RoHS compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn solder. Halogen-free.

Transcription

1 KEMET Organic Capacitor (KO-CAP ) Automotive Grade T59, T598 & T599 High Humidity & High Temperature Automotive Grade Polymer Electrolytic, VDC Overview The KEMET Organic Capacitor (KO-CAP) is a solid electrolytic capacitor with a conductive polymer cathode, capable of delivering very low ESR and an improved capacitance retention at high frequencies. KO-CAP combines the low ESR of the multilayer ceramic, the high capacitance of aluminum electrolytic and the volumetric efficiency of tantalum into a single surface mount package. Unlike liquid electrolyte-based capacitors, KO-CAP has a very long operational life and high ripple current capabilities. The T59/T598/T599 High Humidity and High Temperature Polymer Electrolytic capacitors deliver higher capacitance and ESR stability under harsh environmental conditions. Enhancements to the design and selected material upgrades were introduced to deliver 500 hours (T59) or,000 hours (T598, T599) at 85 C/85% RH rated voltage and to fully comply with the AEC-Q200 qualification testing with maximum operational temperature life up to 25 C and 50 C respectively. These capacitors are manufactured in an ISO TS 6949 certified plant and are subjected to PPAP/PSW, as well as change control. Benefits Ultra low ESR Full compliance with AEC Q200 qualification test plan (T C, T C) Qualification plan based on AEC Q200 with 85 C/85% RH load specification limited to 500 hours (T59) TS 6949 certified plant Subject to PPAP/PSW and change control Meets or exceeds EIA standard 535BAAC Taped and reeled per EIA 48 Halogen-free, epoxy and RoHS compliant Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Applications Typical applications include decoupling and filtering in a variety of market segments, with special emphasis in automotive applications such as infotainment, ADAS, chassis and safety, as well as powertrain, where harsh conditions, such as high humidity and temperature, are a concern. Environmental Compliance RoHS compliant (6/6) according to Directive 2002/95/EC when ordered with 00% Sn solder. Halogen-free. One world. One KEMET KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208

2 K-SIM For a detailed analysis of specific part numbers, please visit ksim.kemet.com to access KEMET s K-SIM software. KEMET K-SIM is designed to simulate behavior of components with respect to frequency, ambient temperature, and DC bias levels. Ordering Information T 59X D 07 M 00 A T E025 Capacitor Class Series Case Size T = Tantalum 59 = 500 Hours load humidity 598 = AEC-Q200 qualified (25 C) 599 = AEC-Q200 qualified (50 C) B D V X Capacitance Code (pf) First two digits represent significant figures. Third digit specifies number of zeros. Capacitance Tolerance Rated Voltage (VDC) M = ±20% 2R5 = = = 0 06 = = = = = 50 Failure Rate/ Design Termination Finish ESR A = N/A T = 00% Tin (Sn) ESR in mω, 025 = 25 mω Performance Characteristics Item Operating Temperature Rated Capacitance Range 55 C to 05 C/25 C/50 C µf at 20 Hz/25 C Performance Characteristics Capacitance Tolerance M Tolerance (20%) Rated Voltage Range DF (20 Hz) ESR (00 khz) Leakage Current V Refer to Part Number Electrical Specification Table Refer to Part Number Electrical Specification Table 0. CV (µa) at rated voltage after 5 minutes KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 2

