Powerex, Inc., 2 Hillis Street, Youngwood, Pennsylvania 15697-18 (724) 925-7272 PM1RSH12 Three Phase + Brake IGBT Inverter Output 1 Amperes/12 olts F S FO B R X T Y (15 TYP.) - DIA. (4 TYP.) X CC NC Q N N 12 NI CC P N A B C D P CC TEMP P 34 7 5 6 8 9 11 13 15 17 19 M E 1 12 14 16 18 U (4 TYP.) P B N U M M M M UN CC PC P FO PI CC H 2. ±.1 X.5 ±.1 MM P (6 TYP.) PC P FO G.6 ±.1 X.4 ±.1 MM P (19 TYP.) L R Z PI CC 1. 2. 3. UP 4. 5. 6. 7. P 8. 9. 1. 11. P 12. 13. UPC UP U FO CC UPI UPC U FO UPI PC FO PI PC FO PI NC J K 14. NI 15. BR 16. UN 17. N 18. N 19. FO 2. P 21. B 22. N 23. U 24. 25. Description: Powerex Intellimod Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 2kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: Complete Output Power Circuit Gate Drive Circuit B N U P Protection Logic Short Circuit Over Current Over Temperature Under oltage Outline Drawing and Circuit Diagram Dimensions Inches Millimeters A 3.98±.4 11.±1. B 3.7 94. C 3.48±.3 88.5±.8 D 2.7±.3 68.58±.8 E 2.66±.2 67.5±.5 F 2.36±.4 6.±1. G 1.85±.2 47.±.5 H 1.83±.3 46.5±.8 J 1.46 37. K 1.14 29. L.71±.4 18.±1. M.53±.1 13.5±.3 Dimensions Inches Millimeters N.41 P.4 1.16 Q.392 9.96 R.31 8. S.26 6.5 T.246 6.25 U.18 Rad. Rad. 4.5.18 Dia. Dia. 4.5.16±.2 4.±.5 X.14 3.5 Y.1±.1 4±.25 Z.2.5 Applications: Inverters UPS Motion/Servo Control Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM1RSH12 is a 12, 1 Ampere Intellimod Intelligent Power Module. Type Current Rating CES Amperes olts (x 1) PM 2 577
Powerex, Inc., 2 Hillis Street, Youngwood, Pennsylvania 15697-18 (724) 925-7272 PM1RSH12 1 Amperes/12 olts Absolute Maximum Ratings, T j = 25 C unless otherwise specified Characteristics Symbol PM1RSH12 Units Power Device Junction Temperature T j -2 to 15 C Storage Temperature T stg -4 to 125 C Case Operating Temperature T C -2 to 1 C Mounting Torque, M4 Mounting Screws 13 in-lb Module eight (Typical) 1 Grams Supply oltage Protected by OC and SC ( D = 13.5-16.5, Inverter Part, T j = 125 C) CC(prot.) 8 olts Isolation oltage, AC 1 minute, 6Hz Sinusoidal RMS 25 olts Control Sector Supply oltage Applied between ( UP1 - UPC, P1 - PC, P1 - PC, N1 - NC ) D 2 olts Input oltage Applied between (U P, P, P, U N, N, N, B r ) C 2 olts Fault Output Supply oltage FO 2 olts Fault Output Current I FO 2 ma IGBT Inverter Sector Collector-Emitter oltage ( D = 15, C = 15) CES 12 olts Collector Current, ± I C 1 Amperes Peak Collector Current, ± I CP 2 Amperes Supply oltage (Applied between P - N) CC 9 olts Supply oltage, Surge (Applied between P - N) CC(surge) 1 olts Collector Dissipation P C 62 atts Brake Sector Collector-Emitter oltage CES 12 olts Collector Current, ± I C 1 Amperes Peak Collector Current, ± I CP 2 Amperes Supply oltage (Applied between P - N) CC 9 olts Supply oltage, Surge (Applied between P - N) CC(surge) 1 olts Collector Dissipation P C 41 atts Diode Forward Current I F 1 Amperes Diode DC Reverse oltage R(DC) 12 olts 578
