Modelling of temperature profiles in Nd:YAG laser annealed GaAs/AlGaAs quantum well microstructures
|
|
- Hortense Edwards
- 5 years ago
- Views:
Transcription
1 Modelling of temperature profiles in Nd:YG laser annealed Gas/lGas quantum well microstructures Radoslaw Stanowski Ph.D. O. Voznyy prof. J J. Dubowski 1
2 Outline 1. Motivation 2. Transient temperature analysis 3. Experiment 4. Calculated temperature profiles 5. Summary 2
3 Motivation Manufacturing of Photonics Integrated Circuits requires spatialy-selective areas of dedicated QW s energy bandgap width. Regrowth with simultaneous etching using masks is an expensive approach. Post-growth selective-area bandgap tuning by direct Nd:YG (1064nm) laser irradiation (LRT-laser rapid thermal annealing) is an attractive and cost-efective approach to fabricate monolithically integrated photonic devices. Schematic diagam illustating the effect of well/barrier interdiffusion on the shape and bandgap energy of quantum wells. from: Semiconductor Quantum Wells Intermixing, edited by E. Herbert Li 3
4 QWI technique Laser induced QWI techniques 1. PID photoabsorption disordering 2. Impurity free vacancy disordering 3. Melting - complete intermixing 4. LRT Laser Rapid Thermal nnealing lgas/gas Room temperature emission spectra of as-grown and bandgap shifted broad area Fabry-Perot laser diodes. from: Semiconductor Quantum Wells Intermixing, edited by E. Herbert Li Picture of conduction and valance band shows the confined states change with annealing 4
5 FEM Finite Element Method FEM general idea description: Geometry For calculations we have used FEMLB 3.0a (multiphysics problems solver) Heat transfer module Geometry PDE - Partial Differential Equation Material parameters Center Radius length 5
6 Heat Transfer PDE : Subdomain equation: Q - (k T) = ρc p ( T/ T/ t) k thermal conductivity tensor [W/(m K)] T temperature [K] ρ - density [kg/m 3 ] C p heat capacity [J/(kg K)] Boundary equation: square k T T = q 0 + h (T inf T) + Const (T 4 amb T 4 ) k heat transfer T T inf Temperature close to the surface (heat convection) [K] T amb mbient Temperature (heat radiation) [K] q Invard flux [W/m 2 ] h convection coefficient [W/(m K)] Const emissivity*sigma(stefan Boltzman s heat radiation constant) Q heat source (or sink) [W] = (1-R) R) Imax_square beam_shape_ Center square absorption exp( exp(-absorption z) Boundary Subdomain Radius length Incident LSER beam 6
7 Material parameters: ssumed temperature independent: k thermal conductivity = 16280/T [W/(m K)] α optical absorption = T [cm-1], ssumed temperature dependent: ε = 0.4 Cp= 325 [J/kg K] ρ = 5317 [kg/m3] h = 20 [W/(m K)] Diameter = φ = [m] Thickness = [m] Center Radius length 7
8 Thermal conductivity - k k = 16280/T [W/m K], for T = 300 [K], k = 56 [W /m K], for T = [K], k = 20 [W /m K], for T = [K], k = 15 [W /m K] T k k=16280/t W/(mK) k=56 W/(mK) time [s] Center Radius length Transient temperature in the middle of laser irradiated spot 8
9 Optical absorption - α α = T [cm -1 ], for T= 300 [K], α = 3 [cm -1 ], for T= [K], α = 12,495 [cm -1 ], for T= [K], α = 19,991 [cm -1 ] T α α=20000 cm -1 or α= *t α= cm -1 α=100 cm -1 α=10 cm -1 α=3 cm -1 Over K the laser delivered energy is absorbed by the very first layers of the irradiated wafer time [s] Transient temperature in the middle of laser irradiated spot 9
10 Emissivity - ε ssumption of the ideal case of the black body radiation (ε = 1) results in the underestimation of the temperature. difference of 166 [K] in the saturation temperature is expected, if the surface of Gas capped with SiO 2 has its emissivity reduced to (ε = 0.4). emissivity=0.4 emissivity=0.6 emissivity=0.8 emissivity= Time [s] Transient temperature in the middle of laser irradiated spot 10
11 Experimental setup description 1. Gas wafer was coated on both sides with 270nm SiO 2 layers deposited in PVCVD reactor for both to act as an antirefractive coating and prevent from s decomposition from the annealed microstructure. 2. Sample was placed on three silica point shape ended rods to avoid big contacts with surround 3. t room ambient conditions without additional cooling or heatting 4. Convection and radiation was assumed constant during experiment 5. The Nd:YG laser delivered power density of 1W/mm 2 at the spot of 3mm diameter. 6. Temperature has been collected within 0.1s interval steps from area of about 7mm 2 (approx. 1.5mm diameter) 11