3 Qualification Test Condition Characteristics Endurance Storage Life Humidity Moisture Resistance* Temperature Cycling Surge Voltage Temperature Stability Mechanical Shock/ Vibration 05 C at rated voltage, 2,000 hours 25 C at 2/3 rated voltage, 2,000 hours (for 6V parts)** 25 C at 2/3 rated voltage,,000 hours (for > 6V parts)** 50 C at 2/3 rated voltage,,000 hours (T599) 05 C at 0 volts, 2,000 hours 25 C at 0 volts,,000 hours** 50 C at 0 volts,,000 hours (T599) 85 C, 85% RH, load, 500 hours (T59) 85 C, 85% RH, load,,000 hours (T598, T599) MIL STD 202, Method 06, 65 C, 90 00% RH, no load, 0 cycles JESD22, Test Method A04, 55 C to +05 C/+25 C/+50 C**,,000 cycles 05 C,.32 x rated voltage,,000 cycles, 33 Ω in series 25 C/50 C,.32 x (0.67 x V R ),,000 cycles, 33 Ω in series** Extreme temperature exposure at a succession of continuous steps at +25 C, 55 C, +25 C, +85 C, +05 C/+25 C/+50 C**, +25 C AEC Q200 (MIL STD 202, Method 23, Figure, Condition F.) AEC Q200 (MIL STD 202, Method 204, 5 g for 20 minutes/2 cycles each of 3 orientations. Test from 0 2, 000 Hz.) * T598 only ** Refer to part number specifications for individual temperature classification *** IL = Initial limit Δ C/C DF DCL Within 20%/+0% of initial value Within 2 x initial limit Within 2 x initial limit ESR Within 2 x initial limit Δ C/C Within 20%/+0% of initial value DF Within 2 x initial limit DCL Within 2 x initial limit ESR Within 2 x initial limit Δ C/C Within 5%/+35% of initial value DF Within.5 x initial limits DCL Within initial limit ESR Within 2 x initial limit Δ C/C Within 0%/+20% of initial value DF Within initial limit DCL Within initial limit ESR Within 2 x initial limit Δ C/C Within 20%/+0% of initial value DF Within initial limits DCL Within initial limit ESR Within 2 x initial limits Δ C/C Within 20%/+0% of initial value DF Within initial limits DCL Within initial limits ESR Within initial limits +25 C 55 C +85 C +05 C/+25 C/+50 C** Δ C/C IL*** ±20% ±20% ±30% DF IL IL.2 x IL.5 x IL DCL IL N/A 0 x IL 0 x IL Δ C/C Within ±0% of initial value DF Within initial limits ESR DCL Within initial limits Within initial limits KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 3

4 Reliability KO-CAP capacitors have an average failure rate of 0.5 %/,000 hours at category voltage, U C, and category temperature, T C. These capacitors are qualified using industry test standards at U C and T C. The minimum test time (,000 hours or 2,000 hours) is dependent on the product. The actual life expectancy of KO-CAP capacitors increases when application voltage, U A, and application temperature, T A, are lower than U C and T C. As a general guideline, when U A < 0.9 * U C and T A < 85 C, the life expectancy will typically exceed the useful lifetime of most hardware (> 0 years). The lifetime of a KO-CAP capacitor at a specific application voltage and temperature can be modeled using the equations below. A failure is defined as passing enough current to blow a -amp fuse. The calculation is an estimation based on empirical results and is not a guarantee. U VAF = ( C ) where: VAF = acceleration factor due to voltage, unitless U C = category voltage, volt U A = application voltage, volt n = exponent, 6 U A n [ E a ( )] k TAF = e 273+T 273+T A C where: TAF = acceleration factor due to temperature, unitless E a = activation energy,.4 ev k = Boltzmann s constant, 8.67E-5 ev/k T A = application temperature, C T C = category temperature, C AF = VAF * TAF where: AF = acceleration factor, unitless TAF = accerlation factor due to temperature, unitless VAF = acceleration factor due to voltage, unitless Life UA,T A = Life UC,T C * AF where: Life UA, TA = guaranteed life application voltage and temperature, years Life UC, TC = guaranteed life category voltage and temperature, years AF = acceleration factor, unitless 85 C (T R )/ 85 C (T C ) 05 C (T R )/ 05 C (T C ) 05 C (T R )/ 25 C (T C ) 05 C (T R )/ 50 C (T C ) Reliability Table Common Temperature Range Classifications Rated voltage (U R ) Category voltage (U C ) Rated voltage (U R ) Category voltage (U C ) Rated voltage (U R ) Category voltage (U C ) Rated voltage (U R ) Category voltage (U C ) Terms: Category voltage, U C : recommended peak DC operating voltage for continuous operation at the category temperature, T C. Rated voltage, U R : recommended peak DC operating voltage for continuous operation up to the rated temperature, T R. Category temperature, T C : recommended operating temperature. Voltage derating may be required at T C. Rated temperature, T R : recommended operating temperature without voltage derating. T R is equal to or lower than T C. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 4

