Steel connections. Connection name : MEP_BCF_W=14.29[mm]_W=6.35[mm]_tp=63.5[mm]_N=0_N=2_N=0_N=1_W=14.29[mm]_W=14.29[mm]_W=14.29[ mm] Connection ID : 1
|
|
- Cameron Perry
- 5 years ago
- Views:
Transcription
1 Current Date: 08-Dec-13 7:05 PM Units system: SI File name: E:\ram\1\1.cnx\ Microsoft Steel connections Detailed report Connection name : MEP_BCF_W=14.29[mm]_W=6.35[mm]_tp=63.5[mm]_N=0_N=2_N=0_N=1_W=14.29[mm]_W=14.29[mm]_W=14.29[ mm] Connection ID : 1 Design code : AISC LRFD Family Type : Moment end plate (MEP) : Beam - Column flange (BCF) LOADS Members Load Type V2 V3 M33 M22 Axial [KN] [KN] [KN*m] [KN*m] [KN] Right beam 1 - DL Design D1 Design GEOMETRIC CONSIDERATIONS Dimensions Unit Value Min. value Max. value Sta. References Extended end plate Vertical edge distance [mm] Sec. J3.5 L emin = e dmin + C 2 = 33.65[mm] + 0[mm] = 33.65[mm] Tables J3.4, J3.5 L emax = min(12*t p, 6[in]) = min(12*20[mm], 6[in]) = 152.4[mm] Sec. J3.5 Horizontal edge distance [mm] Sec. J3.5 L emin = e dmin + C 2 = 33.65[mm] + 0[mm] = 33.65[mm] Tables J3.4, J3.5 L emax = min(12*t p, 6[in]) = min(12*20[mm], 6[in]) = 152.4[mm] Sec. J3.5 Haunch vertical bolt spacing [mm] Sec. J3.3 s min = 8/3*d = 8/3*20[mm] = [mm] Sec. J3.3 Horizontal center-to-center spacing (gage) [mm] Sec. J3.3, DG4 Sec. 2.4, DG4 Sec. 2.1, 2.4, DG16 Sec. 2.5 g min = max(8/3*d, 2*k 1c + 2*d, t wb + 2*w + d h ) = max(8/3*20[mm], 2*10.5[mm] + 2* 20[mm], 6[mm] + 2*6.35[mm] [mm]) = 61[mm] Sec. J3.3, DG4 Sec. 2.4 g max = b fb = 101.9[mm] DG4 Sec. 2.1,
2 2.4, DG16 Sec. 2.5 Inner distance from bolt centerline to top flange [mm] DG4 Sec. 2.1 d<=1[in] 20[mm]<=1[in] True p fmin = d + 1/2[in] = 20[mm] + 1/2[in] = 32.7[mm] DG4 Sec. 2.1 Inner distance from bolt centerline to haunch flange [mm] DG4 Sec. 2.1 d<=1[in] 20[mm]<=1[in] True p fmin = d + 1/2[in] = 20[mm] + 1/2[in] = 32.7[mm] DG4 Sec. 2.1 Bolt diameter [mm] DG4 Sec. 1.1 d bmax = 1.5[in] DG4 Sec. 1.1 Moment end plate behavior at beam top flange Thick plate behavior controlled by no prying bolt rupture Moment end plate behavior at beam bottom flange Thick plate behavior controlled by no prying bolt rupture Beam Weld size (Top flange) [1/16in] table J2.4 Weld size (Bottom flange) [1/16in] table J2.4 Weld size (Web) [1/16in] table J2.4 Weld size (Haunch flange) [1/16in] table J2.4 Weld size (Haunch to beam) [1/16in] table J2.4 Support Flange thickness [mm] DG16 Sec 2.5, DG16 Eq. 2-7 s = 0.5*(b p *g) 1/2 = 0.5*(145[mm]*65[mm]) 1/2 = [mm] DG16 Table 3-2 p f = min(p f, s) = min(40[mm], [mm]) = 40[mm] DG16 Table 3-2 Y p = b p /2*(h 1 *(1/p f ) + h 2 *(1/s)) + 2/g*(h 1 *(p f *p b ) + h 2 *(s * p b )) + g/2 = 145[mm]/2*(459.37[mm]*(1/40[mm]) [mm]*(1/ [mm])) + 2/65[mm]* (459.37[mm]*(40[mm] *70[mm]) [mm]*( [mm] *70[mm])) + 65[mm]/2 = [mm] DG16 Table 3-3 IsFlushConnection True r = 1.25 DG16 Sec 2.5 M np = 2*P t *( d n ) = 2*137.2[KN]*(840.35[mm]) = [KN*m] DG16 Sec 2.5 M np = 2*P t *( d n ) = 2*137.2[KN]*(840.35[mm]) = [KN*m] DG16 Sec 2.5 s = 0.5*(b p *g) 1/2 = 0.5*(145[mm]*65[mm]) 1/2 = [mm] DG16 Table 3-2 p f = min(p f, s) = min(40[mm], [mm]) = 40[mm] DG16 Table 3-2 Y p = b p /2*(h 1 *(1/p f ) + h 2 *(1/s)) + 2/g*(h 1 *(p f *p b ) + h 2 *(s * p b )) + g/2 = 145[mm]/2*(459.37[mm]*(1/40[mm]) [mm]*(1/ [mm])) + 2/65[mm]* (459.37[mm]*(40[mm] *70[mm]) [mm]*( [mm] *70[mm])) + 65[mm]/2 = [mm] DG16 Table 3-3 M pl = F yp *t 2 p *Y p = 0.275[KN/mm2]*20[mm] 2 * [mm] = [KN*m] DG16 Sec 2.5
3 w' = b p /2 - (d + 1/16[in]) = 145[mm]/2 - (20[mm] + 1/16[in]) = [mm] DG16 Sec 2.5 a i = 3.682*(t p /d) 3 [in] [in] = 3.682*(20[mm]/20[mm]) 3 [in] [in] = [mm] DG16 Sec 2.5 F i ' = (t p 2 *F yp *(0.85*b p / *w') + PI*d 3 *F nt /8)/(4*p fi ) = (20[mm] 2 *0.275[KN/ mm2]*(0.85*145[mm]/ * [mm]) + PI*20[mm] 3 *0.56[KN/mm2]/8)/(4*40[mm]) = [K... DG16 Sec 2.5 discr = F yp 2-3*(F i '/(w'*t p )) 2 = 0.275[KN/mm2] 2-3*( [KN]/( [mm]* 20[mm])) 2 = [KN] DG16 Sec 2.5 Q maxi = (w'*t p 2 )/(4*a i )*(F yp 2-3*(F i '/(w'*t p )) 2 ) 1/2 = ( [mm]*20[mm] 2 )/ (4* [mm])*(0.275[KN/mm2] 2-3*( [KN]/( [mm]*20[mm])) 2 ) 1/2 = [KN] DG16 Sec 2.5 M q = max(2*(p t - Q maxi )*(d 1 + d 2 ), 2*T b *(d 1 + d 2 )) = max(2*(137.2[kn] [KN])*(455.17[mm] [mm]), 2*0[KN]*(455.17[mm] [mm])) = [KN*m] DG16 Sec 2.5 IsFlushConnection True r = 1.25 DG16 Sec 2.5 ThickPlateSmallerBoltsBehaviorApply = M np <( bmpl /1.11) = [KN*m]<(389.99[KN*m]/1.11) = True DG16 Sec 2.5 t preq = ((1.11* r * *M np )/( b *F yp *Y p )) 1/2 = ((1.11*1.25*0.75*230.59[KN*m])/(0.9* 0.275[KN/mm2]* [mm])) 1/2 = [mm] DG16 Eq. 2-7 Horizontal edge distance [mm] Sec. J3.5 L emin = e dmin + C 2 = 33.65[mm] + 0[mm] = 33.65[mm] Tables J3.4, J3.5 L emax = min(12*t p, 6[in]) = min(12*7[mm], 6[in]) = 84[mm] Sec. J3.5 Column flange behavior at beam top flange Thin plate behavior controlled by plate yielding Column flange behavior at beam bottom flange Thin plate behavior controlled by plate yielding