ChE 344 Winter 011 Mid Term Exam I + Thursday, February 17, 011 Closed Book, Web, and Notes Name Honor Code (sign at the end of exam) 1) / 5 pts ) / 5 pts 3) / 5 pts 4) / 15 pts 5) / 5 pts 6) / 5 pts 7) / 0 pts 8) / 0 pts 9) / 0 pts Total /100 pts I have a Laptop with Polymath on it that I can bring to the nd Mierm Exam. I will need to use the computer lab for the nd Mierm Exam.
(5 pts) 1) Mole Balances, Chapter 1 The reaction A + B C takes place in an unsteady PFR. The feed is only A and B in equimolar proportions. Which of the following set of equations gives the correct mole balances on A, B and C. Species A and B are disappearing and Species C is being formed. Circle the correct answer where all the mole balances are correct (a) F A0 F A r A d = dn A F B0 F B r A d = dn C Wrong sign for r A, should be + r A d (b) F C + F A0 F A + 0 r A d = dn C r A d = dn A F B0 F B + r A d = dn B Wrong sign for F C, should be F C (c) F C + F A0 F A + r C d = dn C r A d = dn A F B0 F B + r A d = dn B All are correct. (d) F C F A0 F A r A d = dn C r A d = dn A F B0 F B r A d = dn B Wrong sign for r A, should be + r A d F C + r C d = dn C Answer is (c).
(5 pts) ) Sizing, Chapter For the gas phase reaction A + B C equimolar amounts of A and B are to be fed, i.e., y A0 = 0.5 and δ 0. The following the Levenspiel plot was constructed for a temperature of T = 318K and entering pressure of P 0 = 10 atm. 4 F A0 r A ( m 3 ) 3 1 Note: δ 0 0. 0.4 0.6 0.8 (a) What reactor type and size would you use to achieve 40% conversion? Reactor Type olume (b) What reactor type and size would you use to achieve 60% conversion? Reactor Type olume (c) What reactor type and size would you use to achieve 0% conversion? Reactor Type olume (d) What reactor type and size would you use to increase the conversion from 60% to 80%? Reactor Type olume Note: If more than one reactor type would work for any part (a d), explain. X
(5 pts) 3) Rates, Chapter 3 Determine the rate law for the reaction described in each of the cases below. The rate laws should be elementary as written for reactions that are of the form either A B or A + B C (a) The units of the specific reaction rate are k = dm3 mol h (b) The units of the specific reaction rate are mol k = dm 3 h (c) The units of the specific reaction rate are mol k = kg cat h atm (d) The units of the specific reaction rate are k = 1 h Law Law Law Law
(15 pts) 4) i>clickers Chapters 4 and 5 ( pts) 4a) Consider the gas-phase elementary reaction R S which takes place in a PFR in which R and inert I are fed. If the entering concentration of R is cut by a factor of 5 while maintaining a constant entering volumetric flow rate, υ 0, how will the conversion change? Circle the correct answer. A) X won t change B) X will increase C) X will decrease Explain B) X will increase dx d = r R = kc R0 1 X F R0 ( 1+ εx) F R0 ε = y R0 δ = y R0 ( 1) = y R0 dx d = kc R0 υ 0 C R0 1 y R0 then 1+ y R0 X dx d X ( 1 X) ( 1+ y A0 X) = k ( 1 X ) υ 0 1+ y R0 υ 0 = F T 0 RT 0 P 0 = F R0 + F I0 P 0 RT 0 F I0 as F A0 to keep υ 0 constant. (3 pts) 4b) The liquid phase reaction A + B 3C follows an elementary rate law and is carried out in a constant volume batch reactor with stoichiometric feed. For a batch reaction time of one hour the conversion is 50%. If the same reaction is carried out in a PFR at the same temperature in which there is no pressure drop, for the same space time of one hour would the conversion be
