Adaptation of Pb-Bi Cooled, Metal Fuel Subcritical Reactor for Use with a Tokamak Fusion Neutron Source E. Hoffman, W. Stacey, G. Kessler, D. Ulevich, J. Mandrekas, A. Mauer, C. Kirby, D. Stopp, J. Noble Fusion Research Center Georgia Institute of Technology Atlanta, Ga 30332 USA
Study Objectives Develop a nuclear design concept for a sub-critical transmutation reactor driven by a D-T tokamak fusion neutron source. Adapt nuclear technology being developed for ATW to identify a transmutation blanket. Analyze the performance of a tokamak transmutation facility.
Adaptation of ATW Nuclear Technology to a Fusion Driven Reactor Tritium Production Addition of lithium for tritium self-sufficiency Tokamak Geometry
Plasma Chamber Tokamak Design Ohmic Heating Coils Toroidal Field Coils Reflector, Shield & Vacuum Vessel First Wall 1 Meter Reactor Region
Midplane Radial Build OH gap TF in 2a reac ou TF R fc R mag R o R fc = flux core radius = 1.20 m OH = OH solenoid = 0.25 TF = TF coil = 0.35 in = inner refl/shld = 0.40 a = minor radius = 0.90 reac = reactor = 0.40 ou = outer refl/shld = 0.30 gap = outer gap = tbd R o = major radius = 3.10 R mag = magnet radius = 1.80 Note: refl/shld includes first wall, reflector, shield, and vacuum vessel
Tokamak Subcritical Reactor Reactor Plasma First Wall 1 Meter
Hexagonal Fuel Assembly Fuel Cell Pin Diameter 0.635 cm Cladding Thickness 0.056 cm Pitch-to-Diameter 1.727 Fuel Assembly 210 Fuel Pins, 7 Structural Pins Volume Fractions Fuel 0.14, Structure 0.103, Coolant 0.695 Materials Dispersion Fuel TRU-10Zr/Zr Structure/Clad HT-9
System Design Constraints Plasma Physics Constraints Tokamak Geometry Thermal Constraints Power Density Radiation Damage Constraints Shield Thickness Fuel residence time Engineering Constraints Lithium Concentration Magnet Sizing Self Imposed Total Power Maximum Neutron Multiplication (k)
Magnet Radiation Damage Limits Reflector / Shield Thickness Driver Designed as Lifetime Component 40 Full Power Years Used Radiation Damage Limits Ceramic Insulators Fast fluence limit = 4E+22 n/cm 2 Optimize Shield to Dose Limits Organic Insulators Dose limit = 1E11 Rads
Limit Tritium Balance dt ( t) = (1 α)* T& ( t) F& ( t) λtt ( t) dt T ( t) = Tritium inventory α = fractional loss of tritium T& ( t) = Tritium productionrate F& ( t) = Fusion rate λ T T T t T EOC BOC EOC down = Tritium decay constant T BOC e λ T t down = Startup tritium inventory at the beginning of = Tritium inventory at the end of cycle = Down time between cycles cycle
Time Behavior of Tritium Inventory Tritium Inventory Minimum End of Cycle Inventory Startup Inventory Maximum Cycle Length 0 Time
Lithium Concentrations Tritium Production Cross Sections 14 MeV Fission Spectrum Li6 7.5% 28.0 mb 330.7 mb Li7 92.5% 302.9 mb 20.0 mb Nat Li 282.3 mb 43.3 mb Lithium Lead (Li 17 Pb 83 ) Enrichment ~20a/o Li-6 Lithium in Lead BismuthEutectic (Pb 45 Bi 55 ) (Li x Pb y Bi z ) Range of enrichments depending on x Assuming 5% by volume Li enrichment to ~40 a/o Li-6
Other Design Limits Parameter Limit P Blanket 3000 MWt (~1 GWe) k 0.95 Power Density 175 kw/l Cladding Lifetime 25% BU - go to DPA limit First Wall Lifetime DPA Limit ~ 200 MW P fus
Equilibrium Fuel Cycle LWR SNF UREX Pyro Transmute Waste
REBUS Fuel Cycle Code ANL Fast Reactor Fuel Cycle Code Same Code used by ANL for ATW Calculations Equilibrium Cycle Calculations Input Target Beginning of Cycle K-eff Input Irradiation Cycle Parameters Input External Cycle Parameters Iterates on Fuel Enrichment Volume HM/(Volume Zr + Volume HM) Calculates Fuel Cycle Parameters Enrichment, Isotopic Composition Power Density, Burnup, Source Strength Mass Flow, Feed, Recycle, Waste
Power Production
Cycle Variation of Key Parameters
Preliminary Result Case Name LBE-5-40 LiPb-20 Coolant Lead-Bismuth w/ Lithium Lithium Lead Li-6 Enrichment 40 a/o Li-6 20 a/o Li-6 Li Volume Fraction 5 v/o n/a Fuel Batches 3 3 Cycle Length (FPD) 624 624 Enrichment 43% 45% BOC k 0.95 0.95 EOC k 0.86 0.86 BOC Fusion Power 41 MW 41 MW EOC Fusion Power 127 MW 125 MW Discharge Burnup 21% 20% Cladding Damage 112 dpa 107 dpa FW Damage 22 dpa/cycle 21 dpa/cycle Tritium EOC / BOC 16 30 Reactor Power Density 118 kw/l 118 kw/l
Preliminary Transmutation Results Cycle Length = 624 FPD = 1.7 FPY Fuel Residence Time = 3 cycles Transmutation Rate ~2 MTHM/cycle ~ 1.1 MT/FPY
Fuel Composition LBE-5-40 LiPb-20 SNF Fresh Discharged Fresh Discharged Feed Fuel Fuel Loading (MTHM) 10.2 8.2 10.5 8.6 Inventory* (MTHM) 27.5 25.6 28.5 26.6 U 0.4% 4.4% 5.2% 4.5% 5.3% Np 4.2% 3.6% 3.4% 3.5% 3.3% Pu 83.2% 77.9% 76.6% 77.9% 76.6% Pu-239 52.8% 30.2% 24.4% 29.7% 24.1% Am 10.0% 13.2% 13.6% 13.2% 13.5% Cm 0.1% 0.9% 1.3% 0.9% 1.4% * Inventory is the beginning of cycle & end of cycle actinide mass
Preliminary Conclusions Nuclear design feasible Two Pb cooled options 5% Li enriched to 40% Li-6 in LBE Li-17Pb-83 enriched to 20% Li-6 Metal Fuel TRU-10Zr dispersed in Zr 30-45 v/o TRU Transmutation fuel cycle 3 batch, 1.5-2 FPY cycle ~2 MTHM fissioned per cycle
Future Work Optimized Fusion Cycle Batches, Cycle Lengths, Shielding, Lithium, Reactivity Compensation,... Waste Management Performance Repository Requirements, Toxicity, Proliferation, Decay Heat,... Examine Criticality Safety Margin High Leakage Configuration Benchmarking