WARNINGS Bolt gage and bolt horizontal edge distance produce unsuitable geometry DESIGN CHECK Verification Unit Capacity Demand Ctrl EQ Ratio References Moment end plate TOP FLANGE Flexural yielding [KN*m] D DG16 Sec 2.5 s = 0.5*(b p *g) 1/2 = 0.5*(145[mm]*65[mm]) 1/2 = [mm] DG16 Table 3-2 p f = min(p f, s) = min(40[mm], [mm]) = 40[mm] DG16 Table 3-2 Y p = b p /2*(h 1 *(1/p f + 1/s)) + 2/g*(h 1 *(p f + s)) = 145[mm]/2*(458.8[mm]*(1/40[mm] + 1/ [mm])) + 2/65[mm]*(458.8[mm]*(40[mm] [mm])) = [mm] DG16 Table 3-2 M pl = F yp *t 2 p *Y p = 0.275[KN/mm2]*20[mm] 2 * [mm] = [KN*m] DG16 Sec 2.5 IsFlushConnection True r = 1.25 DG16 Sec 2.5 M n = b *M pl / r = 0.9*304.34[KN*m]/1.25 = [KN*m] DG16 Sec 2.5 No prying bolt moment strength [KN*m] D DG16 Sec 2.5 M np = 2*P t *( d n ) = 2*137.2[KN]*(454.89[mm]) = [KN*m] DG16 Sec 2.5 M n = *M np = 0.75*124.82[KN*m] = [KN*m] DG16 Sec 2.5 Bolts shear [KN] D Eq. J3-1 R n = 2 * ( *F nv *A b ) = 2 * (0.75*0.375[KN/mm2]*245[mm2]) = [KN] Eq. J3-1 Connector bolt bearing [KN] D Eq. J3-6 L c-end = max(0.0, L e - d h /2) = max(0.0, 40[mm] [mm]/2) = [mm] Sec. J4.10
4 L c-spa = max(0.0, s - d h ) = max(0.0, 0[mm] [mm]) = 0[mm] Sec. J4.10 R n = *(min(k 1 *L c-end, k 2 *d) + min(k 1 *L c-spa, k 2 *d)*(n - 1))*t p *F u * n c = 0.75*(min(1.2* [mm], 2.4*20[mm]) + min(1.2*0[mm], 2.4*20[mm])*(1-1))*20[mm]* 0.415[KN/mm2]*2 = [KN] Eq. J3-6 Shear yielding [KN] D DG4 Eq R n = *0.6*F yp *b p *t p = 0.9*0.6*0.275[KN/mm2]*145[mm]*20[mm] = [KN] DG4 Eq BOTTOM FLANGE (Haunch) Flexural yielding [KN*m] D DG16 Sec 2.5 s = 0.5*(b p *g) 1/2 = 0.5*(145[mm]*65[mm]) 1/2 = [mm] DG16 Table 3-2 p f = min(p f, s) = min(40[mm], [mm]) = 40[mm] DG16 Table 3-2 Y p = b p /2*(h 1 *(1/p f ) + h 2 *(1/s)) + 2/g*(h 1 *(p f *p b ) + h 2 *(s * p b )) + g/2 = 145[mm]/2*(459.37[mm]*(1/40[mm]) [mm]*(1/ [mm])) + 2/65[mm]* (459.37[mm]*(40[mm] *70[mm]) [mm]*( [mm] *70[mm])) + 65[mm]/2 = [mm] DG16 Table 3-3 M pl = F yp *t 2 p *Y p = 0.275[KN/mm2]*20[mm] 2 * [mm] = [KN*m] DG16 Sec 2.5 IsFlushConnection True r = 1.25 DG16 Sec 2.5 M n = b *M pl / r = 0.9*389.99[KN*m]/1.25 = [KN*m] DG16 Sec 2.5 No prying bolt moment strength [KN*m] D DG16 Sec 2.5 M np = 2*P t *( d n ) = 2*137.2[KN]*(840.35[mm]) = [KN*m] DG16 Sec 2.5 M n = *M np = 0.75*230.59[KN*m] = [KN*m] DG16 Sec 2.5 Bolts shear [KN] D Eq. J3-1 R n = 4 * ( *F nv *A b ) = 4 * (0.75*0.375[KN/mm2]*245[mm2]) = [KN] Eq. J3-1 Connector bolt bearing [KN] D Eq. J3-6 L c-end = max(0.0, L e - d h /2) = max(0.0, 40[mm] [mm]/2) = [mm] Sec. J4.10 L c-spa = max(0.0, s - d h ) = max(0.0, 70[mm] [mm]) = [mm] Sec. J4.10 R n = *(min(k 1 *L c-end, k 2 *d) + min(k 1 *L c-spa, k 2 *d)*(n - 1))*t p *F u * n c = 0.75*(min(1.2* [mm], 2.4*20[mm]) + min(1.2* [mm], 2.4*20[mm])*(2-1))*20[mm]* 0.415[KN/mm2]*2 = [KN] Eq. J3-6 Shear yielding [KN] D DG4 Eq R n = *0.6*F yp *b p *t p = 0.9*0.6*0.275[KN/mm2]*145[mm]*20[mm] = [KN] DG4 Eq R n = *0.6*F yp *b p *t p = 0.9*0.6*0.275[KN/mm2]*145[mm]*20[mm] = [KN] DG4 Eq Beam Web weld shear strength [KN] D Eq. J2-4 F w = 0.6*F EXX = 0.6* [KN/mm2] = [KN/mm2] Sec. J2.4 A w = (2) 1/2 /2*(D/16)*[in]*L = (2) 1/2 /2*(4/16)*[in]*112.6[mm] = [mm2] Sec. J2.4 R n = 2 * ( *F w *A w ) = 2 * (0.75* [KN/mm2]*505.59[mm2]) = [KN] Eq. J2-4 Web weld strength to reach yield stress [KN/m] D Eq. J4-1, Eq. J2-4 R n = *F y *t w = 0.9*0.275[KN/mm2]*6[mm] = 1485[KN/m] Eq. J4-1 LoadAngleFactor = *(sin( )) 1.5 = *(sin( )) 1.5 = 1.5 p. 8-9 F w = 0.6*F EXX *LoadAngleFactor = 0.6* [KN/mm2]*1.5 = [KN/mm2] Sec. J2.5 R w = 2 * ( *F w *(2) 1/2 /2*D/16[in]) = 2 * (0.75* [KN/mm2]*(2) 1/2 /2*4/16[in]) = [KN/m] Eq. J2-4
5 Shear yielding [KN] D Eq. J4-3 A g = L p *t p = 257.2[mm]*6[mm] = [mm2] Sec. D3-1 R n = *0.60*F y *A g = 1*0.60*0.275[KN/mm2]*1543.2[mm2] = [KN] Eq. J4-3 TOP FLANGE Flange weld capacity [KN] D Eq. J2-4 LoadAngleFactor = *(sin( )) 1.5 = *(sin( )) 1.5 = 1.5 p. 8-9 F w = 0.6*F EXX *LoadAngleFactor = 0.6* [KN/mm2]*1.5 = [KN/mm2] Sec. J2.5 A w = (2) 1/2 /2*(D/16)*[in]*L = (2) 1/2 /2*(4/16)*[in]*214.6[mm] = [mm2] Sec. J2.4 R n = *F w *A w = 0.75* [KN/mm2]*963.58[mm2] = [KN] Eq. J2-4 BOTTOM FLANGE Flange weld capacity [KN] D Eq. J2-4 LoadAngleFactor = *(sin( )) 1.5 = *(sin( )) 1.5 = 1.5 p. 8-9 F w = 0.6*F EXX *LoadAngleFactor = 0.6* [KN/mm2]*1.5 = [KN/mm2] Sec. J2.5 A w = (2) 1/2 /2*(D/16)*[in]*L = (2) 1/2 /2*(4/16)*[in]*214.6[mm] = [mm2] Sec. J2.4 R n = *F w *A w = 0.75* [KN/mm2]*963.58[mm2] = [KN] Eq. J2-4 Beam haunch Yielding strength due to axial load [KN] D Eq. J4-1 R n = *F y *A g = 0.9*0.275[KN/mm2]*711.2[mm2] = [KN] Eq. J4-1 Compression strength [KN] D Eq. J4-6 r = t p /(12) 1/2 = 7[mm]/(12) 1/2 = [mm] Sec. E2 K*L/r> *559.02[mm]/ [mm]>25 True F e = PI 2 *E/(K*L/r) 2 = PI 2 *205[KN/mm2]/(0.65*559.02[mm]/ [mm]) 2 = [KN/mm2] Eq. E3-4 F e >=0.44*Q*F y [KN/mm2]>=0.44*1*0.275[KN/mm2] False F cr = 0.877*F e = 0.877* [KN/mm2] = [KN/mm2] Sec. E7 A g = L p *t