Powerex, Inc., 2 Hillis Street, Youngwood, Pennsylvania 15697-18 (724) 925-7272 PM1RSH12 1 Amperes/12 olts Electrical and Mechanical Characteristics, T j = 25 C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Control Sector Over Current Trip Level Inverter Part OC -2 C T 125 C 15 27 Amperes Over Current Trip Level Brake Part 15 27 Amperes Short Circuit Trip Level Inverter Part SC -2 C T 125 C 41 Amperes Short Circuit Trip Level Brake Part 41 Amperes Over Current Delay Time t off(oc) D = 15 1 µs Over Temperature Protection OT Trip Level 1 12 C OT R Reset Level 9 C Supply Circuit Under oltage Protection U Trip Level 1 12. 1 olts U R Reset Level 1 olts Supply oltage D Applied between UP1 - UPC, 13.5 15 16.5 olts P1 - PC, P1 - PC, N1 - NC Circuit Current I D D = 15, C = 15, N1 - NC 25 35 ma D = 15, C = 15, XP1 - XPC 7 1 ma Input ON Threshold oltage C(on) Applied between 1.2 1.8 olts Input OFF Threshold oltage C(off) U P, P, P, U N, N, N, B r 1.7 2. 2.3 olts PM Input Frequency f PM 3- Sinusoidal 15 2 khz Fault Output Current I FO(H) D = 15, FO = 15.1 ma I FO(L) D = 15, FO = 15 5 ma Minimum Fault Output Pulse idth t FO D = 15 1. 1.8 ms 579
Powerex, Inc., 2 Hillis Street, Youngwood, Pennsylvania 15697-18 (724) 925-7272 PM1RSH12 1 Amperes/12 olts Electrical and Mechanical Characteristics, T j = 25 C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IGBT Inverter Sector Collector Cutoff Current I CES CE = CES, T j = 25 C 1. ma CE = CES, T j = 125 C 1 ma Diode Forward oltage FM -I C = 1A, D = 15, C = 5 3.5 olts Collector-Emitter Saturation oltage CE(sat) D = 15, C =, I C = 1A 2.3 3.3 olts D = 15, C =, I C = 1A, 2.1 3.1 olts T j = 125 C Inductive Load Switching Times t on.4.7 µs t rr D = 15, C = ~ 15.15.3 µs t C(on) CC = 6, I C = 1A.3 1. µs t off T j = 125 C 1.7 2.9 µs t C(off).6 1.2 µs Brake Sector Collector-Emitter Saturation oltage CE(sat) D = 15, C =, I C = 1A, 2.8 3.8 olts T j = 25 C D = 15, C =, I C = 1A, 3.5 olts T j = 125 C Diode Forward oltage FM -I C = 1A, D = 15, C = 5 3.5 olts Collector Cutoff Current I CES CE = CES, T j = 25 C 1 ma CE = CES, T j = 125 C 1 ma 58
Powerex, Inc., 2 Hillis Street, Youngwood, Pennsylvania 15697-18 (724) 925-7272 PM1RSH12 1 Amperes/12 olts Thermal Characteristics Characteristic Symbol Condition Min. Typ. Max. Units Junction to Case Thermal Resistance R th(j-c)q Each Inverter IGBT 2. C/att R th(j-c)d Each Inverter FDi 5.5 C/att R th(c-f)q Each Brake IGBT 3. C/att R th(c-f)d Each Brake FDi 5.5 C/att Contact Thermal Resistance R th(c-f) Case to Fin Per Module,.44 C/att Thermal Grease Applied Recommended Conditions for Use Characteristic Symbol Condition alue Units Supply oltage CC Applied across P-N Terminals ~ 8 olts D Applied between UP1 - UPC, 15 ± olts N1 - NC, P1 - PC, P1 - PC Input ON oltage C(on) Applied between ~.8 olts Input OFF oltage C(off) U P, P, P, U N, N, N, B r 4. ~ D olts PM Input Frequency f PM Using Application Circuit 5 ~ 2 khz Minimum Dead Time t DEAD Input Signal µs 581