12 Modelling vs. Measurement Parameter / Material Laser beam power Laser beam diameter Reflected power Optical absorption Emissivity Convection Specific heat Thermal conductivity Density mbient temperature Wafer dimensions Wafer thickness Calculations φ = 9*10-3 [m] 7 [W] 3*10-3 [m] 10 % [W/m 2 ] 325 [J/kg K] 56 [W/m 296 [K] 16280/T [W/m K] 5317 [kg/m 3 ] 296 [K] (6*10-3 x 11*10-3 ) [m] 300µm Gas (capped with SiO 2 ) T [cm-1], for 300 [K] < T < [K] [cm-1], for T > [K] Center Temperature vs time in the middle of the laser irradiated zone Experiment Calculations Temperature measurement threshold = 1 [W/mm 2 ] Laser beam diameter = 3mm time [s] 12 Radius length
13 Calculated temperature profiles lateral resolution without background heating d=µm d=100µm Temperature vs Radius ( µm laser beam) vacuum room ambient wind cooling =5.9[W/mm 2 ] =7.9[W/mm 2 ] =13.3[W/mm 2 ] h=0 P=2.30W h=20 P=3.05W h=100 P=5.11W Temperature vs Radius (100 µm laser beam) h=0 P=0.79W h=20 P=1.08W h=100 P=1.52W =100[W/mm 2 ] =136[W/mm 2 ] Radius [µm] Radius [µm] =193[W/mm 2 ] Radius [µm] 13
14 Calculated temperature profiles lateral resolution with background heating d=µm d=100µm Temperature vs Radius ( µm laser beam) Temperature vs Radius (100 µm laser beam) =2.4[W/mm 2 ] =4.7[W/mm 2 ] =7.9[W/mm 2 ] Tsink=973K P=0.94W Tsink=773K P=1.83W Tsink=300K P=3.04W Tsink=973K P=0.22W Tsink=773K P=0.49W Tsink=300K P=1.08W =27[W/mm 2 ] =61[W/mm 2 ] =136[W/mm 2 ] Radius [µm] Radius [µm] Radius [µm] 14
15 Calculated temperature profiles in-depth resolution without background heating d=µm d=100µm Temperature in-depth of the sample ( µm laser beam) Temperature in-depth of the sample (100 µm laser beam) =5.9[W/mm 2 ] =7.9[W/mm 2 ] =13.3[W/mm 2 ] h=0 P=0.79W h=20 P=1.08W h=100 P=1.52W =100[W/mm 2 ] =136[W/mm 2 ] h=0 P=2.30W h=20 P=3.05W h=100 P=5.11W =193[W/mm 2 ] z-axis [µm] z-axis [µm] 15
16 Calculated temperature profiles in-depth resolution with background heating d=µm d=100µm Temperature in-depth of the sample ( µm laser beam) Temperature in-depth of the sample (100 µm laser beam) =2.4[W/mm 2 ] =4.7[W/mm 2 ] =7.9[W/mm 2 ] Tsink=973K P=0.22W Tsink=773K P=0.49W Tsink=300K P=1.08W =27[W/mm 2 ] =61[W/mm 2 ] Tsink=973K P=0.94W Tsink=773K P=1.83W Tsink=300K P=3.04W =136[W/mm 2 ] z-axis [µm] z-axis [µm] 16
17 Summary Finite Element Method calculations have been carried out to determine temperature profiles in Nd:YG (1064nm) laser irradiated Si and Gas wafers. Increasing thermal convection of the laser heated wafer leads to narrower temperature profiles, but higher power densities have to be used. Processing with decreasing laser beam diameter can lead to sharper temperature profiles. To maintain the incident laser beam intensity below the threshold of surface damage, background heating has to be introduced. Shallow temperature propagation has been observed for small laser beam diameters, thus depth at which Quantum Well is located is an important parameter to achieve high spatial resolution Quantum Well Intermixing Calculations describe reasonably well the measured transient temperature in the middle of irradiated zone on the wafer s surface. 17
18 Thank You for atten ua tion!!! Radoslaw Stanowski 18
Numerical Simulation of Si Nanosecond Laser Annealing by COMSOL Multiphysics
Excerpt from the Proceedings of the COMSOL Conference 28 Hannover Numerical Simulation of Si Nanosecond Laser Annealing by COMSOL Multiphysics M. Darif*, N. Semmar GREMI-UMR666, CNRS-Université d Orléans,
More informationChapter 7. Solar Cell
Chapter 7 Solar Cell 7.0 Introduction Solar cells are useful for both space and terrestrial application. Solar cells furnish the long duration power supply for satellites. It converts sunlight directly
More informationUniversity of New Mexico Mechanical Engineering Spring 2012 PhD qualifying examination Heat Transfer
University of New Mexico Mechanical Engineering Spring 2012 PhD qualifying examination Heat Transfer Closed book. Formula sheet and calculator are allowed, but not cell phones, computers or any other wireless
More informationSegmented 1.55um Laser with 400% Differential Quantum Efficiency J. Getty, E. Skogen, L. Coldren, University of California, Santa Barbara, CA.