p = 101.6[mm]*7[mm] = 711.2[mm2] Sec. D3-1 P n = *F cr *A g = 0.9* [KN/mm2]*711.2[mm2] = [KN] Eq. J4-6 Flange weld capacity [KN] D Eq. J2-4 LoadAngleFactor = *(sin( )) 1.5 = *(sin( )) 1.5 = 1.5 p. 8-9 F w = 0.6*F EXX *LoadAngleFactor = 0.6* [KN/mm2]*1.5 = [KN/mm2] Sec. J2.5 A w = (2) 1/2 /2*(D/16)*[in]*L = (2) 1/2 /2*(4/16)*[in]*211.4[mm] = [mm2] Sec. J2.4 R n = *F w *A w = 0.75* [KN/mm2]*949.21[mm2] = [KN] Eq. J2-4 Web weld capacity [KN] D Sec. J2.4, Eq. J2-9 F w = 0.6*F EXX = 0.6* [KN/mm2] = [KN/mm2] Sec. J2.4 A w = (2) 1/2 /2*(D/16)*[in]*L = (2) 1/2 /2*(4/16)*[in]*500[mm] = [mm2] Sec. J2.4 R wl = 2 * ( *F w *A w ) = 2 * (0.75* [KN/mm2]* [mm2]) = [KN] Eq. J2-9 Local flange bending [KN] D Eq. J10-1 IsMemberEnd False R n = *6.25*t 2 f *F yf = 0.9*6.25*8.4[mm] 2 *0.275[KN/mm2] = [KN] Eq. J10-1 Local web yielding [KN] D Eq. J10-2 IsBeamReaction False N = N = 7[mm] Sec. J10-2 IsMemberEnd False R n = *(5*k + N)*F yw *t w = 1*(5*16[mm] + 7[mm])*0.275[KN/mm2]*6[mm] = [KN] Eq. J10-2 Web crippling [KN] D Eq. J10-4
6 IsBeamReaction False N = N = 7[mm] Sec. J10-2 R n = *0.80*t w 2 *(1 + 3*(N/d)*(t w /t f ) 1.5 )*(E*F yw *t f /t w ) 1/2 = 0.75*0.80* 6[mm] 2 *(1 + 3*(7[mm]/257.2[mm])*(6[mm]/8.4[mm]) 1.5 )*(205[KN/mm2]*0.275[KN/mm2]*8.4[mm]/ 6[mm]) 1/2 = [KN] Eq. J10-4 Support TOP FLANGE Flexural yielding [KN*m] D DG4 Eq. 3.20, Sec , DG4 Eq c = p f0 + p fi + t bf = [mm] + 40[mm] + 8.4[mm] = [mm] DG4 Table 3.4, AISC Table 6.5 s = 0.5*(b p *g) 1/2 = 0.5*(101.6[mm]*65[mm]) 1/2 = [mm] DG16 Table 3-2 Y c = b cf *(h 1 /s) + 4/g*(h 1 *s) = 101.6[mm]*(458.8[mm]/ [mm]) + 4/65[mm]*(458.8[mm]* [mm]) = [mm] DG16 Table 3-2 M n = F yc *Y c *t 2 cf = 0.275[KN/mm2]* [mm]*7[mm] 2 = [KN*m] DG4 Eq. 3.20, Sec M n = *M n = 0.9* [KN*m] = [KN*m] DG4 Eq Support bolt bearing [KN] D Eq. J3-6 L c-end = max(0.0, L e - d h /2) = max(0.0, 1E303[mm] [mm]/2) = 1E303[mm] Sec. J4.10 L c-spa = max(0.0, s - d h ) = max(0.0, 0[mm] [mm]) = 0[mm] Sec. J4.10 R n = *(min(k 1 *L c-end, k 2 *d) + min(k 1 *L c-spa, k 2 *d)*(n - 1))*t p *F u * n c = 0.75*(min(1.2*1E303[mm], 2.4*20[mm]) + min(1.2*0[mm], 2.4*20[mm])*(1-1))*7[mm]*0.415[KN/ mm2]*2 = [KN] Eq. J3-6 BOTTOM FLANGE Flexural yielding [KN*m] D DG4 Eq. 3.20, Sec , DG4 Eq c = p f0 + p fi + t bf = [mm] + 40[mm] [mm] = [mm] DG4 Table 3.4, AISC Table 6.5 s = 0.5*(b p *g) 1/2 = 0.5*(101.6[mm]*65[mm]) 1/2 = [mm] DG16 Table 3-2 Y c = b cf /2*((1/s)*(h 1 + h 2 )) + 2/g*(h 1 *(s *p b ) + h 2 *(s *p b )) + g/ 2 = 101.6[mm]/2*((1/ [mm])*(459.37[mm] [mm])) + 2/65[mm]*(459.37[mm]*( [mm] *70[mm]) [mm]*( [mm] *70[mm])) + 65[mm]/2 = [mm] DG16 Table 3-3 M n = F yc *Y c *t 2 cf = 0.275[KN/mm2]* [mm]*7[mm] 2 = [KN*m] DG4 Eq. 3.20, Sec M n = *M n = 0.9* [KN*m] = [KN*m] DG4 Eq Support bolt bearing [KN] D Eq. J3-6 L c-end = max(0.0, L e - d h /2) = max(0.0, 70[mm] [mm]/2) = [mm] Sec. J4.10 L c-spa = max(0.0, s - d h ) = max(0.0, 70[mm] [mm]) = [mm] Sec. J4.10 R n = *(min(k 1 *L c-end, k 2 *d) + min(k 1 *L c-spa, k 2 *d)*(n - 1))*t p *F u * n c = 0.75*(min(1.2* [mm], 2.4*20[mm]) + min(1.2* [mm], 2.4*20[mm])*(2-1))*7[mm]* 0.415[KN/mm2]*2 = [KN] Eq. J3-6 Panel web shear [KN] D Sec. J10-6, Eq. J10-9 P c = *F y *A = 1*0.275[KN/mm2]*3160[mm2] = 869[KN] Sec. J10-6 IsPanelZoneDeformationConsidered = IsPanelZoneDeformationConsidered = False Sec. J10-6 P r <=0.4*P c 0[KN]<=0.4*869[KN] True R n = *0.60*F y *d c *t w = 0.9*0.60*0.275[KN/mm2]*305.1[mm]*5.8[mm] = [KN] Eq. J10-9
7 Local web yielding [KN] D DG4 eq IsBeamReaction False N = N = 8.4[mm] Sec. J10-2 IsMemberEnd False R n = *1*(6*k + N + 2*t p )*F yw *t w = 1*1*(6*14.6[mm] + 8.4[mm] + 2*20[mm])*0.275[KN/ mm2]*5.8[mm] = [KN] DG4 eq Top web bearing [KN] D Eq. J10-4 IsBeamReaction False N = N = 8.4[mm] Sec. J10-2 R n = *0.80*t 2 w *(1 + 3*(N/d)*(t w /t f ) 1.5 )*(E*F yw *t f /t w ) 1/2 = 0.75*0.80* 5.8[mm] 2 *(1 + 3*(8.4[mm]/305.1[mm])*(5.8[mm]/7[mm]) 1.5 )*(205[KN/mm2]*0.275[KN/mm2]*7[mm]/ 5.8[mm]) 1/2 = [KN] Eq. J Critical strength ratio NOTATION A: Column cross-sectional area A b: Nominal bolt area A g: Gross area A w: Effective area of the weld b cf: Width of column flange b fb: Beam flange breadth b p: Plate width N: Bearing length C 2: Edge distance increment c: Vertical bolt spacing d: Nominal bolt diameter d bmax: Maximum bolt diameter d h: Nominal hole dimension d: Beam depth d c: Column depth D: Number of sixteenths of an inch in the weld size E: Elastic modulus F cr: Critical stress, flexural stress buckling F e: Elastic critical buckling stress F EXX: Electrode classification number F nt: Nominal tensile stress F nv: Nominal shear stress F u: Specified minimum tensile strength F w: Nominal strength of the weld metal per unit area F y: Specified minimum yield stress F yc: Specified minimum yield stress of column material F yf: Specified minimum yield stress of flange F yp: Specified minimum yield stress of plate F yw: Specified minimum yield stress of web g: Transversal gage between bolts g max: Maximum bolt gage g min: Minimum bolt gage IsBeamReaction: Is beam reaction IsMemberEnd: Is member end IsPanelZoneDeformationConsidered: Is panel zone deformation considered on frame stability K: Effective length factor k 1: Bearing factor k 1c: Distance from column web centerline to flange toe of fillet k 2: Bearing factor k: Distance from outer face of flange to the web toe of fillet k: Outside corner radius L: Length L c-end: Clear distance L e: Edge distance L emax: Maximum edge distance
