195 ishay prague olid Tantalum hip apacitors TNTMOUNT onformal oated TU Qualified, 3001/00/00 - T2 mm, 12mm Tape Packaging to I-1-1 reeling per I 2-3. 7 (17mm) standard 13 (0mm) available U and uropean case sizes available POMN TITI Operating Temperature: - 55 to + 5. (To + 125 with voltage derating.) apacitance ange: 0.01µ to 0 µ apacitance Tolerance: ± %, ± 20 % standard oltage ating: 2W to 50 W. OIN INOMTION 195 TP PITN 0 PITN TOLN 00 OLT TIN T + 5 O 2 TMINTION T PKIN This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. 0 = ± 20% 9 = ± % This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. decimal point is indicated by an "" (3 =.3 volts). ee atings and ase odes Table. tyle 2 is standard 2 = olderable oating = old Plated = older Plated (0/0) pecial Order. Note: Preferred Tolerance and reel sizes are in bold. We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. oltage substitutions will be marked with the higher voltage rating. T = Tape and eel: 7" [17] eel standard 1/2 eel minimum 13" [0] eel available excluding the "" case, on request. ee Tape and eel pecifications. IMNION in inches [millimeters] W Tantalum Wire Nib Identifies node (+) Terminal L J J I O I L (max.) W (ef.) J (max.) N / 0.07 0.05 ± 0.0 0.05 ± 0.0 0.01 ± 0.00 0.02 ± 0.0 0.03 0.00 [1] [1.1 ± 0.25] [1.1 ± 0.25] [0.0 ± 0.20] [7 ± 0.25] [] [0.] 7257 0.23 0.235 ± 0.013 0.13 ± 0.0 0.051 ± 0.013 0.10 ±0.025 0.23 0.00 [7.2] [.0 ± 0.3] [3. ± 0.3] [1.3 ± 0.3] [. ± 0.] [.20] [0.] 351 0.13 0.072 ± 0.00 0.0 ± 0.00 0.023 ± 0.0 0.05 ± 0.0 0.1 0.00 [] [1.3 ± 0.20] [1. ± 0.20] [ ± 0.25] [2.1 ± 0.37] [2.90] [0.] 3527 0.13 0. ± 0.0 0.051 ± 0.0 0.023 ± 0.0 0.05 ± 0.0 0.1 0.00 [] [2.00 ± 0.25] [1.30 ± 0.25] [ ± 0.25] [2.1 ± 0.37] [2.90] [0.] 77 0.25 0. ± 0.0 0.051 ± 0.0 0.00 ± 0.020 0.200 ± 0.027 0.23 0.00 [7.2] [2.5 ± 0.25] [1.30 ± 0.25] [0 ± 0] [5.0 ± 0.9] [.20] [0.] 77 0.25 0. ± 0.0 0.09 ± 0.0 0.00 ± 0.020 0.200 ± 0.027 0.23 0.00 [7.2] [2.5 ± 0.25] [1.75 ± 0.25] [0 ± 0] [5.0 ± 0.9] [.20] [0.] 77 0.25 0. ± 0.0 0. ± 0.0 0.00 ± 0.020 0.200 ± 0.023 0.23 0.00 [7.2] [2.5 ± 0.25] [2.5 ± 0.25] [0 ± 0] [5.0 ± 9] [.20] [0.] Note: The anode termination ( less ) will be a minimum of 0.0 (0.25), ase = 0.005 (0.131) minimum 9 ocument Number 0001 evision 27-ug-02
195 ishay prague TIN N O µ.3 1 20 25 35 50 0. 0. 0. 0. 0.7 0..7. 7 0 120 0 10 0 0 TN TIN Max. L PITN @ + 25 (µ) O PT NUM* (µ) W @ + 5, U = 5... 2.7 W @ + 125, U = 3..7. 7 0 120 0 10 0 0.7. 7 0 120 0 10 0 1955_002T 19575_002T 1955_002T 195_002T 195_002T 195_002T 195_002T 1957_002T 195_002T 1957_002T 195127_002T 1957_002T 19517_002T 1957_002T 1957_002T 0. 0.9 1.3 1.9 2.7.0..0 7.2. 13.2.3 W @ + 5, U =... W @ + 125, U = 5 or % tolerance, specify "9"; for 20% tolerance, change to 0. 1955_32T 1955_32T 19575_32T 1955_32T 195_32T 195_32T 195_32T 195_32T 1957_32T 195_32T 1957_32T 195127_32T 1957_32T 19517_32T 1957_32T 0. 0.9 1.3 2.0 2..1.0 7.2 9.0. 13.2 Max. @ + 25, 120 z (%) ocument Number 0001 evision 27-ug-02 95
