DATA SHEET Anti-Sulphur Thick Film Chip Resistor SAS(A/B) Series

DATA SHEET Anti-Sulphur Thick Film Chip Resistor SAS(A/B) Series 0.5% TO 5.0%, TCR -200 TO +400 SIZE: 0201/0402/0603/0805/1206/1210/2010/2512 RoHs Compliant May 08, 2017 V.4

Page: 2 of 1. SCOPE 1.1 This specification is applicable to lead and halogen free SAS series antisulphurated thick film chip resistors. 1.2 Lead free products mean lead free termination meets RoHS requirement. Pb contained in glass material of resistor element is exempted by RoHS directive. 1.3 The products are tested and passed based on the test conditions and methods defined in AEC-Q200. 2. PART NUMBERING SYSTEM Part Numbering is made in accordance with the following system: 3. RATING 3.1 Rated Power 3.1.1 Resistor Rated Power

Page: 3 of 3.2 Power Derating Characteristics Rated Power shall be the load power corresponding to nominal wattage suitable for continuous use at 70 C ambient temperatures. In case the ambient temperature exceeds 70 C, reduce the load power in accordance with Derating curve in Fig. 1. Fig.1 Power Derating Characteristics 3.3 Standard Atmospheric Condition Unless otherwise specified, the standard range of atmospheric conditions for making measurements and tests is as follows: Ambient Temperature = + 5 C to +35 C Relative Humidity Air Pressure = < 85% RH = 86 kpa to 106kPa If there may be any doubt about the results, measurement shall be made within the following limits: Ambient Temperature = 20 2 C Relative Humidity Air Pressure = 60 to 70% RH = 86 kpa to 106kPa 3.4 Operating Temperature Range -55 C to +155 C (SAS05-55 C to +125 C) 3.5 Storage Temperature Range -5 C to + 40 C 3.6 Flammability Rating Tested in accordance to UL-94, V-0

Page: 4 of 3.7 Moisture Sensitivity Level Rating: Level 1 3.8 Product Assurance ASJ resistor shall warranty 24 months from the date of shipment. 3.9 ASJ resistors are RoHS compliance in accordance to RoHS Directive 2011/65/EU. 3.10 Resistance, Resistance Tolerance and Temperature Coefficient of Resistance. 3.11 Rated Voltage The rated voltage is calculated from the rated power and nominal resistance by the following formula: E = P. R Where E : Rated Voltage (V) P : Rated Power (W) R : Nominal Resistance ( ) In case the value calculated by the formula exceeds the maximum working voltage given in Section 3.1.2, the maximum working voltage in Section 3.1.2 shall be regarded as the rated voltage. 3.12 Document review period: every 3 months

Page: 5 of 4. MARKING ON PRODUCT The nominal resistance shall be marked on the surface of each resistor Part Number Color Marking on Product SAS05 (0201) - No marking SAS10 (0402) - No marking SAS16 1) Tolerance : ±1.0% (F) Light Yellow (0603) SAS21 Four Numerals Marking (E96 Series) (0805) Light Yellow 0603 Three Characters Marking based on SAS32 E-96 marking standard. (1206) Light Yellow 2) Tolerance; ± 2.0% (G), ±5.0% (J) SAS40 Three Numerals Marking (1210) Light Yellow SAS50 (2010) Light Yellow SAS63 (2512) Light Yellow 4.1 Numeric Numbering 4.1.1 1% Tolerance : Four Numerals Marking First 3 digits are significant figures; fourth digit is number of zeros. Examples: Nominal Resistance Marking Remarks 1 1R00 1 X 10 0 = 1 10 10R0 10 X 10 0 = 10 100 1000 100 X 10 0 = 100 4.7K 4701 470 X 10 1 = 470 0 47K 4702 470 X 10 2 = 470 00 470K 4703 470 X 10 3 = 470 000 1M 1004 100 X 10 4 = 100 0000

Page: 6 of 5. DIMENSIONS, CONSTRUCTIONS AND MATERIALS 5.1 Dimensions SAS10 SAS16/ SAS21/SAS32/ SAS40/SAS50/ SAS63 Unit: mm

