: The T Series is designed for hybrid circuit and low profile printed circuit board applications where inductance is to be minimized, or where substrate space is at a premium. They can be attached to substrates or circuit boards by dipsoldering, welding, re-flow soldering or other conventional methods. These units have the further advantage of being compatible with automatic assembly equipment-minus the problems associated with flexible terminal lead wires. Our chip tantalums meet all EI sizes. RTINGS apacitance Range: 0.1µF to 0µF Tolerance Range: M(±20%), K(±%) Rated Voltage: 4V to 50V ITEMS Operating Temperature Range Maximum Working Temperature Rated Voltage Range apacitance Range Standard apacitance Tolerance Dissipation factor (tan δ) SPEIFITIONS, PERFORMNE -55 ~+85 (+125 ) +85 (+125 with derating) 4 VD ~ 50 VD 0.1µF ~ 0µF ±20% (M) ±%(K) 0.1~µF 4.0% ~0µF 6.0% Not more than 0.01V or 0.5µ, whichever is greater TEST ONDITIONS See Table of Standard Ratings JIS--52 20 120Hz JIS--52 20 120Hz JIS--52 20 (5 minutes) (after rated voltage applied) Temperature Temp. Stability -55 +125 Surge Voltage Solder Heat Resistance Humidity Test High Temperature Test Failure Rate at 85 Max ±12% Max. ±15% apacitance hange Dissipation Factor Max. tan δ 0.1 ~ µf 6.0% ~ 0µF 8.0% 0.1 ~ µf 6.0% ~ 0µF 8.0% Less than ±5% Less than specified value Withstand solder immersion 5 seconds at 260 or reflow seconds at 260 apacitance hange Dissipation Factor apacitance hange Dissipation Factor 1% per 1,000 hours Less than ±5% Less than initial specified value Less than ±% Less than initial specified value Max. N 0.125V or 6.25µ whichever is greater -0 JIS--5140 and 52 85 Surge voltage applied, 00 times with series resistance of 00Ω for 30 seconds at intermittent intervals of 5 minutes JIS--52 at 60 humidity 90% ~ 95% RH, 500 Hours JIS--52 85, Rated voltage 2000 hours or 125 Derating voltage 00 hours with circuit resistance of 1Ω/V MTBF 5 X 4 Hr. Procedure: 1. 20±2 2. -55 +0-3 Stabilized 3. 20±2 15 min. 4. +125+3 2 hrs. 31
Ordering Information & Marking Ordering Information Example: 1 MFD 16 volt 20% T M I 5 T Series Destination apacitance Tolerance Rated Voltage apacitance Size Taping & Packaging apacitance Tolerance ±20% ±% ode M K Rated Voltage 2 4 6.3 16 20 25 35 50 ode OD OG OJ I I ID IE IV IX apacitance (ex) 0.1 ~ 0.68µF ~ 6.8µF ~ 470µF ode 4 ~ 684 5 ~ 685 6 ~ 477 R: Decimal Point - First two digits represent significant figures and the third digit specifies number of zeros to follow. apacitance unit is µf. MRKING - Size ex) 6.3V-µF FREQUENY HRTERISTI URVES () apacitance: First two digits represent capacitance and the third digit specifies number of zeros to follow. apacitance unit is µf. ex) V-µF B,, D - Size 32 Note: See back cover for low ESR information
STNDRD RTINGS ND SE SIZE DISTRIBUTION* Rated Voltage @ +85 Surge Voltage @ +85 Derated Voltage @ 125 Derated Surge Voltage @ +125 apacitance µf 0.1 0.15 0. 0. 0.47 0.68 3.3 4.7 6.8 15 47 68 0 150 0 4 5.2 2.7 3.4 B/ B/ E 6.3 8 4 5 / B/ B/ / / B/ 13 7 9 / B/ B/ / /D 16 20 12 B/ B/ / /D *Letter code after / indicates new extended range. Please indicate size code on ordering. 20 26 13 16 / B/ /D /E 25 32 17 B/ B/ E 35 46 23 28 B/ B/ B/ D /E 50 65 40 B/ B B / D NOTES 1. Be sure polarity. Positive (+) side has white belt. 2. For cleaning, freon TE, TES and TMS are recommended at a temperature less than 50 for a period less than 5 minutes. 3. When ultrasonic cleaning is necessary, fixing capacitor body by epoxy adhesive before soldering is recommended. Establish adequate cleaning conditions by experiment to avoid damaging capacitor terminations. 4. Limit reverse voltage to V or less than 5% of rated voltage whichever is smaller. 5. In case of low impedance circuit use (Less than 3 Ω/V), adequate voltage derating is recommended to improve M.T.B.F. 6. In case of automatic mounting, the tweezer pressure shall be less than 500 grams and should not exceed 5 seconds.
