TCMT11. Series Optocoupler, Phototransistor Output, Single Channel, Half Pitch Mini-Flat Package 22628-1 C E 4 3 1 2 DESCRIPTION The TCMT11. series consist of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 4 pin package. The elements are mounted on one leadframe providing a fixed distance between input and output for highest safety requirements. A C FEATURES Low profile package (half pitch) AC isolation test voltage 375 V RMS Low coupling capacitance of typical.3 pf Current transfer ratio (CTR) selected into groups Low temperature coefficient of CTR Wide ambient temperature range Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS Programmable logic controllers Modems Answering machines General applications AGENCY APPROVALS UL1577, file no. E76222, double protection cul component acceptance service no. 5A, double protection DIN EN 6747-5-5 (VDE 884-5) FIMKO: FI EN 695-1:26 BSI: BS EN665:22 BS EN695-1:26 CQC GB 8898-211, GB 4943.1-211 (suitable for installation altitude below 2 m) ORDERING INFORMATION T C M T 1 1 # SSOP-4 PART NUMBER 7.21 mm AGENCY CERTIFIED/ PACKAGE UL, cul, FIMKO, BSI, VDE SSOP-4 CTR (%) 5 ma 1 ma 5 ma 5 to 6 4 to 8 63 to 125 1 to 2 16 to 32 5 to 15 1 to 3 8 to 16 13 to 26 2 to 4 TCMT11 TCMT111 TCMT112 TCMT113 TCMT114 TCMT115 TCMT116 Notes Available only on tape and reel (1) Product is rotated 18 in tape and reel cavity TCMT117, TCMT117T3 (1) TCMT118 TCMT119 Rev. 3.1, 25-Jun-218 1 Document Number: 8351 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT11. Series ABSOLUTE MAXIMUM RATINGS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage V R 6 V Forward current 6 ma Forward surge current t p 1 μs SM 1.5 A Power dissipation P diss 1 mw Junction temperature T j 125 C OUTPUT Collector emitter voltage V CEO 7 V Emitter collector voltage V ECO 7 V Collector current I C 5 ma Collector peak current t p /T =.5, t p 1 ms I CM 1 ma Power dissipation P diss 15 mw Junction temperature T j 125 C COUPLER AC isolation test voltage (RMS) Related to standard climate 23/5 DIN 514 V ISO 375 V RMS Total power dissipation P tot 25 mw Operating ambient temperature range T amb -4 to +1 C Storage temperature range T stg -4 to +125 C Soldering temperature (1) T sld 26 C Notes Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability (1) Refer to reflow profile for soldering conditions for surface mounted devices. Also refer to Assembly Instructions (www.vishay.com/doc?854) ELECTRICAL CHARACTERISTICS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage = 5 ma V F - 1.35 1.6 V Junction capacitance V R =, f = 1 MHz C j - 8 pf OUTPUT Collector emitter voltage I C = 1 μa V CEO 7 - - V Emitter collector voltage I E = 1 μa V ECO 7 - - V Collector dark current V CE = 2 V, = A I CEO - - 1 na COUPLER Collector emitter saturation voltage = 1 ma, I C = 1 ma V CEsat - -.3 V Cut-off frequency V CE = 5 V, = 1 ma, R L = 1 Ω f c - 1 - khz Coupling capacitance f = 1 MHz C k -.3 - pf Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements Rev. 3.1, 25-Jun-218 2 Document Number: 8351 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT11. Series CURRENT TRANSFER RATIO (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT V CE = 5 V, = 5 ma TCMT11 CTR 5-6 % TCMT111 CTR 4-8 % V CE = 5 V, = 1 ma TCMT112 CTR 63-125 % TCMT113 CTR 1-2 % I C / TCMT114 CTR 16-32 % TCMT115 CTR 5-15 % TCMT116 CTR 1-3 % V