5 Certification KEMET's internal qualification plan for this polymer electrolytic series of capacitors follows AEC-Q200 guidelines. For T59 the humidity bias is limited to a maximum of 500 hours. For T598 the qualification plan is fully compliant with AEC-Q200 with maximum operational temperature of 25 C. For T599 the qualification plan is fully compliant with AEC-Q200 with maximum operational temperature of 50 C. Electrical Characteristics ESR vs. Frequency T59 Capacitance vs. Frequency T59 Impedance, ESR (Ohms), B476M00_IMP 59B476M00_ESR 59D07M00_IMP 59D07M00_ESR 59D476M06_IMP 59D476M06_ESR 59V227M2R5_IMP 59V227M2R5_ESR 59D06M050_IMP 59D06M050_ESR Capacitance (µf), B476M00_Cap (µf) 59D07M00_Cap (µf) 59D06M050_Cap (µf) 59D476M06_Cap (µf) ,000 0,000 00,000,000,000 0,000,000 Frequency (Hz) 59V227M2R5_Cap (µf) 00,000 0,000 00,000,000,000 0,000,000 Frequency (Hz) 00 ESR vs. Frequency T598,000 Capacitance vs. Frequency T B476M00_IMP 598B476M00_ESR Impedance, ESR (Ohms) D07M00_IMP 598D07M00_ESR 598D227M00_IMP 598D227M00_ESR 598D07M06_IMP 598D07M06_ESR Capacitance (µf) ,000 0,000 00,000,000,000 0,000,000 Frequency (Hz) 598B476M00_Cap (µf) 598D07M00_Cap (µf) 598D227M00_Cap (µf) 598D07M06_Cap (µf) 00,000 0,000 00,000,000,000 0,000,000 Frequency (Hz) KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 5

6 Electrical Characteristics (cont.) ESR vs. Frequency T599 Capacitance vs. Frequency T T599X336M035_IMP T599X336M035_ESR T599X336M035_CAP Impedance & ESR (0hms) 0 0. Capacitance (µf) ,000 0,000 00,000 Frequency (Hz),000,000 0,000, ,000 0,000 00,000 Frequency (Hz),000,000 0,000,000 Dimensions Millimeters (Inches) Metric will govern CATHODE (-) END VIEW W H X T S SIDE VIEW ANODE (+) END VIEW BOTTOM VIEW S B B Termination cutout at KEMET's option, either end R P A Glue pad shape/design at KEMET's option L F Case Size KEMET EIA L W H B ± ±0.2.9 ±0.2 (0.38 ±0.008) (0.0 ±0.008) (0.075 ±0.008) D ± ± ±0.3 (0.287 ±0.02) (0.69 ±0.02) (0.0 ±0.02) V ± ±0.3.9 ±0. (0.287 ±0.02) (0.69 ±0.02) (0.075 ±0.004) X ± ± ±0.3 (0.287 ±0.02) (0.69 ±0.02) (0.57±0.02) F ±0. ±(0.004) 2.2 (0.087) 2.4 (0.094) 2.4 (0.094) 2.4 (0.094) Component Dimensions S ±0.3 ±(0.02) 0.8 (0.03).3 (0.05).3 (0.05).3 (0.05) B ±0.5 (Ref) ± (0.06) 0.5 (0.020) N/A 0.5 (0.020) X (Ref) 0.0 ±0.0 (0.004 ±0.004) 0.0 ±0.0 (0.004 ±0.004) 0.05 (0.002) 0.0 ±0.0 (0.004 ±0.004) P (Ref) 0.5 (0.020) 0.9 (0.035) N/A R (Ref).0 (0.039).0 (0.039) 0.3 (0.005) 0.3 (0.005) T (Ref) 0.3 (0.005) 0.3 (0.005) 3.8 (0.50) 3.6 (0.42) A (Minimum). (0.043) 3.8 (0.50) 3.8 (0.50) 3.8 (0.50) Total Weight Notes: Reference (Ref) Dimensions provided for reference only. For low profile cases, no dimensions are provided for B, P or R, because these cases do not have a bevel or a notch. These weights are provided as reference. If exact weights are needed, please contact your KEMET sales representative..7 (0.067) (mg) KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 6

