ISSN (ONLINE): , ISSN (PRINT):

Transcription

1 Volume-5, Issue-2, April-2015 International Journal of Engineering and Management Research Page Number: Vibration Effect of Different Number of Cracks, Length of Cracks, Cutting Teeth, Holes, Slits, Aspect Ratio, Thickness & Increase Slot End Hole Diameter on Circular TILE CUTTER by using ANSYS Hirave S.H. 1, Joshi M.M. 2, Gajjal S.Y. 3 1 P.G. Student, Department of Mechanical Design Engineering, NBN Sinhgad School of Engineering, Pune, INDIA 2 Asst. Prof. & HOD, Department of Mechanical Engineering, NBN Sinhgad School of Engineering, Pune, INDIA 3 Asst. Prof. & Head, PG Department of Mechanical Design Engineering, NBN Sinhgad School of Engineering, Pune, INDIA ABSTRACT Circular cutters with uniform radial cracks are extensively used in the cutting processes. Unwanted noise, vibration & accidental failure associated with the cutting process have become an important economic and technological problem in the industry. The knowledge of natural frequencies of components is of great interest in the study of response of structures to various excitations. Hence, it is important to study a circular tile cutter with central hole, which fixed at inner edge and free at outer edge with its dynamic response. In this study some efforts are taken for analyzing vibration characteristics of tile cutter used in tile cutting industries with free boundary condition but having different (enlargement of stress concentration holes, slot end hole diameter,numbers of cutting teeth s, aspect ratio, effect of number and length of cracks, variable radial slit, circular concentric slit, thickness).results From the FEA it is found that, this study is needful for design data preparation related to finding out natural frequency, mode shape, deformation & comparison vibration w.r.t different change in cutter. Thus Theoretical and ANSYS results obtained are to be compared. KEYWORDS - Circular tile Cutter, aspect ratio, teeth s, radial slit, circular concentric slit,different cracks, vibration,ansys. I. INTRODUCTION The study of the dynamic behavior of circular tile cutters with free boundary condition but having different (enlargement of stress concentration holes, slot end hole diameter,numbers of cutting teeth s, aspect ratio, effect of number and length of cracks, variable radial slit, circular concentric slit, thickness) is important, as used in several machine components, such as flywheels circular saw plates etc. The knowledge of natural frequencies of component is of great interest in the analysis of response of structures to various excitations. This study is fundamental for high-risk plants. Unwanted noise, vibration & accidental failure associated with the cutting process has become an important economic and technological problem in the industry that can be solved by this dissertation work. II. PHASES OF THE PAPER WORK The paper work has divided by different phases such as literature survey, theoretical investigation, analytical procedure and validation of results, Phase A -Review of literature regarding the work done. Extensive research review of the literature on this proposed topic vibration analysis of tile cutters implemented by different researchers at present and their comparison with the proposed conceptual method of analysis. Phase B -Theoretical investigation contain analysis of vibration characteristics of circular tile cutters with free boundary condition but having different ( numbers of cutting teeth, aspect ratio, effect of radial cracks, enlargement of stress concentration holes) is done with the some theoretical calculation by referring some formulae. Phase C- Analysis work is done by Using ANSYS 819 Copyright Vandana Publications. All Rights Reserved.

2 Analysis Procedure- C.1] Geometry Creation Geometry is created using CATIA V5 CAD Tool as shown in fig From bellow fig gives material property and their values wih unit.so select material data for spring steel tile cutter. C.2] Material Data C.3] Boundary Condition The material properties are assigned and boundary conditions are defined. Their all degrees of freedom on surface are taken. They are denoted with the blue flag Figure. This surface is fixed as shown in fig. Fig.II.C(3) Boundary Condition C.4] Mesh of Finite Elements Mesh on the beam is generated automatically by ANSYS, while is used the tetrahedral elements used with 1mm min element size 456 elements. 820 Copyright Vandana Publications. All Rights Reserved.