Segmented 1.55um Laser with 400% Differential Quantum Efficiency J. Getty, E. Skogen, L. Coldren, University of California, Santa Barbara, CA. Abstract: By electrically segmenting, and series-connecting
More informationInternational Journal of Scientific & Engineering Research, Volume 8, Issue 2, February-2017 ISSN
ISSN 2229-5518 916 Laser Damage Effect Studies with Hollow Metallic Targets Satyender Kumar, S Jain, K C Sati, S Goyal, R Malhotra, R Rajan, N R Das & A K Srivastava Laser Science & Technology Centre Metcalfe
More informationINTRODUCTION Radiation differs from conduction and convection in that it does not require the presence of a material medium to take place.
RADIATION INTRODUCTION Radiation differs from conduction and convection in that it does not require the presence of a material medium to take place. Radiation: The energy emitted by matter in the form
More informationGe Quantum Well Modulators on Si. D. A. B. Miller, R. K. Schaevitz, J. E. Roth, Shen Ren, and Onur Fidaner
10.1149/1.2986844 The Electrochemical Society Ge Quantum Well Modulators on Si D. A. B. Miller, R. K. Schaevitz, J. E. Roth, Shen Ren, and Onur Fidaner Ginzton Laboratory, 450 Via Palou, Stanford CA 94305-4088,
More informationTransmissive Final Optic for Laser IFE
Transmissive Final Optic for Laser IFE S. A. Payne, J. F. Latkowski, A. Kubota, M. J. Caturla, S. N. Dixit, and J. A. Speth Lawrence Livermore National Laboratory April 4, 2002 HAPL Program Workshop General
More informationUnderstanding Semiconductor Lasers
27 April 2010 age 1 of 8 Experiment II Understanding Semiconductor Lasers The purpose of this experiment is to explore the basic characteristics of semiconductor lasers. We will measure and calculate the
More informationIntroduction to Semiconductor Integrated Optics
Introduction to Semiconductor Integrated Optics Hans P. Zappe Artech House Boston London Contents acknowledgments reface itroduction Chapter 1 Basic Electromagnetics 1 1.1 General Relationships 1 1.1.1
More informationComputational Study on the Effect of the Pulse Length on Laser Ablation Processes
Lasers in Manufacturing Conference 015 Computational Study on the Effect of the Pulse Length on Laser Ablation Processes "Stefan Tatra *, Rodrigo Gómez Vázquez, Andreas Otto" "Vienna University of Technology,
More informationAbnormal PL spectrum in InGaN MQW surface emitting cavity
Abnormal PL spectrum in InGaN MQW surface emitting cavity J. T. Chu a, Y.-J. Cheng b, H. C. Kuo a, T. C. Lu a, and S. C. Wang a a Department of Photonics & Institute of Electro-Optical Engineering, National
More informationNUMERICAL INVESTIGATION AND STATISTICAL ANALYSIS OF LASER BENDING OF TITANIUM SHEETS
5 th International & 26 th All India Manufacturing Technology, Design and Research Conference (AIMTDR 2014) December 12 th 14 th, 2014, IIT Guwahati, Assam, India NUMERICAL INVESTIGATION AND STATISTICAL
More informationHeat and Mass transfer in Reactive Multilayer Systems (RMS)
Heat and Mass transfer in Reactive Multilayer Systems (RMS) M. Rühl *1, G. Dietrich 2, E. Pflug 1, S. Braun 2 and A. Leson 2 1 TU-Dresden Institute of Manufacturing Technology, George-Bähr 3c, 01069 Dresden,
More informationLaser Basics. What happens when light (or photon) interact with a matter? Assume photon energy is compatible with energy transition levels.
What happens when light (or photon) interact with a matter? Assume photon energy is compatible with energy transition levels. Electron energy levels in an hydrogen atom n=5 n=4 - + n=3 n=2 13.6 = [ev]
More informationSingle Photon detectors
Single Photon detectors Outline Motivation for single photon detection Semiconductor; general knowledge and important background Photon detectors: internal and external photoeffect Properties of semiconductor
More informationSemiconductor Disk Laser on Microchannel Cooler
Semiconductor Disk Laser on Microchannel Cooler Eckart Gerster An optically pumped semiconductor disk laser with a double-band Bragg reflector mirror is presented. This mirror not only reflects the laser
More informationUltrafast X-Ray-Matter Interaction and Damage of Inorganic Solids October 10, 2008
Ultrafast X-Ray-Matter Interaction and Damage of Inorganic Solids October 10, 2008 Richard London rlondon@llnl.gov Workshop on Interaction of Free Electron Laser Radiation with Matter Hamburg This work
More informationChapter 1 INTRODUCTION AND BASIC CONCEPTS
Heat and Mass Transfer: Fundamentals & Applications 5th Edition in SI Units Yunus A. Çengel, Afshin J. Ghajar McGraw-Hill, 2015 Chapter 1 INTRODUCTION AND BASIC CONCEPTS Mehmet Kanoglu University of Gaziantep
More informationResonator Fabrication for Cavity Enhanced, Tunable Si/Ge Quantum Cascade Detectors
Resonator Fabrication for Cavity Enhanced, Tunable Si/Ge Quantum Cascade Detectors M. Grydlik 1, P. Rauter 1, T. Fromherz 1, G. Bauer 1, L. Diehl 2, C. Falub 2, G. Dehlinger 2, H. Sigg 2, D. Grützmacher
More informationPRESENTED BY: PROF. S. Y. MENSAH F.A.A.S; F.G.A.A.S UNIVERSITY OF CAPE COAST, GHANA.