195 ishay prague TN TIN PITN (µ).7. 7 0 120 0.7. 7 0..7. 7 0.7 0..7. O PT NUM* W @ + 5, U = 13... 7 W @ + 125, U = 9 1 W @ + 5, U = 20... W @ + 125, U = 12 20 W @ + 5, U = 2... 13 W @ + 125, U = 1 25 W @ + 5, U = 32... 17 W @ + 125, U = 20 or % tolerance, specify "9"; for 20% tolerance, change to 0. 1955_02T 1955_02T 1955_02T 19575_02T 1955_02T 195_02T 195_02T 195_02T 195_02T 1957_02T 195_02T 1957_02T 195127_02T 1957_02T 1955_012T 1955_012T 1955_012T 1955_012T 19575_012T 1955_012T 195_012T 195_012T 195_012T 195_012T 1957_012T 195_012T 195_0202T 1955_0202T 1955_0202T 1955_0202T 1955_0202T 19575_0202T 1955_0202T 195_0202T 195_0202T 195_0202T 195_0202T 1957_0202T 1957_0252T 195_0252T 1955_0252T 1955_0252T 1955_0252T 1955_0252T 19575_0252T 1955_0252T 195_0252T 195_0252T 195_0252T 195_0252T Max. L @ + 25 (µ) 0.7 3.0.7..0 12.0.0 0.7 2.3 5.0 7.1.2 0.7 0.9 1. 2.0 3.0.. 9. 0. 0. 1.2 1.7 2.5 3. 5.5.3 Max. @ + 25 120 z (%) 9 ocument Number 0001 evision 27-ug-02
195 ishay prague TN TIN PITN (µ) 0. 0.7 0..7. 0. 0. 0. 0. 0.7 0..7. O 35 W @ + 5, U =... 23 W @ + 125, U = 2 0. 1.2 1. 2. 3.5 5.3 7.7 50 W @ + 5, U = 5... W @ + 125, U = 3 or % tolerance, specify "9"; for 20% tolerance, change to 0. PT NUM* 195_0352T 1957_0352T 195_0352T 1955_0352T 1955_0352T 1955_0352T 1955_0352T 19575_0352T 1955_0352T 195_0352T 195_0352T 195_0352T 195_0502T 195_0502T 195_0502T 195_0502T 1957_0502T 195_0502T 1955_0502T 1955_0502T 1955_0502T 1955_0502T 19575_0502T 1955_0502T 195_0502T Max. L @ + 25 (µ) 0. 1.1 1.7 2. 3. 5.0 Max. @ + 25 120 z (%) TPIL U @ + 25, IMPN N QUN "" ase "" ase 0 IMPN 0 IMPN 1µ - 35.7µ - 50 OM 1.7µ - OM 1 µ - 0.1 1K K 0K 1M M 0M QUN IN T 0.1 1K K 0K 1M M 0M QUN IN T ocument Number 0001 evision 27-ug-02 97
195 ishay prague TPIL U @ + 25, IMPN N QUN "" ase "" ase 00 0 IMPN IMPN 0 OM 1.µ - 20 OM 1 µ - 0.1 µ - 1 0.1 7µ -.3 0.01 0 1K K 0K 1M M QUN IN T 0.01 0 1K K 0K 1M M QUN IN T "" ase 0 IMPN.7µ - 50 OM 1 0.1 0µ -.3 0.01 0 1K K 0K 1M M QUN IN T 9 ocument Number 0001 evision 27-ug-02
195 ishay prague OIN INOMTION - UOPN U ONL 195 TP PITN 0 PITN TOLN 00 OLT TIN T + 5 O 2 TMINTION T PKIN This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. 0 = ± 20% 9 = ± % This is expressed in volts. To complete the threedigit block, zeros precede the voltage rating. decimal point is indicated by an "" (3 =.3 volts). ee atings and ase odes Table. tyle 2 is standard 2 = olderable oating = old Plated = older Plated (0/0) pecial Order. Note: Preferred Tolerance and reel sizes are in bold. We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. oltage substitutions will be marked with the higher voltage rating. T = Tape and eel: 10mm eel tandard = Tape and eel 10mm eel for case size, lengthwise, ee Tape and eel pecifications. IMNION in millimeters W Tantalum Wire Nib Identifies node (+) Terminal L J J O L ± 0.3 W ± 0.3 (max) ± 0.3 ± 0.3 (min) 2.* 1. 0.7 1. 0.3.2* 1. 1. 0. 2.5 0.3.2* 2.1 1. 0. 2.5 5.5 2.1 1.7 3.2 0. 5.0 2.0 3. 0. 7.0 2. 2..5 0. 7. 3.7 3.0 5.0 0. * ± 0.2mm Note: The anode termination ( less ) will be a minimum of 0.0 (0.25), ase = 0.005 (0.131) minimum ocument Number 0001 evision 27-ug-02 99
