215-12-23 GaAlAs Light Emitting Diode (66 nm) Version 1.3 SFH 486 Features: Fabricated in a liquid phase epitaxy process Cathode is electrically connected to the case High reliability Spectral match with silicon photodetectors Hermetically sealed package Applications Photointerrupters IR remote control Sensor technology Light curtains Notes Depending on the mode of operation, these devices emit highly concentrated non visible infrared light which can be hazardous to the human eye. Products which incorporate these devices have to follow the safety precautions given in IEC 6825-1 and IEC 62471. Ordering Information ype: Radiant Intensity Ordering Code I e [mw/sr] I F = 5 ma, t p = 2 ms SFH 486 1.3 (.63) Q6272P553 Note: 18 A3 DIN 87 (O-18), flat glass cap, lead spacing 2.54 mm (1/1 ) anode making: projection at package bottom 215-12-23 1
Maximum Ratings ( A = 25 C) Parameter Symbol Values Unit Operation and storage temperature range op ; stg -4... 1 C Junction temperature j 125 C Reverse voltage V R 3 V Forward current I F 5 ma Surge current (t p 1 µs, D = ) Characteristics ( A = 25 C) I FSM 1 A Power consumption P tot 14 mw hermal resistance junction - ambient R thja 45 K / W hermal resistance junction - case R thjc 16 K / W Parameter Symbol Values Unit Peak wavelength (I F = 5 ma, t P = 2 ms) Spectral bandwidth at 5% of I max (I F = 5 ma, t p = 2 ms) (typ) λ peak 66 nm (typ) λ 25 nm Half angle (typ) ϕ ± 5 Dimensions of active chip area (typ) L x W.325 x.325 mm x mm Rise and fall time of I e ( 1% and 9% of I e max ) (I F = 5 ma, R L = 5 Ω) Capacitance (V R = V, f = 1 MHz) Forward voltage (I F = 5 ma, t P = 2 ms) Reverse current (V R = 3 V) otal radiant flux (I F =5 ma, t p =2 ms) emperature coefficient of I e or Φ e (I F = 5 ma, t p = 2 ms) emperature coefficient of V F (I F = 5 ma, t p = 2 ms) emperature coefficient of wavelength (I F = 5 ma, t p = 2 ms) (typ) t r, t f 1 ns (typ) C 25 pf (typ (max)) V F 2 ( 2.8) V I R.1 ( 1) µa (typ) Φ e 3 mw (typ) C I -.4 % / K (typ) C V -3 mv / K (typ) C λ.16 nm / K 215-12-23 2
Grouping ( A = 25 C) Group Min Radiant Intensity yp Radiant Intensity I F = 5 ma, t p = 2 ms I F = 1 A, t p = 1 µs I e, min [mw / sr] I e, typ [mw/ sr] SFH 486.63 15 Note: measured at a solid angle of Ω =.1 sr Relative Spectral Emission I rel = f(λ), A = 25 C Ι rel 1 % 8 6 1) page 8 OHR1869 1) page 8 Radiant Intensity I e / I e (5mA) = f(i F ), single pulse, t p = 2 µs, A = 25 C Ι e Ι e 5 ma 1 2 1 1 OHR187 4 1 2 1-1 6 65 7 nm 75 λ 1-2 1 1 2 1 1 ma 1 3 215-12-23 3
Max. Permissible Forward Current I F, max = f( C ), R thjc = 16 K / W Max. Permissible Forward Current I F, max = f( A ), R thja = 45 K / W 12 OHR39 12 OHR391 ma 1 ma 1 8 8 6 6 4 4 2 2 2 4 6 8 1 C 13 1) page 8 Forward Current I F = f(v F ), single pulse, t p = 1 µs, A = 25 C 3 1 ma 2 1 A OHR1871 2 4 6 8 1 C 13 Permissible Pulse Handling Capability I F = f(t p ), A = 25 C, duty cycle D = parameter 4 1 ma 1 3.1.2 D = t P D =.5.1.2.5 t P A OHR1872 1 1 1 2.5 DC 1 1 2 3 4 5 6 V 7 V F 1 1 1-5 1-4 1-3 1-2 1-1 s 1 1 t P 215-12-23 4
Radiation Characteristics I rel = f(ϕ), A = 25 C 1) page 8 4 3 2 ϕ 1 1. OHR389 5.8 6.6 7.4 8.2 9 1 1..8.6.4 2 4 6 8 1 12 Package Outline Chip position ø.45 14.5 12.5 (2.7) 1.1.9 2.54 mm spacing ø4.8 ø4.6 1.1.9 Cathode 4.5 3.45 Flat glass cap ø2.54 5.5 5.2 GMO6983 Dimensions in mm (inch). 215-12-23 5
Package Metal Can (O-18), solder tabs lead spacing 2.54 mm ( 1 / 1 "), anode marking: projection at package bottom Approximate Weight: 25. mg Recommended Solder Pad Dimensions in mm. Note: pad 1: anode 215-12-23 6
W Soldering IEC-6176-1 W 3 C 25 2 15 1 235 C - 26 C First wave Preheating 13 C 12 C 1 C 1 s max., max. contact time 5 s per wave < 15 K Second wave ypical OHA4645 Continuous line: typical process Dotted line: process limits Cooling ca. 3.5 K/s typical ca. 2 K/s ca. 5 K/s 5 Disclaimer 2 4 6 8 1 12 14 16 18 2 22 s 24 Language english will prevail in case of any discrepancies or deviations between the two language wordings. Attention please! he information describes the type of component and shall not be considered as assured characteristics. erms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version in the Internet. Packing Please use the recycling operators known to you. We can also help you get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components* may only be used in life-support devices** or systems with the express written approval of OSRAM OS. *) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system. **) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered. t 215-12-23 7
Glossary 1) ypical Values: Due to the special conditions of the manufacturing processes of LED, the typical data or calculated correlations of technical parameters can only reflect statistical figures. hese do not necessarily correspond to the actual parameters of each single product, which could differ from the typical data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical improvements, these typ. data will be changed without any further notice. 215-12-23 8
Published by OSRAM Opto Semiconductors GmbH Leibnizstraße 4, D-9355 Regensburg www.osram-os.com All Rights Reserved. 215-12-23 9