SOLAR CELL AND ITS APPLICATION PRESENTED BY: PROF. S. Y. MENSAH F.A.A.S; F.G.A.A.S UNIVERSITY OF CAPE COAST, GHANA. OUTLINE OF THE PRESENTATION Objective of the work. A brief introduction to Solar Cell
More informationBETTER DESIGN AND NEW TECHNOLOGIES IMPROVE LASER POWER MEASUREMENT INSTRUMENTATION
BETTER DESIGN AND NEW TECHNOLOGIES IMPROVE LASER POWER MEASUREMENT INSTRUMENTATION Luigi Argenti, Andrea Brinciotti, Flavio Ferretti - Laserpoint s.r.l.- Vimodrone Italy New challenges from High Brightness
More informationEffects of Chrome Pattern Characteristics on Image Placement due to the Thermomechanical Distortion of Optical Reticles During Exposure
Effects of Chrome Pattern Characteristics on Image Placement due to the Thermomechanical Distortion of Optical Reticles During Exposure A. Abdo, ab L. Capodieci, a I. Lalovic, a and R. Engelstad b a Advanced
More informationTemperature Dependent Optical Band Gap Measurements of III-V films by Low Temperature Photoluminescence Spectroscopy
Temperature Dependent Optical Band Gap Measurements of III-V films by Low Temperature Photoluminescence Spectroscopy Linda M. Casson, Francis Ndi and Eric Teboul HORIBA Scientific, 3880 Park Avenue, Edison,
More informationCoolant. Circuits Chip
1) A square isothermal chip is of width w=5 mm on a side and is mounted in a subtrate such that its side and back surfaces are well insulated, while the front surface is exposed to the flow of a coolant
More informationBlue-green Emitting Semiconductor Disk Lasers with Intra-Cavity Frequency Doubling
Blue-green Emitting Semiconductor Disk Lasers with Intra-Cavity Frequency Doubling Eckart Schiehlen and Michael Riedl Diode-pumped semiconductor disk lasers, also referred to as VECSEL (Vertical External
More informationρ ρ LED access resistances d A W d s n s p p p W the output window size p-layer d p series access resistance d n n-layer series access resistance
LED access resistances W the output window size p-layer series access resistance d p n-layer series access resistance d n The n-layer series access resistance R = ρ s n where the resistivity of the n-layer
More informationWhat are Lasers? Light Amplification by Stimulated Emission of Radiation LASER Light emitted at very narrow wavelength bands (monochromatic) Light
What are Lasers? What are Lasers? Light Amplification by Stimulated Emission of Radiation LASER Light emitted at very narrow wavelength bands (monochromatic) Light emitted in a directed beam Light is coherenent
More informationHigh Power Diode Lasers
Lecture 10/1 High Power Diode Lasers Low Power Lasers (below tenth of mw) - Laser as a telecom transmitter; - Laser as a spectroscopic sensor; - Laser as a medical diagnostic tool; - Laser as a write-read
More informationMyoung-Soo Kim, Min-Ki Kim, Sung-Eun Jo, Chulmin Joo, and Yong-Jun Kim*
Supplementary information Refraction-Assisted Solar Thermoelectric Generator based on Phase-Change lens Myoung-Soo Kim, Min-Ki Kim, Sung-Eun Jo, Chulmin Joo, and Yong-Jun Kim* Department of Mechanical
More informationPossibilities of Using COMSOL Software in Physics
ALEKSANDRAS STULGINSKIS UNIVERSITY Possibilities of Using COMSOL Software in Physics Jolita Sakaliūnienė 1 Overview Requirement of study quality Student motivation COMSOL software Composition of COMSOL
More informationLuminescence Process
Luminescence Process The absorption and the emission are related to each other and they are described by two terms which are complex conjugate of each other in the interaction Hamiltonian (H er ). In an
More informationNEW TECHNIQUES DEDICATED TO THE CHARACTERIZATION OF INNOVATIVE FUELS
ARWIF 2005, Oak Ridge, February 16-18, 2005 NEW TECHNIQUES DEDICATED TO THE CHARACTERIZATION OF INNOVATIVE FUELS Virginie BASINI (1), François CHAROLLAIS (2), Denis ROCHAIS (3), Doriane HELARY (4), Marc
More informationA Multipass Optics for Quantum-Well-Pumped Semiconductor Disk Lasers
Multipass-Pumped Semiconductor Disk Lasers 37 A Multipass Optics for Quantum-Well-Pumped Semiconductor Disk Lasers Markus Polanik The pump absorption of quantum-well-pumped semiconductor disk lasers can
More informationIon Implantation. alternative to diffusion for the introduction of dopants essentially a physical process, rather than chemical advantages:
Ion Implantation alternative to diffusion for the introduction of dopants essentially a physical process, rather than chemical advantages: mass separation allows wide varies of dopants dose control: diffusion