195 ishay prague 195 / T2 TN N, TIN N O 0. 0. 0. 0. 0.7 0..7. 7 0 µ 2.3 / 1 20 25 * NOT: 2,, 20 and 35 olt are not T2 ratings 35 / 0 50 TN TIN PITN (µ) Max. L @ + 25 (µ).3 W @ + 5, U =... W @ + 125, U = 5 Max. @ + 25 120 z (%) O PT NUM 2 W @ + 5, U = 2.... 1.2 W @ + 125, U = 1. 1955_00T.7 19575_00T. 1955_00T 195_00T 0. W @ + 5, U = 5... 2.7 W @ + 125, U = 3. 1955_002T.7 19575_002T 195_002T 195_002T 0. 195_002T 1.3 195_002T 2.7 0 1957_002.0 1955_32T 1955_32T. 1955_32T 195_32T 0. 195_32T 1.3 7 1957_32T 2. 195_32.1 W @ + 5, U = 13... 7 W @ + 125, U = 9.7. 7 or % tolerance, specify "9"; for 20% tolerance, change to "0". 1955_02T 1955_02T 19575_02T 1955_02T 195_02T 195_02T 1957_02 0.7.7 0 ocument Number 0001 evision 27-ug-02
195 ishay prague TN TIN PITN (µ) O PT NUM Max. L @ + 25 (µ) /1 W @ + 5, U = 20... W @ + 125, U = 12 20 W @ + 5, U = 2... 13 W @ + 125, U = 1 25 W @ + 5, U = 32... 17 W @ + 125, U = 20 Max. @ + 25 120 z (%) 0.7 1957_02T 0. 195_02T 1955_02T 1955_02T 1955_02T.7 19575_02T 0.7 195_02T 195_02T 195_02 5.0 0.7 1957_0202T 1955_0202T 1955_0202T 1955_0202T 0.7. 1955_0202T 1. 195_0202T 3.0 195_0202. 0. 195_0252T 0. 195_0252T 1955_0252T 1955_0252T 0..7 19575_0252T 1.2. 1955_0252T 1.7 195_0252T 2.5 195_0252 3. 35/0 W @ + 5, U = / 52... 23 / 25 W @ + 125, U = 2 / 30 0. 195_0352T 0. 195_0352T 0. 195_0352T 0. 195_0352T 0.7 1957_0352T 0. 195_0352T 1955_0352T 1955_0352T 1955_0352T 0. 1955_0352T 1.2.7 19575_0352T 1.. 1955_0252 2. 50 W @ + 5, U = 5... W @ + 125, U = 3 0. 195_0502T 0. 195_0502T 0. 195_0502T 0. 195_0502T 0.7 1957_0502T 0. 195_0502T 1955_0502T 1955_0502T 0. 1955_0502T 1.1 1955_0502T 1.7.7 19575_0502 2. or % tolerance, specify "9"; for 20% tolerance, change to "0". ocument Number 0001 evision 27-ug-02 1
195 ishay prague POMN TITI uropean Product ase sizes to comply to : 3001/00/00 - T2 1. Operating Temperature: apacitors are designed to operate over the temperature range of - 55 to +5. 1.1 apacitors may be operated to + 125 with voltage derating to two-thirds the + 5 rating. Working oltage () 2.3 /1 20 25 35 0 50 + 5 ating + 125 ating urge oltage () 2. 5 13 20 2 32 52 5 Working oltage () 1.2 2.7 7 13 17 23 25 urge oltage () 1. 3. 5 9 12 1 20 2 30 3 2. Working oltage: The working voltage is the maximum operating voltage for continuous duty at the rated temperature. 3. urge oltage: The surge rating is the maximum voltage to which the capacitors may be subjected under any conditions, including transients and peak ripple at the highest line voltage. 5. apacitance hange With Temperature: The capacitance change with temperature shall not exceed the following percentage of the capacitance measured at + 25 : 7. Leakage urrent: apacitors shall be stabilized at the rated temperature for 30 minutes. ated voltage shall be applied to capacitors for 5 minutes using a steady source of power (such as a regulated power supply) with a 00 ohm resistor connected in series with the capacitor under test to limit the charging current. Leakage current shall then be measured. Note that the leakage current varies with temperature and applied voltage. ee graph below for the appropriate adjustment factor. TPIL LK UNT TO N 0-55 - % + 5 + % + 125 + 12%. issipation actor: The dissipation factor, determined from the expression 2πf, shall not exceed values listed in the tandard atings Table..1 Measurements shall be made by the bridge method at, or referred to, a frequency of 120 z and a temperature of + 25. 