SM6-36 English distribution HTA adaptation instructions motorisation of a CI1 or CI2 operating mechanism
SCHNEIDER ELECTRIC foreword symbols and conven ons you w ll f d all the symbols below throughout the document, nd c g the hazard levels depend ng on the d erent types of s DANGER as per so 3864---2 DANGER : fa re to follow th s struct on l result n death or ser ous njury. WARNING as per so 3864---2 WARNING: fa ure to follow th s nstruct on may result n death or ser ous njury. CAUTION as per so 3864---2 CAUTION: fa ure to follow th s nstruct on may result n r es. Th s alert nal can also be used to nd cate pract ces that could damage the SM6 un t. INFORMATION- ADVICE We draw your attent on to th s spec f c po t. S1B22874 rev s on : 02 1
contact the Sc der Electr c serv ce t for d ag s and ad ce Call your sales representat ve who l put you n contact w th the closest SCHNEIDER ELECTRIC group serv ce centre. You can log on to: www.schne der---electr c.com str bu on rules CAUTION CAUTION The a m of s publ on s to enable the SM6 un t to be stalled correctly. Th s document s not a commerc al document.it s a st ctly techn cal document drawn up by Schne der Electr. 2 S1B22874 rev s on : 02
safety rules CAUTION CAUTION All the operat ons desc ed below must be performed n comp ance th a cable safety standards, under the respons b ty of a competent author ty. Only undertake the work after hav ng read and understood all the explanat ons ven n th s document.if you have any d culty comply ng w th these rules, please contact Schne der Electr. WARNING The contractor must be cer f ed and author sed to m pulate and perform work on the SM6 t. S1B22874 rev s on : 02 3
4 S1B22874 rev s on : 02
general concern ng th s document Th s pu cat on s ntended str ctly for use w th n Schne der Electr c and s not a sales document. It conta ns nstruct ons concern ng the mod f cat on or the adaptat on of assem es. The parts referred to form part of a k t and are not ava able separately. Th s document may not be reproduced n any form or by any means and s reserved exclu vely for use by Schne der Electr c representat ves. safety requ rements The s tch for the cub cle n wh ch the motor mechan sm s to beadded or changed must be n open po t on. CI2: the operat ng mechan m must be charged. The busbars or cables can rema n ene ed. After replac ng the motor mechan m and for ver f cat on, the sw tch must bede---energ sed on both the busbar and cable s de. spec al tools 1 torque wrench 1 to 50 Nm. 1 spec al lock ng tool n 3728698 and a padlock w th an 8 mm d ameter shackle. prepar ons The operat ons requ red for access to the operat ng mechan m and reassembly of the cub cle are desc ed n the correspon ng nstruct on manual. f eld of appl t on No rest ct ons. S1B22874 rev s on : 02 5
access to the subassembly 1 : LV compartment cover mount ng hardware 2 : 2 bolts M6x12 3 : 2 contact washers 4 : operat ng mechan m cover mount ng hardware 5 : 4 cross recess screw M6x30 6 : 4 2 3 1 4 5 6 6 S1B22874 rev s on : 02
general descr on contents of CI1 k t no. 9017989x (x depends on the voltage) A : connect on subassembly (CIP2) B : relay subassembly (CIP1) C : aux ary contact subassembly D : motor E : speed reducer F : m cro--- tch S13 actuator G : lock---out m cro---sw tch S13 H : lock---out m cro---sw tch S14 J : connect on term nal block K : LV fuse rat ng label L : m cro--- tch S21 M : P1 mulator N : open ng release 1 bag of nuts and bolts 1 w re bundle 1 label dent fy ng the elect cal operat ng mechan m CI1 / Q T : m cro--- tch S18 D E B C A K L J M H F N G / T S1B22874 rev s on : 02 7
contents of CI2 k t no. 9017990x A (x depends on the voltage) A : connect on subassembly (CIP2) B : relay subassembly (CIP1) C : aux ary contact subassembly D : motor E : speed reducer F : m cro--- tch S13 actuator G : lock---out m cro---sw tches S13 S15 and S16 H : lock---out m cro---sw tch S14 J : connect on term nal block K : LV fuse rat ng label L : m cro--- tch S21 M : P1 mulator N : open ng release P : m cro--- tch S20 Q : lock R : m cro--- tch S17 S : clo ng release 1 bag of nuts and bolts 1 w re bundle 1 label dent fy ng the elect cal operat ng mechan m CI2 / Q T : m cro--- tch S18 B C D Q P E R K L J M H S G F N / T 8 S1B22874 rev s on : 02
procedure d smantl ng the operat ng mechan sm B A Remove the voltage presence nd cator. (remove bolts A) Cut t es B. F t lock ng tool n 3728698. Rotate through 180. Prevent any transverse movement of the tool by f tt ng the padlock w th the 8 mm d ameter shackle. C For cub cles equ ed th a mechan cal fuse blown n cat on, ref t ng C. Remove the 3 bolts secur ng the operat ng mechan m and w thdraw the latter. S1B22874 rev s on : 02 9