Powerex, Inc., 2 Hillis Street, Youngwood, Pennsylvania 15697-18 (724) 925-7272 PM1RSH12 1 Amperes/12 olts Inverter Part SATURATION OLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION OLTAGE CHARACTERISTICS (TYPICAL) PUT CHARACTERISTICS (TYPICAL) SATURATION OLTAGE CE(sat), (OLTS) 3. 2. 1. D = 15 C =.5 5 5 2 COLLECTOR-EMITTER SATURATION OLTAGE CE(sat), (OLTS) 3. 2. 1..5 I C = 5A C = 12 14 16 18 2 SUPPLY OLTAGE, D, (OLTS) 15. 1. 5. C = D = 17 13 1. 2. 3. 4. COLLECTOR-EMITTER OLTAGE, CE, (OLTS) 15 SITCHG TIMES, t on, t off, (µs) 1 SITCHG TIME S. COLLECTOR CURRENT (TYPICAL) CC = 6 D = 15 t off t on 1-1 1-2 1 1 2 1 1 2 SITCHG TIMES, t c(on), t c(off), (µs) 1 1-1 SITCHG TIME S. COLLECTOR CURRENT (TYPICAL) CC = 6 D = 15 t c(off) t c(on) REERSE RECOERY TIME, t rr, ( S) 1 3 1 2 REERSE RECOERY CURRENT S. COLLECTOR CURRENT (TYPICAL) CC = 6 D = 15 t rr I rr 1 1 1 2 EMITTER CURRENT, I C, (AMPERES) 1 2 REERSE RECOERY CURRENT, I rr, (AMPERES) DIODE FORARD CHARACTERISTICS OER CURRENT TRIP LEEL S. SUPPLY OLTAGE (TYPICAL) OER CURRENT TRIP LEEL S. TEMPERATURE (TYPICAL) DIODE FORARD CURRENT, I F, (AMPERES) 1 2 D = 15 OER CURRENT TRIP LEEL % (NORMALIZED) 14 12 1 8 6 1.5 1. 2. 3. 12 14 16 18 2 DIODE FORARD OLTAGE, F, (OLTS) SUPPLY OLTAGE, D, (OLTS) OER CURRENT TRIP LEEL % (NORMALIZED) 12 11 1 9 8 D = 15-2 2 6 1 14 JUNCTION TEMPERATURE, T j, ( o C) 582
Powerex, Inc., 2 Hillis Street, Youngwood, Pennsylvania 15697-18 (724) 925-7272 PM1RSH12 1 Amperes/12 olts Inverter Part FAULT PUT PULSE IDTH S. TEMPERATURE (TYPICAL) CONTROL SUPPLY OLTAGE TRIP-RESET LEEL TEMPERATURE DEPENDENCY (TYPICAL) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) FAULT PUT PULSE IDTH, t fo, (ms) 3. 2. 1. D = 15-5 5 1 15 JUNCTION TEMPERATURE, T j, ( o C) U TRIP-RESET LEEL, U t, U r, (OLTS) 15 14 13 12 11 U U r -5 5 1 15 JUNCTION TEMPERATURE, T j, ( o C) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED ALUE) 1 1-1 1-2 1-3 1-3 SGLE PULSE STANDARD ALUE = R th(j-c)q = 3. o C/ 1-2 1-1 1 TIME, (s) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FDi) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED ALUE) 1 1-1 1-2 1-3 1-3 SGLE PULSE STANDARD ALUE = R th(j-c)d = 5.5 o C/ 1-2 1-1 1 TIME, (s) 583
Powerex, Inc., 2 Hillis Street, Youngwood, Pennsylvania 15697-18 (724) 925-7272 PM1RSH12 1 Amperes/12 olts Brake Part SATURATION OLTAGE CE(sat), (OLTS) DIODE FORARD CURRENT, I F, (AMPERES) 3. 2. SATURATION OLTAGE CHARACTERISTICS (TYPICAL) 1. D = 15 C =.5 2 4 6 8 1 1 2 DIODE FORARD CHARACTERISTICS D = 15 1.5 1. 2. 3. 3.5 DIODE FORARD OLTAGE, F, (OLTS) COLLECTOR-EMITTER SATURATION OLTAGE CE(sat), (OLTS) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED ALUE) 3. 2. 1..5 1 1-1 1-2 COLLECTOR-EMITTER SATURATION OLTAGE CHARACTERISTICS (TYPICAL) C = I C = 1A 12 14 16 18 2 SUPPLY OLTAGE, D, (OLTS) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) SGLE PULSE STANDARD ALUE = R th(j-c)q = 2. o C/ 15 1 5 C = PUT CHARACTERISTICS (TYPICAL) D = 17 13 1 2 3 4 COLLECTOR-EMITTER OLTAGE, CE, (OLTS) 1-3 1-3 1-3 1-2 1-1 1 1-3 1-2 1-1 1 TIME, (s) TIME, (s) TRANSIENT IMPEDANCE, Z th(j-c), (NORMALIZED ALUE) 1 1-1 1-2 15 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FDi) SGLE PULSE STANDARD ALUE = R th(j-c)d = 5.5 o C/ 584