Page: 7 of 6. Reliability Test CHARACTERISTICS 1 High Temperature Exposure(Storage) SPECIFICATIONS Zero Ohm Resistance Refer to 1 0.5%, 1% : clause ±(1.0%+0.05Ω) 3.10. 2 2% 5% : ±(2.0%+0.10Ω) No mechanical damage TESTING CONDITIONS MIL-STD-202 Method 108 Put the specimens in the chamber with temperature of 125±3 C for 1000 hours. Then take them out to stabilize in room temperature 24±2hr or more and measure of its resistance variance rate. 2 Temperature Cycling Refer to clause 3.10. 3 Biased Humidity Refer to clause 3.10. 4 Operational Life Refer to clause 3.10. 1 0.5%, 1% : ±(1.0%+0.05Ω) 2 2% 5% : ±(2.0%+0.05Ω) No mechanical damage 1 0.5%, 1% ±(0.5%+0.05Ω) 2 2% 5% : ±(2.0%+0.10Ω) No mechanical damage, short or burning out phenomenon 1 0.5%, 1% ±(0.5%+0.05Ω) 2 2% 5% : ±(2.0%+0.10Ω) No mechanical damage, short or burning out phenomenon JESD22 Method JA-104 Put the specimens in the High & Low test chamber with temperature varies from -55 C to 155 C for 5 minute and total 1000 cycles. Take out to stabilize in room temperature for 24±2 hr or more, measure resistance variance rate. MIL-STD-202 Method 103 Solder the specimens on the test PCB board and put into the constant temperature humidity chamber with 85±2 C and 85±5%RH, apply test voltage that calculate based on 10% of rated power for 1000 hrs. Take them out to stabilize in room temperature for 24±2 hr or more to measure its resistance variance rate. MIL-STD-202 Method 108 Solder the specimens on the test PCB board and put into the chamber with temperature 125±3 C and load the rated voltage for 1000 hrs. Take out to stabilize in room temperature for 24±2hr or more, measure its resistance variance rate.

Page: 8 of 5 Physical Dimension Refer to clause 5.1, Dimension JESD22 Method JB-100 Measure Chip Size (L, W, H) by measuring tool. Measure conductor size with the high power microscope. 6 Resistance to Solvents Refer to clause 3.10. ±(0.5%+0.05Ω) No mechanical damage, peel off of G2 overcoat, marking or Leaching problem. MIL-STD-202 Method 215 Immersed the specimens into the isopropyl alcohol of 25±5 C for 3 0 +0.5 minute, rinse with water and stabilize for 48 hr or more, measure its resistance variance rate. 7 Resistance to soldering heat Refer to clause 3.10. ±(1.0%+0.05Ω) No cosmetic defect on terminal or peel off of side end. MIL-STD-202 Method 210 The specimens are fully immersed into the PB-Free solder pot, then take out to stabilize for 1 hour or more and measure its resistance variance rate. Temperature of solder pot : 260±5ºC Soldering duration : 10±1sec 8 ESD Refer to clause 3.10. 1 0.5%, 1% ±(2.0%+0.05Ω) 2 2% 5% : ±(3.0%+0.10Ω) No mechanical damage, short or burning out phenomenon. AEC-Q200-002 Put the specimens on the fixture and two(2) discharges (2KVDC) shall be applied to each, put one(1) with a positive polarity and one(1) with a negative polarity. Afterwards, the specimens stabilize for 30 min or more and measure its resistance variance rate. The test is perform with direct contact and regular discharge mode, the resistor and capacitor used on the spearhead is 2KΩ and 150pF