7 Table Ratings & Part Number Reference Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number DC Leakage DF ESR Allowable Ripple Current MSL Operating Temp AEC-Q200 Qualified VDC at 05 C µf KEMET/EIA µa at +25 C Max/5 Minutes % at +25 C 20 Hz Max mω at +25 C 00 khz Max ma at +45 C 00 khz Reflow Temp 260 C B/ T598B07M2R5ATE B/ T59B07M2R5ATE B/ T598B07M2R5ATE B/ T59B07M2R5ATE B/ T59B227M2R5ATE V/ T59V227M2R5ATE V/ T59V227M2R5ATE V/ T59V227M2R5ATE V/ T59V337M2R5ATE V/ T59V337M2R5ATE D/ T59D337M2R5ATE D/ T59D337M2R5ATE B/ T598B07M004ATE B/ T59B07M004ATE V/ T59V227M004ATE V/ T59V227M004ATE B/ T598B336M006ATE B/ T59B336M006ATE B/ T598B476M006ATE B/ T59B476M006ATE B/ T598B686M006ATE B/ T59B686M006ATE V/ T59V57M006ATE V/ T59V57M006ATE D/ T598D57M006ATE D/ T59D57M006ATE D/ T598D227M006ATE D/ T59D227M006ATE D/ T598D337M006ATE D/ T598D337M006ATE D/ T598D337M006ATE D/ T59D337M006ATE D/ T59D337M006ATE D/ T59D337M006ATE B/ T598B336M00ATE B/ T59B336M00ATE B/ T598B476M00ATE B/ T59B476M00ATE D/ T598D07M00ATE D/ T598D07M00ATE D/ T598D07M00ATE D/ T59D07M00ATE D/ T59D07M00ATE D/ T59D07M00ATE V/ T59V07M00ATE V/ T59V07M00ATE D/ T598D227M00ATE D/ T598D227M00ATE D/ T598D227M00ATE D/ T59D227M00ATE C T598/T599 Only VDC at 05 C µf KEMET/EIA µa at +25 C Max/5 Minutes % at +25 C 20 Hz Max mω at +25 C 00 khz Max ma at +45 C 00 khz Reflow Temp 260 C C T598/T599 Only Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number DC Leakage DF ESR Allowable Ripple Current MSL Operating Temp AEC Q200 Qualified T598 = AEC-Q200 qualified. T599 AEC-Q200 qualified 50 C and T59 = limited to 500 hours at 85 C/85% RH load. Refer to Ordering Information for additional detail. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 7

8 Table Ratings & Part Number Reference cont'd Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number DC Leakage DF ESR Allowable Ripple Current MSL Operating Temp AEC-Q200 Qualified VDC at 05 C µf KEMET/EIA µa at +25 C Max/5 Minutes % at +25 C 20 Hz Max mω at +25 C 00 khz Max ma at +45 C 00 khz Reflow Temp 260 C C T598/T599 Only D/ T59D227M00ATE D/ T59D227M00ATE D/ T59D476M06ATE D/ T598D07M06ATE D/ T59D07M06ATE D/ T598D57M06ATE D/ T59D57M06ATE D/ T59D476M020ATE D/ T59D686M020ATE D/ T59D686M020ATE D/ T59D226M025ATE D/ T598D336M025ATE D/ T59D336M025ATE D/ T598D476M025ATE B/ T598B475M035ATE B/ T59B475M035ATE D/ T598D06M035ATE D/ T59D06M035ATE V/ T598V06M035ATE V/ T59V06M035ATE D/ T598D226M035ATE D/ T598D336M035ATE D/ T59D336M035ATE X/ T598X336M035ATE X/ T599X336M035ATE X/ T59X476M035ATE D/ T59D06M050ATE VDC at 05 C µf KEMET/EIA µa at +25 C Max/5 Minutes % at +25 C 20 Hz Max mω at +25 C 00 khz Max ma at +45 C 00 khz Reflow Temp 260 C C T598/T599 Only Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number DC Leakage DF ESR Allowable Ripple Current MSL Operating Temp AEC Q200 Qualified T598 = AEC-Q200 qualified. T599 AEC-Q200 qualified 50 C and T59 = limited to 500 hours at 85 C/85% RH load. Refer to Ordering Information for additional detail. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 8