3 Fig.II.C(4) Meshing of plate C.5] Modal Analysis We can influence computational time of the analysis, when a range of frequencies or number of mode shapes is specified. The type of solver and the solution method in program ANSYS is selected automatically. For this modal analysis the direct solver method is used. The first six mode shapes are shown in Figure and the six natural frequencies are shown in cutter 2 images Fig.II.C (5.a) Deformed shape & Mode shape for frequency HZ. Phase D Validate the theoretical result with available software FEA (ANSYS) results Phase B-THEORETICAL ( ) 2 W. T. Norris and J. E. T. Pennyhave given values of βa for various ratios of inner radius to outer radius and different mode characteristics. First six harmonics are given in order for aspect ratio (b/a =0.1). ( βa) 2 Is non dimensional frequency parameter used to calculate natural frequencies of annular tile cutter. β a = a 3ρ( 1 υ ) ( ) ω Eh 2 Where, h = half thickness in mm E = Young s modulus N/m 2 ρ = Density of the tile cutter material in kg/m 3 ω = frequency in rad/s. υ = Poisson s ratio taken as 0.3 a = Outer radius of tile cutter in mm By putting all theoretical values as mentioned in test specimen w.r.t. different mode given bellow results are as tabulated follows. We will compare only aspect ratio and thickness these two parameter with theoretical and ANSYS results. Beside from that remaining parameter will get from comparison in between different values of ANSYS results. 821 Copyright Vandana Publications. All Rights Reserved.

4 Sr.No Natural frequency by Aspect ratio(r) Natural frequency by thickness (Mode) a =110 mm,r=0.182 a =108 mm,r=0.185 a =105mm,R=0.190 a =110 mm, R=0.182 t=1.85 mm a =110 mm, R=0.182 t=1.2 mm ( βa) 2 ω (Hz) ( βa) 2 ω (Hz) ( βa) 2 ω (Hz) ( βa) 2 ω (Hz) ( βa) 2 ω (Hz) Phase C-ANSYS C.1] Modal Analysis with ANSYS ANSYS is universal software, which is used on simulation of the interactions in physics structures, vibration, fluid dynamics, thermal transfer and electro mechanics for engineers. We can simulate with ANSYS structures and then test them in the virtual environment. ANSYS can import CAD data and sketch of the geometry. ANSYS Workbench is a platform, which integrates simulation technologies and parametric CAD systems with unique automation and performance Fig.II.C(5.b) Graphical environment of ANSYS Workbench C.2] Test Specimens:- Spring steel are chosen with same b/a ratio i.e. aspect ratio (Inner to outer radius ratio).following are the material properties for the specimen tile cutter. Young s modulus (E) = 2.1 X N/m 2 Poisson s ratio (γ) = 0.3 Density of material (ρ) = 7800 kg/m 3 Dia =110 mm, t= 1.85mm, N=14500 rpm C.3] Different changes:-specimens with variable increase in no. radial crack, increase length of radial crack, slot end hole diameter, geometry of cutter tooth, enlargement of stress concentration holes, different thickness, aspect ratios, different no of cutting teeth are selected. These specimen sizes are chosen to facilitate the measurements by using the same fixture for all the specimens. As boundary conditions for cutter are inner edge fixed and outer edge free. Different no of tile cutter for calibration. C.4] Results :- 1) Original cutter 110 mm od and 20 mm id 822 Copyright Vandana Publications. All Rights Reserved.

5 2) Making 2 mm dia.(120 deg) In between od 110 mm and id w.r.t. same teeth (9 )and slot end dia.4 mm 3) Making 5 mm dia..(120 deg) In between od 110 mm and id w.r.t. same teeth(9 ),slot end dia. 4 mm 4) Increasing slot end dia. Upto 6 mm W.r.t. same teeth (9 ) and od 110 mm 823 Copyright Vandana Publications. All Rights Reserved.

6 5) Reducing no of teeth (10 to 9) w.r.t. same slot end dia. 6mm and od 110 mm 6,7)Increasing od (105 mm and 108 mm) (less aspect ratio) w.r.t. same teeth (8 ) and slot end dia.(4 mm) 824 Copyright Vandana Publications. All Rights Reserved.