Page: 9 of 9 Solderability 1 Soldering cover over 95% 2 At the edge of terminal, the object underneath(eg. White ceramic) shall not expose. 10 Electrical Characterization 11 Board Flex Refer to clause 3.10. 12 Terminal Strength(SMD) 13 Sulfuration Test J-STD-002 Put the specimens in the apparatus of PCT, at a temperature of 105ºC, humidity of 100%RH, and air pressure of 1.22 x 105 Pa for a duration of 8 hours, leave the specimens in room temperature for 2 hour. Test item1(solder pot test):method A The specimens are immersed into the flux first, then fully immersed into the solder pot at a temperature of 235±5ºC for 5 +0/-0.5sec. Then rinse with water and observe the soldering coverage under microscope. Test item2(leaching Test):Method D The specimens are immersed into the flux first, then fully immersed into the solder pot at a temperature of 260±5ºC for 7±0.5sec. Then rinse with water and observe the soldering coverage under the microscope. Refer to clause 3.10 MIL-STD-202 Method 304 Refer to clause 3.10. Refer to clause 3.10. ±(1.0%+0.05Ω) No mechanical damage, peel off side end or chip crack ±(1.0%+0.05Ω) No mechanical damage, peel off side end ±(4.0%+0.10Ω) (R2 R1) TCR(ppm/ C) = R1(T2 T1) x106 R1: Resistance at room temperature (Ω) R2: Resistance at -55 or +125 (Ω) T1: Room temperature ( ) T2: Temperature -55 or +125 AEC-Q200-005 Solder the specimens on the test PCB and put the PCB onto the bending tester, add force at the center part of PCB, and measure its resistance variance rate in load. Bending dept D: 10, 16, 21 =5mm, 05, 32, 40 = 3mm 50, 63 = 2mm AEC-Q200-006 Solder the specimens on the test PCB and put them on the fixture, 1.8Kgf pushing force is applied with the test probe (dia. as R0.5)on the board and hold for 60sec, measure resistance variance rate in load. ASTM-B-809-95(Class: A) Put the test resistor in saturated vapor, at a temperature of 60±2 C, humidity 91 ~ 93%RH for 1000 hrs

Page: 10 of ASTM-B-809-95(Class: B) Put the test resistor in saturated vapor, at a temperature of 90±2 C, humidity 91 ~ 93%RH for 1000 hrs

Page: 11 of 6.1 Soldering Profile 6.1.1 IR Reflow +5 Remark: The peak temperature of soldering heat is 260 0 ⁰C for 10 seconds. 6.1.2 Wave Soldering 6.1.3 Soldering Iron : Temperature 350ºC±10ºC, dwell time shall be less than 3 sec.

Page: 12 of 7. TAPING 7.1 Structure of Taping Paper Carrier Embossed Plastic Carrier

Page: 13 of 7.2 Dimension 7.5.1 Dimension of Punched Paper Tape Carrier System (SAS05,SAS10) Remark: Pitch tolerance over any 10 pitches of Po is 0.2 mm Dimension of Punched Paper Tape Carrier System (SAS05, 10) (unit : mm) Code A B W E F T 1 SAS05 +0.1 0.68 0.05 0.38 0.03 8.00 0.10 1.75 0.10 3.50 0.05 0.42 0 SAS10 +0.2 1.15 0.05 0.65 0.05 8.00 0.20 1.75 0.10 3.50 0.05 0.42 0 Code T 2 P P0 10 x P0 P1 SAS05 0.28 0.02 2.00 0.05 4.00 0.05 40.0 0.20 2.00 0.05 SAS10 0.40 0.05 2.00 0.10 4.00 0.05 40.0 0.20 2.00 0.05

Page: 14 of 7.5.2 Dimension of Punched Paper Tape Carrier System /Plastic Embossed Carrier System (SAS16, 21, 32, 40) Remark: Pitch tolerance over any 10 pitches of Po is 0.2 mm Dimension of Punched Paper Tape Carrier System (SAS - 16, 21, 32, 40) Code A B W E F T1 T2 P P0 P1 SAS16 +0.2 1.8 0.10 1.0 0.10 8.0 0.20 1.75 0.10 3.50 0.05 0.60 0 0.60 0.10 4.0 0.10 4.0 0.05 2.0 0.05 SAS21 +0.2 2.3 0.10 1.55 0.1 8.0 0.20 1.75 0.10 3.50 0.05 0.75 0 0.75 0.10 4.0 0.10 4.0 0.05 2.0 0.05 SAS32 +0.2 3.5 0.20 1.9 0.20 8.0 0.20 1.75 0.10 3.50 0.05 0.75 0 0.75 0.10 4.0 0.10 4.0 0.05 2.0 0.05 SAS40 +0.2 3.5 0.20 2.8 0.20 8.0 0.20 1.75 0.10 3.50 0.05 0.75 0 0.75 0.10 4.0 0.10 4.0 0.05 2.0 0.05 Dimension of Plastic Embossed Carrier System (SAS - 50, 63) Code A B W E F T1 T2 P P0 P1 SAS50 5.5 0.20 2.8 0.20 12.0 0.20 1.75 0.10 5.50 0.05 1.10 0.15 0.23 0.15 4.0 0.10 4.0 0.05 2.0 0.05 SAS63 6.7 0.20 3.4 0.20 12.0 0.20 1.75 0.10 5.50 0.05 1.10 0.15 0.23 0.15 4.0 0.10 4.0 0.05 2.0 0.05