3.1 urge oltage Test: apacitors rated up to 35 volts at +5 shall withstand the surge voltage applied in series with a ohm ± 5% resistor at the rate of onehalf minute on, one-half minute off, at + 5, for 00 successive test cycles. apacitors rated 50 volts at +5 require a series resistance of 00 ohms. + 125 + 5 + 55 3.2 ollowing the surge voltage test, the dissipation factor and the leakage current shall meet the initial requirements; the capacitance shall not have changed more than ± 5%.. apacitance Tolerance: The capacitance of all capacitors shall be within the specified tolerance limits of the nominal rating. Leakage urrent actor 0.1 + 25 0-55.1 apacitance measurements shall be made by means of polarized capacitance bridge. The polarizing voltage shall be of such magnitude that there shall be no reversal of polarity due to the component. The maximum voltage applied to capacitors during measurement shall be 2 volts rms at 120 z at + 25. If the voltage applied is less than one-half volt rms, no bias is required. ccuracy of the bridge shall be within ± 2%. 0.01 0.001 0 20 30 0 50 0 70 0 90 0 Percent of ated oltage 2 ocument Number 0001 evision 27-ug-02
195 ishay prague POMN TITI (ontinued) 7.1 t + 25, the leakage current shall not exceed the value listed in the tandard atings Table. 7.2 t + 5, the leakage current shall not exceed times the value listed in the tandard atings Table. 7.3 t + 125, the leakage current shall not exceed 12 times the value listed in the tandard atings Table.. Life Test: apacitors shall withstand rated voltage applied at + 5 or two-thirds rated voltage applied at + 125 for 2000 hours..1 ollowing the life test, the dissipation factor and leakage current shall meet the initial requirements; the capacitance change shall not exceed ± %. 9. helf Life : apacitors shall withstand a shelf test for 5000 hours at a temperature of +5 with no voltage applied. 9.1 ollowing the shelf life test, the leakage current shall meet the initial requirement; the dissipation factor shall not exceed 0% of the intial requirement; the capacitance change shall not exceed ± 5%. Moisture esistance:.1 apacitors shall be subjected to temperature cycling at 90% to 95% relative humidity, from + 25 to + 5 to + 25 (+, - 2 ) over a period of hours per cycle for 00 hours..2 ollowing the moisture resistance test, the leakage current and dissipation factor shall meet the initial requirements, and the change in capacitance shall not exceed ± %. 11. umidity Test: 11.1 apacitors shall withstand exposure to 90% to 95% relative humidity at full rated voltage at +0 for 00 hours. 11.2 ollowing the humidity test, the leakage current shall not exceed 200% of the initial requirement; the dissipation factor shall not exceed 0% of the initial requirement; the change in capacitance shall not exceed ± 12% 12. Thermal hock: 12.1 apacitors shall be conditioned prior to temperature cycling for minutes at + 25, at less than 50% relative humidity and a barometric pressure at 2 to 31 inches. 