mount ng the motor on the speed reducer for clar ty n the prese on of the nformat on n th s manual, the mount ng of the motor w ll be descr bed f rst. Note that the overall procedure s eas er f t s mounted at the end. Unscrew the mult funct on plate. (3 HM5 screws) Remove the mult funct on plate w th the lever lockout bar. Secure the motor w th 2 M5 bolts, 1 spacer and 2 nylstop nuts. T gh g torque : 2,5 Nm. Secure the rocker and the gear motor assembly. F t m cros tch S21. Bolt T ghten ng torque: 8 Nm. (CI1) or f t m cro tches S17 and S21. Bolt. T ghten ng torque: 8 Nm. (CI2). 10 S1B22874 rev s on : 02
For a CI1 pr or to June 95, remove the ngle cam and mount a double cam. For a CI2 pr or to June 95, mount a double cam. Mount the m cro tch cam. T hten the cup---po nt screw and secure th loc te h h---strength thread lock ng compound. T ght g torque: 15 Nm. (CI2) Screw on the d tance sleeves. T ghten ng torque: 4,5 Nm. Install the loc ng system and the nuts. T ghten ng torque: 4,5 Nm. For operat ng mechan sms pr or to August 95, f t the bolts and block the nuts. T ghten ng torque: 8 Nm. Secure the CIP1 subassembly w th 2 nylstop nuts. T ghten ng torque: 8 Nm. dc supply jumpers R1 and R2 removed. ac current d odes D1, D2, D3 and D5 removed., S1B22874 rev s on : 02 11
As of August 95, secure subassembly CIP1 2 nylstop nuts. T ghten ng torque: 8 Nm. th Mount m crosw tch S14 and a n the top edge of the m crosw tch support bracket w th the top edge of the front plate. 2 HM4 x 12 bolts and 2 nylstop nuts. T ghten ng torque: 2,8 Nm. Us ng a bell ---tester, check that m cro---sw tch S14 sw tches when the earth ng sw tch operat ng lever s nserted and removed. If t does not, adjust the po t on of the m cro---sw tch support. Mount the aux ary contact support. 7, 9 or 12 contacts (the short bolt should be on top and the long one on the bottom). T ghten ng torque: 8 Nm. 12 S1B22874 rev s on : 02
F t the sp ng and screw on the nut w thout t ghten ng t. Leave 7 mm between the two nuts. Mount the three m crosw tches S13, S15 and S16. T ghten ng torque: 0,4 Nm. A Us ng a bell ---tester, check that m cro---sw tch S13 sw tches when the sw tch operat ng lever s nserted and removed. If t does not, adjust the po t on of the m cro---sw tch support. Mount the ratchet system, w thout apply ng exce ve force. T ght g torque: 28 Nm. F t the necessary p ns, grease and apply lock ng compound to the correspon ng parts. A : glue hard type loct te (green 270) S1B22874 rev s on : 02 13
Mount the clo ng release and ts support n the CI2 operat ng mechan. T ghten ng torque: 5,5 Nm. t the w of the co. ng from the top To screw the open ng release on ts support, T ghten ng torque: 2,8 Nm. To screw all and the tr ng blade n the operat ng mechan m. T ghten ng torque: 5,5 Nm. F x the m cro---sw tches S18 and S19 T ghten ng torque: 0.4 Nm before to mount the open ng release on ts support T ghten ng torque: 2,8 Nm. To screw all and the tr ng blade n the operat ng mechan m. T ghten ng torque: 5,5 Nm. t the w ng v a the front of the operat ng mechan m. 14 S1B22874 rev s on : 02
r g the mult funct on plate and the lever lockout bar B A The blade of m crosw tch S14 (A) must be located under the branch of the lever lockout bar ( B ). Deta l show ng the ng path beh nd the voltage presence n cator. Mount the mult ---funct on plate and the lever lockout bar. Mount the lock ng blade. P1 Secure the mulator P1 w th 2 tap screws. T ghten ng torque: 2,5 Nm. M4 x 25 screws, 4 mm d ameter contact washer, M4 nut. The motor should be mounted now. Connect the 2 w res beh nd the motor. Secure (2 bolts, 2 M4 nylstop nuts and 1 spacer: T ghten ng torque: 0,25 Nm, w th the spacer and the head of the bolt n e the speed reducer). S1B22874 rev s on : 02 15
remount ng the operat ng mechan sm Mount the operat ng mechan m, respect ng the 6 follo ng po nts. 1 : the c symbol must be n the po t on nd cated above. (sw tch n open po t on). A B C 2 : lhe crankshaft of the operat ng mechan m must f t n the hole ( A). 3 : the crank of the downstream earth sw tch ( B ) must po nt to the ht of the operat ng mechan m. In add t on, on PM, QM and QMC cub cles, the p n ( C ) on th s crank must f t ns e the slot n the connect ng rod of the downstream earth ng sw tch. 4 : the pusher n must f t n e the hole of the lever lockout bar lock. 16 S1B22874 rev s on : 02