7 8) Reducing thickness upto 1.6 mm with one hole in between same od 110 mm and id w.r.t slot end dia for 4 hole as 4 mm and for 5 hole 6 mm with same teeth (9) 9) Making 3 cracks of length 24.5 mm with 2 mm dia of end circle w.r.t. same teeth (9) and od 110 mm. 10)Making 3 cracks of length 24.5 mm with 2 mm circular end crack w.r.t. same teeth (9) and od110mm. 11)Making 3 cracks (120 deg.)of length 24.5 mm from centre w.r.t. same teeth (9) and od 110 mm. 825 Copyright Vandana Publications. All Rights Reserved.

8 12) Making 6 cracks (60 deg.)of length 24.5 mm from centre w.r.t. same teeth (9) and od 110 mm. 13) Making 9 cracks (40 deg.)of length 24.5 mm from centre w.r.t. same teeth (9) and od 110 mm. 14) Making 3 cracks (120 deg.)of length 30 mm from centre w.r.t. same teeth (9) and od 110 mm. 826 Copyright Vandana Publications. All Rights Reserved.

9 15) Making 6 cracks (120 deg.)of length 30 mm from centre w.r.t. same teeth (9) and od 110 mm. Phase D-COMPARISSION Adopting analysis procedure as per discuss in chapter II (Phase c) gives natural frequency in every tile cutter as tabulated in bellow. Also phase II (C.5.a) will gives total deformation as sample 2 nd no cutter. based on that same procedure apply other and comparison in terms of vibration commented in conclusion. I] ASPECT RATIO AND THICKNESS- By comparing ANSYS results with theoretical formula by considering only two parameter i.e. aspect ratio and thickness will gives that as both are same. In tabulated form gives theoretical values also cutter no (1),(6),(7) &(8) will gives ANSYS analytical value w.r.t. aspect ratio (cutter (1),(6) & (7)) and thickness (1 & 8).Finally both results are conclude that as Aspect ratio increases natural frequency also increases and as thickness decrease natural frequency also decreases which tabulate in bellow table. II] OTHER PARAMETER - Compare every cutter result by referring ANSYS and deformation result as mentioned above cutter.(original cutter is 1 st number) a) Making stress concentration holes (cutter 2) and enlargement them (cutter 3)-Compare cutter 1,2 &3 Sr.No Natural frequency(hz) by Aspect ratio(r)(cutter 1,6,&7) Natural frequency by thickness (CUTTER 1&8) (Mode) a =110 mm,r=0.182 (CUTTER 1) a =108 mm,r=0.185 (CUTTER 6) a =105mm,R=0.190 (CUTTER 7) a =110 mm, R=0.182 t=1.85 mm(cutter 1) a =110 mm, R=0.182 t=1.2 mm(cutter 8) Theoretical ANSYS Theoretical ANSYS Theoretical ANSYS Theoretical ANSYS Theoretical ANSYS b) Increasing slot end diameter (cutter 4) and Number of teeth (cutter 5) Compare cutter 1,4 &5 827 Copyright Vandana Publications. All Rights Reserved.

10 Sr Natural Frequency ( ω in Hz) No. Mode Cutter 1 (Original 9 teeth 4mm slot end dia.) Cutter 4 (9 teeth & Increasing slot end diameter i.e.6 mm) Cutter 5 (Increasing slot end 6 mm with10 teeth) Sr.No. Natural Frequency ( ω in Hz) Mode (3 cracks) (6 cracks) Cutter 11 (24.5 mm crack length) Cutter 14 (30 mm crack length) Cutter 12 (24.5 mm crack length) Cutter 15 (30 mm crack length) C) Variable radial slit (cutter 9) and circular concentric slit (cutter 10) - Compare cutter 1, 9 & 10 Sr No. Natural Frequency ( ω in Hz) Mode Cutter 1 (Original) Cutter 9 (3 cracks of length 24.5 mm with 2 mm dia. end circle ) Cutter 10 (3 cracks of length 24.5 mm with 2 mm circular end crack ) d ) Increasing number of cracks of same length 24.5 mm from centre with same teeth and outer dia.- Compare cutter 11,12 & 13. Sr No. Natural Frequency ( ω in Hz) (cracks from same length 24.5 mm) Mode Cutter 11 (3 cracks) Cutter 12 (6 cracks) Cutter 13 (9 cracks) Copyright Vandana Publications. All Rights Reserved.