9 Derating Guidelines 25 C 50 C % Rated Voltage 00% 95% Rated Voltage 90% 85% Recommended Application Voltage V R 0 V 80% 75% Recommended Application Voltage 6 V 70% 65% 60% 55% 67% 60% 54% 50% Temperature ( C) % Rated Voltage 00% 95% Rated Voltage 90% 85% Recommended Application Voltage V R 0 V 80% 75% 70% Recommended Application Voltage 6 V 65% 60% 67% 60% 55% 54% 50% Temperature ( C) Recommended Application Voltage KO-CAPs are solid state capacitors that demonstrate no wearout mechanism when operated within their recommended guidelines. While the KO-CAP can be operated at full rated voltage, most circuit designers seek a minimum level of assurance in long term reliability, which should be demonstrated with data. A voltage derating can provide the desired level of demonstrated reliability based on industry accepted acceleration models. Since most applications do require long term reliability, KEMET recommends that designers consider a voltage derating, according the graph above, for the maximum steady state voltage. Voltage Rating Recommended Steady State Voltage 55 C to 05 C 05 C to 25 C (T598) 05 C to 50 C (T599) 2.5 V V R 0 V 90% of V R 60% of V R 60% of V R V R 6 V 80% of V R 54% of V R 54% of V R V R = Rated voltage KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 9

10 Ripple Current/Ripple Voltage Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation capabilities of the device. Permissible AC ripple voltage which may be applied is limited by two criteria:. The positive peak AC voltage plus the DC bias voltage, if any, must not exceed the DC voltage rating of the capacitor. 2. The negative peak AC voltage in combination with bias voltage, if any, must not exceed the allowable limits specified for reverse voltage. See the Reverse Voltage section for allowable limits. The maximum power dissipation by case size can be determined using the table at right. The maximum power dissipation rating stated in the table must be reduced with increasing environmental operating temperatures. Refer to the table below for temperature compensation requirements. Case Code EIA Case Code Power Dissipation (P max) mwatts at 45 C with +30 C Rise B D V X Using the P max of the device, the maximum allowable rms ripple current or voltage may be determined. I(max) = P max/r E(max) = Z P max/r I = rms ripple current (amperes) E = rms ripple voltage (volts) P max = maximum power dissipation (watts) R = ESR at specified frequency (ohms) Z = Impedance at specified frequency (ohms) Temperature Compensation Multipliers for Ripple Current T 45 C 45 C < T 85 C 85 C < T 05 C T 25 C T 50 C T = Environmental temperature The maximum power dissipation rating must be reduced with increasing environmental operating temperatures. Refer to the Temperature Compensation Multiplier table for details. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 0

11 Surge Voltage Surge voltage is the maximum voltage (peak value) which may be applied to the capacitor. The surge voltage must not be applied for periodic charging and discharging in course of normal operation and cannot be part of the application voltage. Surge voltage capability is demonstrated by application of,000 cycles at operating temperature. The parts are charged through a 33 Ohm resistor for 30 seconds and then discharged though a 33 Ohm resistor for each cycle. Rated Voltage (V) Surge Voltage (V) Derated Voltage (V) Derated Surge Voltage (V) Derated Voltage (V) Derated Surge Voltage (V) 55 C to 05 C Up to 25 C up to 50 C* *T599 Only Reverse Voltage Polymer electrolytic capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong polarity. These devices will withstand a small degree of transient voltage reversal for short periods as shown in the below table. Temperature Permissible Transient Reverse Voltage 25 C 5% of rated voltage 55 C 0% of rated voltage 85 C 5% of rated voltage 05 C 3% of rated voltage 25 C* 50 C** *For series rated to 25 C ** For series rated to 50 C % of rated voltage % of rated voltage KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208

12 Table 2 Land Dimensions/Courtyard KEMET Metric Size Code Density Level A: (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) Case EIA W L S V V2 W L S V V2 W L S V V2 B D V X¹ Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC standard 735 (IPC 735). Height of these chips may create problems in wave soldering. 2 Land pattern geometry is too small for silkscreen outline. V L L W W V2 S Grid Placement Courtyard KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 2