1 apacitors shall be subjected to thermal shock in a cycle of exposure to ambient air at - 55 (+ 0, - 5 ) for 30 minutes, then + 25 (+, - 5 ) for 5 minutes, then + 125 (+ 3, - 0 ) for 30 minutes, then + 25 (+, - 5 ) for 5 minutes for 5 cycles. 12.3 apacitors shall show no evidence of harmful or extensive corrosion, obliteration of marking or other visible damage. 12. ollowing the thermal shock test, capacitors shall meet the original requirements for leakage current and dissipation factor, capacitance change shall not exceed ± 5% of the original measured value. 13. oldering ompatibility: 13.1 older ip: apacitors will withstand two cycles of a dip in non-activated rosin flux, followed by full immersion in 0/0 tin lead solder for 5 seconds at + 25. 13.1.1 apacitance: leakage and dissipation factor shall remain within the initial requirements. 13.1.2 There shall be no evidence of dewetting or termination leaching. Wetting must occur on at least 95% of the metallized surface (per MIL--5535). 13.2 older eat: apacitors will withstand exposure to + 20 + 5 for seconds. 1 olderability: apacitors will meet the solderability requirements of (MIL--5535) 1. Marking: The small body area of these capacitors does not permit elaborate marking schemes. equired information will be distinctly marked on the carton or packages in which the units are shipped.. Polarity: The anode terminal of each capacitor is identified by wire nib (see dimensional configurations). ocument Number 0001 evision 27-ug-02 3
195 ishay prague UI TO PPLITION 1. - ipple urrent: The maximum allowable ripple current shall be determined from the formula: where, P I rms = P = Power issipation in Watts @ + 25 as given in the table in Paragraph Number 5 (Power issipation). = The capacitor quivalent eries esistance at the specified frequency. 1.1 Non-sinusoidal ripple current may produce heating effects that differ from those produced by sinusoidal ripple current. It is important that the Irms value be established when calculating permitted operating levels. 1.2 Permissible power dissipation as shown in Paragraph Number 5 (Power issipation) has been determined for a maximum chip temperature rise of 25 above ambient temperature (T ) with the chip supported in air by lead attachments. ecause the effectiveness of heat sinking varies widely with ambient conditions and thermal management, criteria may be unnecessarily conservative. It is recommended that thermocouple measurements of actual chip temperature be made under operating condition. In no case should the chip temperature rise above + 5 at rated voltage. 2. - ipple oltage: The maximum allowable ripple voltage shall be determined from the formula: rms = or, from the formula: rms = I rms x where, P = Power issipation in Watts @ + 25 as given in the table in Paragraph Number 5 (Power issipation). = The capacitor quivalent eries esistance at the specified frequency. P = The capacitor Impedance at the specified frequency. 