11 III. CONCLUSION REFERENCES Thus vibration analysis of circular tile cutter is done by using some theoretical and ANSYS as analytical method also by referring DEFORMATION value we will comment on vibration created in every tile cutter. From overall ANSYS and theoretical result it can gives that as, a) Aspect ratio increases natural frequency increase. Also vibration will minimum in high aspect ratio tile cutter.(cutter 1,6& 7) b) Thickness of tile cutter reduced then natural frequency also reduced. But vibration will more in reduced thickness tile cutter.(cutter 1 &8) c) By making and enlargement of stress concentration holes natural frequency reduced. But enlargement of dia. of hole may cause high vibration (cutter 3) than only making of holes (cutter 2). So selected only making of mini. dia of holes causes less vibration. d) Increasing slot end dia. natural frequency will minimum and as vibration also minimum.(cutter 1 &4 ) e) Increase in number of teeth natural frequency will increases and vibration also increases.(cutter 4& 5) f) By making 3 cracks at end of crack there is small hole having low natural frequency and high vibration than same no of crack but at end of crack there is small circular crack.(cutter 9 & 10) g) Increasing no of cracks from 3 to 6 of same crack length (24.5 mm) natural frequency decreases with increase in vibrations. Next 6 to 9 cracks natural frequency and vibration both will increased. So select tile cutter with minimum no of cracks, up to 6 cracks will be fine w.r.t. mini. vibration.(cutter 11,12&13) h) Increasing length of cracks (30 mm) with same no of cracks ( 3 or 6) natural frequency will decreases but vibration will more. So select minimum length of crack and minimum no of crack for minimum vibration than original cutter (1) (cutter 11,12, 14 & 15) 1.W.M. Lee a, J.T.Chen Eigensolutions of a circular flexural plate with multiple circular holes using the direct BIEM and addition theorem journal of Engineering Analysis with Boundary Elements 31 July 2010, L. Cheng*, Y.Y. Li, L.H. Yam Vibration analysis of annular-like plates Journal of Sound and Vibration 262 (2003) Sasank Sekhar Hota, Payodhar Padhi Vibration of plates with arbitrary shapes of cutouts Journal of Sound and Vibration 302 (2007) D.V.Bambill, S.La.Malfa, C.A.Rossit, P.A.A.Laura, Analytical and Analytical Investigation on Transverse Vibration of Solid, Circular and Annular Tile cutters Carrying a Concentrated Mass at an Arbitrary Position with Marine Applications, Journal of ocean Engineering, vol31, pp K. Ramesh, D.P.S. Chauhan and A.K. Mallik, Free Vibration of Annular Tile cutter with Periodic Radial Cracks, Journal of sound and vibration, 1997, 206(2) pp J.C. Bae and J.A. Wickert, Free Vibration of Coupled Tile cutter-hatstructures, Journal of sound and vibration, (2000) 235(1) pp M. Haterbouch,R. Benamar Geometrically nonlinear free vibrations of simply supportedisotropic thin circular plates Journal of Sound and Vibration 280 (2005) P.A.A. Lauraa, U. Masia b, D.R. Avalosb, Small amplitude, transverse vibrations of circular plates elastically restrained against rotation with an eccentric circular perforation with a free edge Journal of Sound and Vibration 292 (2006) W.T. Norris and J.E.T Penny, Revisitation of the Computation of the Resonant Frequencies of an Annular Tile cutter Encastred at its Inner Edge and Free at its Outer Edge, Dec 2002, AstonUniversity. 10.Chi-Hung Huang, Vibration of Cracked Circular Tile cutters at Resonance Frequency Journal of Sound and < vibration (2000) pp Copyright Vandana Publications. All Rights Reserved.