Circle the correct answer. A) X > 50% B) X < 50% C) X = 50% D) Insufficient information to answer definitively Explain C) X = 50% r A f P for liquid ( pts) 4c) For the isothermal, elementary gas-phase reaction X Z how does the PFR volume required for a given conversion change with increasing mole fraction, y X0, of X when the inlet concentration of X and inlet total volumetric flow rate remain constant? There is no pressure drop and only X and Inert I enter the reactor. Circle the correct answer. A) increases B) decreases C) No change in D) Insufficient information to answer definitively Explain B) decreases υ = υ 0 ( 1+ εx), δ = 1 1= 1 ε = y X0δ = y X0 r A = kc 1 X X, C X = C X0 1+ εx = F X0 k ( 1+ εx) 1 X dx, = υ0 C X0 kc X0 1 y X0 X ( 1 X) dx y X0 ( 1 y X0 X) also 1 C X0
( pts) 4d) If the following liquid-phase reaction is elementary and reversible, what is the rate expression in terms of conversion when equimolar amounts of A and B are fed to the reaction? A B Circle the correct answer. Explain C) r A = kc A0 1 X r A = k C A C B K C C A = C A0 ( 1 X) C B = ( Θ B + X) C B = ( 1+ X) r A = kc A0 1 X [ 1 X] A) r A = kc A0 K C X B) r A = kc A0 1 X [ ] 1+ X K C ( 1+ X) (3 pts) 4e) Consider the reaction K C C) r A = kc A0 1 X [ ] 1+ X [ ] D) r A = kc A0 1 X 1+ 1 A B If the diameter of a PBR is doubled while keeping the turbulent flow mass flow rate, m, constant, what can be said about that factor by which the rate of pressure drop (dy/dw) will be lowered? Circle the correct answer. A) It will be lowered by a factor of 4 B) It will be lowered by a factor of 16 C) It will be lowered by a factor of 3 D) It will be lowered by a factor of 48 or more Explain K C K C
D) It will be lowered by more than a factor of 48. G ~ m D, A C ~ πd α ~ G ~ 1 1 = 1 A C D 6 α = α D 1 D D 4 6 D 6 1 = α 1 = α 1 64 (3 pts) 4f) In a particular differential reactor experiment for the reaction A B the entering volumetric flow rate is doubled, leaving all other variables the same. How would you expect the measured outlet flow rate of B, to change under conditions of differential reactor conversion? Circle the correct answer. A) Molar flow rate of product will go up B) Molar flow rate of product will go down C) No Change Explain C) No Change F B = ΔW r B ʹ r B ʹ = r A ʹ r A ʹ r A0 F B = W( r A0 ʹ ) Not a function of υ 0.
(5 pts) 5) Membrane Reactors, Chapter 6 ( pts) 5a) Consider the gas phase reaction A B+ C On the figure below is a sketch the molar flow rates FA, FB, and FI for species A and B as a function of membrane volume. The dark lines, A and B, represent the base case while the lighter lines represents possible profiles when the mass transfer coefficient for B, k CB, is increased. Which figure correctly corresponds to an increase in the mass transfer coefficient k CB? Circle the correct answer. A) 1 B) C) 3 D) 4 A B (1) Increase kcb () F i A F i A B B (3) (4) F i A F i A B B Explain Ans. A) 1: B diffuses out faster moving the reaction faster to the right so both the concentrations of A and B are smaller.
As B is removed, the reaction will continue to proceed to the right. The rate at which it proceeds to the right depends upon the rate of removal of B. If kcb is small in the conversion will always increase but at a very slow rate. If B is removed very very rapidly, the reaction will behave as a irreversible reaction. On the figure below sketch the molar flow rates FA, FB, and FI as a function of IMRCF volume. (3 pts) 5b) Membrane Reactor 50% A and 50% I inerts A B+ C Both B and inerts I diffuse out. Which of the following figures has the greatest mass transfer coefficient for the inerts, kci for the rate of removal of inerts? All other constants remain the same. A B I Circle the correct answer. A) 1 B) Explain B) For large kci, I diffuses out of the membrane and as a result that the concentration of C A is increased for constant T and P. P C A = y 0 A, y I y A C A r A RT 0 Consequently the reaction rate will proceed more rapidly at the entrance to the reactor before approaching equilibrium at some point down the reactor.
