Mechanically responsive and antibacterial plasma polymer coatings for soft biomaterials

Transcription

1 Mechanically responsive and antibacterial plasma polymer coatings for soft biomaterials E.Kulaga, T.Bourgade, L.Ploux, V.Roucoules Institut de Science des Matériaux de Mulhouse, IS2M-CNRS-LRC7228, 15 rue Jean Starcky, 68057Mulhouse, France Abstract: In this paper we develop a new strategy to obtain antibacterial coating leading to adaptive release processes. This work is based on the plasma polymerization process and on mechanically reversible fragmentations. Keywords: Plasma polymerization, antibacterial coatings, controlled release 1. Introduction 2. Strategy Nanoscaled materials have found a broad application range in different fields, such as microelectronics [1], medical applications [2], or textile finishing [3]. Especially in the medical field, new materials are often investigated regarding their antibacterial properties [4]. Indeed, despite strict antiseptic operative procedures to minimize microbial contaminations, bacterial infection significantly raises postoperative complications of surgical procedures. The consequences of implant infections are serious and they remain the main causes of revision surgery [5]. Controlled release of bioactive agent was achieved by the fabrication of plasma polymer multilayer systems [Figure 1], which consist of two layers of Maleic Anhydride Plasma Polymer deposited on the surface of Polypropylene made surgical mesh. In between plasma polymer layers silver nanoparticles are trapped as an antibacterial agent reservoir. Owing to differences between mechanical properties of the plasma-polymer thin films and the elastic bulk substrates, tensile strengths generate cracks within the plasma polymer, which might be used as diffusive channels for bioactive substances located under the plasma polymer thin film. Over the last few years, new strategies have been proposed to control and prevent microbial contamination of implants. One of the promising approaches is to adjust the antimicrobial properties of the implant surface. Especially multifunctional systems with immobilized antibacterial agents, which exhibit long term durability and reduced development of drug-resistant mutation, are promising. In this context we are exploring the potential of elaborating new antibacterial coatings via a plasma polymer functionalization step. These coatings contain and release in a control way an optimal amount of bioactive agent, which helps to prolong the lifetime of antibacterial properties of material. Figure 1. Scheme of the designed multilayer system. The originality of this system is that the aperture of the crack can be controlled mechanically in a reversible way. In the field of textiles and other soft biomaterials, this strategy is promising due to the mechanical stresses that naturally occur at the implant location.

2 3. Experimental Part Materials: An undyed, knited, pure polypropylene (PP) mesh (Cousin Biotech) was used in this study. Briquettes of maleic anhydride (99.5% purity) were provided from Sigma-Aldrich and were used as received. Silver nitrate solution 0,1N was purchased from Sigma-Aldrich. NaBH4 (98% purity) was purchased from Sigma-Aldrich. Plasma Polymer Treatment. Prior to use, maleic anhydride was ground into a fine powder and loaded into a stoppered glass gas delivery tube. Plasma treatments were carried out in an electrodeless cylindrical glass reactor (6cm diameter, 680 cm 3 volume, base pressure of 5 x10-4 mbar, and with a leak rate better than 1.0 x10-10 kg.s-1) enclosed in a Faraday cage. The chamber was fitted with a gas inlet, a Pirani pressure gauge, a two-stage rotary pump (Edwards) connected to a liquid nitrogen cold trap and an externally wound copper coil (4 mm diameter, 5 turns). All joints were grease-free. An LC matching network (Dressler, VM 1500 W-ICP) was used to match the output impedance of a MHz radio-frequence (R.F.) power supply (Dressler, Cesar 133) to the partially ionized gas loaded by minimizing the standing wave ratio of the transmitted power. During electrical pulsing, the pulse shape was monitored with an oscilloscope and the average power <P> delivered to the system was calculated using the following expression: <P> = P p [ton / (ton + toff)], where Pp is the average continuous wave power output and ton / (ton + toff) is defined as the duty cycle. PP substrates were placed into the centre of the chamber followed by evacuation back down to base pressure. They were first activated by argon plasma during 1 min at 60W (PP/Ar). Subsequently, maleic anhydride vapour was introduced into the reaction chamber (pressure of 0.2 mbar) with a flow rate of approximately 1.6x10-9 kg.s-1. At this stage, the plasma was ignited and run for 30 min. The deposition conditions correspond to: power output = 20 W, duty cycle = 2% and frequency = 816Hz. Upon completion of deposition, the R.F. generator was switched off and the monomer feed allowed to continue to flow through the system for a further 2 min period prior to venting up to atmospheric pressure. Prior to use, plasma polymer modified substrates were immersed in deionised water to promote the hydrolysis of maleic anhydride groups into dicarboxylic acid groups (PP/Ar/MAPP). Deposition of Antibacterial Agent onto the Plasma Polymer film. Antibacterial agent (in this study Silver (Ag), a well known antiseptic agent) was loaded directly on the PP/Ar/MAPP surface by immersion of the coated substrate onto a 1,0 mm silver nitrate solution for 30 min. Silver cations (Ag+) diffused into the reservoir and formed electrostatic pairs with carboxylate groups. The carboxylate-bound Ag+ ions could be reduced to zero-valent Ag nanoparticles (AgNPs) using aqueous solution of NaBH4 (2,0 mm). Then, the PP/Ar/MAPP/Ag substrate was placed into the chamber of the plasma reactor and the system was pumped down to base pressure. Maleic anhydride vapour was introduced into the reaction chamber at a constant pressure of 0,2 mbar. The plasma was ignited and run for 10 min according to the following conditions: duty cycle = 50% and frequency = 816Hz. Upon completion of deposition, the R.F. generator was switched off, and the monomer feed was allowed to continue to flow through the system for a further 2 min prior to venting up to atmospheric pressure. Finally, the final bioactive coating (PP/MAPP/Ag/MAPP) was sterilized by dry heating (120 C) for 1 hour prior to use. Contact Angle Measurements. Contact angles were measured on pure polypropylene plates with deionised water using an automatic goniometer (Krüss DSA 100W). Before each measurement, substrates were dried under nitrogen stream. Three droplets were deposited on the surface and two independent measurements were performed on each droplet. SEM. SEM observations were performed using an FEI environmental microscope (Quantana 400 model) working at 30 kev. TEM. Transmission electron microscope (TEM) observations have been performed using a Philips CM200 microscope working at an acceleration voltage of 200 kv. X-ray photoelectron spectroscopy (XPS). XPS spectra of functionalized surfaces were recorded