2.1 The sum of the peak voltage plus the voltage shall not exceed the voltage rating of the capacitor. The sum of the negative peak voltage plus the applied voltage shall not allow a voltage reversal exceeding % of the working voltage at + 25. 3. everse oltage: These capacitors are capable of withstanding peak voltages in the reverse direction equal to % of the rating at + 25 and 5% of the rating at + 5.. Temperature erating: If these capacitors are to be operated at temperatures above + 25, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown: Temperature erating actor + 25 + 55 0.9 + 5 0. + 125 0. 5. Power issipation: Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may produce heating effects which differ from those shown. It is important that the equivalent Irms value be established when calculating permissible operating levels. Maximum Permissible Power ase issipation @ +25 (watts) ode in ree ir 0.030 0.250 0.00 0.095 0.1 0.120 0.135 Maximum Permissible Power ase issipation @ +25 (watts) ode in ree ir 0.0 0.05 0.0 0.090 0.11 0.12 0.1 ocument Number 0001 evision 27-ug-02
195 ishay prague UI TO PPLITION (ontinued). Printed ircuit oard Materials: The capacitors are compatible with most commonly used printed circuit board materials (alumina substrates,, 5,, PT-fluorocarbon and porcelanized steel). If your desired board material is not shown there please contact the Tantalum Marketing epartment for assistance in determining compatibility. 7. ttachment: 7.1 older Paste: The recommended thickness of the solder paste after application is 0.007" ±.001" [.17mm ±.025mm]. are should be exercised in selecting the solder paste. The metal purity should be as high as practical. The flux (in the paste) must be active enough to remove the oxides formed on the metallization prior to the exposure to soldering heat. 7.2 oldering: apacitors can be attached by conventional soldering techniques - convection, infrared reflow, wave soldering and hot plate methods. The oldering Profile chart shows typical recomended time/temperature conditions for soldering. ttachment with a soldering iron is not recommended due to the difficulty of controlling temperature and time at temperature. The soldering iron must never come in contact with the capacitor. 7.3 onductive poxy: It is recommended that the epoxy cure cycle shall not exceed + 0 for sixty minutes. 9. ecommended Mounting Pad eometries: The nib must have sufficient clearance to avoid electrical contact with other components. The width dimension indicated is the same as the maximum width of the capacitor. This is to minimize lateral movement. MTLLITION N OL PT K INIT OL PT in inches [millimeters] P NO NI MTLLITION PTION LLOWN WIT O 0.025 [.35] 0. [3.55] 0.025 [.35] 0.055 [] 0.05 [] 0.113 [2.7] 0.02 [7] 0.25 [.] 0.00 [2] 0.00 [2] 0.0 [.31] 0.00 [2.03] 0.00 [2] 0.00 [2] 0.0 [.31] 0.11 [2.90] 0.05 [] 0.113 [2.7] 0.02 [7] 0.11 [2.90] 0.05 [] 0.113 [2.7] 0.02 [7] 0.11 [2.90] 0.05 [] 0.113 [2.7] 0.02 [7] 0.11 [2.90]. leaning (lux emoval) after oldering : The 195 is compatible with all commonly used solvents, such as T, TM, Prelate and hlorethane. olvents containing methylene chloride or other epoxy solvents should be avoided since these will attack the epoxy encapsulation material. MTLLITION N OL PT K INIT OL PT OMMN LOW OLIN POIL TMPTU. NTI 250 200 0 0 50 0 50 0 0 200 250 300 350 TIM (ON) Note: In millimeters P NO NI MTLLITION PTION LLOWN WIT O 1.1 0. 0.3 1.7 1.2 1.2 0. 1. 1. 1.2 0. 2.3 1. 1. 1.1 2.3 1. 1.2 3.5 1. 3.2 1.2 2. 1. 3. 1. 3.9 ocument Number 0001 evision 27-ug-02 5