13 Soldering Process KEMET s families of surface mount capacitors are compatible with wave (single or dual), convection, IR, or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J STD 020D standard for moisture sensitivity testing. The devices can safely withstand a maximum of three reflow passes at these conditions. Please note that although the X/ case size can withstand wave soldering, the tall profile (4.3 mm maximum) dictates care in wave process development. Hand soldering should be performed with care due to the difficulty in process control. If performed, care should be taken to avoid contact of the soldering iron to the molded case. The iron should be used to heat the solder pad, applying solder between the pad and the termination, until reflow occurs. Once reflow occurs, the iron should be removed immediately. Wiping the edges of a chip and heating the top surface is not recommended. Profile Feature Preheat/Soak SnPb Assembly Pb-Free Assembly Temperature Minimum (T Smin ) 00 C 50 C Temperature (T Smax ) 50 C 200 C Time (t s ) from T smin to T smax ) seconds seconds Ramp-up Rate (T L to T P ) 3 C/second maximum 3 C/second maximum Liquidous Temperature (T L ) 83 C 27 C Time Above Liquidous (t L ) seconds seconds Peak Temperature (T P ) Time within 5 C of Peak Temperature (t P ) 220 C* 235 C** 250 C* 260 C** 20 seconds maximum 30 seconds maximum Ramp-down Rate (T P to T L ) 6 C/second maximum 6 C/second maximum Time 25 C to Peak Temperature 6 minutes maximum 8 minutes maximum Note: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. *Case Size D, E, P, Y, and X **Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z Temperature T P T L T smax T smin Ramp Up Rate = 3 C/second Ramp Down Rate = 6 C/second t s t L t P C to Peak Time Storage All KO-CAP capacitors are shipped in moisture barrier bags (MBBs) with desiccant and humidity indicator card (HIC). These parts are classified as moisture sensitivity level 3 (MSL3) per IPC/JEDEC J-STD-020 and packaged per IPC/JEDEC J STD 033, MSL3 specifies a floor time of 68 H at 30 C maximum temperature and 60% relative humidity. Unused capacitors should be sealed in a MBB with fresh desiccant. Calculated shelf life in sealed bag: 2 months from bag seal date in a storage environment of < 40 C and humidity < 90% RH 24 months from bag seal date in a storage environment of < 30 C and humidity < 70% RH If baking is required, refer to IPC/JEDEC J STD 033 for bake procedure. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 3

14 Construction Molded Epoxy Case Polarity Stripe (+) Polarity Bevel (+) Detailed Cross Section Silver Paint (Fourth Layer) Wire Leadframe ( Cathode) Wire Weld (to attach wire) Carbon (Third Layer) Silver Adhesive Molded Epoxy Case Leadframe (+ Anode) Polymer (Second Layer) Ta 2 O 5 Dielectric (First Layer) Tantalum Capacitor Marking Rated Voltage Polarity Indicator (+) Picofarad Code KEMET ID Date Code* Date Code * st digit = Last number of year 5 = = = = nd and 3 rd digit = Week of the year 0 = st week of the year to 52 = 52 nd week of the year * 822 = 22 nd week of 208 KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 4

15 Tape & Reel Packaging Information KEMET s molded chip capacitor families are packaged in 8 and 2 mm plastic tape on 7" and 3" reels in accordance with EIA Standard 48: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging system is compatible with all tape-fed automatic pick-and-place systems. Right hand orientation only Embossed carrier (+) ( ) Embossment Top tape thickness 0.0 mm (0.004 ) maximum thickness 8 mm (0.35 ) or 2 mm (0.472 ) 80 mm (7.0 ) or 330 mm (3. ) Table 3 Packaging Quantity Case Code Tape Width (mm) 7" Reel* 3" Reel* KEMET EIA S ,500 0,000 T ,000 0,000 M ,500 8,000 U ,000 5,000 L ,000 3,000 W ,000 3,000 Z ,000 3,000 V ,000 3,000 A ,000 9,000 B ,000 8,000 C ,000 D ,500 Q ,000 3,000 Y ,000 X ,000 E/T428P ,000 H ,000 2,500 O * No C-Spec required for 7" reel packaging. C-7280 required for 3" reel packaging. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 5