3 4. Results and discussion High resolution XPS analysis of the C(1s) envelope of PP/Ar/MAPP surface revealed five different types of carbon functionalities: hydrocarbon (CHx ~ ev), carbon singly bonded to carboxylic acid group (-C-C(O)=O ~ ev), carbon singly bonded to oxygen (-C-O ~ ev), carbon doubly bonded to oxygen (O-C-O/-C=O ~ ev) and carbon from carboxylic acid groups (-C-C(O))=O ~ ev). The following infrared absorption features of cyclic anhydride groups were identified: asymmetric and symmetric C=O stretching (1860 cm-1 [D] and 1796 cm-1 [C]) and a broad band centered at 1730 cm-1 which is attributed to the overlap between free carboxylic band at 1740 cm -1 [B], the intermolecular hydrogen-bonded carboxylic acid band at 1720 cm-1 [A] and the intramolecular hydrogen-bonded carboxylic acid band at 1685 cm-1 [Figure 2]. Presence of band [C], indicates that hydrolysis had not occurred in the entire thickness of the plasma polymer film. The thickness of the PP/Ar/MAPP layer is estimated to 20 nm. [A] [B] [C] [D] Absorbance [a.u.] with a VG SCIENTA SES-200 spectrometer equipped with a concentric hemispherical analyzer. The incident radiation used was generated by a monochromatic Al Kα x-ray source (1486,6eV) operating at 420 W (14kV; 30mA). Photo-emitted electrons were collected at a take-off angle of 90 from the substrate, with electron detection in the constant analyser energy mode. Survey spectrum signal was recorded with a pass energy of 500 ev and for high resolution spectra (C1s and O1s) pass energy was set to 100 ev. The analysed surface area was approximately 3 mm 2 and the base pressure in the analyse chamber during experimentation was about 10-9 mbar. Charging effects on these isolating samples were compensated by the usage of a Flood Gun. The spectrometer energy scale was calibrated using the Ag 3d5/2, Au 4f7/2 and Cu 2p3/2 core level peaks, set respectively at binding energies of 368.2, 84.0 and ev. Peak fitting was made with mixed Gaussian-Lorentzian (30%) components with equal full-width-at-half-maximum (FWHM) using CASAXPS software. The surface composition expressed in atom% was determined using integrated peak areas of each components and take into account transmission factor of the spectrometer, mean free path and Scofield sensitivity factors of each atom (C1s: 1.00 and O1s: 2.93). Bacterial Culture. Experiments were conducted with the Escherichia coli (E.coli) K12 (MG1655) strain.. 1ml of bacteira stock culture (stored at -80 C) was used to inoculate 10 ml of selective growth medium (M63G, ph=6,8), resulting in a preculture that was further growth overnight at 30 C. This culture was used to inoculate a second preculture (10 vol.-% of the last preculture), which was grown for 4h in the same conditions. 100 µl of this fresh bacterial suspension was spread on LuriaBertani (LB) agar-supplemented growth medium (15gL-1) in order to form a thin bacterial film. Antibacterial Assay. The sterilized samples were placed in contact with previously homogeneously inoculated agar plates (with the top side of the samples in contact with the agar). After overnight incubation at 30 C, bacterial growth around the samples was observed in order to identify the potential presence of zones without bacterial growth (growth-inhibition areas). PP_Ar_MAPP_3Ag_MAPP PP_Ar_MAPP_Ag PP_Ar_MAPP_hydrolysis PP_Ar PP Wavenumber [cm ] Figure 2. ATR-FTIR spectra of each step of multilayer system preparation. The carboxylic acid groups allowed to attach silver ions (Ag+) by dipping the coated substrate into a silver nitrate solution. Then, the Ag + ions were reduced to zero-valent AgNPs using NaBH 4 aqueous solution as a reluctant. Analyses of TEM images [Figure 3] of the AgNPs deposited on MAPP surface showed a narrow size distribution without undesired aggregation.

