informationSteel Post Load Analysis
Steel Post Load Analysis Scope The steel posts in 73019022, 73019024, and 73019025, are considered to be traditional building products. According to the 2015 International Building Code, this type of product
More informationTECHNICAL CORRECTION July Process Industry Practices Structural. PIP STE03360 Heat Exchanger and Horizontal Vessel Foundation Design Guide
TECHNICAL CORRECTION July 2007 Structural Heat Exchanger and Horizontal Vessel Foundation Design Guide PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry
More informationSteel Cross Sections. Structural Steel Design
Steel Cross Sections Structural Steel Design PROPERTIES OF SECTIONS Perhaps the most important properties of a beam are the depth and shape of its cross section. There are many to choose from, and there
More informationAPI 11E - Specification for Pumping Units
API 11E - Specification for Pumping Units 5 Beam Pump Structure Requirements 5.1 General Requirements for beam pump structures are specified in the following sections. Only loads imposed on the structure
More informationMETAR CABLE MANAGEMENT SYSTEMS UNISTRUT METAL FRAMING SYSTEMS TECHNICAL DATA. bonn metals CONSTRUCTION INDUSTRIES L.L.C.
METAR CABLE MANAGEMENT SYSTEMS UNISTRUT METAL FRAMING SYSTEMS TECHNICAL DATA bonn metals CONSTRUCTION INDUSTRIES L.L.C. CONTENTS PREFACE 01 MATERIAL AND FINISHES 02 DESIGN CONSIDERATIONS 05 INTRODUCTION
More informationSOLUTION (17.3) Known: A simply supported steel shaft is connected to an electric motor with a flexible coupling.
SOLUTION (17.3) Known: A simply supported steel shaft is connected to an electric motor with a flexible coupling. Find: Determine the value of the critical speed of rotation for the shaft. Schematic and
More informationProPress (304 FKM) 1.3
ProPress (304 FKM) 41 ProPress (304 FKM) Viega ProPress for stainless is engineered for harsh industrial environments where the piping systems may come into contact with corrosive cleaning liquids. A complete
More informationNorthern Lesson 2 Gear Pump Terminology. Gear Pump 101. Lesson 2: Gear Pump Terminology. When your reputation depends on it!
Gear Pump 101 Lesson 2: Gear Pump Terminology When your reputation depends on it! Symbol Term Metric Unit Abbreviation US Customary Unit Abbreviation Conversion factor a A Area square millimeter mm2 square
More information1.105 Solid Mechanics Laboratory Fall 2003 Experiment 3 The Tension Test
1.105 Solid Mechanics Laboratory Fall 2003 Experiment 3 The Tension Test Our objective is to measure the Elastic Modulus of steel. The experiment comes in two parts. In the first, you will subject a steel
More informationEdward C. Robison, PE, SE. 02 January Architectural Metal Works ATTN: Sean Wentworth th ST Emeryville, CA 94608
Edward C. Robison, PE, SE ks ATTN: Sean Wentworth 1483 67 th ST Emeryville, CA 94608 02 January 2013 SUBJ: 501 CORTE MADERA AVE, CORTE MADERA, CA 94925 BALCONY GUARD BASE PLATE MOUNTS The guards for the
More informationTelescope Mechanical Design
Telescope Mechanical Design Albert Lin The Aerospace Corporation (310) 336-1023 albert.y.lin@aero.org 6/27/06 6/27/06 Telescope Mechanical Design 1 Overview Design Overview Instrument Requirements Mechanical
More informationU.S. Patents 6,290,217 6,244,579