195 ishay prague TP N L PKIN in inches [millimetres] tandard orientation is with the cathode (-) nearest to the sprocket holes per I-1-1 and I 2-3. Top over Tape Thickness arrier mbossment Min. ending adius (Note 1) Notes: 1. 12mm embossed tape with components shall pass around radius "" without damage. The minimum trailer length may require additional length to provide minimum for reels with hub diameters approaching N minimum. 2. or,, cases, mm pitch; for case, mm pitch. Minimum: mm 1/2 Pitch and mm = 0.9" [25] 12mm, 12mm ouble Pitch = 1.11" [30]. ase Tape omponent Units Per eel ode Width Pitch 7 [17] eel 13 [0] eel mm mm 2500,000 12mm mm 00 - mm mm 2500,000 mm mm 2500,000 12mm mm 2000,000 12mm mm 00 7,500 12mm mm 00 5,000 ase Tape omponent Units Per eel ode Width Pitch 10 mm eel Taping ode mm mm 2500 T 12mm mm 2000 T 12mm mm 2000 T 12mm mm 2000 T 12mm mm 700 T 12mm mm 0 T 12mm 12mm 00 * * Not available for other case sizes ocument Number 0001 evision 27-ug-02
195 ishay prague TP N L PKIN in inches [millimeters] 0.02 [0.00] Max. T 2 Max. eformation etween mbossments 0.059 + 0.00-0.0 [ + 0. - 0.0] 0.7 ± 0.00 [.0 ± 0.] Pitches umulative Tolerance on Tape ± 0.00 [0.200] P 1 mbossment 0.09 ± 0.00 [1.75 ± 0.] 1 (Note 5) K 0 Top over Tape 0 0 0.030 [0.75] Min. (Note 2) 0.030 [0.75] Min. (Note 3) W or Tape eeded eference only including draft. oncentric around 0 (Note ) 1 0.00 [0.] Max. enter Lines of avity P 1 ITION O Maximum avity ize (Note 1) 1 Min. omponents 0.079 x 0.07 [2.0 x 1.2] and Larger. (Note ) athode (-) node (+) ITION O Note: Metric dimensions will govern. imensions in inches are rounded and for reference only. TP I 1 (Max.) (Note 5) 1 (Min.) (Note ) (Min.) P 1 P 2 1 (Min.) T 2 (Max.) W 0 0 K 0 mm 0.179 [.55] 0.039 [] 0.13 ± 0.002 [3.5 ± 0.05] 0.7 ± 0.00 [.0 ± 0.1] 0.079 ± 0.002 [2.0 ± 0.05] 0.09 [2.5] 0.3 + 0.012-0.00 [.0 + 0.3-0.1] 12mm 0.323 [.2] 0.059 [] 0.217 ± 0.002 [5.5 ± 0.05] 0.7 ± 0.00 [.0 ± 0.1] 0.079 ± 0.002 [2.0 ± 0.05] 0.25 [.5] 0.72 ± 0.012 [12.0 ± 0.30] (Note 1) 12mm ouble Pitch 0.323 [.2] 0.059 [] 0.217 ± 0.002 [5.5 ± 0.05] 0.3 ± 0.00 [.0 ± 0.1] 0.079 ± 0.002 [2.0 ± 0.05] 0.25 [.5] 0.72 ± 0.012 [12.0 ± 0.30] Notes: 1. 0 0 K 0 are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the cavity ( 0 0 K 0 ) must be within.002" [0.05] minimum and.020" [0] maximum and the clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees. 2. This dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the cavity whichever is less. 3. This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less.. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. imensions of embossment location and hole location shall be applied independent of each other. 5. 1 dimension is a reference dimension for tape feeder clearance only. ocument Number 0001 evision 27-ug-02 7