MX ESR (Ω) @ 0kHz, +25 / BY VLUE ND SE SIZE MX RIPPLE URRENT (rms) @ 0kHz, +25 / BY VLUE ND SE SIZE VW (V) VW (V) 4.0 6.3 16 20 25 35 50 4.0 6.3 16 20 25 35 50 P (µf) P (µf) 0.1 24.0.0 0.1 0.054 0.056 0.15 2 20.0 0.15 0.058 0.059 B 17.0 B0.069 0. 18.0 B 14.0 0. 0.062 B0.076 0. 15.0 B 12.0 0. 0.068 B0.076 B0.082 14.0 12.0 B.0 0.071 0.076 B0.089 0.47 B.0 8.0 0.47 B0.089 0.117 0.68 12.0.0 9.0 7.5 B 8.0 0.68 0.076 0.084 0.088 0.121 B0.0 1.0 9.0 B 6.5 5.5 B 7.0 0.080 0.084 0.088 B0.111 0.141 B0.7.0 8.0 7.5 B 5.5 B 5.2 4.0 4.5 0.084 0.094 0.097 B0.121 B0.124 0.166 0.156 9.0 7.5 7.0 B 5.0 B 4.5 3.5 B 5.5 3.5 D 2.5 0.088 0.097 B0.0 B0.126 B0.1 0.177 B0.121 0.177 D0.249 3.3 9.0 7.5 6.5 6.2 B 3.8 B 3.6 2.5 D 2.0 3.3 0.088 0.097 0.4 0.6 B0.145 B0.149 0.2 D0.274 B 4.4 2.8 B0.135 0.198 4.7 7.5 6.5 6.0 B 3.6 B 3.5 D 1.4 B 4.0 2.8 D 4.7 0.097 0.4 0.8 B0.149 B0.151 0.214 0.4 D0.327 B0.141 0.198 D 0.316 6.8 6.5 6.0 B 3.5 B 3.3 2.0 D 1.3 E 1.2 B 4.0 2.6 D 1.4 6.8 0.4 0.8 B0.151 B0.156 0.214 0.235 D0.340 E0.371 B0.141 0.206 D0.327 6.0 B 3.5 B 3.2 B 2.0 1.8 D 0.8 B 4.0 2.5 D 1.3 D 1.2 B0.151 B0.158 B 0.183 0.235 0.247 D0.387 B0.141 0.2 0.4 D0.340 D0.354 15 B 3.5 B 3.2 B 1.8 1.7 D E 0.8 2.5 D 1.1 15 B0.151 B0.158 B0.183 0.247 0.254 D0.387 E0.454 0.2 0.4 D0.369 B 3.2 B B 2.5 B 2.3 D 0.8 E 0.7 2.5 1.8 D 0.9 B0.158 B0.183 BO.208 B0.35 O.277 D0.4 E0.486 1.6 0.262 D 1.1 0.2 0.4 0.247 D0.369 D0.408 B B 2.0 1.6 1.2 D 0.8 E 0.7 1.8 D 1.1 D 0.9 B0.183 BO.208 0.262 O.277 D0.4 E0.486 0.4 0.247 D0.369 D0.408 47 1.8 1.6 1.6 D 0.8 D 0.7 E 0.9 D 1.1 D 0.9 E 0.9 47 0.247 0.262 O.277 D0.4 D0.486 EO.524 D0.369 D0.408 EO.454 68 1.6 D 0.9 D 0.8 D 0.7 E 0.6 D 1.1 E 0.8 68 0.262 D0.408 D0.4 D0.463 E0.486 D0.369 E0.454 0 D 0.9 D 0.8 D 0.7 D 0.7 E 0.7 E 0.7 0 D0.408 D0.8 D0.462 DO.463 E0.486 E0.486 150 D 0.7 D 0.6 D 0.8 E 0.6 E 0.6 150 D0.463 DO.486 DO.524 E0.524 E0.524 0 E 0.6 D 0.7 D0.9 0 E0.524 E0.524 E0.524 E 0.6 E 0.6 D0.486 D0.524 Dimensions in mm EI ase ode (3216) B(3528) (6032) D(7343 E(7343H) L 3.2 3.5 6.0 7.3 7.3 W 1.6 2.8 3.2 4.3 4.3 H 1.7 1.9 2.5 2.9 4.0 P ±0.3 0.8 0.8 1.3 1.3 1.3 a 1.2 h(min) 0.7 0.7 34
HRTERISTI DT & URVES Frequency Dependence of the Permissible Superimposed Voltage Effect of ircuit Impedance on the Failure Rate LOD LIFE HRTERISTI URVES () Effect of the pplied Voltage and mbient Temperature on the Failure Rate TEMPERTURE HRTERISTI URVES () Immersion Method Reflow Method 35
TPING SPEIFITIONS Dimensions in mm Embossed Plastic Tape per EI-481-1 EI SIZE 3216 3528 6032 7343 7343H SE ODE B D E o 1.9 3.1 3.9 4.7 4.7 B o 3.9 3.9 6.3 7.7 7.7 W 8.0±.30 8.0±.30 12.0±.30 12.0±.30 12.0±.30 F 3.5±.05 3.5±0.5 5.5±.05 5.5±.05 5.5±.05 P 4.0 4.0 8.0 8.0 8.0 D 1 B 1 4.2 4.2 8.2 8.2 8.2 KMX 4.5 4.5 4.5 TPE SIZE 8mm 8mm 12mm 12mm 12mm QUNTITY PER REEL 7 REEL 13 REEL 2000 9000 2000 8000 500 3000 500 2500 500 2500 STNDRD ORIENTTION Standard reel diameter is 7 and 13 reels are available on special order with (13) added to the end of the part number. over tape peel-off specification 1. Peel-off speed: 300 mm/min. 2. Peel-off force: F = 30-75g 3. Peel-off angle: Θ = 0-15 36