CR CR Series Overview U.S. Patents 6,90,7 6,,579 For the best in vibration isolation capabilities, choose Enidine s. Smaller than traditional wire ropes, these unique isolators provide cost-effective,
More informationproduct manual H-3030, H-3032, H-3033 Concrete Beam Tester
05.09 product manual H-3030, H-3032, H-3033 Concrete Beam Tester Introduction These self-contained portable concrete beam testers accurately and easily determine flexural strengths of 6 x 6" cross-section
More informationChapter 1 Introduction- Concept of Stress
hapter 1 Introduction- oncept of Stress INTRODUTION Review of Statics xial Stress earing Stress Torsional Stress 14 6 ending Stress W W L Introduction 1-1 Shear Stress W W Stress and Strain L y y τ xy
More informationNICE-PACK ALCOHOL PREP ROOM PLATFORM CALCULATIONS
DESIGN STATEMENT THIS GALVANISED STEEL PLATFORM IS ANALYSED USING THE ALLOWABLE STRESS DESIGN METHOD TO DETERMINE MATERIAL STRENGTH. MEMBER SIZES AND FASTENERS ARE CHOSEN NOT SO MUCH FOR THEIR STRENGTH
More informationThe Metric System and Measurement
Introduction The Metric System and Measurement The metric system is the world standard for measurement. Not only is it used by scientists throughout the world, but most nations have adopted it as their
More informationThe LAT Electronics consists of five distinct box assemblies as follows:
I. SYNOPSIS The preliminary stress analyses for the DAQ Electronics assemblies have been performed per the conditions specified in the Environmental Specification LAT-SS-00778. The analysis considered
More informationSolving Problems with Labeled Numbers
Solving Problems with Labeled Numbers When solving problems with labeled numbers (those with units such as grams or liters), the labels are treated in the same way as P or y in algebra. The problem is
More informationDonald P. Shiley School of Engineering ME 328 Machine Design, Spring 2019 Assignment 1 Review Questions
Donald P. Shiley School of Engineering ME 328 Machine Design, Spring 2019 Assignment 1 Review Questions Name: This is assignment is in workbook format, meaning you may fill in the blanks (you do not need
More informationmy!wind Ltd 5 kw wind turbine Static Stability Specification
my!wind Ltd 5 kw wind turbine Static Stability Specification 1 P a g e 0 3 / 0 4 / 2 0 1 4 Contents Contents... 2 List of Changes... 2 Appendixes... 2 General remarks... 3 1. Introduction... 4 2. Geometry...
More informationBELT TENSIONS & HP RESULTS
13 12 120' 3 SECTIONS @ 100' ARC 300' 7 SECTIONS @ 100' LOADING #1 1200 TPH 120' 204' ~ 1432.4' RADIUS 1696.1' CONVEYOR INPUT DATA BELT TENSIONS & HP RESULTS BELT WIDTH, inches = CAPACITY, tph = DENSITY,
More informationWeights and Measures Metric Conversion Factors (Symbols of SI units, multiples, and submultiples are given in parentheses in the right hand column)
Cambelt International Corp www.cambelt.com Weights and Measures Metric Conversion Factors (Symbols of SI units, multiples, and submultiples are given in parentheses in the right hand column) Multiply By
More informationSteel Framing Components Catalog
Certified Manufacturer of Drywall & Structural Framing & Accessories Steel Framing Components Catalog Toll Free:.8..888 Fax: 58.. www.statebp.com 5 Schmeman Warren, MI 8089 State Building Products, Inc.