8 L emin: Minimum edge distance L p: Plate length L: Length of weld LoadAngleFactor: Load angle factor M n: Nominal moment M np: No prying moment M pl: End plate or column flange flexural strength e dmin: Minimum edge distance n: Bolts rows number N: Bearing length n c: Number of bolt columns p b: Pitch between the inner and the outer row of bolts P c: Available axial compressive strength p f0: Distance from the inside of a beam tension flange to the nearest outside bolt row p fi: Distance from the inside of a beam tension flange to the nearest inside bolt row p fmin: Minimum distance from the inside of a beam tension flange to the nearest inside bolt row P r: Required axial stress P t: Bolt tensile strength : Design factors b: Design factor for bending M n: P n: R n: R n: R w: Design or allowable strength Design or allowable strength Design or allowable strength Design or allowable strength per unit length Fillet weld capacity per unit length R wl: Longitudinal fillet welds capacity Q: Prying action coefficient r: Radius of gyration s: Distance from the most inside or outside tension bolt row to the edge of a yield line s min: Minimum spacing s: Longitudinal bolt spacing L c-spa: Distance between adjacent holes edges t p: Thickness of the connected material T b: Minimum fastener pretension t bf: Thickness of the flange t cf: Thickness of the column flange t f: Thickness of the loaded flange t p: Plate thickness t w: Web thickness t wb: Thickness of beam web : Load angle w min: Minimum weld size required w: Weld size Y c: Column yield line mechanism parameter Y p: Yield line mechanism parameter p f: Distance from the bolt centerline adjacent the beam tension flange to the near face of the beam tension flange h 1: Distance from the compression side of the beam to the farthest inner load-carrying bolt line h 2: Distance from the compression side of the beam to the second farthest inner load-carrying bolt line d 1: Distance from the center of the beam compression flange to the farthest inner load-carrying bolt centerline d 2: Distance from the center of the beam compression flange to the second farthest inner load-carrying bolt centerline r: Load factor to limit connection rotation at ultimate moment to 10% of simple span rotation IsFlushConnection: Is flush connection d n: Sum of all distances from centerline of compression flange to the nth bolt row Q maxi: Maximum possible prying force for interior bolts w': Width of end-plate per bolt minus the bolt hole diameter a i: Distance from the interior bolt centerline to the prying force F i': Flange force per bolt at the thin plate limit when calculating Qmaxi for end-plate configurations with large inner pitch distances M q: Connection strength for the limit state of bolt fracture with prying action ThinPlateYieldingApply: Thin plate behavior controlled by end-plate yielding apply ThickPlateSmallerBoltsBehaviorApply: Thick plate behavior controled by bolt rupturwe without prying action apply t preq: Required plate thickness discr: Discriminant under the root sign for the calculation of Qmaxi, Qmaxo M np: Moment strength of the plate for the limit state of flexural yielding
9 bmpl: M q: Moment strength of the bolt group for the limit state of bolt rupture without prying action Moment strength of the bolt group for the limit state of bolt rupture with prying action
PROFILE SIZES: CONNECTION FORCES BEAM : UB254X146X43 CONNECTION DETAIL: D b = mm W b = mm T b = mm t wb = 7.30 mm r b = 7.
PROFILE SIZES: BEAM : UB254X146X43 D b = 259.60 mm W b = 147.30 mm T b = 12.70 mm t wb = 7.30 mm r b = 7.60 mm COLUMN : UC254X254X73 D C = 254.00 mm W c = 254.00 mm T C = 14.20 mm t wc = 8.60 mm r C =
More informationKarbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi
Chapter 04 Structural Steel Design According to the AISC Manual 13 th Edition Analysis and Design of Compression Members By Dr. Jawad Talib Al-Nasrawi University of Karbala Department of Civil Engineering
More informationUNIVERSITY OF AKRON Department of Civil Engineering
UNIVERSITY OF AKRON Department of Civil Engineering 4300:401-301 July 9, 2013 Steel Design Sample Quiz 2 1. The W10 x 54 column shown has both ends pinned and consists of A992 steel (F y = 50 ksi, F u
More information(Round up to the nearest inch.)