More informationBroadband Quantum-Dot/Dash Lasers
Broadband Quantum-Dot/Dash Lasers Boon S. Ooi, Electrical & Computer Eng. Lehigh University Tel: 610-758 2606, email:bsooi@lehigh.edu ACKNOWDLEDGEMENT Students and Postdoc: Hery S. Djie, Yang Wang, Clara
More information2D Simulations and Electro-Thermal Analysis of Micro-Heater Designs Using COMSOL TM for Gas Sensor Applications
Presented at the COMSOL Conference 2010 India 2D Simulations and Electro-Thermal Analysis of Micro-Heater Designs Using COMSOL TM for Gas Sensor Applications Presented By Velmathi.G, Ramshanker.N and Mohan.S
More informationChapter 5. Semiconductor Laser
Chapter 5 Semiconductor Laser 5.0 Introduction Laser is an acronym for light amplification by stimulated emission of radiation. Albert Einstein in 1917 showed that the process of stimulated emission must
More informationMechanisms of Visible Photoluminescence from Size-Controlled Silicon Nanoparticles
Mat. Res. Soc. Symp. Proc. Vol. 737 23 Materials Research Society F1.5.1 Mechanisms of Visible Photoluminescence from Size-Controlled Silicon Nanoparticles Toshiharu Makino *, Nobuyasu Suzuki, Yuka Yamada,
More informationHeat Transfer: Physical Origins and Rate Equations. Chapter One Sections 1.1 and 1.2
Heat Transfer: Physical Origins and Rate Equations Chapter One Sections 1.1 and 1. Heat Transfer and Thermal Energy What is heat transfer? Heat transfer is thermal energy in transit due to a temperature
More informationValidation of DNS techniques for dynamic combined indoor air and constructions simulations using an experimental scale model
Excerpt from the Proceedings of the COMSOL Conference 2008 Hannover Validation of DNS techniques for dynamic combined indoor air and constructions simulations using an experimental scale model T.A.J. (Dennis)
More informationFabrication Technology, Part I
EEL5225: Principles of MEMS Transducers (Fall 2004) Fabrication Technology, Part I Agenda: Microfabrication Overview Basic semiconductor devices Materials Key processes Oxidation Thin-film Deposition Reading:
More informationDiode Lasers and Photonic Integrated Circuits
Diode Lasers and Photonic Integrated Circuits L. A. COLDREN S. W. CORZINE University of California Santa Barbara, California A WILEY-INTERSCIENCE PUBLICATION JOHN WILEY & SONS, INC. NEW YORK / CHICHESTER
More informationLuminescence basics. Slide # 1
Luminescence basics Types of luminescence Cathodoluminescence: Luminescence due to recombination of EHPs created by energetic electrons. Example: CL mapping system Photoluminescence: Luminescence due to
More informationOPTI510R: Photonics. Khanh Kieu College of Optical Sciences, University of Arizona Meinel building R.626
OPTI510R: Photonics Khanh Kieu College of Optical Sciences, University of Arizona kkieu@optics.arizona.edu Meinel building R.626 Announcements Homework #6 is assigned, due May 1 st Final exam May 8, 10:30-12:30pm
More informationEffect of non-uniform distribution of electric field on diffusedquantum well lasers
Title Effect of non-uniform distribution of electric field on diffusedquantum well lasers Author(s) Man, WM; Yu, SF Citation IEEE Hong Kong Electron Devices Meeting Proceedings, Hong Kong, China, 29 August
More informationNanocomposite photonic crystal devices
Nanocomposite photonic crystal devices Xiaoyong Hu, Cuicui Lu, Yulan Fu, Yu Zhu, Yingbo Zhang, Hong Yang, Qihuang Gong Department of Physics, Peking University, Beijing, P. R. China Contents Motivation
More informationLaser Types Two main types depending on time operation Continuous Wave (CW) Pulsed operation Pulsed is easier, CW more useful
Main Requirements of the Laser Optical Resonator Cavity Laser Gain Medium of 2, 3 or 4 level types in the Cavity Sufficient means of Excitation (called pumping) eg. light, current, chemical reaction Population
More informationSignal regeneration - optical amplifiers
Signal regeneration - optical amplifiers In any atom or solid, the state of the electrons can change by: 1) Stimulated absorption - in the presence of a light wave, a photon is absorbed, the electron is
More informationLaser processing of materials. Temperature distributions
Laser processing of materials Temperature distributions Prof. Dr. Frank Mücklich Dr. Andrés Lasagni Lehrstuhl für Funktionswerkstoffe Sommersemester 7 Contents: Temperature distributions 1. Definitions.
