UGN3503 HLL EFFECT SENSOR The UGN3503LT, UGN3503U, and UGN3503U Hall-effect sensors accurately track extremely small changes in magnetic flux density changes generally too small to operate Hall-effect switches. X V CC SUPPLY GROUND OUTPUT Dwg. PH-006 Pinning is shown viewed from branded side. s motion detectors, gear tooth sensors, and proximity detectors, they are magnetically driven mirrors of mechanical events. s sensitive monitors of electromagnets, they can effectively measure a system's performance with negligible system loading while providing isolation from contaminated and electrically noisy environments. Each Hall-effect integrated circuit includes a Hall sensing element, linear amplifier, and emitter-follower output stage. Problems associated with handling tiny analog signals are minimized by having the Hall cell and amplifier on a single chip. Three package styles provide a magnetically optimized package for most applications. Package suffix LT is a miniature SOT-89/TO- 243 transistor package for surface-mount applications; suffix U is a miniature three-lead plastic SIP, while U is a three-lead ultra-mini- SIP. ll devices are rated for continuous operation over the temperature range of -20 C to +85 C. FETURES Extremely Sensitive Flat Response to 23 khz Low-Noise Output 4.5 V to 6 V Operation Magnetically Optimized Package BSOLUTE MXIMUM RTINGS Supply Voltage, V CC... 8 V Magnetic Flux Density, B... Unlimited Operating Temperature Range, T... -20 C to +85 C Storage Temperature Range, T S... -65 C to +150 C lways order by complete part number, e.g., UGN3503U.
FUNCTIONL BLOCK DIGRM 1 V CC REG. X 3 OUTPUT 2 GROUND Dwg. FH-007 ELECTRICL CHRCTERISTICS at T = +25 C, V CC = 5 V Limits Characteristic Symbol Test Conditions Min. Typ. Max. Units Operating Voltage V CC 4.5 6.0 V Supply Current I CC 9.0 13 m Quiescent Output Voltage V OUT B = 0 G 2.25 2.50 2.75 V Sensitivity V OUT B = 0 G to ±900 G 0.75 1.30 1.75 mv/g Bandwidth (-3 db) BW 23 khz Broadband Output Noise V out BW = 10 Hz to 10 khz 90 µv Output Resistance R OUT 50 220 Ω ll output-voltage measurements are made with a voltmeter having an input impedance of at least 10 kω. Magnetic flux density is measured at most sensitive area of device located 0.0165" (0.42 mm) below the branded face of the U package; 0.0195" (0.50 mm) below the branded face of the U package; and 0.0305" (0.775 mm) below the branded face of the LT package.
OUTPUT VOLTGE S FUNCTION OF TEMPERTURE OUTPUT NOISE S FUNCTION OF FREQUENCY 4.0 10 OUTPUT IN VOLTS 3.5 3.0 2.5 B= +500G B = 0G B= -500G V CC = 5V OUTPUT NOISE IN µ Vrms HZ 8.0 6.0 4.0 V CC = +5V T = +25 C 1.5 40 20 0 +25 +85 +125 MBIENT TEMPERTURE IN C Dwg. -12,573 0 10 100 1K 10K FREQUENCY IN HZ Dwg. -12,505 SUPPLY CURRENT S FUNCTION OF SUPPLY VOLTGE 12 DEVICE SENSITIVITY S FUNCTION OF SUPPLY VOLTGE 2.5 SUPPLY CURRENT IN m 11 10 9.0 B = 0G T = +25 C ICL SENSITIVITY IN V/G 1.5 1.0 T = +25 C 8.0 0.5 7.0 SUPPLY VOLTGE IN VOLTS Dwg. -12,506 0 SUPPLY VOLTGE IN VOLTS Dwg. -12,507 OUTPUT NULL VOLTGE S FUNCTION OF SUPPLY VOLTGE OUTPUT NULL VOLTGE IN VOLTS 5.0 4.0 3.0 1.0 B = 0G T = +25 C 0 SUPPLY VOLTGE IN VOLTS Dwg. -12,508 ITY ND SYMMETRY S FUNCTION OF SUPPLY VOLTGE ITY ND SYMMETRY IN PERCENT 100 99 98 97 96 OUTPUT SYMMETRY ITY BELOW NULL B = -900G ITY BOVE NULL B = +900G T = +25 C 95 SUPPLY VOLTGE IN VOLTS Dwg.-12,509
NOTCH SENSOR GER TOOTH SENSOR N Dwg. -12,574 OPERTION The output null voltage (B = 0 G) is nominally one-half the supply voltage. south magnetic pole, presented to the branded face of the Halleffect sensor will drive the output higher than the null voltage level. north magnetic pole will drive the output below the null level. In operation, instantaneous and proportional output-voltage levels are dependent on magnetic flux density at the most sensitive area of the device. Greatest sensitivity is obtained with a supply voltage of 6 V, but at the cost of increased supply current and a slight loss of output symmetry. The sensor's output is usually capacitively