Assignment 10 Problem 5.46 LRFD First, select the lightest weight W14 column. Use the recommended design value for K for the pinned-fixed support condition specified (ref. Commentary, Appendix 7, AISC
More informationPresented by: Civil Engineering Academy
Presented by: Civil Engineering Academy Structural Design and Material Properties of Steel Presented by: Civil Engineering Academy Advantages 1. High strength per unit length resulting in smaller dead
More informationAccordingly, the nominal section strength [resistance] for initiation of yielding is calculated by using Equation C-C3.1.
C3 Flexural Members C3.1 Bending The nominal flexural strength [moment resistance], Mn, shall be the smallest of the values calculated for the limit states of yielding, lateral-torsional buckling and distortional
More informationCHAPTER II EXPERIMENTAL INVESTIGATION
CHAPTER II EXPERIMENTAL INVESTIGATION 2.1 SCOPE OF TESTING The objective of this research is to determine the force distribution between the column web and stiffener when the column flanges are subjected
More informationDesign of Beams (Unit - 8)
Design of Beams (Unit - 8) Contents Introduction Beam types Lateral stability of beams Factors affecting lateral stability Behaviour of simple and built - up beams in bending (Without vertical stiffeners)
More informationdb = 23.7 in B C D 96 k bf = 8.97 in tf = in k = 1.09 in 13 Fy = 50 ksi Fu = 65 ksi Member A-B, Interior column: A E
line B1, second floor. t = thickness of connected part Pu = factored load to be resisted d = diameter of the bolt eb = one-half the depth of the beam, in. ec = one-half the depth of the column, in. Hub
More informationPURE BENDING. If a simply supported beam carries two point loads of 10 kn as shown in the following figure, pure bending occurs at segment BC.
BENDING STRESS The effect of a bending moment applied to a cross-section of a beam is to induce a state of stress across that section. These stresses are known as bending stresses and they act normally
More informationKarbala University College of Engineering Department of Civil Eng. Lecturer: Dr. Jawad T. Abodi
Chapter 05 Structural Steel Design According to the AISC Manual 13 th Edition Analysis and Design of Beams By Dr. Jawad Talib Al-Nasrawi University of Karbala Department of Civil Engineering 71 Introduction
More informationRESILIENT INFRASTRUCTURE June 1 4, 2016
RESILIENT INFRASTRUCTURE June 1 4, 016 A FORMULATED APPROACH TO CISC SHEAR CONNECTION RESISTANCE AND FLEXIBILITY DESIGN Josiah J. Matthews University of New Brunswick, Canada Kaveh Arjomandi University
More informationMechanics of Materials Primer
Mechanics of Materials rimer Notation: A = area (net = with holes, bearing = in contact, etc...) b = total width of material at a horizontal section d = diameter of a hole D = symbol for diameter E = modulus
More informationProject data Project name Project number Author Description Date 26/04/2017 Design code AISC dome anchor. Material.
Project data Project name Project number Author Description Date 26/04/2017 Design code AISC 360-10 Material Steel A36, A529, Gr. 50 Concrete 4000 psi dome anchor Connection Name Description Analysis Design
More informationAutodesk Robot Structural Analysis Professional 2014 Design of fixed beam-to-column connection EN :2005/AC:2009
Autodesk Robot Structural Analysis Professional 2014 Design of fixed beam-to-column connection EN 1993-1-8:2005/AC:2009 Ratio 0,44 GENERAL Connection no.: 24 Connection name: Ligação 2 Structure node:
More informationStructural Steelwork Eurocodes Development of A Trans-national Approach
Structural Steelwork Eurocodes Development of A Trans-national Approach Course: Eurocode Module 7 : Worked Examples Lecture 0 : Simple braced frame Contents: 1. Simple Braced Frame 1.1 Characteristic Loads
More informationPLATE GIRDERS II. Load. Web plate Welds A Longitudinal elevation. Fig. 1 A typical Plate Girder
16 PLATE GIRDERS II 1.0 INTRODUCTION This chapter describes the current practice for the design of plate girders adopting meaningful simplifications of the equations derived in the chapter on Plate Girders
More informationSHEAR CONNECTION: DESIGN OF W-SHAPE BEAM TO RECTANGULAR/SQUARE HSS COLUMN SHEAR PLATE CONNECTION
SHEAR CONNECTION: DESIGN OF W-SHAPE BEAM TO RECTANGULAR/SQUARE HSS COLUMN SHEAR PLATE CONNECTION CALCULATION FOR SHEAR CONNECTION 8.xmcd 1 of 30 I. DESIGN DATA AND LOAD ( LRFD - AISC 14th Edition ) COLUMN
More informationExperimental investigation on monotonic performance of steel curved knee braces for weld-free beam-to-column connections
Experimental investigation on monotonic performance of steel curved knee braces for weld-free beam-to-column connections *Zeyu Zhou 1) Bo Ye 2) and Yiyi Chen 3) 1), 2), 3) State Key Laboratory of Disaster
More informationRoadway Grade = m, amsl HWM = Roadway grade dictates elevation of superstructure and not minimum free board requirement.
Example on Design of Slab Bridge Design Data and Specifications Chapter 5 SUPERSTRUCTURES Superstructure consists of 10m slab, 36m box girder and 10m T-girder all simply supported. Only the design of Slab
More informationTension Members. ENCE 455 Design of Steel Structures. II. Tension Members. Introduction. Introduction (cont.)
ENCE 455 Design of Steel Structures II. Tension Members C. C. Fu, Ph.D., P.E. Civil and Environmental Engineering Department University of Maryland Tension Members Following subjects are covered: Introduction
More informationSHEAR CONNECTION: W BEAM WITH SHEAR PLATE ONE-WAY SHEAR CONNECTION TO W COLUMN WEB
1 of 18 SHEAR CONNECTION: W BEAM WITH SHEAR PLATE ONE-WAY SHEAR CONNECTION TO W COLUMN WEB Description:Detailed Report 17 2 of 18 I. DESIGN DATA AND LOADS (ASD-14th Edition) COLUMN PROPERTIES: W14X90 -
More informationFHWA Bridge Design Guidance No. 1 Revision Date: July 21, Load Rating Evaluation of Gusset Plates in Truss Bridges
FHWA Bridge Design Guidance No. 1 Revision Date: July 21, 2008 Load Rating Evaluation of Gusset Plates in Truss Bridges By Firas I. Sheikh Ibrahim, PhD, PE Part B Gusset Plate Resistance in Accordance
More informationENCE 455 Design of Steel Structures. III. Compression Members
ENCE 455 Design of Steel Structures III. Compression Members C. C. Fu, Ph.D., P.E. Civil and Environmental Engineering Department University of Maryland Compression Members Following subjects are covered:
More informationGeneral Comparison between AISC LRFD and ASD
General Comparison between AISC LRFD and ASD 1 General Comparison between AISC LRFD and ASD 2 AISC ASD and LRFD AISC ASD = American Institute of Steel Construction = Allowable Stress Design AISC Ninth
More informationA CONNECTION ELEMENT FOR MODELLING END-PLATE CONNECTIONS IN FIRE
A CONNECTION ELEMENT OR MODELLING END-PLATE CONNECTIONS IN IRE Dr Zhaohui Huang Department of Civil & Structural Engineering, University of Sheffield 22 September 29 1. INTRODUCTION Three approaches for
More informationStructural Steelwork Eurocodes Development of A Trans-national Approach
Structural Steelwork Eurocodes Development of A Trans-national Approach Course: Eurocode 3 Module 7 : Worked Examples Lecture 20 : Simple braced frame Contents: 1. Simple Braced Frame 1.1 Characteristic
More information7.3 Design of members subjected to combined forces
7.3 Design of members subjected to combined forces 7.3.1 General In the previous chapters of Draft IS: 800 LSM version, we have stipulated the codal provisions for determining the stress distribution in
More informationAn Increase in Elastic Buckling Strength of Plate Girder by the Influence of Transverse Stiffeners
GRD Journals- Global Research and Development Journal for Engineering Volume 2 Issue 6 May 2017 ISSN: 2455-5703 An Increase in Elastic Buckling Strength of Plate Girder by the Influence of Transverse Stiffeners
More informationMODULE F: SIMPLE CONNECTIONS
MODULE F: SIMPLE CONNECTIONS This module of CIE 428 covers the following subjects Connector characterization Failure modes of bolted shear connections Detailing of bolted connections Bolts: common and
More informationAppendix J. Example of Proposed Changes
Appendix J Example of Proposed Changes J.1 Introduction The proposed changes are illustrated with reference to a 200-ft, single span, Washington DOT WF bridge girder with debonded strands and no skew.