More informationFabrication of Efficient Blue Light-Emitting Diodes with InGaN/GaN Triangular Multiple Quantum Wells. Abstract
Fabrication of Efficient Blue Light-Emitting Diodes with InGaN/GaN Triangular Multiple Quantum Wells R. J. Choi, H. W. Shim 2, E. K. Suh 2, H. J. Lee 2, and Y. B. Hahn,2, *. School of Chemical Engineering
More informationLEC E T C U T R U E R E 17 -Photodetectors
LECTURE 17 -Photodetectors Topics to be covered Photodetectors PIN photodiode Avalanche Photodiode Photodetectors Principle of the p-n junction Photodiode A generic photodiode. Photodetectors Principle
More informationIon Implantation ECE723
Ion Implantation Topic covered: Process and Advantages of Ion Implantation Ion Distribution and Removal of Lattice Damage Simulation of Ion Implantation Range of Implanted Ions Ion Implantation is the
More informationSTUDY OF HEAT TRANSFER MECHANISMS DURING THE LENS TM PROCESS
STUDY OF HEAT TRANSFER MECHANISMS DURING THE LENS TM PROCESS Liang Wang 1 and Sergio Felicelli 1. Center for Advanced Vehicular Systems, Mississippi State University, Mississippi State, MS 3976, USA; email:
More informationContinuous room-temperature operation of optically pumped InGaAs/InGaAsP microdisk lasers
Continuous room-temperature operation of optically pumped InGaAs/InGaAsP microdisk lasers S. M. K. Thiyagarajan, A. F. J. Levi, C. K. Lin, I. Kim, P. D. Dapkus, and S. J. Pearton + Department of Electrical
More informationSupplementary Information Our InGaN/GaN multiple quantum wells (MQWs) based one-dimensional (1D) grating structures
Polarized white light from hybrid organic/iii-nitrides grating structures M. Athanasiou, R. M. Smith, S. Ghataora and T. Wang* Department of Electronic and Electrical Engineering, University of Sheffield,
More informationUNIT 3. By: Ajay Kumar Gautam Asst. Prof. Dev Bhoomi Institute of Technology & Engineering, Dehradun
UNIT 3 By: Ajay Kumar Gautam Asst. Prof. Dev Bhoomi Institute of Technology & Engineering, Dehradun 1 Syllabus Lithography: photolithography and pattern transfer, Optical and non optical lithography, electron,
More informationSUPPLEMENTARY MATERIALS FOR PHONON TRANSMISSION COEFFICIENTS AT SOLID INTERFACES
148 A p p e n d i x D SUPPLEMENTARY MATERIALS FOR PHONON TRANSMISSION COEFFICIENTS AT SOLID INTERFACES D.1 Overview The supplementary information contains additional information on our computational approach
More informationQuantum Dots for Advanced Research and Devices
Quantum Dots for Advanced Research and Devices spectral region from 450 to 630 nm Zero-D Perovskite Emit light at 520 nm ABOUT QUANTUM SOLUTIONS QUANTUM SOLUTIONS company is an expert in the synthesis
More informationESE370: Circuit-Level Modeling, Design, and Optimization for Digital Systems
ESE370: Circuit-Level Modeling, Design, and Optimization for Digital Systems Lec 6: September 18, 2017 MOS Model You are Here: Transistor Edition! Previously: simple models (0 and 1 st order) " Comfortable
More informationSpecial Topics: Photonics and Laser Applications in Engineering ENSC (Undergraduate) (3-0-2) (Graduate) (3-0-0)
Special Topics: Photonics and Laser Applications in Engineering ENSC 460-4 (Undergraduate) (3-0-2) 894-3 (Graduate) (3-0-0) Glenn Chapman, Rm 8831; email glennc@cs.sfu.ca Professor Schedule For 2003-3
More informationThermal Sensors and Actuators
Thermal Sensors and Actuators Part I Fundamentals of heat transfer Heat transfer occurs where there is a temperature gradient until an equilibrium is reached. Four major mechanism Thermal conduction Natural
More informationASSUMPTIONS: (1) One-dimensional, radial conduction, (2) Constant properties.
PROBLEM 5.5 KNOWN: Diameter and radial temperature of AISI 00 carbon steel shaft. Convection coefficient and temperature of furnace gases. FIND: me required for shaft centerline to reach a prescribed temperature.