D 5 : for the cub cles w th fuse blown mechan c equ ped, f x the ng D. 6 : the m cro sw tches blades S18 and S19 must be under the nd cator. P Q U ng the three new contact washers, ref t the three bolts for the operat ng mechan m. T ght g torque: 28 Nm. Remount the voltage presence n cator u ng bolts ( P ) HM 4x10 + the M4 nylstop nuts that come w th the k t. T gh g torque : 1,5 Nm. t the t e (Q). Remove the lock ng tool. F t the two cage nuts. S1B22874 rev s on : 02 17
1 2 1 : from the outs de of the cub cle, nsert the cage nut n the square hole. 2 : rotate the cage nut so that t s ts nearly vert cally th n the cub cle. 3 4 3 : push the cage nut n the ect on of the arrow so that the top of the cage c ps beh nd the panel. 4 : the nut s correctly po t oned. S4 S1 S5 S7 S8 S10 S11 S9 S12 S2 S3 S6 Secure the CIP2 support and apply the LV fuse rat ng label. M cro sw tch references for w ng. CAUTION Be careful : don t use the w e n o 14 / CIP1---8. ( t s used only for CIT) : solate t or cut t n order to save takes. W e as shown n the w ng d agram, f tt ng the necessary t es. 18 S1B22874 rev s on : 02
SM6 --- CI1/I w r ng d ram --- note: the subassem es come conf ured for the current spec f ed w th the order. AC : D1/D2/D3/D5/D6 removed --- DC : R1/R2 removed S1B22874 rev s on : 02 19
SM6---CI1/Q w r ng d ram --- note: the subassem es come conf ured for the current spec f ed w th the order. AC : D1/D2/D3/D5/D6 removed --- DC : R1/R2 removed 20 S1B22874 rev s on : 02
SM6---CI2/I w r ng d ram --- note: the subassem es come conf ured for the current spec f ed w th the order. AC : D1/D2/D3/D5/D6 removed --- DC : R1/R2 removed S1B22874 rev s on : 02 21
SM6---CI2/Q w r ng d ram --- note: the subassem es come conf ured for the current spec f ed w th the order. AC : D1/D2/D3/D5/D6 removed --- DC : R1/R2 removed 22 S1B22874 rev s on : 02
operat ng mechan sm ref ng Ref t the operat ng mechan sm cover Screw the M6x35 cross recess screws. tak ng care not to p nch the bundle of es (use the notch prov ded). Ref t the LV cover T ghten ng torque: 8 Nm. Label nd cat ng that the operat ng mechan m s motor ---d ven, secured to the cover by 2 plast c vets. CI1. Dr l holes on the c panel us ng the holes v ble n de the cover as a gu de. CI2. S1B22874 rev s on : 02 23
24 S1B22874 rev s on : 02
ss g and m tenance truct ons operat ng checks - carry out 3 open ng/clo ng cycles : the durat on of each operat on should not exceed 9s. - auto---ene at on check : n t ate a cha ng or clo ng operat on by an mpulse type order; the correspond ng operat on should be ca ed out completely. - ant ---pump ng check : send open ng and clo ng orders at the same t me. > sw tch open : the tch should rema n open. : f the open ng order s released, the sw tch should close (clo ng order ma nta ned). : f the clo ng order s released, the sw tch should rema n open. > sw ch closed : the sw tch should open and rema n open. - check the elect cal lock ng systems : > t should be o e to close the s tch elect cally f the operat ng lever s nserted n the earth ng sw tch operat ng mechan. > t should be o e to close the s tch elect cally f the operat ng lever s nserted n the sw tch operat ng mechan m. - check that the po t on nd cat on contacts operat ng correctly (accord ng to the d agram used). note : elect cal tests are ca ed out from the customer s term nal block. f electr cal operat on cannot be checked, use a bell---tester to check the sw tch g of m ro---sw tches S13 and S14 when sert g and remo g the operat g lever. S1B22874 rev s on : 02 25
trouble---shoot ng table The electr al opera g mechan sm does not work - Check the LV fuses (CIP2). H Check the elect cal locks S13 and S14 (lever nsert on). - Check that the operat ng shaft of the earth ng sw tch s all the way to the open po t on. - Check that contact S14 s not block ng the supply of power; f necessary re---adjust t. - Check the conf urat on of subassembly CIP1 (see d agram). 26 S1B22874 rev s on : 02
S1B22874 rev s on : 02 27
28 S1B22874 rev s on : 02
Schne der Electr c serv e centers are there for: en nee ng and techn cal a tance start-up tra n ng prevent ve and correct ve ma ntenance adaptat on work spare parts Call your sales represe ve who w ll put you n touch w th your nearest der Electr c serv ce centre. Schne der Electr c Industr es SAS 89, boulevard Frankl n Roosevelt F--- 92500 Rue l--- Malma son (France) Tel : +33 (0)1 41 29 85 00 http://www.schne der--- electr c.com S1B22874 rev s on : 02 As standards, spec cat ns and des gns change from t me to t me, please ask for con rmat n of the nformat n g ven n th s publ cat n. Concept on, rédact on: Serv ce Documentat on Techn que T&D Ed t on : 26/07/2011