coupled to an amplifier that boosts the output above the millivolt level. In two applications shown, a permanent bias magnet is attached with epoxy glue to the back of the epoxy package. The presence of ferrous material at the face of the package acts as a flux concentrator. The south pole of a magnet is attached to the back of the package if the Hall-effect IC is to sense the presence of ferrous material. The north pole of a magnet is attached to the back surface if the integrated circuit is to sense the absence of ferrous matrial. Calibrated linear Hall devices, which can be used to determine the actual flux density presented to the sensor in a particular application, are available. SENSOR LOCTIONS CTIVE RE DEPTH 0.0165" 0.42 mm NOM SUFFIX U 0.093" 2.37 mm 3 2 1 Dwg. -12,512 0.072" 1.83 mm CURRENT MONITOR BRNDED SURFCE Dwg. MH-002-5D SUFFIX LT SUFFIX U CTIVE RE DEPTH 0.0305" 0.775 mm NOM 0.091" 2.32 mm CTIVE RE DEPTH 0.0195" 0.50 mm NOM 0.084" 2.13 mm 0.042" 1.08 mm 0.056" 1.43 mm BRNDED SURFCE Dwg. -12,513 Dwg. MH-008-9 Dwg. MH-011-3D
Dimensions in Inches (for reference only) UGN3503LT (SOT89/TO-243) Dimensions in Millimeters (controlling dimensions) 0.181 0.173 0.072 0.064 0.063 0.055 0.0138 4.60 4.40 1.83 1.62 1.60 1.40 0.35 0.167 0.155 0.102 0.090 0.090 0.084 4.25 3.94 2.60 2.29 2.29 2.13 0.047 0.035 0.059 0.118 0.0189 0.0142 0.0221 Dwg. M-009-3 in 1.20 0.89 1.50 3.00 0.48 0.36 0.56 Dwg. M-009-3 mm 0.098 0.079 2.5 B 0.031 B 0.8 0.102 0.181 2.6 4.6 1 2 3 0.047 1.2 0.028 0.031 Pads 1, 2, 3, and Standard SOT89 Layout Pads 1, 2, 3, and B Low-Stress Version Pads 1, 2, and 3 only Lowest Stress, But Not Self ligning Dwg. M-012-3 in 0.7 0.8 Pads 1, 2, 3, and Standard SOT89 Layout Pads 1, 2, 3, and B Low-Stress Version Pads 1, 2, and 3 only Lowest Stress, But Not Self ligning Dwg. M-012-3 mm NOTES: 1. Exact body and lead configuration at vendor s option within limits shown. 2. Supplied in bulk pack (500 pieces per bag) or add "TR" to part number for tape and reel. 3. Only low-temperature ( 240 C) reflow-soldering techniques are recommended for SOT89 devices.
UGN3503U Dimensions in Inches (controlling dimensions) Dimensions in Millimeters (for reference only) 0.183 0.178 4.65 4.52 0.063 0.059 1.60 1.50 0.181 0.176 4.60 4.47 0.086 MX 0.018 2.18 MX 0.46 0.600 0.560 0.0138 15.24 14.23 0.35 0.0189 0.0142 0.48 0.36 0.100 0.050 Dwg. MH-003E in 2.54 1.27 Dwg. MH-003E mm Devices in the U package are NOT RECOMMENDED FOR NEW DESIGN NOTES: 1. Tolerances on package height and width represent allowable mold offsets. Dimensions given are measured at the widest point (parting line). 2. Exact body and lead configuration at vendor s option within limits shown. 3. Height does not include mold gate flash. 4. Recommended minimum PWB hole diameter to clear transition area is 0.035" (0.89 mm). 5. Minimum lead length was 0.500" (12.70 mm). If existing product to the original specifications is not acceptable, contact sales office before ordering.
Dimensions in Inches (controlling dimensions) UGN3503U Dimensions in Millimeters (for reference only) 0.164 0.159 4.17 4.04 0.062 0.058 1.57 1.47 0.122 0.117 3.10 2.97 0.085 MX 0.031 2.16 MX 0.79 0.640 0.600 0.0138 16.26 15.24 0.35 0.0189 0.0142 0.48 0.36 0.050 Dwg. MH-014E in 1.27 Dwg. MH-014E mm NOTES: 1. Tolerances on package height and width represent allowable mold offsets. Dimensions given are measured at the widest point (parting line). 2. Exact body and lead configuration at vendor s option within limits shown. 3. Height does not include mold gate flash. 4. Recommended minimum PWB hole diameter to clear transition area is 0.035" (0.89 mm). 5. Where no tolerance is specified, dimension is nominal. 6. Supplied in bulk pack (500 pieces per bag). Radial Lead Form (order UGN3503U-LC) 0.620" 0.500" (15.7 mm 12.7 mm) 0.108" (2.74 mm) 0.100" (2.5 mm) Dwg. MH-026 NOTE: Lead-form dimensions are the nominals produced on the forming equipment. No dimensional tolerance is implied or guaranteed for bulk packaging (500 pieces per bag).