More information3. Stability of built-up members in compression
3. Stability of built-up members in compression 3.1 Definitions Build-up members, made out by coupling two or more simple profiles for obtaining stronger and stiffer section are very common in steel structures,
More informationCO~RSEOUTL..INE. revisedjune 1981 by G. Frech. of..a.pqij~t(..~ttsa.fidteconol.q.gy. Sault ",Ste'...:M~ri,e.: SAUl. ir.ft\,nl~t';~l' G ". E b:.
-/ 1/ /.. SAUl. ir.ft\,nl~t';~l' G ". E b:.~~~~~, of..a.pqij~t(..~ttsa.fidteconol.q.gy. Sault ",Ste'...:M~ri,e.: ',' -.\'~. ~ ;:T.., CO~RSEOUTL..INE ARCHITECTURAL ENGINEERING II ARC 200-4 revisedjune 1981
More informationGENERAL GEOMETRY LEFT SIDE BEAM RIGHT SIDE BS :2000/AC:2009. Ratio 0.17
Autodesk Robot Structural Analysis Professional 2015 Design of fixed beam-to-beam connection BS 5950-1:2000/AC:2009 Ratio 0.17 GENERAL Connection no.: 2 Connection name: Beam-Beam Structure node: 40 Structure
More information[5] Stress and Strain
[5] Stress and Strain Page 1 of 34 [5] Stress and Strain [5.1] Internal Stress of Solids [5.2] Design of Simple Connections (will not be covered in class) [5.3] Deformation and Strain [5.4] Hooke s Law
More informationJob No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet. Member Design - Steel Composite Beam XX 22/09/2016
CONSULTING Engineering Calculation Sheet jxxx 1 Member Design - Steel Composite Beam XX Introduction Chd. 1 Grade 50 more common than Grade 43 because composite beam stiffness often 3 to 4 times non composite
More informationCompression Members. ENCE 455 Design of Steel Structures. III. Compression Members. Introduction. Compression Members (cont.)
ENCE 455 Design of Steel Structures III. Compression Members C. C. Fu, Ph.D., P.E. Civil and Environmental Engineering Department University of Maryland Compression Members Following subjects are covered:
More informationPERFORATED METAL DECK DESIGN
PERFORATED METAL DECK DESIGN with Commentary Prepared By: L.D. Luttrell, Technical Advisor Steel Deck Institute November 18, 2011 Copyright 2011 All rights reserved P.O. Box 25 Fox River Grove, IL 60021
More informationAn investigation of the block shear strength of coped beams with a welded. clip angles connection Part I: Experimental study
An investigation of the block shear strength of coped beams with a welded clip angles connection Part I: Experimental study Michael C. H. Yam a*, Y. C. Zhong b, Angus C. C. Lam b, V. P. Iu b a Department
More informationUNIT III DEFLECTION OF BEAMS 1. What are the methods for finding out the slope and deflection at a section? The important methods used for finding out the slope and deflection at a section in a loaded
More informationApplication nr. 7 (Connections) Strength of bolted connections to EN (Eurocode 3, Part 1.8)
Application nr. 7 (Connections) Strength of bolted connections to EN 1993-1-8 (Eurocode 3, Part 1.8) PART 1: Bolted shear connection (Category A bearing type, to EN1993-1-8) Structural element Tension
More informationApplication nr. 3 (Ultimate Limit State) Resistance of member cross-section
Application nr. 3 (Ultimate Limit State) Resistance of member cross-section 1)Resistance of member crosssection in tension Examples of members in tension: - Diagonal of a truss-girder - Bottom chord of
More informationON THE DESIGN OF A STEEL END-PLATE BEAM-TO-COLUMN BOLTED JOINT ACCORDING TO PN-EN
CZASOPISMO INŻYNIERII LĄDOWEJ, ŚRODOWISKA I ARCHITEKTURY JOURNAL O CIVIL ENGINEERING, ENVIRONMENT AND ARCHITECTURE JCEEA, t. XXXV, z. 65 (2/18), kwiecień-czerwiec 2018, s. 187-196, DOI:10.7862/rb.2018.35
More informationtwenty steel construction: columns & tension members ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS FALL 2013 lecture
ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS Cor-Ten Steel Sculpture By Richard Serra Museum of Modern Art Fort Worth, TX (AISC - Steel Structures of the Everyday) FALL 2013 lecture
More informationStructural Steelwork Eurocodes Development of a Trans-National Approach
Course: Eurocode 4 Structural Steelwork Eurocodes Development of a Trans-National Approach Lecture 9 : Composite joints Annex B References: COST C1: Composite steel-concrete joints in frames for buildings:
More informationJointsForTekla Ver January
Ing. Giovanni Conticello Ing. Sebastiano Floridia With the important help of Ing. Giovanni Trigili JointsForTekla Ver. 1.11.0.59 - January 23 2014 Design of joints of steel structures in environment TeklaStructures
More informationε t increases from the compressioncontrolled Figure 9.15: Adjusted interaction diagram
CHAPTER NINE COLUMNS 4 b. The modified axial strength in compression is reduced to account for accidental eccentricity. The magnitude of axial force evaluated in step (a) is multiplied by 0.80 in case
More informationChapter. Materials. 1.1 Notations Used in This Chapter
Chapter 1 Materials 1.1 Notations Used in This Chapter A Area of concrete cross-section C s Constant depending on the type of curing C t Creep coefficient (C t = ε sp /ε i ) C u Ultimate creep coefficient
More informationSteel Structures Design and Drawing Lecture Notes
Steel Structures Design and Drawing Lecture Notes INTRODUCTION When the need for a new structure arises, an individual or agency has to arrange the funds required for its construction. The individual or
More information2012 MECHANICS OF SOLIDS
R10 SET - 1 II B.Tech II Semester, Regular Examinations, April 2012 MECHANICS OF SOLIDS (Com. to ME, AME, MM) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~
More informationSteel Design. Notation:
Steel Design Notation: a A A b A e A g A gv A n A nt A nv A w = name for width dimension = name for area = area of a bolt = effective net area found from the product of the net area A n by the shear lag
More informationBeam Bending Stresses and Shear Stress
Beam Bending Stresses and Shear Stress Notation: A = name or area Aweb = area o the web o a wide lange section b = width o a rectangle = total width o material at a horizontal section c = largest distance
More informationTORSION INCLUDING WARPING OF OPEN SECTIONS (I, C, Z, T AND L SHAPES)
Page1 TORSION INCLUDING WARPING OF OPEN SECTIONS (I, C, Z, T AND L SHAPES) Restrained warping for the torsion of thin-wall open sections is not included in most commonly used frame analysis programs. Almost
More informationQUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS
QUESTION BANK SEMESTER: III SUBJECT NAME: MECHANICS OF SOLIDS UNIT 1- STRESS AND STRAIN PART A (2 Marks) 1. Define longitudinal strain and lateral strain. 2. State Hooke s law. 3. Define modular ratio,
More informationSIMPLE MODEL FOR PRYING FORCES IN T-HANGER CONNECTIONS WITH SNUG TIGHTENED BOLTS
SIMPLE MODEL FOR PRYING FORCES IN T-HANGER CONNECTIONS WITH SNUG TIGHTENED BOLTS By Fathy Abdelmoniem Abdelfattah Faculty of Engineering at Shoubra, Zagazig University, Banha Branch Mohamed Salah A. Soliman
More informationCHAPTER 4. Stresses in Beams
CHAPTER 4 Stresses in Beams Problem 1. A rolled steel joint (RSJ) of -section has top and bottom flanges 150 mm 5 mm and web of size 00 mm 1 mm. t is used as a simply supported beam over a span of 4 m
More informationAPRIL Conquering the FE & PE exams Formulas, Examples & Applications. Topics covered in this month s column:
APRIL 2015 DR. Z s CORNER Conquering the FE & PE exams Formulas, Examples & Applications Topics covered in this month s column: PE Exam Specifications (Geotechnical) Transportation (Horizontal Curves)
More informationdb = 23.7 in B C D 96 k bf = 8.97 in tf = in k = 1.09 in 13 Fy = 50 ksi Fu = 65 ksi Member A-B, Interior column: A E