Page: 15 of 7.7 Packaging 7.7.1 Taping 7.7.1.1 Quantity Tape and Reels Code Quantity Model Remarks SAS05 10000 pcs 7 Reel 13 Reel upon request SAS10 10000 pcs 7 Reel 13 Reel upon request SAS16 5000 pcs 7 Reel SAS21 5000 pcs 7 Reel 10 000 or 20 000 pcs on request SAS32 5000 pcs 7 Reel SAS40 5000 pcs 7 Reel SAS50 4000 pcs 7 Reel - SAS63 4000 pcs 7 Reel - 7.7.2 Identification Production label that indicates the 8 digits lot number, product type, resistance value and tolerance shall be pasted on the surface of each reel. 7.7.3 Packaging Reel Box Dimension Reel Box Number of Reels 5 60 6 mm 25K Box 5 5 120 6 mm 50K Box 10

Page: 16 of 7.7.4 Reel Dimensions D C B r B W1 A W t Model A B C D W W 1 t r 7 Reel (5K) (except 0402 10K) 178 2.0 60min 13 0.2 2.0 0.5 11 0.1 14.4 max 1.0 0.1 1.0 7 Reel (4K) 178 2.0 60min 13 0.2 2.0 0.5 13 1.0 14.4 max 1.2 0.1 1.0 7 Reel (10K) 178 2.0 60min 13 0.2 2.0 0.5 11 0.1 14.4 max 1.0 0.1 1.0 10 Reel (10K) 254 2.0 60min 13 0.2 2.0 0.5 11 1.0 14.4 max 1.5 0.1 1.0 13 Reel (20K) 330 2.0 60min 13 0.2 2.0 0.5 11 1.0 14.4 max 2.1 0.1-13 Reel (20K) 330 1.0 100±1 13.5±0.5 2~3±0.5 10±0.5 - - -

Page: 17 of 8. SURFACE MOUNT LAND PATTERNS A C SMC B Product ( Type ) Land Dimension A B C SAS05 0.012 [0.3] 0.039[1.0] 0.016 [ 0.4 ] SAS10 0.020 [0.5] 0.059 [1.5] 0.024 [ 0.6 ] SAS16 0.031 [0.8] 0.083 [2.1] 0.035 [ 0.9 ] SAS21 0.047 [1.2] 0.1 [3.0] 0.051 [ 1.3 ] SAS32 0.087 [2.2] 0.165 [4.2] 0.063 [ 1.6 ] SAS40 0.087 [2.2] 0.165 [4.2] 0.110 [ 2.8 ] SAS50 0.138 [3.5] 0.240 [6.1] 0.110 [ 2.8 ] SAS63 0.149 [3.8] 0.315 [8.0] 0.137 [ 3.5 ] 9. Measurement Point

Page: of 10. REVISION HISTORY REVISION DATE CHANGE NOTIFICATION DESCRIPTION Initial Release Version. 1 Version. 2 February 13,2015 October 03, 2016 Update information for :- Part Numbering System Rated Power Table Power Derating Characteristic Resistance, Tolerance, TCR Reliability test Punch paper tape Packaging Reel Dimension Version.3 Version.4 November 16, 2016 May 08 2017 Refer to PCN-ECO NO.: 01/RL/2016 Update clause 5.1 L1 dimension for SAS05 Typo error in clause 5.1 Insert Measurement Point in clause 9 Rename to SAS(A/B) Series