More informationNEW. HALFEN Adjustable Cantilever A REVOLUTION IN TUNNEL PIPE SUPPORT
NEW HAFEN Adjustable Cantilever A REVOUTION IN TUNNE PIPE SUPPORT HAFEN Adjustable Cantilever The advantages at a glance The HAFEN Adjustable Cantilever combines the established high load bearing of the
More informationErrata (Includes critical corrections only for the 1 st, 2 nd & 3 rd reprints)
Errata (Includes critical corrections only for the 1 st, 2 nd & 3 rd reprints) Mechanics of Materials, 8e James M. Gere & Barry J. Goodno ISBN: 9781111577735 Page Number Description of Correction 15 Example
More informationTable 10-T-11 : Alphabetical Listings of Common Conversions
ISHRAE Handbook UNITS AND CONVERSIONS 10.8 Table 10-T-11 : Alphabetical Listings of Common Conversions To convert from To Multiply by Acres Square feet 43,560 Acres Square meters 4074 Acres Square miles
More informationNAIL SECTION TABLE OF CONTENTS
NAIL SECTION TABLE OF CONTENTS ANCHOR TRUSS BOX NAILS-1 NAILS-1 COMMMON NAILS-1 & 2 DECK NAILS NAILS-2 & 3 DRYWALL DUPLEX FINISH FLOOR - HARD SCREW NAILS-4 NAILS-4 NAILS-5 NAILS-5 MASONRY - STUB NAILS-6
More informationP U M P S. The quality standard for hydraulic efficiency and suction lift. PERIPHERAL PUMPS TEP/ TSP - SERIES 50Hz
P U M P S THE BENCHMARK FOR PERFORMANCE The quality standard for hydraulic efficiency and suction lift. PERIPHERAL PUMPS TEP/ TSP - SERIES 5Hz I N D E X TEP / TSP / TRP SERIES - PERIPHERAL PUMPS Page
More informationThe following pages are an excerpt from the North American Product Technical Guide, Volume 1: Direct Fastening Technical Guide, Edition 18.
The following pages are an excerpt from the North American Product Technical Guide, Volume 1: Direct Fastening Technical Guide, Edition. Please refer to the publication in its entirety for complete details
More informationSolutions to: Units and Calculations Homework Problem Set Chemistry 145, Chapter 1
to: Units and Calculations Homework Problem Set Chemistry 145, Chapter 1 1. Give the name and abbreviation of the SI Unit for: a. Length meter m b. Mass kilogram kg c. Time second s d. Electric Current
More informationU.S. pound (lb) foot (ft) foot-pounds (ft-lb) pound (lb) inch (in) inch-pounds (in-lb) tons foot (ft) foot-tons (ft-ton)
Math 1206 Calculus Sec. 6.4: Work I. Work Done by a Constant Force A. Def n : If an object is moved a distance D in the direction of an applied constant force F, then the work W done by the force is defined
More informationTechnical Data Sheet DPT & DPIT-4005 SERIES DIFFERENTIAL PRESSURE TRANSDUCERS. Features. Description
Technical Data Sheet DPT & DPIT-4005 SERIES DIFFERENTIAL PRESSURE TRANSDUCERS Description The 4005 series of differential pressure transducers include Models DPT-4005 and DPIT-4005-M. The 4005 series differential
More informationIf the solution does not follow a logical thought process, it will be assumed in error.
Please indicate your group number (If applicable) Circle Your Instructor s Name and Section: MWF 8:30-9:20 AM Prof. Kai Ming Li MWF 2:30-3:20 PM Prof. Fabio Semperlotti MWF 9:30-10:20 AM Prof. Jim Jones
More informationUseful Formulas and Calculations
Drive Design Speed Ratio = rpm (faster) = PD = N rpm (slower) pd n Where: rpm = Revolutions per minute PD = Larger pitch diameter pd = Smaller pitch diameter N = Larger sprocket grooves n = Smaller sprocket
More informationZF Series Force Transducers
Data Sheet Series Force Transducers FEATURES 1 kn to 00 kn High accuracy For tensile or pressure forces Made of stainless steel Enclosure protection IP 67 DESCRIPTION The force transducers of the series
More informationPowerPoint Presentation by: Associated Technical Authors. Publisher The Goodheart-Willcox Company, Inc. Tinley Park, Illinois
Althouse Turnquist Bracciano PowerPoint Presentation by: Associated Technical Authors Publisher The Goodheart-Willcox Company, Inc. Tinley Park, Illinois Chapter 1 History and Fundamentals of Refrigeration
More information1040 SLIDING MALL FRONT
APRIL, 00 00 SLIDING MALL FRONT INDEX INDEX... ELEVATIONS/VERTICAL SECTION DETAILS... HORIZONTAL SECTION DETAILS... EGRESS DOOR... - STACK AREA LAYOUT... - SIZE LIMITATIONS... HARDWARE...0 LAWS AND BUILDING
More informationUnit 1 - INTRODUCTION MEDICAL MATH Listening guide
Unit 1 - INTRODUCTION MEDICAL MATH Listening guide Name Period 1. List one important reason that healthcare workers must be proficient in math. 2. Number forms: 3. Basic math: Counting numbers and zero
More informationAllowable Design Stresses (psi)
8 0 0. 2 2 1. 2 3 2 6 w w w. a n t h o n y f o r e s t. c o m 2 Allowable Design Stresses (psi) Power Beam Section Properties and Allowable Capacities 7.0 9.0 9.2 10.9 11.6 13.6 15.6 17.5 11.1 14.1 14.5
More informationThis procedure covers the determination of the moment of inertia about the neutral axis.