4 Figure 3. TEM images of AgNPs deposited on the PP_Ar_ MAPP surface Then a second plasma polymer, which was deposited on the previously prepared system, covers most of the AgNPs. Once again typical anhydride and carboxylic acid groups infrared bands are observed, see Figure 2. The thickness of this second plasma polymer layer was estimated to 120 nm. Only traces of silver can be detected in the ~10 nm interfacial depth region. XPS analysis and contact angle measurements are in good agreement with each step of the aforementioned procedure [These results will be detailed during the oral presentation]. Transmission Electron Microscopy photograph confirms that AgNPs are trapped between the two plasma polymer layers (see Figure 4) and shows that this step does not affect the size and the AgNPs. Figure 5. SEM images of PP/Ar/MAPP/Ag/MAPP mesh sample before stretching (a) and after stretching (b,c). When the PP/Ar/MAPP/Ag/MAPP substrate was stretched cracks appeared in the coating as shown on the Figure 5 due to the differences in the mechanical properties of the plasma polymer film and the bulk substrate. Density and size of cracks were controlled during this process. We also demonstrated that, when the material was no longer elongated, cracks were closed until mechanical strength appeared again. This gave the opportunity to control the flux of the antibacterial agent by the mechanical stimulation. [This point will be discussed during oral presentation]. Figure 4. TEM micrograph of PP/Ar/MAPP/Ag/MAPP sample The top layer of cross-linked plasma polymer network acted as a barrier and reduced significantly the delivering process of the AgNPs into the surrounding aqueous environment. This point can be easily demonstrated by UV spectroscopy as demonstrated in reference [6]. Figure 6. Bacterial growth on nutritive agar plates in the surroundings of a) PP/Ar/MAPP/Ag system; b) PP/Ar/MAPP/Ag/MAPP system; c) PP/Ar/MAPP/Ag/MAPP system under stretching.

5 Barrier role of the plasma-polymer overlayer and the recovery of the antibacterial action through the elongation-related cracks were verified by a preliminary microbiological experiment. Bacterial growth was observed around samples placed on agar plates [Figure 6]. In case of system PP/Ar/MAPP/Ag, without the plasma polymer overlayer, bacterial growth around sample is inhibited [Figure 6a] as a result of silver delivery from the sample. Bacterial colonization aroundpp/ar/mapp/ag/mapp sample is not inhibited [Figure 6b] which shows a barrier effect of plasma polymer overlayer. Recovery of antibacterial effect coming from silver nanoparticles attached in between two plasma polymer layers in system PP/Ar/MAPP/Ag/MAPP can be achieved by mechanical stimulation [Figure 6c]. By stretching sample cracks are induced in order to provide diffusive channels for antibacterial agent. By taking advantage of open/close crack system it is possible to control flux and prolong the lifetime of antibacterial coating. 5. Conclusion Mechanically sensitive architectures made of macromolecules and bioactive agents are constructed on the modified polypropylene substrate, using solvent-free steps. Here, the behavior of the films is presented in terms of elongation-dependent releasing measurements. This work puts a light on original approach offering a great opportunity to readdress the persistent challenge of obtaining effective and long-lasting antibacterial coatings. References [1] J. M. Grace, L. J. Gerenser, J. Dispersion Sci. Technol. 2003, 24, 305 [2] X. Chen, H.J.Schluesener, Toxicology letters 2008, 176, 1-12 [3] D. Hegemann, D.J. Balazs, Plasma technologies for textiles, R. Shishoo, Ed., Woodhead, Cambridge 2007, p.158. [4] Z. Li, D. Lee, X. Sheng, R.E. Cohen, M.F. Rubner Langmuir, 2006, 22, [5] A. Engelsman, H. van der Mei, R. Ploeg, H. Busscher, Biomaterials, 2008, 27, [6] A. Airoudj, E. Kulaga, V. Roucoules, L. Ploux, Advanced Engineering Materials, 13: n/a. doi: /adem