le B1, second floor. t = thickness of connected part Pu = factored load to be resisted d = diameter of the bolt eb = one-half the depth of the beam, ec = one-half the depth of the column, Hub = factored
More informationCONNECTION DESIGN. Connections must be designed at the strength limit state
CONNECTION DESIGN Connections must be designed at the strength limit state Average of the factored force effect at the connection and the force effect in the member at the same point At least 75% of the
More informationCIVIL DEPARTMENT MECHANICS OF STRUCTURES- ASSIGNMENT NO 1. Brach: CE YEAR:
MECHANICS OF STRUCTURES- ASSIGNMENT NO 1 SEMESTER: V 1) Find the least moment of Inertia about the centroidal axes X-X and Y-Y of an unequal angle section 125 mm 75 mm 10 mm as shown in figure 2) Determine
More informationSKILLS Project. October 2013
SKILLS Project October 2013 MOMENT CONNECTIONS PART 1 LEARNING OUTCOMES Design process for moment-resisting bolted connections Joint moment resistance Joint stiffness Details design (welds, bolts, stiffeners,
More information2. (a) Explain different types of wing structures. (b) Explain the advantages and disadvantages of different materials used for aircraft
Code No: 07A62102 R07 Set No. 2 III B.Tech II Semester Regular/Supplementary Examinations,May 2010 Aerospace Vehicle Structures -II Aeronautical Engineering Time: 3 hours Max Marks: 80 Answer any FIVE
More informationPurpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on Exam 3.
ES230 STRENGTH OF MTERILS Exam 3 Study Guide Exam 3: Wednesday, March 8 th in-class Updated 3/3/17 Purpose of this Guide: To thoroughly prepare students for the exact types of problems that will be on
More informationThe subject of this paper is the development of a design
The erformance and Design Checking of Chord-Angle Legs in Joist Girders THEODORE V. GALAMBOS ABSTRACT The subject of this paper is the development of a design checking method for the capacity of the outstanding
More informationtwenty one concrete construction: shear & deflection ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture
ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture twenty one concrete construction: Copyright Kirk Martini shear & deflection Concrete Shear 1 Shear in Concrete
More informationBasis of Design, a case study building
Basis of Design, a case study building Luís Simões da Silva Department of Civil Engineering University of Coimbra Contents Definitions and basis of design Global analysis Structural modeling Structural
More informationDesign of Steel Structures Prof. S.R.Satish Kumar and Prof. A.R.Santha Kumar. Local buckling is an extremely important facet of cold formed steel
5.3 Local buckling Local buckling is an extremely important facet of cold formed steel sections on account of the fact that the very thin elements used will invariably buckle before yielding. Thinner the
More informationSAULTCOLLEGE of AppliedArtsand Technology SaultSte. Marie COURSEOUTLINE
SAULTCOLLEGE of AppliedArtsand Technology SaultSte. Marie COURSEOUTLINE STRENGTH OF ~1ATERIALS MCH 103-3 revised June 1981 by W.J. Adolph ------- STRENGHT OF MATERIALS MCH 103-3 To'Cic Periods Tooic Description
More informationBASE PLATE CONNECTIONS
SKILLS Project BASE PLATE CONNECTIONS LEARNING OUTCOMES Design process for pinned and fixed column base joints Base-plate resistance Anchor bolt resistance Concrete resistance Weld resistance Application
More informationExternal Pressure... Thermal Expansion in un-restrained pipeline... The critical (buckling) pressure is calculated as follows:
External Pressure... The critical (buckling) pressure is calculated as follows: P C = E. t s ³ / 4 (1 - ν ha.ν ah ) R E ³ P C = Critical buckling pressure, kn/m² E = Hoop modulus in flexure, kn/m² t s
More informationCurved Steel I-girder Bridge LFD Guide Specifications (with 2003 Edition) C. C. Fu, Ph.D., P.E. The BEST Center University of Maryland October 2003
Curved Steel I-girder Bridge LFD Guide Specifications (with 2003 Edition) C. C. Fu, Ph.D., P.E. The BEST Center University of Maryland October 2003 Guide Specifications (1993-2002) 2.3 LOADS 2.4 LOAD COMBINATIONS
More informationCHAPTER 2 LITERATURE REVIEW
8 CHAPTER 2 LITERATURE REVIEW 2.1 GENERAL A brief review of the research carried out during the past years related to the behaviour of bolted steel angle tension members is presented herewith. Literature
More informationTRANSVERSE PLATE-TO-SQUARE/RECTANGULAR HSS CONNECTIONS
TRANSVERSE PLATE-TO-SQUARE/RECTANGULAR HSS CONNECTIONS by Jeffrey A. Packer 1 1 Bahen/Tanenbaum Professor of Civil Engineering, University of Toronto, Ontario, Canada Some of the common types of plate-to-rectangular
More informationUnified Design Criteria for Steel Cantilever Plate Connection Elements. Pouya Salem
Unified Design Criteria for Steel Cantilever Plate Connection Elements by Pouya Salem A thesis submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy in STRUCTURAL
More informationMODULE C: COMPRESSION MEMBERS
MODULE C: COMPRESSION MEMBERS This module of CIE 428 covers the following subjects Column theory Column design per AISC Effective length Torsional and flexural-torsional buckling Built-up members READING:
More informationDesign of Shear Tab Connections for Gravity and Seismic Loads
June 2005 Design of Shear Tab Connections for Gravity and Seismic Loads By Abolhassan Astaneh-Asl, Ph.D., P.E. Professor University of California, Berkeley (A copy of this report can be downloaded for
More informationDelhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web: Ph:
Serial : IG1_CE_G_Concrete Structures_100818 Delhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web: E-mail: info@madeeasy.in Ph: 011-451461 CLASS TEST 018-19 CIVIL ENGINEERING
More informationSteel Post Load Analysis
Steel Post Load Analysis Scope The steel posts in 73019022, 73019024, and 73019025, are considered to be traditional building products. According to the 2015 International Building Code, this type of product
More informationThe plastic moment capacity of a composite cross-section is calculated in the program on the following basis (BS 4.4.2):
COMPUTERS AND STRUCTURES, INC., BERKELEY, CALIFORNIA SEPTEMBER 2002 COMPOSITE BEAM DESIGN BS 5950-90 Technical Note Composite Plastic Moment Capacity for Positive Bending This Technical Note describes
More information: APPLIED MECHANICS & STRENGTH OF MATERIALS COURSE CODE : 4021 COURSE CATEGORY : A PERIODS/ WEEK : 5 PERIODS/ SEMESTER : 75 CREDIT : 5 TIME SCHEDULE
COURSE TITLE : APPLIED MECHANICS & STRENGTH OF MATERIALS COURSE CODE : 4021 COURSE CATEGORY : A PERIODS/ WEEK : 5 PERIODS/ SEMESTER : 75 CREDIT : 5 TIME SCHEDULE MODULE TOPIC PERIODS 1 Simple stresses
More information林保均 / Pao-Chun Lin. National Center for Research on Earthquake Engineering M.S. / Civil Engineering Department, National Taiwan University
Seismic Design of WES-BRB and Gusset Connections 林保均 / Pao-Chun Lin Assistant Researcher National Center for Research on Earthquake Engineering M.S. / Civil Engineering Department, National Taiwan University
More informationUNIT-I STRESS, STRAIN. 1. A Member A B C D is subjected to loading as shown in fig determine the total elongation. Take E= 2 x10 5 N/mm 2
UNIT-I STRESS, STRAIN 1. A Member A B C D is subjected to loading as shown in fig determine the total elongation. Take E= 2 x10 5 N/mm 2 Young s modulus E= 2 x10 5 N/mm 2 Area1=900mm 2 Area2=400mm 2 Area3=625mm
More information3 Hours/100 Marks Seat No.