(5 pts) 6) Analysis of Data, Chapter 7 ( pts) 6a) From the following plot, what is the reaction order with respect to A? Circle the correct answer. A) 0 B) 0.5 C) 0.78 D) 1 E) Explain D) 1 Slope =1.01 1 (3 pts) 6b) The following reaction, batch experiments are conducted to evaluate the reaction kinetics. The slope of a ln (r B) versus ln (C B) plot is measured to be 1.0 and the intercept is 0.4 when A is in great excess. What is the overall reaction order? Circle the correct answer. A + B Products A) 0.4 B) 1.0 C) 1.44 D) Can t tell on the basis of this experiment Explain
D) Can t tell on the basis of this experiment r A = r B = kc α AC β B = ln r B = ln k + α ln C A + β ln C B Both C A and C B vary, need to find α by varying C A
(0 pts) 7) Pressure Drop, Chapter 5 The gas phase reaction A + B C+ D is carried out isothermally at 7 C in a packed bed reactor with 100 kg of catalyst. The reaction is first order in A and first order in B. The entering pressure was 0 atm and the exit pressure is atm. The feed is equal molar in A and B and is in the flow in the turbulent regime with F A0 = 10 mol/min and C A0 = 0.44 mol/dm 3. Currently 80% conversion is achieved. Intra particle diffusion effects in the catalyst particles can be neglected. (a) What is the specific reaction rate? k = (b) What would be the conversion if the particle size were doubled and there are no internal mass transfer limitations? X = (a) dx dw = r A ʹ = kc A0 1 X F A0 y F A0 = kc A0 X 1 X = kc A0 W αw F A0 ( 1 X) 1 αw F A0 α = y = 0 = ( 1 αw)1 y = ( 1 αw) 1 y W 0.9 1 0.9 = k 0.44 10 = 1 0.01 100 α = 9.9 10 3 [ ] = 0.99 100 100 9.9 10 3 10 4 9 = k[ 0.059] [ 100 49.5] 10
k = ( 9 10) 50.5 ( 0.059) = 30. dm 3 mol min (b) For the turbulent flow α ~ 1 D P D α = α P1 1 = α 1 D P = 9.9 10 3 kg 1 = 4.95 10 3 kg 1 X 1 X = 30. ( 0.44) 10 100 4.95 10 3 100 = 0.18[ 100 4.7] = 13.5 X = 0.93
(0 pts) 8) Modified California Problem P5-0 B The elementary gas phase reaction A + B C + D takes place isobarically and isothermally in a PFR where 50% conversion is achieved. The feed is equimolar in A and B. It is proposed to put a CSTR of equal volume upstream, i.e., of the PFR. What will be the intermediate and exit conversions X 1 and X respectively? The entering flow rates and all other variables remain the same as that for the single PFR. X 1 = Case 1 X = Mole Balance dx d = r A Rate Law r A = kc A C B Stoichiometry Gas δ = 0, Θ B =1 C A = C A0 ( 1 X) C B = C A0 ( 1 X) Combine r A = kc A0 dx d = kc A0 F A0 ( 1 X) ( 1 X) dx ( 1 X) = kc A0 d F A0 = 0, X = 0 =, X = 0.5
X 0 dx ( 1 X) = X 1 X = kc A0 F A0 Case kc A0 = 0.5 F A0 1 0.5 =1 (1) CSTR = F A0X r A () & (3) Rate Law, Stoichiometry same as Case 1 CSTR = kc A0 kc A0 F A0 X 1 1 X 1 X 1 =1= F A0 1 X 1 + X 1 1 X 1 + X 1 = X 1 X 1 3X 1 +1= 0 X 1 = 3 ± 9 4 = 3 5 = 3.4 = 0.38 PFR X 1 = 0.38 dx d = kc A0 1 X, F A0 = 0 X = X 1 = 0.38 = X = X X X 1 dx ( 1 X) = kc A0 F A0 kc A0 =1= F A0 1 1 1 X 1 X 1 1 1 =1+ =1+ 1 1 X 1 X 1 0.6 =.6 1 X = 0.38 X = 0.6
(0 pts) 9) P5-9 B Study Problem on Syllabus. The gas phase reaction E = cal/mol P5-9 PFR dx d = r A = kc A0 1 X F A0 C A υ 0 1+ εx X ( 1+ εx) dx = 0 k 1 X = k ( 1 X ) υ 0 ( 1+ εx) d υ 0 = kτ k = 1 ( 1+ ε)ln 1 εx τ 1 X τ = 10dm 3 5dm 3 s = s ε = y A0 δ =11+1 1 =1 k = 1 ( 1+1 1 )ln 0.8 1 0.8 k = 1 [ 1.61 0.8]=1.09 at 300K CSTR = F A0 X r A = υ 0 C A0 X ( 1 X) 1+ εx kc A0 = υ 0X 1+ εx k 1 X
ε = 1 ( 1+1 1 ) k = 1 τ X 1+ εx ε = 0.5 ( 1 X) = 1 ( 0.8 1+ 0.5 0.8 0. =.8 ln k = E 1 1 k 1 R T 1 T ln.8 1.1 = E 1 R 300 1 = E 30 R E = R 300 ( 30) 0 ln.8 1.1 E = 8010 cal mol 0 ( 30) 300, R =1.987 cal mol K