16 Figure Embossed (Plastic) Carrier Tape Dimensions T T 2 ØD 0 P 2 P 0 (0 pitches cumulative tolerance on tape ±0.2 mm) E A 0 F K 0 W B B 0 E 2 S P T Cover Tape B is for tape feeder reference only, including draft concentric about B 0. Center Lines of Cavity User Direction of Unreeling ØD Embossment For cavity size, see Note, Table 4 Table 4 Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions Millimeters (Inches) Tape Size D 0 D Minimum Note E P 0 P 2 R Reference Note 2 S Minimum Note 3 T T 8 mm 2 mm / 0.0 ( / 0.0).0 (0.039).5 (0.059).75 ±0.0 (0.069 ±0.004) 4.0 ±0.0 (0.57 ±0.004) 2.0 ±0.05 (0.079 ±0.002) 25.0 (0.984) 30 (.8) (0.024) (0.024) 0.00 (0.004) Tape Size Pitch 8 mm Single (4 mm) 2 mm Single (4 mm) and Double (8 mm) B Note (0.7) 8.2 (0.323) Variable Dimensions Millimeters (Inches) E 2 Minimum F P T 2 W A 0, B 0 & K (0.246) 0.25 (0.404) 3.5 ±0.05 (0.38 ±0.002) 5.5 ±0.05 (0.27 ±0.002) 2.0 ±0.05 or 4.0 ±0.0 (0.079 ±0.002 or 0.57 ±0.004) 2.0 ±0.05 (0.079 ±0.002) or 4.0 ±0.0 (0.57 ±0.004) or 8.0 ±0.0 (0.35 ±0.004) 2.5 (0.098) 4.6 (0.8) 8.3 (0.327) 2.3 (0.484). The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape, with or without components, shall pass around R without damage (see Figure 4). 3. If S <.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 48 D, paragraph 4.3, section b). 4. B dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A 0, B 0 and K 0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 2 mm tapes (see Figure 2). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 2 mm wide tape (see Figure 3). (e) see Addendum in EIA Standard 48 D for standards relating to more precise taping requirements. Note 5 KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 6

17 Packaging Information Performance Notes. Cover tape break force:.0 kg minimum. 2. Cover tape peel strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0. to.0 newton (0 to 00 gf) 2 mm 0. to.3 newton (0 to 30 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 65 to 80 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±0 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 2 Component Rotation Bo T Ao Component Rotation Top View Typical Pocket Centerline Tape Width (mm) Rotation ( T ) 8, 2 20 Typical Component Centerline s Component Rotation Side View Tape Width (mm) 8, 2 20 Rotation ( S) Figure 3 Lateral Movement Figure 4 Bending Radius 8 mm & 2 mm Tape 0.5 mm maximum 0.5 mm maximum Embossed Carrier Punched Carrier R Bending Radius R KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 7

18 Figure 5 Reel Dimensions Full Radius, See Note Access Hole at Slot Location (Ø 40 mm minimum) W 3 (Includes flange distortion at outer edge) W 2 (Measured at hub) A D (See Note) B (see Note) Note: Drive spokes optional; if used, dimensions B and D shall apply. C (Arbor hole diameter) If present, tape slot in core for tape start: 2.5 mm minimum width x 0.0 mm minimum depth W N (Measured at hub) Table 5 Reel Dimensions Metric will govern Constant Dimensions Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 2 mm 78 ±0.20 (7.008 ±0.008) or 330 ±0.20 (3.000 ±0.008).5 (0.059) Variable Dimensions Millimeters (Inches) / 0.2 ( / 0.008) 20.2 (0.795) Tape Size N Minimum W W 2 W 3 8 mm / ( / 0.0) (0.567) Shall accommodate tape 2 mm (.969) / width without interference ( / 0.0) (0.724) KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 8

19 Figure 6 Tape Leader & Trailer Dimensions Embossed Carrier Punched Carrier 8 mm & 2 mm only END Carrier Tape Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 60 mm minimum Top Cover Tape Components 00 mm minimum Leader 400 mm minimum Figure 7 Camber Elongated Sprocket Holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes mm maximum, either direction Straight Edge 250 mm KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 9

20 KEMET Electronics Corporation Sales Offices For a complete list of our global sales offi ces, please visit Disclaimer All product specifi cations, statements, information and data (collectively, the Information ) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation s ( KEMET ) knowledge of typical operating conditions for such applications, but are not intended to constitute and KEMET specifi cally disclaims any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC T2073_T59X 5/29/208 20