*17304* 17304 14115 3 Hours/100 Marks Seat No. Instructions : (1) All questions are compulsory. (2) Illustrate your answers with neat sketches wherever necessary. (3) Figures to the right indicate full
More informationStructural Steelwork Eurocodes Development of A Trans-national Approach
Structural Steelwork Eurocodes Development of A Trans-national Approach Course: Eurocode Module 7 : Worked Examples Lecture 22 : Design of an unbraced sway frame with rigid joints Summary: NOTE This example
More informationBLOCK SHEAR BEHAVIOUR OF COPED STEEL BEAMS
University of Alberta Department of Civil & Environmental Engineering Structural Engineering Report No. 244 BLOCK SHEAR BEHAVIOUR OF COPED STEEL BEAMS by Cameron R. Franchuk Robert G. Driver and Gilbert
More informationThe University of Melbourne Engineering Mechanics
The University of Melbourne 436-291 Engineering Mechanics Tutorial Four Poisson s Ratio and Axial Loading Part A (Introductory) 1. (Problem 9-22 from Hibbeler - Statics and Mechanics of Materials) A short
More informationSeismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design
Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design Elmer E. Marx, Alaska Department of Transportation and Public Facilities Michael Keever, California Department
More informationJob No. Sheet 1 of 6 Rev B. Made by IR Date Oct Checked by FH/NB Date Oct Revised by MEB Date April 2006
Job No. Sheet 1 of 6 Rev B, Route de Limours Tel : (0)1 0 85 5 00 Fax : (0)1 0 5 75 8 Revised by MEB Date April 006 DESIGN EXAMPLE 6 BOLTED JOINT A 0 0 angle loaded in tension is to be connected to a gusset
More informationUnfinished Bolt ordinary, common, rough or black bolts High strength Bolt friction type bolts
Bolted Connections Introductions: Connections are always needed to connect two members. It is necessary to ensure functionality and compactness of structures. Prime role of connections is to transmit force
More informationCOURSE TITLE : APPLIED MECHANICS & STRENGTH OF MATERIALS COURSE CODE : 4017 COURSE CATEGORY : A PERIODS/WEEK : 6 PERIODS/ SEMESTER : 108 CREDITS : 5
COURSE TITLE : APPLIED MECHANICS & STRENGTH OF MATERIALS COURSE CODE : 4017 COURSE CATEGORY : A PERIODS/WEEK : 6 PERIODS/ SEMESTER : 108 CREDITS : 5 TIME SCHEDULE MODULE TOPICS PERIODS 1 Simple stresses
More informationJUT!SI I I I TO BE RETURNED AT THE END OF EXAMINATION. THIS PAPER MUST NOT BE REMOVED FROM THE EXAM CENTRE. SURNAME: FIRST NAME: STUDENT NUMBER:
JUT!SI I I I TO BE RETURNED AT THE END OF EXAMINATION. THIS PAPER MUST NOT BE REMOVED FROM THE EXAM CENTRE. SURNAME: FIRST NAME: STUDENT NUMBER: COURSE: Tutor's name: Tutorial class day & time: SPRING
More informationLOAD BEARING CAPACITY OF SPLICED COLUMNS WITH SINGLE ROW BOLTED BUTT-PLATES
LOAD BEARING CAPACITY OF SPLICED COLUMNS WITH SINGLE ROW BOLTED BUTT-PLATES J.C.D. Hoenderkamp, H. H. Snijder Eindhoven University of Technology, The Netherlands j.c.d.hoenderkamp@tue.nl h.h.snijder@tue.nl
More informationAPPENDIX 1 MODEL CALCULATION OF VARIOUS CODES
163 APPENDIX 1 MODEL CALCULATION OF VARIOUS CODES A1.1 DESIGN AS PER NORTH AMERICAN SPECIFICATION OF COLD FORMED STEEL (AISI S100: 2007) 1. Based on Initiation of Yielding: Effective yield moment, M n
More informationSECTION 7 DESIGN OF COMPRESSION MEMBERS
SECTION 7 DESIGN OF COMPRESSION MEMBERS 1 INTRODUCTION TO COLUMN BUCKLING Introduction Elastic buckling of an ideal column Strength curve for an ideal column Strength of practical column Concepts of effective
More informationSupplement: Statically Indeterminate Trusses and Frames
: Statically Indeterminate Trusses and Frames Approximate Analysis - In this supplement, we consider an approximate method of solving statically indeterminate trusses and frames subjected to lateral loads
More informationDESIGN OF BEAMS AND SHAFTS
DESIGN OF EAMS AND SHAFTS! asis for eam Design! Stress Variations Throughout a Prismatic eam! Design of pristmatic beams! Steel beams! Wooden beams! Design of Shaft! ombined bending! Torsion 1 asis for
More informationLecture-04 Design of RC Members for Shear and Torsion
Lecture-04 Design of RC Members for Shear and Torsion By: Prof. Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk www.drqaisarali.com 1 Topics Addressed Design of
More informationSteel Design. Notation: a A A b A e
Steel Design Notation: a A A b A e A g A gv A n A nt A nv A w = name for width dimension = name for area = area of a bolt = effective net area found from the product of the net area A n by the shear lag
More informationDesign of Steel Structures Prof. S.R.Satish Kumar and Prof. A.R.Santha Kumar
5.10 Examples 5.10.1 Analysis of effective section under compression To illustrate the evaluation of reduced section properties of a section under axial compression. Section: 00 x 80 x 5 x 4.0 mm Using
More informationChapter Objectives. Design a beam to resist both bendingand shear loads
Chapter Objectives Design a beam to resist both bendingand shear loads A Bridge Deck under Bending Action Castellated Beams Post-tensioned Concrete Beam Lateral Distortion of a Beam Due to Lateral Load
More information