More informationPHOTOVOLTAICS Fundamentals
PHOTOVOLTAICS Fundamentals PV FUNDAMENTALS Semiconductor basics pn junction Solar cell operation Design of silicon solar cell SEMICONDUCTOR BASICS Allowed energy bands Valence and conduction band Fermi
More informationNUMERICAL SIMULATION OF PULSE LASER ABLATION 1
NUMERICAL SIMULATION OF PULSE LASER ABLATION 1 Pritamkumar Dake Mechanical engineering department SRES College of engineering Kopargaon, Maharastra, India Email: 1 Pritam.dake@gmail.com Abstract Pulsed
More informationSupplementary Figure S1. AFM images of GraNRs grown with standard growth process. Each of these pictures show GraNRs prepared independently,
Supplementary Figure S1. AFM images of GraNRs grown with standard growth process. Each of these pictures show GraNRs prepared independently, suggesting that the results is reproducible. Supplementary Figure
More informationA RIDGE WAVEGUIDE FOR THERMO-OPTIC APPLICATION
Progress In Electromagnetics Research Letters, Vol. 6, 1 9, 2009 A RIDGE WAVEGUIDE FOR THERMO-OPTIC APPLICATION A. M. Al-Hetar, A. S. M. Supa at, and A. B. Mohammad Photonics Technology Center (PTC) Faculty
More informationReview of Optical Properties of Materials
Review of Optical Properties of Materials Review of optics Absorption in semiconductors: qualitative discussion Derivation of Optical Absorption Coefficient in Direct Semiconductors Photons When dealing
More informationUNCORRECTED PROOF. Author Proof
Chapter No.: 16 Date: 13-2-2015 Time: 3:48 pm Page: 1/8 1 Chapter 16 2 I V Characterization of the Irradiated 3 ZnO:Al Thin Film on P-Si Wafers By 4 Reactor Neutrons 5 Emrah Gunaydın, Utku Canci Matur,
More informationSUPPLEMENTARY INFORMATION
doi:10.1038/nature12036 We provide in the following additional experimental data and details on our demonstration of an electrically pumped exciton-polariton laser by supplementing optical and electrical
More informationComputational Modeling of a Solar Thermoelectric Generator
Computational Modeling of a Solar Thermoelectric Generator Undergraduate Thesis Presented in Partial Fulfillment of the Requirements for Graduation with Research Distinction at The Ohio State University
More informationFree-Space MEMS Tunable Optical Filter in (110) Silicon
Free-Space MEMS Tunable Optical Filter in (110) Silicon Ariel Lipson & Eric M. Yeatman Optical & Semiconductor Group Outline Device - Optical Filter Optical analysis Fabrication Schematic Fabricated 2
More informationCathodolumiescence Studies of the Density of States of Disordered Silicon Dioxide
Utah State University DigitalCommons@USU Presentations Materials Physics Fall 2014 Cathodolumiescence Studies of the Density of States of Disordered Silicon Dioxide JR Dennison Utah State Univesity Amberly
More informationLaser Diodes. Revised: 3/14/14 14: , Henry Zmuda Set 6a Laser Diodes 1
Laser Diodes Revised: 3/14/14 14:03 2014, Henry Zmuda Set 6a Laser Diodes 1 Semiconductor Lasers The simplest laser of all. 2014, Henry Zmuda Set 6a Laser Diodes 2 Semiconductor Lasers 1. Homojunction
More informationIndustrial Applications of Ultrafast Lasers: From Photomask Repair to Device Physics
Industrial Applications of Ultrafast Lasers: From Photomask Repair to Device Physics Richard Haight IBM TJ Watson Research Center PO Box 218 Yorktown Hts., NY 10598 Collaborators Al Wagner Pete Longo Daeyoung
More informationSemiconductor Quantum Dot Nanostructures and their Roles in the Future of Photonics
550 Brazilian Journal of Physics, vol. 34, no. 2B, June, 2004 Semiconductor Quantum Dot Nanostructures and their Roles in the Future of Photonics S. Fafard, K. Hinzer, and C. N. Allen Institute for Microstructural
More informationChapter-4 Stimulated emission devices LASERS
Semiconductor Laser Diodes Chapter-4 Stimulated emission devices LASERS The Road Ahead Lasers Basic Principles Applications Gas Lasers Semiconductor Lasers Semiconductor Lasers in Optical Networks Improvement
More informationDevelopment of Contactless Method of the DUT Heating during Single-Event Effect Tests
Journal of Physical Science and Application 8 (2) (2018) 22-27 doi: 10.17265/2159-5348/2018.02.004 D DAVID PUBLISHING Development of Contactless Method of the DUT Heating during Single-Event Effect Tests
More informationProgress Report on Chamber Dynamics and Clearing
Progress Report on Chamber Dynamics and Clearing Farrokh Najmabadi, Rene Raffray, Mark S. Tillack, John Pulsifer, Zoran Dragovlovic (UCSD) Ahmed Hassanein (ANL) Laser-IFE Program Workshop May31-June 1,
More informationEnhanced performance of microbolometer. using coupled feed horn antenna
Enhanced performance of microbolometer using coupled feed horn antenna Kuntae Kim*,a, Jong-Yeon Park*, Ho-Kwan Kang*, Jong-oh Park*, Sung Moon*, Jung-ho Park a * Korea Institute of Science and Technology,
More informationCOST MP0601 Short Wavelength Laboratory Sources