CE = 5 V, = 5 ma TCMT117 CTR 8-16 % TCMT118 CTR 13-26 % TCMT119 CTR 2-4 % SWITCHING CHARACTERISTICS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Delay time V S = 5 V, I C = 2 ma, R L = 1 Ω, (see figure 1) t d - 4. - μs Rise time V S = 5 V, I C = 2 ma, R L = 1 Ω, (see figure 1) t r - 5.5 - μs Fall time V S = 5 V, I C = 2 ma, R L = 1 Ω, (see figure 1) t f - 7. - μs Storage time V S = 5 V, I C = 2 ma, R L = 1 Ω, (see figure 1) t s - 1.5 - μs Turn-on time V S = 5 V, I C = 2 ma, R L = 1 Ω, (see figure 1) t on - 9.5 - μs Turn-off time V S = 5 V, I C = 2 ma, R L = 1 Ω, (see figure 1) t off - 8.5 - μs Turn-on time V S = 5 V, = 1 ma, R L = 1 kω, (see figure 2) t on - 3. - μs Turn-off time V S = 5 V, = 1 ma, R L = 1 kω, (see figure 2) t off - 2. - μs + 5 V IC = 2 ma; adjusted through input amplitude I C t p t R G = 5 Ω t p T =.1 t p = 5 µs 5 Ω 1 Ω Channel I Channel II Oscilloscope R L = 1 MΩ C L = 2 pf 1 % 9 % 1 % t r t d t on t s t f t off t 95 184 Fig. 1 - Test Circuit, Non-Saturated Operation t p t d t r t on (= t d + t r ) Pulse duration Delay time Rise time Turn-on time t s t f t off (= t s + t f ) Storage time Fall time Turn-off time 96 11698 = 1 ma + 5 V I C Fig. 3 - Switching Times R G = 5 Ω t p T =.1 t p = 5 µs 5 Ω 1 kω Channel I Channel II Oscilloscope R L 1 MΩ 2 pf C L 95 1843 Fig. 2 - Test Circuit, Saturated Operation Rev. 3.1, 25-Jun-218 3 Document Number: 8351 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT11. Series SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Climatic classification According to IEC 68 part 1 4 / 11 / 21 Pollution degree According to DIN VDE 19 2 Comparative tracking index Insulation group IIIa CTI 175 Maximum rated withstanding isolation voltage According to UL1577, t = 1 min V ISO 375 V RMS Maximum transient isolation voltage According to DIN EN 6747-5-5 V IOTM 6 V peak Maximum repetitive peak isolation voltage According to DIN EN 6747-5-5 V IORM 77 V peak T amb = 25 C, V IO = 5 V 1 12 Isolation resistance T amb = 1 C, V IO = 5 V R IO 1 11 Ω T amb = T S, V IO = 5 V 1 9 Output safety power P SO 35 mw Input safety current I SI 15 ma Input safety temperature T S 175 C Creepage distance 5 mm Clearance distance 5 mm Insulation thickness DTI.4 mm Input to output test voltage, method B Input to output test voltage, method A V IORM x 1.875 = V PR, 1 % production test with t M = 1 s, partial discharge < 5 pc V IORM x 1.6 = V PR, 1 % sample test with t M = 1 s, partial discharge < 5 pc V PR 1326 V peak V PR 1132 V peak TYPICAL CHARACTERISTICS (T amb = 25 C, unless otherwise specified) P tot - Total Power Dissipation (mw) 3 Coupled device 25 2 Phototransistor 15 IR-diode 1 5 4 8 12 96 117 T amb - Ambient Temperature ( C) - Forward Current (ma) 1 1 1 T amb = 11 C T amb = 75 C T amb = 25 C T amb = C T amb = -55 C.1.6.8 1. 1.2 1.4 1.6 V F - Forward Voltage (V) Fig. 4 - Total Power Dissipation vs. Ambient Temperature Fig. 5 - Forward Voltage vs. Forward Current Rev. 3.1, 25-Jun-218 4 Document Number: 8351 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT11. Series I C - Collector Current (ma) 55 5 = 35 ma 45 4 = 3 ma 35 = 25 ma 3 25 = 2 ma 2 = 15 ma 15 1 = 1 ma = 1 ma 5 = 5 ma 1 2 3 4 5 6 7 8 9 1 V CE - Collector Emitter Voltage (non-sat) (V) N CTR - Normalized CTR (non-saturated) 1.2 1..8.6.4.2 = 5 ma Normalized to CTR value: = 5 ma, V CE = 5 V, T amb = 25 C -6-4 -2 2 4 6 8 1 12 T amb - Ambient Temperature ( C) Fig. 6 - Collector Current vs. Collector Emitter Voltage Fig. 9 - Normalized Current Transfer Ratio (non-saturated) vs. Ambient Temperature I CE - Leakage Current (na) 1 1 1 1 1.1.1 = ma V CE = 4 V V CE = 12 V V CE = 24 V -6-4 -2 2 4 6 8 1 12 T amb - Ambient Temperature ( C) N CTR - Normalized CTR (sat) 1.2 1..8.6.4.2 = 5 ma Normalized to CTR value: = 5 ma, V CE = 5 V, T amb = 25 C -6-4 -2 2 4 6 8 1 12 T amb - Ambient Temperature ( C) Fig. 7 - Leakage Current vs. Ambient Temperature Fig. 1 - Normalized Current Transfer Ratio (saturated) vs. Ambient Temperature I C - Collector Current (ma) 14 12 1 8 6 4 2 = 1 ma = 5 ma = 1 ma = 2 ma.1.2.3.4 V CE - Collector Emitter Voltage (V) V CEsat - Collector Emitter Voltage (V).4.35.3.25.2.15.1.5. = 1 ma I c = 1 ma I c = 2 ma I c = 5 ma -6-4 -2 2 4 6 8 1 12 T amb - Ambient Temperature ( C) Fig. 8 - Collector Current vs. Collector Emitter Voltage Fig. 11 - Collector Emitter Voltage vs. Ambient Temperature Rev. 3.1, 25-Jun-218 5 Document Number: 8351 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT11. Series N CTR - Normalized CTR (NS) 1.4 1.2 1..8.6.4.2 T amb = -55 C T amb = 25 C T amb = C T amb = 75 C T amb = 1 C Normalized to: = 5 ma, V CE = 5 V, T amb = 25 C.1 1 1 1 - Forward Current (ma) F CTR (khz) 1 V CC = 5 V 1 1 1.1 1 1 1 I C (ma) Fig. 12 - Normalized CTR (non-saturated) vs. Forward Current Fig. 15 - F CTR vs. Collector Current N CTR - Normalized CTR (sat) 1.2 1..8.6.4.2 V CE =.4 V Normalized to: = 5 ma, V CE = 5 V, T amb = 25 C T amb = C T amb = -55 C T amb = 25 C T amb = 75 C T amb = 1 C.1 1 1 1 - Forward Current (ma) t on, t off Switching Time (μs) 1 1 1 1.1 V CE = 5 V, I C = 2 ma t off (μs) t on (μs) 5 1 15 2 R L - Load Resistance (kω) Fig. 13 - Normalized CTR (saturated) vs. Forward Current Fig. 16 - Switching Time vs. Load Resistance -2-4 V CE = 5 V R L = 1 Ω Phase Angle (deg) -6-8 -1-12 -14-16 R L = 1 Ω 1 1 1 1 f - Frequency (khz) Fig. 14 - F CTR vs. Phase Angle Rev. 3.1, 25-Jun-218 6 Document Number: 8351 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
TCMT11. Series PACKAGE DIMENSIONS in millimeters 2.85 max. 2.6 ±.2 2. ±.1 4.4 typ..2 ±.5.4 ±.1 1.27 nom..1 ±.1.6 +.2 -.3 7. ±.3 Lead coplanarity.1 max. 4 3 Possible footprint 1.27.9 Pin One I.D. 5. 7.6 1 2 PACKAGE MARKING (example) MT11 V YWW 68 TAPE AND REEL PACKAGING in millimeters.3 ±.5 2 ±.1 4 ±.1 1.55 ±.5 Pin 1 1.75 ±.1 7.5 ±.1 4.4 7.4 ±.1 7.4 ±.1 16 ±.3 5 2.2 ±.1 2.6 ±.1 8 ±.1 2.95 ±.1 1.6 ±.1 Fig. 17 Rev. 3.1, 25-Jun-218 7 Document Number: 8351 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
SOLDER PROFILES 2nd line Temperature ( C) 3 25 2 15 1 255 C 24 C 217 C www.vishay.com Max. 12 s Axis Title Max. 3 s Max. 1 s Max. 26 C 245 C Max. ramp down 6 C/s 1 1 1 1st line 2nd line TCMT11. Series HANDLING AND STORAGE CONDITIONS ESD level: HBM class 2 Floor life: unlimited Conditions: T amb < 3 C, RH < 85 % Moisture sensitivity level 1, according to J-STD-2 5 Max. ramp up 3 C/s 19841 1 5 1 15 2 25 3 Time (s) Fig. 18 - Lead (Pb)-free Reflow Solder Profile According to J-STD-2 for SMD Devices Rev. 3.1, 25-Jun-218 8 Document Number: 8351 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91
Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 217 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 8-Feb-17 1 Document Number: 91