327 Sample Problems Problem 16.1 The moment of inertia about the neutral axis for the T-beam shown is most nearly (A) 36 in 4 (C) 236 in 4 (B) 136 in 4 (D) 736 in 4 This procedure covers the determination
More informationChapter kn m/kg Ans kn m/kg Ans. 187 kn m/kg Ans.
Chapter -1 From Tables A-0, A-1, A-, and A-4c, (a) UNS G1000 HR: S ut = 80 (55) MPa (kpsi), S yt = 10 (0) MPa (kpsi) Ans. (b) SAE 1050 CD: S ut = 690 (100) MPa (kpsi), S yt = 580 (84) MPa (kpsi) Ans. (c)
More information1 Exterior Wall Members & Accessories
JamStud Introduction Table of Contents JamStud Introduc on...1 JamStud Assembly Comparisons...2 JamStud Design Considera ons...3- JamStud Sec on Proper es...5- JamStud Non Load Bearing Design Example...7-
More informationLearning Plan 4 Chapter 9
Learning Plan 4 Chapter 9 Question The population of a country reached 309.5 million people. The total area is 3.25 million square miles. What is the population density for the country? Round to the nearest
More informationLength is the distance from one point to another. Length has standard units of measurement such as inches or centimeters.
Page 1 Measurements are a standard set by different cultures to address their own needs. In the United States, we use the U. S. Customary system of units. However, the metric system is used worldwide.
More informationAPPENDIX A Thickness of Base Metal
APPENDIX A Thickness of Base Metal For uncoated steel sheets, the thickness of the base metal is listed in Table A.1. For galvanized steel sheets, the thickness of the base metal can be obtained by subtracting
More informationCOLUMNS: BUCKLING (DIFFERENT ENDS)
COLUMNS: BUCKLING (DIFFERENT ENDS) Buckling of Long Straight Columns Example 4 Slide No. 1 A simple pin-connected truss is loaded and supported as shown in Fig. 1. All members of the truss are WT10 43
More informationExperimental Lab. Principles of Superposition
Experimental Lab Principles of Superposition Objective: The objective of this lab is to demonstrate and validate the principle of superposition using both an experimental lab and theory. For this lab you
More informationNEBB Fundamental Formulas
Approved NEBB - May 1, 17 Page 1 of 8 Version 1.3 A = Area (ft²) IP, (m²) SI M = Mass (lb) IP, (kg) SI ACH = Air Changes per Hour ma = Mixed Air Ak = Effective Area m = meter (metre) AV = Average m³/s
More informationStress Transformation Equations: u = +135 (Fig. a) s x = 80 MPa s y = 0 t xy = 45 MPa. we obtain, cos u + t xy sin 2u. s x = s x + s y.
014 Pearson Education, Inc., Upper Saddle River, NJ. All rights reserved. This material is protected under all copyright laws as they currently 9 7. Determine the normal stress and shear stress acting
More informationConfigurations & Parts Identification
Suspension Series Configurations & Parts Identification Advancing the Practical Application of Suspension Technology Springfield, MO n (800) 654-8824 n (417) 862-5012 Fax (417) 862-2317 n www.hutchensindustries.com
More informationStress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus. Case study
Stress Strain Elasticity Modulus Young s Modulus Shear Modulus Bulk Modulus Case study 2 In field of Physics, it explains how an object deforms under an applied force Real rigid bodies are elastic we can
More information