Background: Short wavelength radiation has been used in medicine and materials studies since immediately after the 1895 discovery of X-rays. The development of synchrotron sources over the last ~25 years
More informationCd(Zn)Te semiconductor-based diodes for detection of X- and gamma-ray photons with high energy resolution and imaging formation
P-46 Cd(Zn)Te semiconductor-based diodes for detection of X- and gamma-ray photons with high energy resolution and imaging formation [1] Organization Project Leader: Volodymyr Gnatyuk, Ph.D., Assoc. Prof.,
More informationLight Interaction with Small Structures
Light Interaction with Small Structures Molecules Light scattering due to harmonically driven dipole oscillator Nanoparticles Insulators Rayleigh Scattering (blue sky) Semiconductors...Resonance absorption
More informationEE 6313 Homework Assignments
EE 6313 Homework Assignments 1. Homework I: Chapter 1: 1.2, 1.5, 1.7, 1.10, 1.12 [Lattice constant only] (Due Sept. 1, 2009). 2. Homework II: Chapter 1, 2: 1.17, 2.1 (a, c) (k = π/a at zone edge), 2.3
More informationIntroduction to Nonlinear Optics
Introduction to Nonlinear Optics Prof. Cleber R. Mendonca http://www.fotonica.ifsc.usp.br Outline Linear optics Introduction to nonlinear optics Second order nonlinearities Third order nonlinearities Two-photon
More informationPhoto Diode Interaction of Light & Atomic Systems Assume Only two possible states of energy: W u and W l Energy levels are infinitesimally sharp Optical transitions occur between u and l Monochromatic
More informationNanophysics: Main trends
Nano-opto-electronics Nanophysics: Main trends Nanomechanics Main issues Light interaction with small structures Molecules Nanoparticles (semiconductor and metallic) Microparticles Photonic crystals Nanoplasmonics
More informationOptoelectronics ELEC-E3210
Optoelectronics ELEC-E3210 Lecture 3 Spring 2017 Semiconductor lasers I Outline 1 Introduction 2 The Fabry-Pérot laser 3 Transparency and threshold current 4 Heterostructure laser 5 Power output and linewidth
More informationESH Benign Processes for he Integration of Quantum Dots (QDs)
ESH Benign Processes for he Integration of Quantum Dots (QDs) PIs: Karen K. Gleason, Department of Chemical Engineering, MIT Graduate Students: Chia-Hua Lee: PhD Candidate, Department of Material Science
More informationAutumn 2005 THERMODYNAMICS. Time: 3 Hours
CORK INSTITUTE OF TECHNOOGY Bachelor of Engineering (Honours) in Mechanical Engineering Stage 3 (Bachelor of Engineering in Mechanical Engineering Stage 3) (NFQ evel 8) Autumn 2005 THERMODYNAMICS Time:
More informationUNIVERSITY OF CALIFORNIA College of Engineering Department of Electrical Engineering and Computer Sciences. Professor Chenming Hu.
UNIVERSITY OF CALIFORNIA College of Engineering Department of Electrical Engineering and Computer Sciences EECS 130 Spring 2009 Professor Chenming Hu Midterm I Name: Closed book. One sheet of notes is
More informationTitle of file for HTML: Supplementary Information Description: Supplementary Figures and Supplementary References
Title of file for HTML: Supplementary Information Description: Supplementary Figures and Supplementary References Supplementary Figure 1. SEM images of perovskite single-crystal patterned thin film with
More informationSchool of Electrical and Computer Engineering, Cornell University. ECE 5330: Semiconductor Optoelectronics. Fall Due on Nov 20, 2014 by 5:00 PM
School of Electrical and Computer Engineering, Cornell University ECE 533: Semiconductor Optoelectronics Fall 14 Homewor 8 Due on Nov, 14 by 5: PM This is a long -wee homewor (start early). It will count
More informationUnit IV Semiconductors Engineering Physics
Introduction A semiconductor is a material that has a resistivity lies between that of a conductor and an insulator. The conductivity of a semiconductor material can be varied under an external electrical
More informationPhotovoltaic cell and module physics and technology. Vitezslav Benda, Prof Czech Technical University in Prague
Photovoltaic cell and module physics and technology Vitezslav Benda, Prof Czech Technical University in Prague benda@fel.cvut.cz www.fel.cvut.cz 1 Outlines Photovoltaic Effect Photovoltaic cell structure
More information1300nm-Range GaInNAs-Based Quantum Well Lasers with High Characteristic Temperature
3nm-Range GaInNAs-Based Quantum Well Lasers with High Characteristic Temperature by Hitoshi Shimizu *, Kouji Kumada *, Seiji Uchiyama * and Akihiko Kasukawa * Long wavelength- SQW lasers that include a
More informationME 476 Solar Energy UNIT TWO THERMAL RADIATION
ME 476 Solar Energy UNIT TWO THERMAL RADIATION Unit Outline 2 Electromagnetic radiation Thermal radiation Blackbody radiation Radiation emitted from a real surface Irradiance Kirchhoff s Law Diffuse and
More informationExamination Heat Transfer
Examination Heat Transfer code: 4B680 date: 17 january 2006 time: 14.00-17.00 hours NOTE: There are 4 questions in total. The first one consists of independent sub-questions. If necessary, guide numbers
More information